Asus P5K SE User Manual

P5K SE
Motherboard
E3202
First Edition V1 May 2007
Copyright © 2007 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to infringe.
ii
Contents
Notices ........................................................................................................ vii
Safety information .................................................................................... viii
About this guide ......................................................................................... ix
P5K SE specications summary ............................................................... xi
Chapter1: Product introduction
1.1 Welcome! ...................................................................................... 1-1
1.2 Package contents .........................................................................
1.3 Special features ............................................................................
1.3.1 Product highlights ...........................................................
1.3.2 ASUS AI Lifestyle features ..............................................
1.3.3 ASUS Stylish features .....................................................
1.3.4 ASUS Intelligent Overclocking features ..........................
Chapter2: Hardware information
2.1 Before you proceed ..................................................................... 2-1
2.2 Motherboard overview .................................................................
2.2.1 Placement direction ........................................................
2.2.2 Screw holes ....................................................................
2.2.3 Motherboard layout .........................................................
2.2.4 Layout contents ...............................................................
2.3 Central Processing Unit (CPU) ...................................................
2.3.1 Installing the CPU ...........................................................
2.3.2 Installing the CPU heatsink and fan ................................
2.3.3 Uninstalling the CPU heatsink and fan ..........................
2.4 System memory .........................................................................
2.4.1 Overview .......................................................................
2.4.2 Memory congurations ..................................................
2.4.3 Installing a DIMM ..........................................................
2.4.4 Removing a DIMM ........................................................
2.5 Expansion slots ..........................................................................
2.5.1 Installing an expansion card .........................................
2.5.2 Conguring an expansion card .....................................
2.5.3 Interrupt assignments ...................................................
2.5.4 PCI slots ........................................................................
2.5.5 PCI Express x1 slots .....................................................
2.5.6 PCI Express x16 slots ...................................................
1-1
1-2
1-2
1-4
1-5
1-6
2-2
2-2
2-2
2-3
2-4
2-6
2-7
2-9
2-11
2-13
2-13
2-14
2-18
2-18
2-19
2-19
2-19
2-20
2-21
2-21
2-21
iii
Contents
2.6 Jumper ........................................................................................ 2-22
2.7 Connectors .................................................................................
2.7.1 Rear panel connectors ..................................................
2.7.2 Internal connectors .......................................................
Chapter3: Powering up
3.1 Starting up for the rst time ........................................................ 3-1
3.2 Turning off the computer .............................................................
3.2.1 Using the OS shut down function ....................................
3.2.2 Using the dual function power switch ..............................
Chapter4: BIOS setup
4.1 Managing and updating your BIOS ............................................ 4-1
4.1.1 ASUS Update utility ........................................................
4.1.2 Creating a bootable oppy disk .......................................
4.1.3 ASUS EZ Flash 2 utility ...................................................
4.1.4 AFUDOS utility ................................................................
4.1.5 ASUS CrashFree BIOS 3 utility ......................................
4.2 BIOS setup program ....................................................................
4.2.1 BIOS menu screen ........................................................
4.2.2 Menu bar .......................................................................
4.2.3 Navigation keys .............................................................
4.2.4 Menu items ....................................................................
4.2.5 Sub-menu items .............................................................
4.2.6 Conguration elds ........................................................
4.2.7 Pop-up window ..............................................................
4.2.8 Scroll bar ........................................................................
4.2.9 General help ..................................................................
4.3 Main menu ..................................................................................
4.3.1 System Time .................................................................
4.3.2 System Date .................................................................
4.3.3 Legacy Diskette A .........................................................
4.3.4
4.3.5 SATA Conguration .......................................................
4.3.6 System Information .......................................................
SATA 1~4 .........................................................................................4-13
2-24
2-24
2-26
3-2
3-2
3-2
4-1
4-4
4-5
4-6
4-8
4-9
4-10
4-10
4-10
4-11
4-11
4-11
4-11
4-11
4-11
4-12
4-12
4-12
4-12
4-14
4-15
iv
Contents
4.4 Advanced menu ......................................................................... 4-16
4.4.1 Jumperfree Conguration .............................................
4.4.2 USB Conguration ........................................................
4.4.3 CPU Conguration ........................................................
4.4.4 Chipset ..........................................................................
4.4.5 OnBoard Devices Conguration ...................................
4.4.6 PCI PnP ........................................................................
4.5 Power menu ................................................................................
4.5.1 Suspend Mode [Auto] ...................................................
4.5.2 Repost Video on S3 Resume [Disabled] .......................
4.5.3 ACPI Version [Disabled] ................................................
4.5.4 ACPI APIC Support [Enabled] .......................................
4.5.5 APM Conguration ........................................................
4.5.6 Hardware Monitor .........................................................
4.6 Boot menu ..................................................................................
4.6.1 Boot Device Priority ......................................................
4.6.2 Boot Settings Conguration ..........................................
4.6.3 Security .........................................................................
4.7 Tools menu .................................................................................
4.7.1 ASUS EZ Flash 2 ..........................................................
4.7.2 ASUS O.C. Prole .........................................................
4.8 Exit menu ....................................................................................
4-16
4-20
4-21
4-22
4-23
4-24
4-25
4-25
4-25
4-25
4-25
4-26
4-27
4-29
4-29
4-30
4-31
4-33
4-33
4-34
4-35
Chapter5: Software support
5.1 Installing an operating system ................................................... 5-1
5.2.1 Running the support CD .................................................
5.2.2 Drivers menu ...................................................................
5.2.3 Utilities menu ..................................................................
5.2.4 Manual menu ..................................................................
5.2.5 ASUS Contact information ..............................................
5.2.6 Other information ............................................................
5.3 Software information ...................................................................
5.3.1 ASUS MyLogo2™ ...........................................................
5.3.2 Audio congurations .....................................................
5.3.3 ASUS PC Probe II .........................................................
5.3.4 ASUS AI Suite ...............................................................
5-1
5-2
5-3
5-5
5-5
5-6
5-8
5-8
5-10
5-14
5-20
v
Contents
5.3.5 ASUS AI Gear2 ............................................................. 5-22
5.3.6 ASUS AI Nap ................................................................
5.3.7 ASUS Q-Fan 2 ..............................................................
5.3.8 ASUS AI Booster ...........................................................
Appendix: CPU features
A.1 Intel® EM64T ..................................................................................A-1
®
A.2 Enhanced Intel SpeedStep
A.2.1 System requirements ......................................................
A.2.2 Using the EIST ................................................................
®
A.3 Intel
Hyper-Threading Technology ...........................................A-3
Technology (EIST) ........................A-1
5-23
5-24
5-25
A-1
A-2
vi
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modications
to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vii
Safety information
Electrical safety
To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.
Seek professional assistance before using an adpater or extension cord. These devices could interrupt the grounding circuit.
Make sure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.
If the power supply is broken, do not try to x it by yourself. Contact a qualied service technician or your retailer.
Operation safety
Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package.
Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet.
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualied
service technician or your retailer.
viii
This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.
About this guide
This user guide contains the information you need when installing and conguring
the motherboard.
How this guide is organized
This guide contains the following parts:
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it supports.
Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the switches, jumpers, and connectors on the motherboard.
Chapter 3: Powering up
This chapter describes the power up sequence and ways of shutting down the system.
Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter 5: Software support
This chapter describes the contents of the support CD that comes with the motherboard package.
Appendix: CPU features
The Appendix describes the CPU features and technologies that the motherboard supports.
Where to nd more information
Refer to the following sources for additional information and for product and software updates.
1. ASUS websites
The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.
2. Optional documentation
Your product package may include optional documentation, such as warranty
yers, that may have been added by your dealer. These documents are not
part of the standard package.
ix
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
Typography
Bold text Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or Return key.
<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously, the
key names are connected with a plus sign (+).
Example: <Ctrl>+<Alt>+<D>
Command Means that you must type the command exactly as
shown.
Example: At the DOS prompt, type the command line:
afudos /iP5KSE.ROM
x
P5K SE specications summary
CPU LGA775 socket for Intel® Core™2 Extreme / Core™2
Chipset Intel® P35 / ICH9 with Intel® Fast Memory Access
System bus 1333/1066/800 MHz
Memory Dual-channel memory architecture
Expansion slots 1 x PCI Express™ x16 slot
Storage Southbridge
LAN PCIe Gigabit LAN controller featuring AI NET2
Audio Realtek® ALC883 8-channel High-Denition Audio CODEC
USB 12 x USB 2.0 ports (6 at mid-board, 6 at back panel)
Quad / Core™2 Duo / Pentium® Extreme / Pentium® D / Pentium® 4 processors Compatible with Intel® 05B/05A/06 processors Supports Intel® next-generation 45nm multi-core CPU
Technology
- 4 x 240-pin DIMM sockets support unbuffered non-ECC DDR2 1066*/800/667MHz memory modules
- Supports up to 8 GB system memory
* The chipset ofcially supports the memory frequency up to DDR2 800MHz. Tuned by the ASUS Super Memspeed
Technology, this motherboard natively supports up to DDR2 1066MHz. Refer to www.asus.com or this user manual for the
Memory QVL (Qualied Vendors Lists).
3 x PCI Express™ x1 slots 2 x PCI slots
- 4 x Serial ATA 3.0 Gb/s ports Marvell® 88SE6111 PATA and SATA controller supports:
- 1 x UltraDMA 133/100/66 for up to 2 PATA devices
- 1 x External SATA 3.0 Gb/s port (SATA On-the-Go)
- Supports Jack-Sensing, Enumeration, Multi-Streaming
- Coaxial S/PDIF out ports at back I/O
- ASUS Noise Filter
(continued on the next page)
xi
P5K SE specications summary
AI Lifestyle Unique features
Other features ASUS MyLogo2
ASUS Exclusive Overclocking features
Rear panel connectors 1 x PS/2 keyboard port
ASUS Quiet Thermal Solution:
- ASUS AI Gear 2
- ASUS AI Nap
- ASUS Q-Fan 2 ASUS Crystal Sound:
- ASUS Noise Filter ASUS EZ DIY:
- ASUS Q-Connector
- ASUS O.C. Prole
- ASUS CrashFree BIOS 3
- ASUS EZ Flash 2
Intelligent overclocking tools:
- ASUS AI Booster utility Precision Tweaker:
- vCore: Adjustable CPU voltage at 0.0125V increment
- vDIMM: 17-step DRAM voltage control SFS (Stepless Frequency Selection):
- FSB tuning from 200MHz to 800 MHz at 1MHz increment
- Memory tuning from 667MHz to 1333MHz for DDR2
- PCI-E frequency tuning from 100MHz to 150MHz at 1 MHz increment
Overclocking protection:
- ASUS C.P.R. (CPU Parameter Recall)
1 x External Serial ATA port 1 x Coaxial S/PDIF Out port 1 x LAN (RJ-45) port 6 x USB 2.0/1.1 ports 8-channel audio ports
(continued on the next page)
xii
P5K SE specications summary
Internal connectors 3 x USB connectors support 6 additional USB ports
BIOS features 8 Mb Flash ROM, AMI BIOS, PnP, DMI 2.0, WfM 2.0, SM
Manageability WfM 2.0, DMI 2.0, WOL by PME, WOR by PME, PXE
Support CD contents Drivers
Form factor ATX form factor: 12 in x 7.6 in (30.5 cm x 19.3 cm)
*Specications are subject to change without notice.
1 x Floppy disk drive connector 1 x IDE connector 4 x Serial ATA connectors 1 x CPU / 1 x Chassis / 1 x Power fan connectors 1 x COM connector 1 x S/PDIF Out header Chassis intrusion connector Front panel audio connector CD audio in connector 24-pin ATX power connector 4-pin ATX 12V power connector System panel connector (Q-Connector)
BIOS 2.3, ACPI 2.0a, ASUS EZ Flash 2, ASUS CrashFree BIOS 3
ASUS PC Probe II ASUS Update ASUS AI Suite Anti-virus software (OEM version)
xiii
xiv
This chapter describes the motherboard features and the new technologies it supports.
Product
1
introduction
Chapter summary
1
1.1 Welcome! ...................................................................................... 1-1
1.2 Package contents .........................................................................
1.3 Special features ............................................................................
1-1
1-2
ASUS P5K SE
1.1 Welcome!
Thank you for buying an ASUS® P5K SE motherboard!
The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below.
1.2 Package contents
Check your motherboard package for the following items.
Motherboard ASUS P5K SE
Cables 2 x Serial ATA signal cable 1 x Serial ATA power cable 1 x Ultra DMA 133/100/66 cable 1 x Floppy disk drive cable
Accessories I/O shield 1 x ASUS Q-Connector Kit (USB, system panel; Retail version only)
Application CD ASUS motherboard support CD ASUS Superb Software Library CD
Documentation User guide
If any of the above items is damaged or missing, contact your retailer.
ASUS P5K SE 1-1
1.3 Special features
Supports
1.3.1 Product highlights
Green ASUS
This motherboard and its packaging comply with the European Union’s Restriction
on the use of Hazardous Substances (RoHS). This is in line with the ASUS vision
of creating environment-friendly and recyclable products/packaging to safeguard
consumers’ health while minimizing the impact on the environment.
Intel® Quad-core Processor Ready
This motherboard supports the latest Intel® Quad-core processors in the LGA775 package and Intel’s next-generation 45nm multi-core processors. It is excellent for
multi-tasking, multi-media and enthusiastic gamers with 1333/1066/800 MHz FSB.
Intel® Quad-core processor is one of the most powerful CPU in the world. See page 2-6 for details.
Intel® Core™2 Duo/ Intel® Core™2 Extreme CPU support
This motherboard supports the latest Intel® Core™2 processor in the LGA775 package and Intel’s next-generation 45nm multi-core processors. With the new Intel® Core™ microarchitecture technology and 1333/1066/800 MHz FSB, the Intel® Core™2 is one of the most powerful and energy efcient CPUs in the world. See page 2-6 for details.
Intel P35 Chipset
The Intel® P35 Express Chipset is the latest chipset designed to support the
next generation 45nm CPU and up to 8GB of dual-channel DDR2 800/677 MHz
memory architecture. It also supports 1333/1066/800 FSB (Front Side Bus), PCI Express x16 graphics and multi-core CPUs.
Native DDR2 1066 memory support
To attain top performance, ASUS engineers have successfully unleashed the true potential of DDR2 memory. While in FSB 1333 mode, ASUS’s exclusive technology offers a choice of DDR2 1066, providing great performance for 3D graphics and other memory demanding applications. See page 2-13 for details.
1-2 Chapter 1: Product Introduction
ASUS Super Memspeed Technology
To attain top performance, ASUS has managed to break through current FSB
and DRAM ratio proportions by utilizing Super Memspeed Technology–the latest
technology that provides even more precise overclocking options to unleash the
true potential of DDR2 memory. The DDR2 Mode maximizes system performance by eliminating the bottleneck when overclocking both the CPU and memory–
providing great performance for 3D graphics and other memory demanding applications. See page 2-13 for details.
Serial ATA 3.0 Gb/s technology and SATA-On-The-Go
This motherboard supports the next-generation hard drives based on the Serial
ATA (SATA) 3Gb/s storage specication, delivering enhanced scalability and
doubling the bus bandwidth for high-speed data retrieval and saves. The external SATA port located at the back I/O provides smart setup and hot-plug functions. Easily backup photos, videos and other entertainment contents to external devices. See pages 2-25, and 2-28 for details.
S/PDIF digital sound ready
This motherboard provides convenient connectivity to external home theater audio systems via coaxial and optical S/PDIF-out (SONY-PHILIPS Digital Interface) jacks.It allows to transfer digital audio without converting to analog format and keeps the best signal quality. See pages 2-25 and 2-29 for details.
High Denition Audio
Enjoy high-end sound quality on your PC! The onboard 8-channel High Denition Audio CODEC enables high-quality 192KHz/24-bit audio output, jack-sensing
feature, and multi-streaming technology that simultaneously sends different audio streams to different destinations. You can now talk to your partners on the headphone while playing multi-channel network games. See pages 2-24 and 2-25 for details.
ASUS P5K SE 1-3
1.3.2 ASUS AI Lifestyle features
ASUS Quiet Thermal Solution
ASUS Quiet Thermal solution makes system more stable and enhances the overclocking capability.
AI Gear 2
AI Gear 2 allows you to choose proles to adjust the CPU frequency and Vcore voltage to minimize system noise and power consumption. You can
change the mode in real-time in the operating system to max power saving mode and save up to 50% power when using word processing applications. See page 5-22 for details.
AI Nap
With AI Nap, the system can continue running at minimum power and noise when you are temporarily away. To wake the system and return to the OS environment, simply click the mouse or press a key. See page 5-23 for details.
Q-Fan 2
ASUS Q-Fan2 technology intelligently adjusts both CPU fan and chassis fan
speeds according to system loading to ensure quiet, cool and efcient operation.
See page 4-27 and 5-25 for details.
ASUS Crystal Sound
This feature can enhance speech-centric applications like Skype, online game, video conference and recording.
Noise Filter
This feature detects repetitive and stationary noises (non-voice signals) like computer fans, air conditioners, and other background noises then eliminates it in the incoming audio stream while recording.
1-4 Chapter 1: Product Introduction
ASUS EZ DIY
ASUS EZ DIY feature collection provides you easy ways to install computer components, update the BIOS or back up your favorite settings.
ASUS Q-Connector
ASUS Q-Connector allows you to easily connect or disconnect the chassis front panel cables to the motherboard. This unique module eliminates the trouble of connecting the system panel cables one at a time and avoiding wrong cable connections. See page 2-35 for details.
ASUS O.C. Prole
The motherboard features the ASUS O.C. Prole that allows users to
conveniently store or load multiple BIOS settings. The BIOS settings can be
stored in the CMOS or a separate le, giving users freedom to share and
distribute their favorite settings. See page 4-34 for details.
ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 allows users to restore corrupted BIOS data
from a USB ash disk containing the BIOS le. See page 4-8 for details.
ASUS EZ Flash 2
EZ Flash 2 is a user-friendly BIOS update utility. Simply press the predened
hotkey to launch the utility and update the BIOS without entering the OS. Update your BIOS easily without preparing a bootable diskette or using an
OS-based ash utility. See page 4-5 and 4-33 for details.
Smart Support CD
It provides a checklist to allow the user to see which drivers are already installed, as well as those that aren’t. When using ASUS PC Probe II, you can easily see the critical parts of the computer.
1.3.3 ASUS Stylish features
ASUS MyLogo2™
This feature allows you to convert your favorite photo into a 256-color boot logo for a more colorful and vivid image on your screen. See pages 5-8 and 5-9 for details.
ASUS P5K SE 1-5
1.3.4 ASUS Intelligent Overclocking features
AI Booster
The ASUS AI Booster allows you to overclock the CPU speed in Windows environment without the hassle of booting the BIOS. See page 5-26 for details.
Precision Tweaker
This feature allows you to ne tune the CPU/memory voltage and gradually increase the memory Front Side Bus (FSB) and PCI Express frequency at 1MHz
increment to achieve maximum system performance. See page 4-17 to 4-19 for details.
C.P.R. (CPU Parameter Recall)
The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the BIOS default settings in case the system hangs due to overclocking. When the system hangs due to overclocking, C.P.R. eliminates the need to open the system chassis and clear the RTC data. Simply shut down and reboot the system, and the BIOS automatically restores the CPU default setting for each parameter.
1-6 Chapter 1: Product Introduction
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
information
Hardware
2
Chapter summary
2
2.1 Before you proceed ..................................................................... 2-1
2.2 Motherboard overview .................................................................
2.3 Central Processing Unit (CPU) ...................................................
2.4 System memory .........................................................................
2.5 Expansion slots ..........................................................................
2.6 Jumpers ......................................................................................
2.7 Connectors .................................................................................
2-2
2-6
2-13
2-19
2-22
2-24
ASUS P5K SE
2.1 Before you proceed
P5K SE
®
P5K SE Onboard LED
SB_PWR
ON
Standby
Power
OFF
Powered
Off
Take note of the following precautions before you install motherboard components or change any motherboard settings.
Unplug the power cord from the wall socket before touching any component.
Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity.
Hold components by the edges to avoid touching the ICs on them.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.
Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.
Onboard LED
The motherboard comes with a standby power LED that lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED.
ASUS P5K SE 2-1
P5K SE
®
2.2 Motherboard overview
Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.
Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components.
2.2.1 Placement direction
When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below.
2.2.2 Screw holes
Place six (6) screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
Place this side towards the rear of the chassis
2-2 Chapter 2: Hardware information
2.2.3 Motherboard layout
PANEL
P5K SE
®
AAFP
CHASSIS
19.3cm (7.6in)
30.5cm (12.0in)
CPU_FAN
DDR2 DIMM_A1 (64 bit,240-pin module)
Super
I/O
CD
CLRTC
Intel
®
ICH9
EATXPWR
CR2032 3V
Lithium Cell
CMOS Power
Intel
®
P35
PCI1
USB1112
LAN1_USB12
KB_USB56
USB34
PCIEX16_1
PCI2
SPDIF_OUT
LGA775
USB910
SATA2
ATX12V
Marvell
88SE6111
PWR_FAN
DDR2 DIMM_A2 (64 bit,240-pin module)
PCIEX1_1
CHA_FAN
AUDIO
USB78
ESATA
COM1
BIOS
PRI_EIDE
SB_PWR
SATA4
SATA1
SATA3
SPDIF_O1
DDR2 DIMM_B1 (64 bit,240-pin module)
DDR2 DIMM_B2 (64 bit,240-pin module)
PCIEX1_2
PCIEX1_3
ALC883
AttansIc
L1
FLOPPY
USBPW9-12
USBPW1-4
USBPW78
PS2_USBPW
Refer to 2.7 Connectors for more information about rear panel connectors and internal connectors.
ASUS P5K SE 2-3
2.2.4 Layout contents
Slots Page
1. DDR2 DIMM slots 2-13
2. PCI slots
3 PCI Express x1 slot
4. PCI Express x16 slots
Jumper Page
1. Clear RTC RAM (3-pin CLRTC) 2-22
2. Keyboard power (3-pin PS2_USBPW)
3. USB device wake-up (3-pin USBPW1-4, USBPW5-8, USB9-12) 2-23
Rear panel connectors Page
1. PS/2 keyboard port (purple) 2-24
2. LAN (RJ-45) port
3. Center/Subwoofer port (orange)
4. Rear Speaker Out port (black)
5. Line In port (light blue)
6. Line Out port (lime)
7. Microphone port (pink)
8. Side Speaker Out port (gray)
9. USB 2.0 ports 1 and 2
10. External SATA port
11. USB 2.0 ports 3 and 4
12. Coaxial S/PDIF Out port
13. USB 2.0 ports 5 and 6
2-21
2-21
2-21
2-23
2-24
2-24
2-24
2-24
2-24
2-24
2-24
2-24
2-25
2-25
2-25
2-25
2-4 Chapter 2: Hardware information
Internal connectors Page
1. Floppy disk drive connector (34-1 pin FLOPPY) 2-26
2. IDE connector (40-1 pin PRI_EIDE
3. ICH9 Serial ATA connectors (7-pin SATA1-4
4. Digital audio connector (4-1 pin SPDIF_OUT) 2-29
5. USB connectors (10-1 pin USB78, USB910, USB1112
6. Optical drive audio connector (4-pin CD) 2-30
7. CPU, chassis, and power fan connectors (4-pin CPU FAN, 3-pin CHA_FAN, 3-pin PWR_FAN)
8. Serial port connector (10-1 pin COM1)
9. Chassis intrusion connector (4-1 pin CHASSIS) 2-32
10. Front panel connector (10-1 pin AAFP)
11. ATX power connectors (24-pin EATXPWR, 4-pin EATX12V)
12. System panel connector (20-8-pin PANEL
System power LED (2-pin PLED)
Hard disk drive activity LED (2-pin IDE_LED)
System warning speaker (4-pin SPEAKER)
ATX power button/soft-off button (2-pin PWRSW)
Reset button (2-pin RESET)
ASUS Q-connector (system panel) 2-35
) 2-27
) 2-28
) 2-30
2-31
2-31
2-32
2-33
)
2-34
ASUS P5K SE 2-5
2.3 Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA775 socket designed for the Intel® Core™2 Quad / Intel® Core™2 Extreme / Core™2 Duo / Pentium® Extreme / Pentium® D/ Pentium® 4 / Celeron® D processors.
Make sure that all power cables are unplugged before installing the CPU.
Connect the chassis fan cable to the CHA_FAN1 connector to ensure system stability.
Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/transit-related.
Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes
with the cap on the LGA775 socket.
The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/ incorrect removal of the PnP cap.
2-6 Chapter 2: Hardware information
2.3.1 Installing the CPU
P5K SE
®
P5K SE CPU Socket 775
To install a CPU:
1. Locate the CPU socket on the motherboard.
Before installing the CPU, make sure that the socket box is facing towards you and the load lever is on your left.
2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab.
Retention tab
Load lever
3. Lift the load lever in the direction of the arrow to a 135º angle.
ASUS P5K SE 2-7
A
PnP cap
B
This side of the socket box should face you.
To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU.
4. Lift the load plate with your thumb
and forenger to a 100º angle (A),
then push the PnP cap from the load plate window to remove (B).
Alignment key
5. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the
socket then t the socket
alignment key into the CPU notch.
The CPU ts in only one correct orientation. DO NOT force the CPU into the
socket to prevent bending the connectors on the socket and damaging the CPU!
CPU notch
Gold triangle mark
B
A
Load plate
6. Close the load plate (A), then
A
push the load lever (B) until it snaps into the retention tab.
7. If installing a dual-core CPU, connect the chassis fan cable
B
to the CHA_FAN1 connector to ensure system stability.
2-8 Chapter 2: Hardware information
2.3.2 Installing the CPU heatsink and fan
The Intel® LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance.
When you buy a boxed Intel® processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel®-certied multi-directional heatsink and fan.
®
Your Intel and requires no tool to install.
If you purchased a separate CPU heatsink and fan assembly, make sure that you have properly applied Thermal Interface Material to the CPU heatsink or CPU before you install the heatsink and fan assembly.
Make sure that you have installed the motherboard to the chassis before you install the CPU fan and heatsink assembly.
To install the CPU heatsink and fan:
1. Place the heatsink on top of the installed CPU, making sure that the four fasteners match the holes on the motherboard.
Orient the heatsink and fan assembly such that the CPU fan cable is closest to the CPU fan connector.
LGA775 heatsink and fan assembly comes in a push-pin design
Motherboard hole
Narrow end of the groove
Make sure to orient each fastener with the narrow end of the groove pointing outward. (The photo shows the groove shaded for emphasis.)
ASUS P5K SE 2-9
Fastener
2. Push down two fasteners at a time in
P5K SE
®
P5K SE CPU fan connector
CPU_FAN
GND
CPU FAN PWR
CPU FAN IN
CPU FAN PWM
a diagonal sequence to secure the heatsink and fan assembly in place.
B
A
A
A
B
B
A
B
3. Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN.
Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
2-10 Chapter 2: Hardware information
2.3.3 Uninstalling the CPU heatsink and fan
To uninstall the CPU heatsink and fan:
1. Disconnect the CPU fan cable from the connector on the motherboard.
2. Rotate each fastener counterclockwise.
3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard.
A
B
A
A
B
B
A
B
4. Carefully remove the heatsink and fan assembly from the motherboard.
ASUS P5K SE 2-11
5. Rotate each fastener clockwise to ensure correct orientation when reinstalling.
The narrow end of the groove should point outward after resetting. (The photo shows the groove shaded for emphasis.)
Narrow end of the groove
Refer to the documentation in the boxed or stand-alone CPU fan package for detailed information on CPU fan installation.
2-12 Chapter 2: Hardware information
2.4 System memory
P5K SE
®
P5K SE 240-pin DDR2 DIMM sockets
DIMM_A2
DIMM_A1
DIMM_B2
DIMM_B1
2.4.1 Overview
The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets.
The gure illustrates the location of the DDR2 DIMM sockets:
Channel Sockets
Channel A DIMM_A1 and DIMM_B1
Channel B DIMM_A2 and DIMM_B2
This chipset ofcially supports DDR2-800 MHz. With the ASUS Super
Memspeed Technology, this motherboard natively supports up to
DDR2-1066 MHz. See the table below.
FSB DDR2
1333 1066*
1333 800
1333 667
1066 1066*
1066 800
1066 667
*If you install a DDR2-1066 memory module whose SPD is DDR2-800,
make sure that you set the DRAM Frequency item in BIOS to [DDR2-1066MHz]. See section 4.4.1 Jumperfree Conguration for details.
ASUS P5K SE 2-13
2.4.2 Memory congurations
You may install 256 MB, 512 MB, 1 GB, and 2 GB unbuffered non-ECC DDR2 DIMMs into the DIMM sockets.
Recommended Memory Congurations
Mode
Single-Channel
Dual-channel (1) Populated - Populated -
Dual-channel (2) Populated Populated Populated Populated
You may install varying memory sizes in Channel A and Channel B. The
Always install DIMMs with the same CAS latency. For optimum compatibility,
If you install four 1 GB memory modules, the system may only recognize less
If you install Windows
This motherboard does not support memory modules made up of 128 Mb
Notes on memory limitations
Due to chipset limitation, this motherboard can only support up to
DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2
- - Populated -
Populated - - -
system maps the total size of the lower-sized channel for the dual-channel conguration. Any excess memory from the higher-sized channel is then
mapped for single-channel operation.
it is recommended that you obtain memory modules from the same vendor.
than 3GB because the address space is reserved for other critical functions. This limitation appears on Windows® XP/Vista 32-bit operation system which does not support Physical Address Extension (PAE).
less than 3GB is recommended.
chips.
8 GB on the operating systems listed below. You may install a maximum of 2 GB DIMMs on each slot.
Sockets
®
XP/Vista 32-bit operation system, a total memory of
64-bit
Windows® XP Professional x64 Edition
Windows® Vista x64 Edition
Some old-version DDR2-800 DIMMs may not match Intel®’s On-Die-Termination (ODT) requirement and will automatically downgrade to run at DDR2-667. If this happens, contact your memory vendor to check the ODT value.
Due to chipset limitation, DDR2-800 with CL=4 will be downgraded to run at DDR2-667 by default setting. If you want to operate with lower latency, adjust the memory timing manually.
2-14 Chapter 2: Hardware information
P5K SE Motherboard Qualied Vendors Lists (QVL) DDR2-1066 MHz capability
Size Vendor
512 OCZ DS OCZ2P10002GK / PC2 8000 / 1G EL Dual CH / Platinum
512 Crucial SS BL646AA1005.8FD / CL111R5W6-65183
512 Kingston SS KHX8500D2 / 512 / 9905315 - 028.AOOLF / 2297056 2.2V
1024 Kingston DS KHX8000D2 / 1G / 9905316 - 028.AOOLF / 2310576 2.2V
1024 CORSAIR DS CM2X1024-8500C5D 1024MB / XMS8505v1.2 /
1024 CORSAIR DS CM21024-8500-C5 / XMS8505v1.1 / 0616126-12
1024 OCZ DS OCZ2TA1000VX22GK / PC2 8000 / 1GB Dual CH / Titanium
1024 Kingston DS KHX8500D2K2 / 2GN / 9905316 - 071.AOOLF K2 /
1024 CORSAIR DS CM2X1024 - 9136C5D / XMS9105V1.1
SS/
DS
Part No.
XTC
0648081-1
Alpha VX2
2733866 2.2V
DIMM support
A* B* C*
If you install a DDR2-1066 memory module whose SPD is DDR2-800, make sure that you set the DRAM Frequency item in BIOS to [DDR2-1066MHz]. See section 4.4.1 Jumperfree Conguration for details.
A*: Supports one module inserted in any slot as Single-channel memory
conguration.
B*: Supports one pair of modules inserted into either the yellow slots or the
black slots as one pair of Dual-channel memory conguration.
C*: Supports 4 modules inserted into both the yellow and black slots as two
pairs of Dual-channel memory conguration.
Visit the ASUS website for the latest DDR2-1066/800/667MHz QVL.
ASUS P5K SE 2-15
P5K SE Motherboard Qualied Vendors Lists (QVL) DDR2-800 MHz capability
Size Vendor Chip No. CL
512MB KINGSTON K4T51083QC 5 SEC SS KVR800D2N5/512
1024MB KINGSTON Heat-Sink Package 4-4-4-12 N/A DS KHX6400D2LL/1G
1024MB KINGSTON Heat-Sink Package 4-4-4-12 N/A SS KHX6400D2LLK2/1GN
1024MB KINGSTON V59C1512804QBF25 N/A N/A DS KVR800D2N5/1G
256MB Qimonda HYB18T512160BF-25F 5-5-5 INFINEON SS HYS64T32000HU-25F-B
512MB Qimonda HYB18T512800BF25F 5-5-5 N/A SS HYS64T64000HU-25F-B
1024MB Qimonda HYB18T512800BF25F 5-5-5 N/A DS HYS64T128020HU-25F-B
512MB SAMSUNG EDD339XX 5-5-5 N/A SS M378T6553CZ3-CE7
256MB SAMSUNG K4T51163QC-ZCE7 5-5-5 SAMSUNG SS M378T3354CZ3-CE7
512MB SAMSUNG ZCE7K4T51083QC 5-5-5 SEC SS M378T6553CZ3-CE7
512MB Hynix HY5PS12821CFP-S5 5-5-5 Hynix SS HYMP564U64CP8-S5
512MB MICRON D9GKX N/A N/A SS MT8HTF6464AY-80ED4
1024MB MICRON D9GKX N/A N/A DS MT16HTF12864AY-80ED4
1024MB CORSAIR Heat-Sink Package 4 N/A DS CM2X1024-6400C4
512MB Crucial Heat-Sink Package 4 N/A SS BL6464AA804.8FD
1024MB Crucial Heat-Sink Package 4 N/A DS BL12864AA804.16FD
1024MB Crucial Heat-Sink Package 4 N/A DS BL12864AL804.16FD3
1024MB Crucial Heat-Sink Package 4 N/A DS BL12864AA804.16FD3
512MB Apacer Heat-Sink Package 5 N/A DS AHU512E800C5K1C
1024MB Apacer Heat-Sink Package 5 N/A DS AHU01GE800C5K1C
512MB A-DATA AD29608A8A-25EG N/A N/A SS M2OAD6G3H3160G1E53
1024MB A-DATA AD26908A8A-25EG N/A N/A DS M2OAD6G3I4170I1E58
512MB KINGMAX KKA8FEIBF-HJK-25A N/A KINGMAX SS KLDC28F-A8KI5
1024MB KINGMAX KKA8FEIBF-HJK-25A N/A KINGMAX DS KLDD48F-ABKI5
512MB Transcend HY5PS12821CFP-S5 N/A Hynix SS TS64MLQ64V8J
1024MB Transcend HY5PS12821CFP-S5 N/A Hynix DS TS128MLQ64V8J
512MB Super
Talent
512MB NANYA NT5TU64M8BE-25C 5 NANYA SS NT512T64U880BY-25C
1024MB NANYA NT5TU64M8BE-25C 5 NANYA DS NT1GT64U8HB0BY-25C
512MB PSC A3R12E3HEF641B9A05 5 PSC SS AL6E8E63B8E1K
1024MB PSC A3R12E3HEF641B9A05 5 PSC DS AL7E8E63B-8E1K
Heat-Sink Package N/A N/A SS T800UA12C4
Chip Brand
SS/
Part No.
DS
DIMM support
A* B* C*
2-16 Chapter 2: Hardware information
P5K SE Motherboard Qualied Vendors Lists (QVL) DDR2-667MHz capability
Size Vendor Chip No. CL
512MB SAMSUNG ZCE6K4T51083QC 5 SEC SS M378T6553CZ0-CE6
512MB SAMSUNG K4T51083QC 5 SEC SS M378T6553CZ3-CE6
1024MB SAMSUNG ZCE6K4T51083QC 5 SEC DS M378T2953CZ3-CE6
256MB SAMSUNG K4T51163QE-ZCE6 5 SAMSUNG SS M378T3354EZ3-CE6
512MB SAMSUNG K4T51083QE 5 SAMSUNG DS M378T6553EZS-CE6
1024MB SAMSUNG K4T51083QE 5 SAMSUNG DS M378T2953EZ3-CE6
256MB Hynix HY5PS121621CFP-Y5 5 Hynix SS HYMP532U64CP6-Y5
1024MB Hynix HY5PS12821CFP-Y5 5 Hynix DS HYMP512U64CP8-Y5
256MB CORSAIR MIII00605 N/A N/A SS VS256MB667D2
2048MB NANYA NT5TU128M8BJ-3C 5 NANYA DS NT2GT64U8HB0JY-3C
512MB NANYA NT5TU64M8BE-3C 5 NANYA SS NT512T64U88B0BY-3C
512MB PSC A3R12E3GEF637BLC5N 5 PSC SS AL6E8E63B-6E1K
1024MB PSC A3R12E3GEF637BLC5N 5 PSC DS AL7E8E63B-6E1K
Chip Brand
SS/
Part No.
DS
DIMM support
A* B* C*
ASUS P5K SE 2-17
2.4.3 Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components.
To install a DIMM:
1. Unlock a DIMM socket by pressing the retaining clips outward.
2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket.
3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.
A DDR2 DIMM is keyed with a notch so that it ts in only one direction. Do
not force a DIMM into a socket to avoid damaging the DIMM.
The DDR2 DIMM sockets do not support DDR DIMMs. Do not install DDR DIMMs to the DDR2 DIMM sockets.
2.4.4 Removing a DIMM
To remove a DIMM:
1. Simultaneously press the retaining clips outward to unlock the DIMM.
2
3
1
DDR2 DIMM notch
1
Unlocked retaining clip
2
Support the DIMM lightly with
your ngers when pressing the
retaining clips. The DIMM might
get damaged when it ips out with
extra force.
1
DDR2 DIMM notch
1
2. Remove the DIMM from the socket.
2-18 Chapter 2: Hardware information
2.5 Expansion slots
In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.
2.5.1 Installing an expansion card
To install an expansion card:
1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card.
2. Remove the system unit cover (if your motherboard is already installed in a chassis).
3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use.
4. Align the card connector with the slot and press rmly until the card is
completely seated on the slot.
5. Secure the card to the chassis with the screw you removed earlier.
6. Replace the system cover.
2.5.2 Conguring an expansion card
After installing the expansion card, congure it by adjusting the software settings.
1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 4 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page.
3. Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share
IRQ” or that the cards do not need IRQ assignments. Otherwise, conicts will
arise between the two PCI groups, making the system unstable and the card inoperable. Refer to the table on the next page for details.
ASUS P5K SE 2-19
2.5.3 Interrupt assignments
IRQ Standard function
0 System timer 1 Keyboard controller 2
Re-direct to IRQ#9 3 IRQ holder for PCI steering* 4 Communications port (COM1)* 5 IRQ holder for PCI steering* 6 Floppy disk controller 8 System CMOS/Real Time Clock 9 Microsoft ACPI-Compliant System
10 IRQ holder for PCI steering* 11 IRQ holder for PCI steering* 13 Numeric data processor 14 Intel(R) ICH9 Family SMbus Controller
* These IRQs are usually available for PCI devices.
IRQ assignments for this motherboard
A B C D E F G H
PCI slot 1 shared – PCI slot 2 shared – LAN (L1) shared – SATA (Marvell) shared – PCIE x16 shared – PCIE x1_1 shared – PCIE x1_2 shared – PCIE x1_3 shared – USB controller 1 shared – USB controller 2 shared – USB controller 3 shared – USB controller 4 shared – USB controller 5 shared – USB controller 6 shared – USB 2.0 controller 1 shared USB 2.0 controller 2 shared – SATA controller 1 shared – SATA controller 2 shared – Azalia 883 shared
2-20 Chapter 2: Hardware information
2.5.4 PCI slots
The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI
specications. The gure shows a LAN
card installed on a PCI slot.
2.5.5 PCI Express x1 slots
This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express
specications. The following gure
shows a network card installed on the PCI Express x1 slot.
2.5.6 PCI Express x16 slot
This motherboard supports one PCI Express x16 graphics card that complies
with the PCI Express specications.
The gure shows a graphics card
installed on the PCI Express x16 slot.
ASUS P5K SE 2-21
2.6 Jumpers
P5K SE
®
1 2 2 3
P5K SE Clear RTC RAM
CLRTC
Normal
(Default)
Clear RTC
1. Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2.
4. Reinstall the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure!
You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the C.P.R. (CPU Parameter Recall) feature. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values.
Due to the chipset limitation, AC power off is required prior using C.P.R. function. You must turn off and on the power supply or unplug and plug the power cord before reboot the system.
2-22 Chapter 2: Hardware information
P5K SE
®
3
2
21
P5K SE Keyboard power
+5V
(Default)
+5VSB
PS2_USBPW
2. Keyboard power (3-pin PS2_USBPW)
P5K SE
®
3
2
21
P5K SE USB device wake up
USBPW1-4
USBPW78
+5V
(Default)
+5VSB
+5V
(Default)
+5VSB
USBPW9-12
2 1
2 1
This jumper allows you to enable or disable the keyboard and USB port 5-6
wake-up feature. When you set this jumper to pins 2-3 (+5VSB), you can wake up the computer by pressing a key on the keyboard (the default is the Space Bar) or using a USB device. This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS. The USBPWR5-6 jumper is for the internal USB connectors that you can connect to additional USB ports.
3. USB device wake-up (3-pin USBPW1-4, USBPW5-8, USB9-12)
Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode).
The USBPWR1-4 and USBPWR78 jumpers are for the rear USB ports. The USBPWR9-12 jumper is for the internal USB connectors that you can connect to additional USB ports.
The USB device wake-up feature requires a power supply that can
The total current consumed must NOT exceed the power supply
ASUS P5K SE 2-23
provide 500mA on the +5VSB lead for each USB port; otherwise, the system would not power up.
capability (+5VSB) whether under normal condition or in sleep mode.
2.7 Connectors
1012 78
5 641 2
913
3
11
2.7.1 Rear panel connectors
1. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
2. LAN (RJ-45) port.
Gigabit connection to a Local Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications.
3. Center/Subwoofer port (orange).
speakers.
LAN port LED indications
Activity/Link Speed LED Status Description Status Description
OFF No link OFF 10 Mbps connection
ORANGE Linked ORANGE 100 Mbps connection
BLINKING Data activity GREEN 1 Gbps connection
Supported by Gigabit LAN controller, this port allows
This port connects the center/subwoofer
ACT/LINK
LED
LAN port
SPEED
LED
4. Rear Speaker Out port (black).
This port connects the rear speakers in a
4-channel, 6-channel, or 8-channel audio conguration.
5. Line In port (light blue).
This port connects the tape, CD, DVD player, or
other audio sources.
6. Line Out port (lime).
This port connects a headphone or a speaker. In
4-channel, 6-channel, and 8-channel conguration, the function of this port
becomes Front Speaker Out.
7. Microphone port (pink).
8. Side Speaker Out port (gray).
This port connects a microphone.
This port connects the side speakers in an
8-channel audio conguration.
9. USB 2.0 ports 1 and 2.
are available for connecting USB 2.0 devices.
Refer to the audio conguration table on the next page for the function of the audio ports in 2, 4, 6, or 8-channel conguration.
2-24 Chapter 2: Hardware information
These two 4-pin Universal Serial Bus (USB) ports
Audio 2, 4, 6, or 8-channel conguration
Port
Light Blue Line In Line In Line In Line In
Lime Line Out Front Speaker Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Mic In Mic In
Orange Center/Subwoofer Center/Subwoofer
Black Rear Speaker Out Rear Speaker Ou Rear Speaker Out
Gray Side Speaker Out
10 External SATA port. This port connects an external Serial ATA hard disk
Headset 2-channel
4-channel 6-channel 8-channel
drive.
The external SATA port supports external Serial ATA 3.0 Gb/s devices. Longer cables support higher power requirements to deliver signal up to two meters away, and enables improved hot­swap function.
DO NOT insert a different connector to this port.
11. USB 2.0 ports 3 and 4.
These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
12. Coaxial S/PDIF Out port.
This port connects an external audio output device
via a coaxial S/PDIF cable.
13. USB 2.0 ports 5 and 6.
These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
ASUS P5K SE 2-25
2.7.2 Internal connectors
P5K SE
®
P5K SE Floppy disk drive connector
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
FLOPPY
1. Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided oppy disk drive (FDD) signal cable. Insert
one end of the cable to this connector, then connect the other end to the
signal connector at the back of the oppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5.
2-26 Chapter 2: Hardware information
2. IDE connector (40-1 pin PRI_EIDE)
P5K SE
®
P5K SE IDE connector
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PRI_EIDE
PIN 1
The onboard IDE connector is for the Ultra DMA 133/100/66 signal cable. There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE
connector, then select one of the following modes to congure your device.
Drive jumper setting Mode of
Cable connector
device(s)
Single device Cable-Select or Master - Black
Two devices Cable-Select Master
Black
Slave Gray
Master Master Black or gray
Slave Slave
Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.
Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.
If any device jumper is set as “Cable-Select,” make sure all other device jumpers have the same setting.
ASUS P5K SE 2-27
3. ICH9 Serial ATA connectors (7-pin SATA1-4)
P5K SE
®
P5K SE SATA connectors
SATA3
SATA1
SATA4
SATA2
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives.
When using the connectors in Standard IDE mode, connect the primary (boot) hard disk drive to the SATA1/2 connector. Refer to the table below for the recommended SATA hard disk drive connections.
Connect the right-angle side
right angle side
of SATA signal cable to SATA device. Or you may connect the right-angle side of SATA cable to the onboard SATA port to avoid
mechanical conict with huge
graphics cards.
2-28 Chapter 2: Hardware information
4. Digital audio connector (4-1 pin SPDIF_OUT)
P5K SE
®
P5K SE Digital audio connector
+5V
SPDIFOUT
GND
SPDIF_OUT
This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis.
The S/PDIF module is purchased separately.
ASUS P5K SE 2-29
5. USB connectors (10-1 pin USB78, USB 910, USB1112)
P5K SE
®
USB+5V
USB_P8-
USB_P8+
GND
NC
USB+5V
USB_P7-
USB_P7+
GND
P5K SE USB 2.0 connectors
USB910
USB+5V
USB_P6-
USB_P6+
GND
NC
USB+5V
USB_P5-
USB_P5+
GND
USB1112
USB+5V
USB_P12-
USB_P12+
GND
NC
USB+5V
USB_P11-
USB_P11+
GND
USB78
P5K SE
®
P5K SE Internal audio connector
CD
Right Audio Channel
Left Audio Channel
Ground
Ground
These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0
specication that supports up to 480 Mbps connection speed.
Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!
You can connect the front panel USB cable to the ASUS Q-Connector (USB,
blue) rst, and then install the Q-Connector (USB) to the USB connector
onboard if your chassis supports front panel USB ports.
The USB module cable is purchased separately.
6. Optical drive audio connector (4-pin CD)
These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card.
2-30 Chapter 2: Hardware information
7. CPU, chassis, and power fan connectors
P5K SE
®
P5K SE Fan connectors
CPU_FAN
GND
CPU FAN PWR
CPU FAN IN
CPU FAN PWM
GND
Rotation
+12V
CHA_FANPWR_FAN
GND
Rotation
+12V
P5K SE
®
P5K SE COM port connector
PIN 1
COM1
(4-pin CPU_FAN, 3-pin CHA_FAN, 3-pin PWR_FAN)
The fan connectors support cooling fans of 350 mA~2000 mA (24 W max.) or a total of 1 A~7 A (84 W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufcient air ow inside the system may damage the motherboard components. These are
not jumpers! Do not place jumper caps on the fan connectors!
Only the CPU_FAN and CHA_FAN connector support the ASUS Q-FAN 2 feature.
8. Serial port connector (10-1 pin COM1)
This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis.
ASUS P5K SE 2-31
The serial port module is purchased separately.
9. Chassis intrusion connector (4-1 pin CHASSIS)
P5K SE
®
P5K SE Chassis intrusion connector
CHASSIS
+5VSB_MB
Chassis Signal
GND
(Default)
P5K SE
®
P5K SE Analog front panel connector
AAFP
Legacy AC ‘97 audio pin definition
SENSE2_RETUR
PORT1 L
PORT2 R
PORT2 L
SENSE1_RETUR
SENSE_SEND
PORT1 RPRESENCE#
GND
NC
MIC2
Line out_R
Line out_L
NC
NC
MICPWRNC
AGND
HD Audio-compliant pin definition
This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event.
By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature.
10. Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.
We recommend that you connect a high-denition front panel audio module
to this connector to avail of the motherboard’s high-denition audio capability.
If you want to connect a high-denition front panel audio module to this
connector, set the Front Panel Type item in the BIOS setup to [HD Audio]; if you want to connect an AC'97 front panel audio module to this connector, set the item to [AC'97]. By default, this connector is set to [HD Audio]. See section 4.4.5 Onboard Devices Conguration for details.
2-32 Chapter 2: Hardware information
11. ATX power connectors (24-pin EATXPWR, 4-pin EATX12V)
P5K SE
®
P5K SE ATX power connectors
EATXPWR
+3 Volts
+3 Volts
Ground
+5 Volts
+5 Volts
Ground
Ground
Power OK
+5V Standby
+12 Volts
-5 Volts
+5 Volts
+3 Volts
-12 Volts
Ground
Ground Ground PSON#
Ground
+5 Volts
+12 Volts
+3 Volts
+5 Volts
Ground
ATX12V
+12V DC GND
+12V DC GND
These connectors are for ATX power supply plugs. The power supply plugs
are designed to t these connectors in only one orientation. Find the proper orientation and push down rmly until the connectors completely t.
For a fully congured system, we recommend that you use a power supply
unit (PSU) that complies with ATX 12 V Specication 2.0 (or later version)
and provides a minimum power of 400 W.
Do not forget to connect the 4-pin EATX12V power plug; otherwise, the
system will not boot.
Use of a PSU with a higher power output is recommended when
conguring a system with more power-consuming devices. The system
may become unstable or may not boot up if the power is inadequate.
• The ATX 12 V Specication 2.0-compliant (400W) PSU has been tested
to support the motherboard power requirements with the following conguration:
CPU: Intel® Pentium® Extreme 3.73GHz Memory: 512 MB DDR2 (x4) Graphics card: ASUS EAX1900XT Parallel ATA device: IDE hard disk drive Serial ATA device: SATA hard disk drive (x2) Optical drive: DVD-RW
ASUS P5K SE 2-33
12. System panel connector (20-8 pin PANEL)
P5K SE
®
P5K SE System panel connector
* Requires an ATX power supply.
PANEL
PLED-
PWR
+5V
Speaker
Ground
RESET
Ground
Reset
Ground
Ground
PWRSW
PLED+
IDE_LED-
IDE_LED+
IDE_LED
PLED SPEAKER
This connector supports several chassis-mounted functions.
System power LED (2-pin PLED)
This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
Hard disk drive activity LED (2-pin IDE_LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity
LED cable to this connector. The IDE LED lights up or ashes when data is
read from or written to the HDD.
System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings.
ATX power button/soft-off button (2-pin PWRSW)
This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF.
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power.
2-34 Chapter 2: Hardware information
Q-Connector (system panel)
You can use ASUS Q-Connector to connect / disconnect chassis front panel
cables by only a few steps. Directions below shows how to install ASUS Q-Connector.
Step1.
Connect correct front panel to ASUS
Q-Connector rst. You can refer to the
marking on Q-Connector itself to know the
detail pin denition.
Step2.
Properly install the ASUS Q-Connector to the
System panel connctor.
Step3.
Front panel functions are enabled.
ASUS P5K SE 2-35
2-36 Chapter 2: Hardware information
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Powering up
3
Chapter summary
3
3.1 Starting up for the rst time ........................................................ 3-1
3.2 Turning off the computer .............................................................
3-2
ASUS P5K SE
3.1 Starting up for the rst time
1. After making all the connections, replace the system case cover.
2. Be sure that all switches are off.
3. Connect the power cord to the power connector at the back of the system chassis.
4. Connect the power cord to a power outlet that is equipped with a surge protector.
5. Turn on the devices in the following order:
a. Monitor
b. External SCSI devices (starting with the last device on the chain)
c. System power
6. After applying power, the system power LED on the system front panel case lights up. For systems with ATX power supplies, the system LED lights up when you press the ATX power button. If your monitor complies with “green” standards or if it has a “power standby” feature, the monitor LED may light up or switch between orange and green after the system LED turns on.
The system then runs the power-on self tests or POST. While the tests are
running, the BIOS beeps (see BIOS beep codes table below) or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turned on the power, the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance.
AMI BIOS beep codes
BIOS Beep Description
One short beep VGA detected
One continuous beep followed by two short beeps then a pause (repeated)
One continuous beep followed by three short beeps
One continuous beep followed by four short beeps
Quick boot set to disabled No keyboard detected
No memory detected
No VGA detected
Hardware component failure
7. At power on, hold down the <Delete> key to enter the BIOS Setup. Follow the instructions in Chapter 4.
ASUS P5K SE
3-1
3.2 Turning off the computer
3.2.1 Using the OS shut down function
If you are using Windows® XP:
1. Click the
2. Click the
3. The power supply should turn off after Windows
button then select
Start
Turn Off
button to shut down the computer.
Turn Off Computer
®
shuts down.
.
If you are using Windows® Vista:
1. Click the
2. The power supply should turn off after Windows
Start button then select ShutDown.
®
shuts down.
3.2.2 Using the dual function power switch
While the system is ON, pressing the power switch for less than four seconds puts the system to sleep mode or to soft-off mode, depending on the BIOS setting. Pressing the power switch for more than four seconds lets the system enter the soft-off mode regardless of the BIOS setting. Refer to section “4.5 Power Menu” for details.
3-2
Chapter 3: Powering up
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
BIOS setup
4
Chapter summary
4
4.1 Managing and updating your BIOS ............................................ 4-1
4.2 BIOS setup program ....................................................................
4.3 Main menu ..................................................................................
4.4 Advanced menu .........................................................................
4.5 Power menu ................................................................................
4.6 Boot menu ..................................................................................
4.7 Tools menu .................................................................................
4.8 Exit menu .................................................................................... 4-35
4-9
4-12
4-16
4-25
4-29
4-33
ASUS P5K SE
4.1 Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup.
1.
ASUS Update (Updates the BIOS in Windows® environment.)
ASUS EZ Flash 2 (Updates the BIOS using a oppy disk or USB ash disk.)
2.
ASUS AFUDOS (Updates the BIOS using a bootable oppy disk.)
3.
ASUS CrashFree BIOS 3 (Updates the BIOS using a bootable oppy disk,
4.
USB ash disk or the motherboard support CD when the BIOS le fails or
gets corrupted.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS le to a bootable oppy disk or USB ash disk in case you need to restore the BIOS in the future. Copy the
original motherboard BIOS using the ASUS Update or AFUDOS utilities.
4.1.1 ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment. The ASUS Update utility allows you to:
Save the current BIOS le
Download the latest BIOS le from the Internet
Update the BIOS from an updated BIOS le
Update the BIOS directly from the Internet, and
View the BIOS version information.
This utility is available in the support CD that comes with the motherboard package.
ASUS Update requires an Internet connection either through a network or an Internet Service Provider (ISP).
Installing ASUS Update
To install ASUS Update:
1. Place the support CD in the optical drive. The Drivers menu appears.
2. Click the
3. The ASUS Update utility is copied to your system.
ASUS P5K SE 4-1
Utilities tab, then click Install ASUS Update.
Quit all Windows® applications before you update the BIOS using this utility.
Updating the BIOS through the Internet
To update the BIOS through the Internet:
1. Launch the ASUS Update utility from the Windows
> Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears.
®
desktop by clicking Start
2. Select Update BIOS from the
Internet option from the drop-down menu, then click Next.
4-2 Chapter 4: BIOS setup
3. Select the ASUS FTP site nearest
you to avoid network trafc, or
click Auto Select. Click Next.
4. From the FTP site, select the BIOS version that you wish to download. Click Next.
5. Follow the screen instructions to complete the update process.
The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features.
Updating the BIOS through a BIOS le
To update the BIOS through a BIOS le:
1. Launch the ASUS Update utility from the Windows > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears.
2. Select Update BIOS from a le
option from the drop-down menu, then click Next.
®
desktop by clicking Start
3. Locate the BIOS le from the Open
window, then click Open.
4. Follow the screen instructions to
P5KSE.rom
complete the update process.
P5KSE
ASUS P5K SE 4-3
4.1.2 Creating a bootable oppy disk
1. Do either one of the following to create a bootable oppy disk.
DOS environment
a. Insert a 1.44MB oppy disk into the drive.
format
b. At the DOS prompt, type
Windows® XP environment
a. Insert a 1.44 MB oppy disk to the oppy disk drive.
b. Click
c. Select the 3 1/2 Floppy Drive icon.
d. Click File from the menu, then select
e. Select
2. Copy the original or the latest motherboard BIOS le to the bootable oppy
disk.
Start from the Windows® desktop, then select My Computer.
Disk window appears.
Create an MS-DOS startup disk from the format options eld,
then click Start.
A:/S then press <Enter>.
Format. A Format 3 1/2 Floppy
4-4 Chapter 4: BIOS setup
4.1.3 ASUS EZ Flash 2 utility
The ASUS EZ Flash 2 feature allows you to update the BIOS without having to go
through the long process of booting from a oppy disk and using a DOS-based
utility. The EZ Flash 2 utility is built-in the BIOS chip so it is accessible by pressing <Alt> + <F2> during the Power-On Self Tests (POST).
To update the BIOS using EZ Flash 2:
1. Visit the ASUS website (www.asus.com) to download the latest BIOS le for
the motherboard.
2. Save the BIOS le to a oppy disk or a USB ash disk, then restart the
system.
3. You can launch the EZ Flash 2 by two methods.
Insert the oppy disk / USB ash disk that contains the BIOS le to the
(1)
oppy disk drive or the USB port.
Press <Alt> + <F2> during POST to display the following.
ASUSTek EZ Flash 2 BIOS ROM Utility V3.05
FLASH TYPE: WINBOND W25X80
Current ROM
BOARD: P5K SE VER: 0110 DATE: 05/07/07
PATH: C:\
A:
C:
Update ROM
BOARD: Unknown VER: Unknown DATE: Unknown
Note
[Enter] Select or Load [B] Backup [ESC] Exit [Tab] Switch [Up/Down/Home/End] Move
(2) Enter BIOS setup program. Go to the
Tools menu to select EZ Flash2
and press <Enter> to enable it.
You can switch between drives by pressing <Tab> before the correct le
is found. Then press <Enter>.
4. When the correct BIOS le is found, EZ Flash 2 performs the BIOS update
process and automatically reboots the system when done.
This function can support devices such as USB ash disk, or oppy disk
with
FAT 32/16
Do not shut down or reset the system while updating the BIOS to prevent system boot failure!
ASUS P5K SE 4-5
format and single partition only.
4.1.4 AFUDOS utility
The AFUDOS utility allows you to update the BIOS le in DOS environment using a bootable oppy disk with the updated BIOS le. This utility also allows you to copy the current BIOS le that you can use as backup when the BIOS fails or gets
corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS le using the AFUDOS utility:
Make sure that the oppy disk is not write-protected and has at least 1024KB free space to save the le.
The succeeding BIOS screens are for reference only. The actual BIOS screen displays may not be same as shown.
1. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to
the bootable oppy disk you created earlier.
2. Boot the system in DOS mode, then at the prompt type:
afudos /o[lename]
where the [lename] is any user-assigned lename not more than eight alphanumeric characters for the main lename and three alphanumeric
characters for the extension name.
A:\>afudos /oOLDBIOS1.rom
Main lename Extension name
3. Press <Enter>. The utility copies the current BIOS le to the oppy disk.
A:\>afudos /oOLDBIOS1.rom
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading ash ..... done
Write to le...... ok
A:\>
The utility returns to the DOS prompt after copying the current BIOS le.
Updating the BIOS le
To update the BIOS le using the AFUDOS utility:
1. Visit the ASUS website (www.asus.com) and download the latest BIOS le for the motherboard. Save the BIOS le to a bootable oppy disk.
4-6 Chapter 4: BIOS setup
Write the BIOS lename on a piece of paper. You need to type the exact BIOS lename at the DOS prompt.
2. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to
the bootable oppy disk you created earlier.
3. Boot the system in DOS mode, then at the prompt type:
afudos /i[lename]
where [lename] is the latest or the original BIOS le on the bootable oppy
disk.
A:\>afudos /iP5KSE.ROM
4. The utility veries the le and starts updating the BIOS.
A:\>afudos /iP5KSE.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during ash BIOS
Reading le ....... done
Reading ash ...... done
Advance Check ......
Erasing ash ...... done
Writing ash ...... 0x0008CC00 (9%)
Do not shut down or reset the system while updating the BIOS to prevent system boot failure!
5. The utility returns to the DOS prompt after the BIOS update process is completed. Reboot the system from the hard disk drive.
A:\>afudos /iP5KSE.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during ash BIOS
Reading le ....... done
Reading ash ...... done
Advance Check ......
Erasing ash ...... done
Writing ash ...... done
Verifying ash .... done
Please restart your computer
A:\>
ASUS P5K SE 4-7
4.1.5 ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore
the BIOS le when it fails or gets corrupted during the updating process. You can update a corrupted BIOS le using the motherboard support CD or a USB ash disk that contains the updated BIOS le.
Prepare the motherboard support CD, the oppy disk or the USB ash disk
containing the updated motherboard BIOS before using this utility.
For the P5K SE motherboard, this utility will function when you use a PATA optical drive.
Always connect the SATA cable to the SATA1 / SATA 2 connector;
otherwise, the utility will not function.
Recovering the BIOS from the support CD
To recover the BIOS from the support CD:
1. Turn on the system.
2. Insert the motherboard support CD to the optical drive.
3. The utility displays the following message and automatically checks the CD
for the BIOS le.
Bad BIOS checksum. Starting BIOS recovery...
Checking for oppy...
When found, the utility reads the BIOS le and starts ashing the corrupted
BIOS le.
Bad BIOS checksum. Starting BIOS recovery...
Checking for oppy...
Floppy found!
Reading le “P5KSE.ROM”. Completed. Start ashing...
4. Restart the system after the utility completes the updating process.
Recovering the BIOS from a USB ash disk
To recover the BIOS from a USB ash disk:
1. Insert a USB ash disk that contains BIOS le to the USB port.
2. Turn on the system.
3. The utility will automatically checks the devices for the BIOS le When found, the utility reads the BIOS le and starts ashing the corrupted BIOS le.
4. Restart the system after the utility completes the updating process.
Only the USB ash disk with FAT 32/16 format and single partition can support ASUS CrashFree BIOS 3. The device size should be smaller than
8GB.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure!
4-8 Chapter 4: BIOS setup
4.2 BIOS setup program
This motherboard supports a programmable Serial Peripheral Interface (SPI) chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard, reconguring your system, or prompted to “Run Setup.” This section explains how to congure
your system using this utility.
Even if you are not prompted to use the Setup program, you can change the
conguration of your computer in the future. For example, you can enable the
security password feature or change the power management settings. This
requires you to recongure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the
SPI chip.
The SPI chip on the motherboard stores the Setup utility. When you start up the computer, the system provides you with the opportunity to run this program. Press
<Del> during the Power-On Self-Test (POST) to enter the Setup utility; otherwise,
POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing <Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis. You can also restart by turning the system off and then back on. Do this last option only if
the rst two failed.
The Setup program is designed to make it as easy to use as possible. Being a menu-driven program, it lets you scroll through the various sub-menus and make your selections from the available options using the navigation keys.
The default BIOS settings for this motherboard apply for most conditions to ensure optimum performance. If the system becomes unstable after changing any BIOS settings, load the default settings to ensure system compatibility and stability. Select the Load Setups Default item under the Exit Menu. See section 4.8 Exit Menu.
The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.
Visit the ASUS website (www.asus.com) to download the latest BIOS le for
this motherboard.
ASUS P5K SE 4-9
4.2.1 BIOS menu screen
Menu bar
Main Advanced Power Boot Tools Exit
System Time [10:55:25] System Date [Fri 05/07/2007] Legacy Diskette A [1.44M, 3.5 in]
SATA 1 [WDC WD800JD-00LSA0] SATA 2 [Not Detected] SATA 3 [Not Detected] SATA 4 [Not Detected]
SATA Coniguration System Information
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Sub-menu items
Conguration eldsMenu items
BIOS SETUP UTILITY
General help
Use [ENTER], [TAB] or [SHIFT-TAB] to select
a eld.
Use [+] or [-] to
congure system Time.
Select Screen
Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit
Navigation keys
4.2.2 Menu bar
The menu bar on top of the screen has the following main items:
Main For changing the basic system conguration
Advanced For changing the advanced system settings
Power For changing the advanced power management (APM)
conguration
Boot For changing the system boot conguration
Tools For Conguring options for special functions
Exit For selecting the exit options and loading default settings.
To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted.
4.2.3 Navigation keys
At the bottom right corner of a menu screen are the navigation keys for that particular menu. Use the navigation keys to select items in the menu and change the settings.
Some of the navigation keys differ from one screen to another.
4-10 Chapter 4: BIOS setup
4.2.4 Menu items
The highlighted item on the menu bar
displays the specic items for that
menu. For example, selecting Main shows the Main menu items.
The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items.
System Time [06:22:54] System Date [Fri 03/09/2007] Legacy Diskette A [1.44M, 3.5 in]
SATA 1 [Not Detected] SATA 2 [Not Detected] SATA 3 [Not Detected] SATA 4 [Not Detected]
SATA Conguration
System Information
Main menu items
Use [ENTER], [TAB], or [SHIFT-TAB] to
select a eld.
Use [+] or [-] to
congure system
Time.
4.2.5 Sub-menu items
A solid triangle before each item on any menu screen means that the iteam has a sub-menu. To display the sub-menu, select the item and press <Enter>.
4.2.6 Conguration elds
These elds show the values for the menu items. If an item is user- congurable, you can change the value of the eld opposite the item. You cannot select an item that is not user-congurable.
A congurable eld is enclosed in brackets, and is highlighted when selected. To change the value of a eld, select it then press <Enter> to display a list of options.
Refer to “4.2.7 Pop-up window.”
4.2.7 Pop-up window
Select a menu item then press <Enter> to display a pop-up window with the
conguration options for that item.
4.2.8 Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not t on the screen. Press the Up/Down arrow keys or <Page Up> /<Page Down> keys to display the other items on the screen.
4.2.9 General help
At the top right corner of the menu screen is a brief description of the selected item.
ASUS P5K SE 4-11
Pop-up window
Scroll bar
4.3 Main menu
When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information.
Refer to section 4.2.1 BIOS menu screen for information on the menu screen items and how to navigate through them.
Main Advanced Power Boot Tools Exit
System Time [10:55:25] System Date [Fri 05/07/2007] Legacy Diskette A [1.44M, 3.5 in]
SATA 1 [WDC WD800JD-00LSA0] SATA 2 [Not Detected] SATA 3 [Not Detected] SATA 4 [Not Detected]
SATA Coniguration System Information
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
BIOS SETUP UTILITY
Use [ENTER], [TAB] or [SHIFT-TAB] to select
a eld.
Use [+] or [-] to
congure system Time.
Select Screen
Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit
4.3.1 System Time [xx:xx:xx]
Allows you to set the system time.
4.3.2 System Date [Day xx/xx/xxxx]
Allows you to set the system date.
4.3.3 Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of oppy drive installed. Conguration options: [Disabled] [720K, 3.5 in.] [1.44M, 3.5 in.]
4-12 Chapter 4: BIOS setup
4.3.4 SATA 1~4
While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press <Enter> to display the IDE device information.
Main
SATA 1
Device : Hard Disk Vendor : WDC WD800JD-00LSA0 Size : 80.0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : 4 Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring: Supported
Type [Auto] LBA/Large Mode [Auto] Block(Multi-sector Transfer)M [Auto] PIO Mode [Auto] DMA Mode [Auto] SMART Monitoring [Auto] 32Bit Data Transfer [Enabled]
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
The BIOS automatically detects the values opposite the dimmed items (Device,
Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring). These values are not user-congurable. These items show
N/A if no IDE device is installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to [Auto] allows automatic selection of the
appropriate IDE device type. Select [CDROM] if you are specically conguring a
CD-ROM drive. Select [ARMD] (ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive.
Conguration options: [Not Installed] [Auto] [CDROM] [ARMD]
BIOS SETUP UTILITY
Select the type of device connected to the system.
Select Screen
Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA
mode disabled. Conguration options: [Disabled] [Auto]
Block (Multi-sector Transfer) M [Auto]
Enables or disables data multi-sectors transfers. When set to [Auto], the data transfer from and to the device occurs multiple sectors at a time if the device supports multi-sector transfer feature. When set to [Disabled], the data transfer from and to the device occurs one sector at a time.
Conguration options: [Disabled] [Auto]
PIO Mode [Auto]
Selects the PIO mode.
Conguration options: [Auto] [0] [1] [2] [3] [4]
ASUS P5K SE 4-13
DMA Mode [Auto]
Selects the DMA mode. Conguration options: [Auto] [SWDMA0] [SWDMA1]
[SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Conguration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Enabled]
Enables or disables 32-bit data transfer.
Conguration options: [Disabled] [Enabled]
4.3.5 SATA Conguration
The items in this menu allow you to set or change the congurations for the SATA
devices installed in the system. Select an item then press <Enter> if you want to
congure the item.
SATA Conguration
SATA Conguraton [Enhanced] Congure SATA as [IDE]
Hard Disk Write Protect [Disabled] SATA Detect Time Out (Sec) [35]
Options
Disabled Compatiable Enhanced
SATA Conguration [Enhanced]
Conguration options: [Disabled] [Compatible] [Enhanced]
Configure SATA as [IDE]
Sets the conguration for the Serial ATA connectors supported by the Southbridge chip. Conguration options: [IDE]
Hard Disk Write Protect [Disabled]
Disables or enables device write protection. This will be effective only if device is
accessed throuh BIOS. Conuration option: [Disabled] [Enabled]
SATA Detect Time Out (Sec) [35]
Selects the time out value for detecting ATA/ATAPI devices.
Conguration options: [0] [5] [10] [15] [20] [25] [30] [35]
4-14 Chapter 4: BIOS setup
4.3.6 System Information
This menu gives you an overview of the general system specications. The BIOS
automatically detects the items in this menu.
Main
AMIBIOS
Version : 0110 Build Date : 05/07/07
Processor
Type : Genuine Intel(R) CPU @ 2.80GHz Speed : 2800 MHz Count : 2
System Memory
Available : 1024 MB
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
AMI BIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specication.
System Memory
Displays the auto-detected system memory.
BIOS SETUP UTILITY
Select Screen
Select Item F1 General Help F10 Save and Exit ESC Exit
ASUS P5K SE 4-15
4.4 Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system devices.
Take caution when changing the settings of the Advanced menu items. Incorrect
eld values can cause the system to malfunction.
Main Advanced Power Boot Tools Exit
JumperFree Conguration USB Conguration
CPU Conguration
Chipset
Onboard Devices Conguration
PCIPnP
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
BIOS SETUP UTILITY
4.4.1 Jumperfree Conguration
Advanced
Congure System Frequency/Voltage
AI Overclocking [Auto] CPU Ratio Control [Auto]
DRAM Frequency [Auto]
DRAM Timing Control [Auto] DRAM Static Read Control [Auto]
Transaction Booster [Auto] Clock Over-Charging Mode [Auto]
CPU Spread Spectrum [Auto] PCIE Spread Spectrum [Auto]
Select Screen
Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit
Select the target CPU
frequency, and the
relevant parameters will be auto-adjusted.
Frequencies higher
than CPU manufacturer recomends are not guaranteed to be stable. If the system becomes unstable, return to the default.
AI Overclocking [Auto]
Allows selection of CPU overclocking options to achieve desired CPU internal
frequency. Select any one of the preset overclocking conguration options:
Manual Allows you to individually set overclocking parameters.
Auto
Standard
4-16 Chapter 4: BIOS setup
Loads the optimal settings for the system.
Loads the standard settings for the system.
Some of the following items appear when you set AI Overclocking to [Manual].
CPU Ratio Control [Auto]
Conguration options: [Auto] [Manual]
The following item appears when the CPU Ratio Control item is set to [Manual].
Ratio CMOS Setting [14]
Use the <+> and <-> keys to select the CMOS ratio values from 6 to 12.
FSB Frequency [XXX]
Displays the frequency sent by the clock generator to the system bus and PCI bus. Use the <+> and <-> keys to adjust the FSB frequency. You can also type the desired FSB frequency using the numeric keypad. The values range from 200 to 800. Refer to the table below for the correct Front Side Bus and CPU External Frequency settings.
PCIE Frequency [Auto]
Allows you to set the PCI Express frequency.
Conguration options: [Auto] [100] [101]~[149] [150].
FSB/CPU External Frequency Synchronization
Front Side Bus CPU External Frequency
FSB 1333 333 MHz
FSB 1066 266 MHz
FSB 800 200 MHz
DRAM Frequency [Auto]
Allows you to set the DDR2 operating frequency.
Conguration options: [Auto] [DDR2-667MHz] [DDR2-800MHz]
Selecting a very high DRAM frequency may cause the system to become unstable! If this happens, revert to the default setting.
ASUS P5K SE 4-17
DRAM Timing Control [Auto]
Allows you to set the DRAM timing control. Conguration options: [Auto] [MANUAL]
The following items appear when you set the DRAM Timing Control item to [Manual].
CAS# Latency [ 5]
Conguration options: [3] [4] [5] [6]
RAS# to CAS# Delay [ 5 DRAM Clocks]
Conguration options: [3 DRAM Clocks] [4 DRAM Clocks]~[9 DRAM Clocks]
[10 DRAM Clocks]
RAS# Precharge [ 5 DRAM Clocks]
Conguration options: [3 DRAM Clocks] [4 DRAM Clocks]~[9 DRAM Clocks]
[10 DRAM Clocks]
RAS# Activate to Precharge [9 DRAM Clocks]
Conguration options: [3 DRAM Clocks] [4 DRAM Clocks]~[17 DRAM Clocks]
[18 DRAM Clocks]
TWR [Auto]
Conguration options: [Auto] [ 1 DRAM Clocks]~[15 DRAM Clocks]
TRFC [Auto]
Conguration options: [Auto] [20 DRAM Clocks] [25 DRAM Clocks] [30 DRAM Clocks] [35 DRAM Clocks] [42 DRAM Clocks]
TWTR [Auto]
Conguration options: [Auto] [ 1 DRAM Clocks]~[15 DRAM Clocks]
TRRD [Auto]
Conguration options: [Auto] [ 1 DRAM Clocks]~[15 DRAM Clocks]
TRTP [Auto]
Conguration options: [Auto] [ 1 DRAM Clocks]~[15 DRAM Clocks]
DRAM Static Read Control [Auto]
Conguration options: [Auto] [Disabled] [Enabled]
Transaction Booster [Disabled]
Conguration options: [Auto] [Disabled] [Enabled]
Clock Over-Charging Mode [Auto]
Conguration options: [Auto] [700mV] [800mV] [900mV] [1000mV]
CPU Spread Spectrum [Auto]
Allows you to enable or disable the CPU spread spectrum.
Conguration options: [Auto] [Disabled]
4-18 Chapter 4: BIOS setup
PCIE Spread Spectrum [Auto]
Allows you to enable or disable the PCIE spread spectrum.
Conguration options: [Auto] [Disabled]
CPU Voltage [Auto]
Allows you to select the CPU voltage. Conguration options: [Auto] [1.7000V]
[1.6875V] [1.6750V] [1.6625V] [1.6500V] [1.6375V] [1.6250V] [1.6125V] [1.6000V] [1.5875V] [1.5750V] [1.5625V] [1.5500V] [1.5375V] [1.5250V] [1.5125V] [1.5000V] [1.4875V] [1.4750V] [1.4625V] [1.4500V] [1.4375V] [1.4250V] [1.4125V] [1.4000V] [1.3875V] [1.3750V] [1.3625V] [1.3500V] [1.3375V] [1.3250V] [1.3125V] [1.3000V] [1.2875V] [1.2750V] [1.2625V] [1.2500V] [1.2375V] [1.2250V] [1.2125V] [1.2000V] [1.1875V] [1.1750V] [1.1625V] [1.1500V] [1.1375V] [1.1250V] [1.1125V] [1.1000V]
Refer to the CPU documentation before setting the CPU voltage. Setting a high voltage may damage the CPU!
CPU Voltage Reference [Auto]
Conguration options: [Auto] [0.63x] [0.61x] [0.59x] [0.57x]
DRAM Voltage [Auto]
Allows you to select the DDR2 reference voltage.
Conguration options: [Auto] [1.80V] [1.85V] [1.90V] [1.95V] [2.00V] [2.05V] [2.10V]
[2.15V] [2.20V] [2.25V] [2.30V] [2.35V] [2.40V] [2.45V] [2.50V] [2.55V] [2.60V]
Refer to the DDR2 documentation before adjusting the memory voltage. Setting a very high memory voltage may damage the memory module(s)!
ASUS P5K SE 4-19
4.4.2 USB Conguration
The items in this menu allows you to change the USB-related features. Select an
item then press <Enter> to display the conguration options.
Advanced
USB Conguration
USB Devices Enabled: None
USB Functions [Enabled] USB 2.0 Controller [Enabled] USB 2.0 Controller Mode [HiSpeed] BIOS EHCI Hand-off [Enabled] Port 64/60 Emulation [Disabled] Legacy USB Support [Auto]
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
The USB Devices Enabled item shows auto-detected values. If no USB device is detected, the item shows None.
USB Functions [Enabled]
Allows you to enable or disable the USB functions. The following sub-items appear
when this item is set to [Enabled]. Conguration options: [Disabled] [Enabled]
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller.
Conguration options: [Enabled] [Disabled]
BIOS SETUP UTILITY
Options
Disabled Enhanced
Select Screen
Select Item
+- Change Option
F1 General Help F10 Save and Exit ESC Exit
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or FullSpeed (12 Mbps). This item appears only when you enable the USB 2.0
Controller item. Conguration options: [FullSpeed ] [HiSpeed ]
BIOS EHCI Hand-off [Enabled]
Allows you to enable support for operating systems without an EHCI hand-off
feature. Conguration options: [Disabled] [Enabled]
Port 64/60 Emulation [Disabled]
Allows you to enable or disable the I/O port 60h/64h emulation support. This item should be enabled for the complete USB keyboard legacy support for non-USB aware OSes. Conguration options: [Disabled] [Enabled]
4-20 Chapter 4: BIOS setup
Legacy USB Support [Auto]
Allows you to enable or disable support for legacy USB devices. Setting to [Auto] allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the
legacy USB support is disabled. Conguration options: [Disabled] [Enabled] [Auto]
4.4.3 CPU Conguration
The items in this menu show the CPU-related information that the BIOS automatically detects.
Advanced
Congure advanced CPU settings
Manufacturer:Intel Brand String:Genuine Intel(R) CPU @ 2.80 GHz
Frequency :2.80GHz
FSB Speed :800 MHz Cache L1 :32 KB Cache L2 :2048 KB CPUID :F44 Ratio Status:Unlocked (Max:14, Min:14) Ratio Actual Value :14
CPU Ratio Control [Auto] C1E Support [Enabled] Max CPUID Value Limit: [Disabled] Vanderpool Technology [Enabled] CPU TM function: [Enabled] Execute Disable Bit [Enabled] PECI [Enabled]
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
BIOS SETUP UTILITY
Options
Auto MANUAL
Select Screen
Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
CPU Ratio Control [Auto]
Conguration options: [Auto] [Manual]
The following item appears when the item CPU Ratio Control is set to [Manual].
Ratio CMOS Setting: [14]
Use the <+> and <-> keys to select the CMOS ratio values from 6 to 12.
C1E Support [Enabled]
Allows you to enable or disable C1E Support.
Conguration options: [Disabled] [Enabled]
Max CPUID Value Limit [Disabled]
Setting this item to [Enabled] allows legacy operating systems to boot even without support for CPUs with extended CPUID functions.
Conguration options: [Disabled] [Enabled]
ASUS P5K SE 4-21
Vanderpool Technology [Enabled]
Conguration options: [Enabled] [Disabled]
CPU TM Function [Enabled]
Conguration options: [Disabled] [Enabled]
Execute Disable Bit [Enabled]
Allows you to enable or disable the No-Execution Page Protection Technology.
Setting this item to [Disabled] forces the XD feature ag to always return to zero (0). Conguration options: [Disabled] [Enabled]
PECI [Enabled]
Allows you to enable or disable the PECI interface.
Conguration options: [Disabled] [Enabled]
The following item appears when you set CPU Ratio Control to [Auto]
Intel(R) SpeedStep (TM) Tech. [Disabled]
Conguration options: [Disabled] [Automatic]
4.4.4 Chipset
The Chipset menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu.
Advanced
Advanced Chipset Settings
WARMING: Setting wrong values in below sections may cause system to malfunction.
North Bridge Conguration
BIOS SETUP UTILITY
Congure North Bridge features.
North Bridge Conguration
Advanced
North Bridge Chipset Conguration
Memory Remap Feature [Enabled] Initiate Graphic Adapter [PEG/PCI] PEG Port Control [Auto] PEG Port Force x1 [Disabled]
4-22 Chapter 4: BIOS setup
BIOS SETUP UTILITY
ENABLE: Allow remapping of overlapped PCI memory above the total physical memory.
DISABLE: Do not allow remapping of memory.
Memory Remap Feature [Enabled]
Allows you to enabled or disable the remapping of the overlapped PCI memory above the total physical memory. Enable this option only when you
install 64-bit operating system. Conguration options: [Disabled] [Enabled]
Initiate Graphic Adapter [PEG/PCI]
Allows you to decide which graphics controller to use as the primary boot
device. Conguration options: [PCI/PEG] [PEG/PCI]
PEG Port Control [Auto]
Conguration options: [Auto] [Disabled]
PEG Force x1 [Disabled]
This item appears when the PEG Port Control item is set to [Auto].
Conguration options: [Enabled] [Disabled]
4.4.5 OnBoard Devices Conguration
Advanced
Onboard Device Conguraiton
High Denition Audio [Enabled]
Front Panel Type [HD Audio] Marvell IDE Controller [Enabled] Onboard PCIE GbE LAN [Enabled] LAN Option ROM [Disabled]
Serial Port1 Address [3F8/IRQ4]
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
High Denition Audio [Enabled]
Allows you to enable or disable the High Denition Audio. The following item
appears only when you enable this item.
Conguration options: [Enabled] [Disabled]
Front Panel Type [HD Audio]
Allows you to set the front panel audio connector (AAFP) mode to legacy
AC’97 or high-denition audio depending on the audio standard that the front panel audio module supports. Conguration options: [AC97] [HD Audio]
BIOS SETUP UTILITY
Enable or Disable
High Denition Audio
Controller
Select Screen
Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Marvell IDE Controller [Enabled]
Allows you to disable or enable the onboard Marvell® IDE controller.
Conguration options: [Enabled] [Disabled]
ASUS P5K SE 4-23
Onboard PCIE GbE LAN [Enabled]
Conguration options: [Enabled] [Disabled]
LAN Option ROM [Disabled]
This item appears only when you enable the previous item.
Conguration options: [Disabled] [Enabled]
Serial Port1 Address [3F8/IRQ4]
Allows you to select the Serial Port1 base address.
Conguration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3]
4.4.6 PCI PnP
The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices.
Take caution when changing the settings of the PCI PnP menu items. Incorrect
eld values can cause the system to malfunction.
Advanced
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections may cause system to malfunction.
Plug And Play O/S [No]
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
BIOS SETUP UTILITY
NO: lets the BIOS
congure all the
devices in the system. YES: lets the operating system
congure Plug and Play
(PnP) devices not
required for boot if
your system has a Plug and Play operating system.
Select Screen
Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Plug And Play O/S [No]
When set to [No], BIOS congures all the devices in the system. When set to
[Yes] and if you install a Plug and Play operating system, the operating system
congures the Plug and Play devices not required for boot. Conguration options: [No] [Yes]
4-24 Chapter 4: BIOS setup
4.5 Power menu
The Power menu items allow you to change the settings for the Advanced Power Management (APM). Select an item then press <Enter> to display the
conguration options.
Main Advanced Power Boot Tools Exit
Suspend Mode [Auto] Repost Video on S3 Resume [Disabled] ACPI Version [Disabled] ACPI APIC Support [Enabled]
APM Conguration
Hardware Monitor
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4.5.1 Suspend Mode [Auto]
Allows you to select the Advanced Conguration and Power Interface (ACPI) state
to be used for system suspend.
Conguration options: [S1 (POS) only] [S3 only] [Auto]
4.5.2 Repost Video on S3 Resume [Disabled]
Determines whether to invoke VGA BIOS POST on S3/STR resume.
Conguration options: [Disabled] [Enabled]
BIOS SETUP UTILITY
Select the ACPI state used for System Suspend.
Select Screen
Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
4.5.3 ACPI Version [Disabled]
Allows you to select the Advanced Conguration and Power Interface (ACPI) version supported. Conguration options: [Disabled] [Enabled]
4.5.4 ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Conguration and Power Interface
(ACPI) support in the Advanced Programmable Interrupt Controller (APIC). When set to Enabled, the ACPI APIC table pointer is included in the RSDT pointer list.
Conguration options: [Disabled] [Enabled]
ASUS P5K SE 4-25
4.5.5 APM Conguration
Power
APM Conguration
Restore on AC Power Loss [Power Off] Power On By RTC Alarm [Disabled] Power On By External Modems [Disabled] Power On By PCI Devices [Disabled] Power On By PCIE Devices [Disabled] Power On By PS/2 Keyboard [Disabled]
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Restore On AC Power Loss [Power Off]
When set to Power Off, the system goes into off state after an AC power loss. When set to Power On, the system goes on after an AC power loss. When set to Last State, the system goes into either off or on state, whatever the system state was before the AC power loss.
Conguration options: [Power Off] [Power On] [Last State]
Power On By RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake event. When this item is set to Enabled, the items RTC Alarm Date/ RTC Alarm Hour/ RTC Alarm Minute/
RTC Alarm Second will become user-congurable with set values. Conguration options: [Disabled] [Enabled]
BIOS SETUP UTILITY
<Enter> to select whether or not to restart the system after AC power loss.
Select Screen
Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
Power On By External Modems [Disabled]
This allows either settings of [Enabled] or [Disabled] for powering up the computer when the external modem receives a call while the computer is in Soft-off mode.
Conguration options: [Disabled] [Enabled]
The computer cannot receive or transmit data until the computer and
applications are fully running. Thus, connection cannot be made on the rst
try. Turning an external modem off and then back on while the computer is off
causes an initialization string that turns the system power on.
Power On By PCI Devices [Disabled]
Allows you to enable or disable the PME to wake up from S5 by PCI devices.
Conguration options: [Disabled] [Enabled]
Power On By PCIE Devices [Disabled]
Allows you to enable or disable the PCIE devices to generate a wake event.
Conguration options: [Disabled] [Enabled]
4-26 Chapter 4: BIOS setup
Power On By PS/2 Keyboard [Disabled]
Allows you to disable the Power On by PS/2 keyboard function or set specic keys
on the PS/2 keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.
Conguration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key]
4.5.6 Hardware Monitor
Power
Hardware Monitor
CPU Temperature [25ºC/77ºF] MB Temperature [34ºC/93ºF]
CPU Fan Speed (RPM) [4440RPM] CPU Q-Fan Control [Disabled] Chassis Fan Speed [4440RPM] Chassis Q-Fan Control [Disabled] Power Fan Speed (RPM) [N/A]
VCORE Voltage [ 1.080V]
3.3V Voltage [ 3.232V] 5V Voltage [ 5.040V] 12V Voltage [12.208V]
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
CPU Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures. Select [Ignored] if you do not wish to display the detected temperatures.
BIOS SETUP UTILITY
CPU Temperature
Select Screen
Select Item +- Change Field F1 General Help F10 Save and Exit ESC Exit
CPU Fan Speed [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the CPU fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the eld shows N/A.
CPU Q-Fan Control [Disabled]
Allows you to enable or disable the CPU Q-Fan controller.
Conguration options: [Disabled] [Enabled]
The CPU Fan Prole item appears when you enable the CPU Q-Fan Control feature.
ASUS P5K SE 4-27
CPU Fan Prole [Optimal]
Allows you to set the appropriate performance level of the CPU Q-Fan. When set to [Optimal], the CPU fan automatically adjusts depending on the CPU
temperature. Set this item to [Silent Mode] to minimize fan speed for quiet CPU fan
operation, or [Performance Mode] to achieve maximum CPU fan speed.
Conguration options: [Optimal] [Silent Mode] [Performance Mode]
Chassis Fan Speed [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the chassis fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the eld shows N/A.
Chassis Q-Fan Control [Disabled]
Allows you to enable or disable the chassis Q-Fan controller.
Conguration options: [Disabled] [Enabled]
The Chassis Fan Ratio and Chassis Target Temperature items appear when you enable the Chassis Q-Fan Control feature.
Chassis Fan Ratio [Auto]
Allows you to set the appropriate fan speed ratio for the chassis Q-Fan. When set to [Auto], the chassis fan automatically adjusts depending on the chassis
temperature. Set a low ratio to minimize fan speed for quiet chassis fan operation,
or a high ratio to achieve maximum chassis fan speed.
Conguration options: [Auto] [90%] [80%] [70%] [60%]
Chassis Target Temperature [37ºC]
Adjusts the CPU fan speed to make the CPU temperature as low as the selected temperature.
Conguration options: [28ºC] [31ºC] [34ºC] [37ºC] [40ºC] [43ºC] [46ºC]
Power Fan Speed (RPM) [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the power fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the eld shows N/A.
Vcore Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. Select [Ignored] if you do not want to detect this item.
4-28 Chapter 4: BIOS setup
4.6 Boot menu
The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu.
Main Advanced Power Boot Tools Exit
Boot Device Priority
Boot Settings Conguration
Security
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4.6.1 Boot Device Priority
Boot
Boot Device Priority
1st Boot Device [1st FLOPPY DRIVE] 2nd Boot Device [HDD:PM-WDC WD800JD] 3rd Boot Device [ATAPI CD-ROM]
BIOS SETUP UTILITY
BIOS SETUP UTILITY
Species the Boot
Device Priority
sequence.
A virtual oppy disk
drive (Floppy Drive B:) may appear when you set the CD-ROM drive as the
rst boot device.
Select Screen
Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Species the boot sequence from the
availabe devices.
A device enclosed in parenthesis has been disabled in the corresponding menu.
Select Screen
Select Item
Change Option
+-
F1 General Help F10 Save and Exit ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
1st ~ xxth Boot Device [xxx Drive]
These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system. Conguration options: [1st FLOPPY DRIVE] [Hard Drive] [ATAPI CD-ROM] [Disabled]
ASUS P5K SE 4-29
4.6.2 Boot Settings Conguration
Boot
Boot Settings Conguration
Quick Boot [Enabled] Full Screen Logo [Enabled] AddOn ROM Display Mode [Force BIOS] Bootup Num-Lock [On] Wait For ‘F1’ If Error [Enabled] Hit ‘DEL’ Message Display [Enabled] Interrupt 19 Capture [Disabled]
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items.
Conguration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
This allows you to enable or disable the full screen logo display feature.
Conguration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo2™ feature.
BIOS SETUP UTILITY
Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Select Screen
Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit
AddOn ROM Display Mode [Force BIOS]
Sets the display mode for option ROM.
Conguration options: [Force BIOS] [Keep Current]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Conguration options: [Off] [On]
Wait For ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for the F1 key to be pressed when error
occurs. Conguration options: [Disabled] [Enabled]
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message “Press DEL to run Setup”
during POST. Conguration options: [Disabled] [Enabled]
Interrupt 19 Capture [Disabled]
When set to [Enabled], this function allows the option ROMs to trap Interrupt 19.
Conguration options: [Disabled] [Enabled]
4-30 Chapter 4: BIOS setup
4.6.3 Security
The Security menu items allow you to change the system security settings. Select
an item then press <Enter> to display the conguration options.
Boot
Security Settings
Supervisor Password :Not Installed User Password :Not Installed
Change Supervisor Password Change User Password
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor Password item on top of the screen shows the default Not Installed. After you set a password, this item shows Installed.
To set a Supervisor Password:
1. Select the Change Supervisor Password item and press <Enter>.
2. From the password box, type a password composed of at least six letters and/or numbers, then press <Enter>.
3. Conrm the password when prompted.
The message “Password Installed” appears after you successfully set your password.
To change the supervisor password, follow the same steps as in setting a user password.
To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message “Password Uninstalled” appears.
BIOS SETUP UTILITY
<Enter> to change password. <Enter> again to disabled password.
Select Screen
Select Item Enter Change F1 General Help F10 Save and Exit ESC Exit
If you forget your BIOS password, you can clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section 2.6 Jumper for information on how to erase the RTC RAM.
After you have set a supervisor password, the other items appear to allow you to change other security settings.
ASUS P5K SE 4-31
Boot
Security Settings
Supervisor Password :Installed User Password :Installed
Change Supervisor Password User Access Level [Full Access] Change User Password Clear User Password Password Check [Setup]
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
BIOS SETUP UTILITY
<Enter> to change password. <Enter> again to disabled password.
Select Screen
Select Item Enter Change F1 General Help F10 Save and Exit ESC Exit
User Access Level [Full Access]
This item allows you to select the access restriction to the Setup items.
Conguration options: [No Access] [View Only] [Limited] [Full Access]
No Access prevents user access to the Setup utility.
View Only allows access but does not allow change to any eld.
Limited allows changes only to selected elds, such as Date and Time.
Full Access allows viewing and changing all the elds in the Setup utility.
Change User Password
Select this item to set or change the user password. The User Password item on top of the screen shows the default Not Installed. After you set a password, this item shows Installed.
To set a User Password:
1. Select the Change User Password item and press <Enter>.
2. On the password box that appears, type a password composed of at least six letters and/or numbers, then press <Enter>.
3. Conrm the password when prompted.
The message “Password Installed” appears after you set your password successfully.
To change the user password, follow the same steps as in setting a user password.
Clear User Password
Select this item to clear the user password.
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system.
Conguration options: [Setup] [Always]
4-32 Chapter 4: BIOS setup
4.7 Tools menu
The Tools menu items allow you to congure options for special functions. Select
an item then press <Enter> to display the sub-menu.
Main Advanced Power Boot Tools Exit
ASUS EZ Flash 2
ASUS O.C. Prole
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4.7.1 ASUS EZ Flash 2
Allows you to run ASUS EZ Flash 2. When you press <Enter>, a conrmation
message appears. Use the left/right arrow key to select between [Yes] or [No],
then press <Enter> to conrm your choice. Please see section 4.1.3 for details.
ASUSTek EZ Flash 2 BIOS ROM Utility V3.05
FLASH TYPE: WINBOND W25X80
Current ROM
BOARD: P5K SE VER: 0110 DATE: 05/07/07
PATH: C:\
A:
C:
BIOS SETUP UTILITY
BOARD: Unknown VER: Unknown DATE: Unknown
Update ROM
Press ENTER to run the utility to select and update BIOS. This utility doesn't support :
1.NTFS format
Select Screen
Select Item
Change Field
+-
Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Note
[Enter] Select or Load [B] Backup [ESC] Exit [Tab] Switch [Up/Down/Home/End] Move
ASUS P5K SE 4-33
4.7.2 ASUS O.C. Prole
This item allows you to store or load multiple BIOS settings.
Tools
O.C. PROFILE Conguration
O.C. Prole 1 Status :Not Installed O.C. Prole 2 Status :Not Installed
Save to Prole 1 Load from Prole 1
Save to Prole 2 Load from Prole 2
Start O.C. Prole
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Save to Proe 1/2
Allows you to save the current BIOS le to the BIOS Flash. Press <Enter> to save the le.
Load from Prole 1/2
Allows you to load the previous BIOS settings saved in the BIOS Flash. Press
<Enter> to load the le.
Start O.C. Prole
Allows you to run the utility to save and load CMOS. Press <Enter> to run the utility.
BIOS SETUP UTILITY
ASUSTek O.C. Prole Utility V1.05
Save to Prole 1
Select Screen
Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit
Current CMOS
BOARD: P5K SE VER: 0110 DATE: 05/07/07
PATH: C:\
A:
C:
Note
[Enter] Select or Load [B] Backup [ESC] Exit [Tab] Switch [Up/Down/Home/End] Move
Restore CMOS
BOARD: Unknown VER: Unknown DATE: Unknown
This function can support devices such as USB ash disk or oppy
disk with FAT 32/16 format and single partition only.
DO NOT shut down or reset the system while updating the BIOS to prevent the system boot failure!
4-34 Chapter 4: BIOS setup
Loading...