ARRIS WA840GV2 User Manual

User Guide

Wireless Access Point

WA840G

MOTOROLA INC. declares that WA840Gv2 ( FCC ID: ACQWA840GV2 ) is limited in

CH1~CH11 by specified firmware controlled in U.S.A.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE UNIT MUST NOT BE
EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THE UNIT.

CAUTION: TO ENSURE REGULATORY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES.

CAUTION: DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND

TROUBLESHOOTING INSTRUCTIONS. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.

This device must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the
product.

Postpone router installation until there is no risk of thunderstorm or lightning activity in the are a.

Do not overload outlets or extension cords, as this can result in a risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords,
damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard.

Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords where
they are attached to plugs and convenience receptacles, and examine the point where they exit from the product.

Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of the power cord.

Place this equipment on a stable surface.

When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the
following:

• Read all of the instructions {listed here and/or in the user manual} before you operate this equipment. Give particular attention to all safety precautions.
Retain the instructions for future reference.

• Comply with all warning and caution statements in the instructions. Observe all warning and caution symbols that are affixed to this equipment.

• Comply with all instructions that accompany this equipment.

• Avoid using this product during an electrical storm. There may be a risk of electric shock from lightning. For added protection for this product during a
lightning storm, or when it is left unattended and unus ed for long periods of time, unplug it from the wall outlet, and disconnect the cable system. This will
prevent damage to the product due to lightning and power surges.

• Operate this product only from the type of power source indicated on the product’s marking label. If you are not sure of the type of power supplied to your
home, consult your dealer or local power company.

• Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe
operating condition.

It is recommended that the customer install an AC surge protector in the AC outlet to which this device is connected. This is to avoid damaging the equipment by
local lightning strikes and other electrical surges.

Different types of cord sets may be used for connections to the main supply circuit. Use only a main line cord that complies with all applicable product safety
requirements of the country of use.

Installation of this product must be in accordance with national wiring codes.

Place unit to allow for easy access when disconnecting the power cord/adapter of the device from the AC wall outlet.

Wipe the unit with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners directly on the unit or use forced air to remove dust.

This product was qualified under test conditions that included the use of the supplied cables between system components. To be in compliance with regulations,
the user must use these cables and install them properly. Connect the unit to a grounding type AC wall outlet using the power adapter supplied with the unit.

Do not cover the device, or block the airflow to the device with any other objects. Keep the device away from excessive heat and humidity and keep the device
free from vibration and dust.

Installation must at all times conform to local regulations.

FCC Compliance Class B Digital Device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, the re is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfere nce to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by Motorola for compliance could void the user’s authority to operate the equipment.

The antennas used for this transmitter must be installed to provide a separation

distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure

compliance.

Canadian Compliance

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Cet appareil numérique de la classe B
respe cts tout es les e xigences d u Règlement s ur le matérie l brouilleur du Canada.

FCC Declaration of Conformity

Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044, 1-215-323-1000, declares under sole responsibility tha t the
WR850G, WE800G, WA840G, WN825G, WPCI810G, and BR700 compile with 47 CFR Parts 2 and 15 of the FCC Rules as a Class B digital device. This
device complies with Part 15 of FCC Rules. Operation of the device is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference that may cause undesired operation.

Wireless LAN Information

The WR850G, WE800G, WA840G, WN825G, and WPCI810G Wireless LAN products are wireless network products that uses Direct Sequence Spread
Spectrum (DSSS) radio technology. This product is designed to be inter-operable with any other wireless DSSS type product that complies with:

• The IEEE 802.11 Standard on Wireless LANs (Revision B), as defined and approved by the Institute of Electrical Electronics Engineers.

• The Wireless Fid elity (WiFi) c ertification as de fined by the Wireless Ethernet Compatibility Alliance (W ECA).

Wireless LAN and your Health

The WR850G, WE800G, WA840G, WN825G, and WPCI810G, like other radio devices, emits radio frequency electromagnetic energy, but operates within the
guidelines fo und in radio fre quency safety standards and recommendat ions.

Restrictions on Use of Wireless Devices

In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the
organization. For example, these situations may include:

• Using wireless equipment on board an airplane.

• Using wireless equipment in any environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the applicable policy for the use of wireless equipment in a specific organization or environment (such as airports), you are encouraged to

ask for authorization to use the device prior to turning on the equipment.
The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this product, or the

substitution or attachment of connecting cables and equipment other than specified by the manufacturer. Correction of interference caused by such unauthorized
modificatio n, subst it u tion, or a t tachment is the resp onsibility of the user.

The manufacturer and its authoriz ed rese llers or distributor s are not liable for any damage or violation of government regulations that may arise from failing to
comply with these guidelines.

FCC Certification

The WR850G, WE800G, WA840G, WN825G, and WPCI810G contains a radio transmitter and accordingly has
been certified as compliant with 47 CFR Part 15 of the FCC Rules for intentional radiators. Products that contain a
radio transmitter are labeled with FCC ID and the FCC logo.

Caution: Exposure t o Radio Frequency Radiation.

Canada - Industry Canada (IC)

The wireless radio of this device complies with RSS 210 ans RSS 102 of Industry Canada.
This Class B digitral device complies with Canadian ICES-003 (NMB-003).

Cet appareil numérique de la classe B respects toutes les exigences du Règlement sur le matériel brouilleur du Canada

Copyright © 2003 by Motorola, Inc.
All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as

translation, transformation or adaptation) without written permission from Motorola, Inc.
Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to

provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including,
but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or changes in
the product(s) described in this manual at any time.

MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Microsoft Windows screen shots are used by
permission of Microsoft Corporation. All other product or service names are the property of their respective owners. © Motorola, Inc. 2003

Contents

Section 1:Overview _______________________ 1-1

Features ................................................................................................................ 1-2

Understanding Your User Guide......................................................................... 1-3

Box Contents ........................................................................................................ 1-4

Wireless Connections.......................................................................................... 1-4

Access Point .......................................................................................................1-4

TCP/IP.................................................................................................................1-4

Static IP Address...........................................................................................................1-5

Dynamic IP Address......................................................................................................1-5

Understanding Wireless ................................................................................................1-5

Wireless Range...................................................................................................1-6

Recommended Wireless Environment ................................................................1-6

Type of Networks.................................................................................................. 1-7

Access Point Mode..............................................................................................1-7

WDS Access Point Mode ....................................................................................1-7

Access Point Physical Description..................................................................... 1-8

Back of Access Point...........................................................................................1-8

Front of Access Point ..........................................................................................1-9

LED Description ................................................................................................1-10

Section 2:Installation______________________ 2-1

Hardware Setup .................................................................................................... 2-1

Antenna Installation.............................................................................................2-1

Access Point Physical Installation .......................................................................2-2

Horizontal Installation ....................................................................................................2-2

Vertical Installation ........................................................................................................2-3

Wall Mount Installation ..................................................................................................2-3

Electrical Connection to Access Point.................................................................2-6

Easy Software Setup............................................................................................ 2-6

Manual Software Setup........................................................................................ 2-6

Wired Connection to Access Point ......................................................................2-7

Wireless Connection to Access Point..................................................................2-8

Configure Your Computers.................................................................................. 2-9

Configuring Windows 98SE and ME .................................................................2-10

Configuring Windows 2000 ...............................................................................2-12

Configuring Windows XP...................................................................................2-15

Configure Your Wireless Security Settings...................................................... 2-19

Logging In .........................................................................................................2-19

Wireless Security Setup ....................................................................................2-20

CONTENTS I

CONTENTS

Section 3:Configuration ___________________ 3-1

Using the Web-Based Configuration Utility ........................................................3-1

Logging In ...........................................................................................................3-1

Navigation ...........................................................................................................3-2

Help, Restart, and Logout ...................................................................................3-2

Configuring Wireless Network Settings..............................................................3-3

Wireless - Basic ..................................................................................................3-3

Wireless - Security ..............................................................................................3-5

Wireless - Site Monitor......................................................................................3-11

Wireless - Advanced .........................................................................................3-13

Configuring Control Panel Settings...................................................................3-16

Control Panel - Network Access........................................................................3-16

Control Panel - Device Security ........................................................................ 3-18

Control Panel - Firmware Update......................................................................3-18

Control Panel - Configuration Data ...................................................................3-19

Section 4:Troubleshooting _________________ 4-1

Contact................................................................................................................4-1

Hardware Solutions...............................................................................................4-1

My computer is experiencing difficulty in connecting to the AP.....................................4-2

Software Solutions................................................................................................4-3

I would like to see if my Internet connection is alive......................................................4-3

I cannot access the Web-Based Configuration Utility for the AP...................................4-4

Section 5:Glossary _______________________ 5-1

II CONTENTS

Section 1:Overview

Congratulations on purchasing the Motorola Wireless Access Point
WA840G. With this unit, you have entered the world of freedom and
independence – freedom from wires and the independence to
communicate wherever YOU choose.

Because the Access Point (AP) is built with both the popular 802.11b
wireless standard and the new nearly 5-times-faster 802.11g
standard, your unit provides you the ultimate in flexibility and speed.
With Wi-Fi
connections are robust and secure, giving you the security to
communicate without fear that your signal might be compromised.

Upgradeable firmware keeps the AP’s control software up-to-date.
The WA840G captures the latest technology in a package that will
stay current for many years, protect your home network, and provide
you easy home network management.

Wireless Access Point WA840G

®

Protected Access (WPA) included, your wireless

SECTION 1, OVERVIEW 1-1

SECTION 1 OVERVIEW

Your wireless access point offers these great features:

Wireless Connectivity

Connects your PC to your wireless network and allows you to
communicate unfettered. Using the 802.11g and 802.11b
wireless standards will ensure compliance with the now and the
future.

Secure Transmission

Protection against Internet intruders is crucial. Of course the
product supports single session encryption when communicating
with just the client, but it also supports network encryption, when
communicating with larger surrounding wireless networks.

Supports Wi-Fi Protected Access (WPA) and Media Access
Control (MAC) filtering protocols, giving you the choice to share
your Internet connection with only those whom you designate.

Your Motorola Wireless Access Point WA840G connects and
protects you. Built-in security coupled with upgradeable firmware
ensures your Access Point will work for you for years to come.

Features

! CD-ROM based Installation Assistant for easy installation

! Web-based configuration of features using any web browser

! Compatibility with both 802.11g and 802.11b standards

! Wireless security using WPA, 802.1X Authentication, and

Advanced Encryption Standard (AES)

! Wireless Distribution System (WDS) mode supporting peer-to-

peer communication with other WA840G or WR850G units

! Firmware upgrade to stay current with latest specification

! Easily extend your home network, in the office, or even at

tradeshows

1-2 SECTION 1, OVERVIEW

OVERVIEW SECTION 1

Understanding Your User Guide

The User Guide is subdivided into the following sections:

Overview Provides a general introduction for using your

product, the type of technology used, and
recommended practices for using it.

Installation It is assumed that you will use the Installation

Assistant on the CD-ROM to setup your unit. If not,
then refer to this section for details on getting your
unit up and running.

Once you have completed this section, your unit will
be active and ready to work.

Configuration Provides descriptive details for using the

Configuration Utility to manage your unit.

Glossary Defines the terms and acronyms.

SECTION 1, OVERVIEW 1-3

SECTION 1 OVERVIEW

A

Box Contents

Your box contains the following:

CD-ROM

Power

Adapter

ntenna

Power

Cord

Ethernet

Cable

Base Station Stand

WA840G

Quick Start

Guide

Wireless Connections

The various technologies and features utilized by your wireless
access point require some conceptual explanation so that you can
make the correct choices in configuring your wireless access point.

Access Point

Access Points (AP) wirelessly connect networks together, such as
your network with the Internet (which can be thought of as a very
large network). Or, by configuring multiple clients such as laptops,
each using their own AP, you are able to create your own private
wireless Ad-Hoc network.

TCP/IP

TCP/IP (Transmission Control Protocol/Internet Protocol) comprises
the backbone of the Internet. IP moves packets of data between
nodes while TCP verifies delivery from client to server. The device

1-4 SECTION 1, OVERVIEW

OVERVIEW SECTION 1

you hook up to your wireless access point will identify itself with an IP
address so that the network will know where to retrieve and deposit
requested information.

Static IP Address

A static IP address is a fixed address that is assigned manually to a
device on the network. Static IP addresses must be unique and
cannot be shared, therefore they are used in situations where the
address should never change, like print servers or PC servers.

Dynamic IP Address

A dynamic IP address is a temporary IP number, dynamically or
randomly generated by a DHCP server. The address lasts only as
long as the server allots, usually in the space of a day or two. When
the IP address expires, the client is automatically reassigned a new
IP address, ensuring smooth communication.

Understanding Wireless

Your wireless AP uses a radio transmission technology defined by
the Institute of Electrical and Electronics Engineers (IEEE) called

802.11 or Wi-Fi (Wireless Fidelity). This standard is subdivided into
distinct categories of speed and the frequency spectrum used,
designated by the lower case letter after the standard. For example,
your AP supports both the ‘b’ and ‘g’ specifications. The 802.11b
specification transmits data rates up to 11 Mbps while the 802.11g
specifications transmits data rates up to 54 Mbps. These are
theoretical speeds so your performance may vary. The radio waves
radiate out in a donut-shaped pattern. The waves travel through walls
and floors, but transmission power and distance are affected. The
theoretical distance limit is 1,000 feet (305 meters), but actual
throughput and distance varies.

Both standards operate in the 2.4 GHz range, meaning other
electrical appliance also might interfere with the AP – televisions,
radios, microwave ovens, and 2.4 GHz cordless telephones. Thus
positioning your AP where it encounters the least interference gains
the greatest benefit to maintaining a quality connection.

SECTION 1, OVERVIEW 1-5

SECTION 1 OVERVIEW

Wireless Range

The following describes different scenarios for the expected range of
the coverage area of the unit. This table is only a guide and coverage
varies due to local conditions.

Data Rate Open Area Closed Area

54 Mbps Up to 100 ft (30m) Up to 60 ft (18m)

11 Mbps Up to 900 feet (275 m) Up to 160 feet (49 m)

5.5 Mbps Up to 1300 feet (396 m) Up to 200 feet (61 m)

2 or 1 Mbps Up to 1500 feet (457 m) Up to 300 feet (91 m)

Recommended Wireless Environment

The following information helps you to achieve the best wireless
performance:

! Placing your base station in the physical center of your network is

the premium location because the antenna radiates out the signal
in all directions.

! Placing the unit in a higher location, such as atop a cabinet, helps

to disperse the signal cleanly, especially to receiving locations on
upper stories.

! Direct line of sight achieves better performance, but obviously is

not always achievable.

! Try to avoid placing the unit next to large solid objects like

computer cases, monitors, walls, fireplaces, etc. This helps the
signal penetrate more cleanly.

! Other wireless devices like televisions, radios, microwaves and

2.4 GHz cordless telephones can interfere with the signal. Keep
devices away from the unit.

! Mirrors, especially silver-coated, negatively affect transmission

performance.

1-6 SECTION 1, OVERVIEW

OVERVIEW SECTION 1

Type of Networks

Your AP supports several different usage scenarios and the following
examples illustrate the flexibility of your WA840G. Some scenarios
require additional hardware that can be purchased.

Access Point Mode

In this mode, the WA840G connects wireless clients to a wired
Ethernet network. This is the most likely scenario you will use, as it
shares an Internet connection with your laptop or other wireless
client.

WDS Access Point Mode

In this mode, the WA840G connects its wireless clients to other
Access Points wirelessly.

SECTION 1, OVERVIEW 1-7

SECTION 1 OVERVIEW

A

Access Point Physical Description

The following sections describe the physical characteristics of the
unit.

Back of Access Point

The following illustration shows the WA840G back panel:

Reset

Power

Power

Receptacle

LAN

LAN

Port

Reset
Button

ntenna

Antenna

Feature Description

Power The power adapter receptacle.

LAN Port This port connects to the Internet, your LAN

network, or PC with an Ethernet cable. This
enables communication between the devices.
The LAN port supports either 10BASE-T or
100BASE-T transmission speeds as well as
straight-through and Crossover Ethernet cables.

1-8 SECTION 1, OVERVIEW

OVERVIEW SECTION 1

Feature Description

Reset Button A dual-function button. It either resets your unit

or resets the unit to the default login settings.

If the AP is experiencing trouble connecting to
the Internet, briefly press and release the Reset
button to reset the AP. This retains its
configuration information.

To reset the unit to the factory defaults, while
the unit is powered, press and hold the Reset
button for more than 5 seconds.

This clears the AP’s user settings, including
User ID, Password, IP Address, and Subnet
Mask. Refer to the Configuration section for re­configuring the AP.

Antenna The antenna used for wireless connections. You

are able to rotate and tilt the antenna to gain the
best signal reception.

Front of Access Point

The following illustration shows the front of the unit.

123

r

e

w

o

P

The LEDs of the access point indicate operational information of its
status.

s

e

s

c

i

e

l

v

e

e

r

i

D

W

SECTION 1, OVERVIEW 1-9

SECTION 1 OVERVIEW

LED Description

The underlined items represent network activity.

LED Condition Color Status

1 Power ON

Blinking

Blinking/ON

Green

Green

Red

The device is powered on and operating normally.

Firmware update is in progress.

The power LED turns RED as soon as the reset
button is depressed. If the reset button is held down
for more than 5 seconds, the LED starts to blink
during which the access point’s default user name,
password and IP address will be restored. The LED
then turns OFF until the reset button is released. The
power LED keeps blinking RED if the firmware is
corrupted indicating the firmware needs to be
restored.

2 Wireless OFF

None

No mobile station or AP has associated with this
device.

ON

Red

The wireless interface has been disabled by the
firmware.

ON/Blinking

802.11b/802.11g connection exists in this wireless

Green

domain/active traffic present

3 Device OFF

None

No external Ethernet device has been attached and
detected. The Ethernet link is down.

Amber

ON/Blinking

10BaseT link detected/active traffic present.

.

ON/Blinking

100BaseT link detected/active traffic present.

Green

1-10 SECTION 1, OVERVIEW

Section 2:Installation

To get your network up and running:

! Setup your hardware.

! Insert the CD-ROM for Software Setup. Follow the prompts.

If you prefer to setup the Access Point’s (AP) software manually,
refer to the Manual Software Setup found in this section.

The following sections provide detailed instructions for completing
these tasks.

Hardware Setup

Hardware setup includes:

! Antenna Installation: verifying the antenna is connected to the

unit.

! Physical Installation: where you physically place your unit.

! Electrical Connection: how to power your unit.

Antenna Installation

When shipped, the antenna is already installed on the main unit. If
you have to detach and reattach the antenna to the main unit:

1 Take the bottom of the antenna and locate, on the right backside

of the AP, the threaded knob.

2 Screw the antenna connector clockwise on to the threaded knob

until firmly seated. Do not overtighten.

SECTION 2, INSTALLATION

2-1

SECTION 2 INSTALLATION

Access Point Physical Installation

You can install the AP in various different physical orientations –
horizontally, vertically, or hung on the wall. Your own needs
determine the best placement.

Horizontal Installation

1 Place the AP in the desired location and follow the procedures

below for connecting and configuring the unit.

2-2

SECTION 2, INSTALLATION

INSTALLATION SECTION 2

Vertical Installation

1 To use the AP in a vertical position, insert it into the supplied

base. Ensure that the antenna’s location is on top, as it does not
allow the unit to nestle into the base. The AP’s foot slides snugly
into the base to keep the unit stable.

2 Follow the installation procedures for connecting and configuring

the unit.

Wall Mount Installation

If you mount the AP on the wall, you must:

! Locate the unit as specified by the local or national codes

governing residential or business communications services.

! Follow all local standards for installing a network interface

unit/network interface device (NIU/NID).

If possible, mount the AP to concrete, masonry, a wooden stud, or
other very solid wall material. Use anchors if necessary; for example
if you must mount the unit on drywall. Mounting the unit on the wall
may decrease performance.

SECTION 2, INSTALLATION

2-3

SECTION 2 INSTALLATION

To mount your AP on the wall:

1 Print the Wall Mounting Template.

3.15”

[80.00mm]

MODEL WA840G

INPUT VOLTAGE: +5VDC, 2A
FCC ID: F2NWA840G

MODEL: WA840G

Tested To Comply

With FCC Standards

FOR HOME OR OFF ICE USE

The illustration is drawn at a one-to-one scale, which means that
when printed, it provides the exact dimensions required to mount the
unit.

PART NUMBER: AAAAAA-BBB-CC

S/N: PPPPMMYJJJSSSSSC AABBCCCC

WIRELESS MAC: AB CD EF 01 23 45

MADE IN TAIWAN

2 Click the Print icon or choose Print from the File menu to display

the Print dialog box. (A sample print dialog follows.)

2-4

SECTION 2, INSTALLATION

INSTALLATION SECTION 2

Be sure you print the template at 100% scale and that Fit to page is
not

checked in the Print dialog box.

3 Click OK to print the template.

4 Measure the printed template with a ruler to ensure that it is the

correct size.

5 Use a center punch to mark the center of the holes on the wall.

6 On the wall, locate the marks for the mounting holes you just

made.

WARNING!

Before drilling holes, check the structure for potential
damage to water, gas, or electric lines.

7 Drill the holes to a depth of at least 3.8 cm (1½ inches).

8 If necessary, seat an anchor in each hole. Use M5 x 38 mm

(#10-16 x 1½ inch) screws with a flat underside and maximum
screw head diameter of 10.5 mm to mount the unit.

9 Using a screwdriver, turn each screw until part of it protrudes

from the wall, as shown:

! There must be 4.0 mm (.16 inches) between the wall and the

underside of the screw head.

! The maximum distance from the wall to the top of the screw

head is 7.6 mm (.3 in).

7.6 mm (.3 inches)
maximum

10.5 mm (.4 inches)
maximum

4.0 mm

10 Remove the front two plastic feet, nearest to the LED panel, from

the bottom of the unit to uncover the keyholes.

11 Place the unit so the keyholes are above the mounting screws.

12 Slide the AP down until it stops against the top of the keyhole

opening.

13 Follow the installation procedures for connecting and configuring

the unit.

SECTION 2, INSTALLATION

2-5

SECTION 2 INSTALLATION

Electrical Connection to Access Point

Your AP does not have an On/Off power switch and therefore will
only be powered on by plugging in the power adapter. Use only the
original power adapter supplied with your unit.

To power

supply

1 Connect the power adapter to the AP’s Power port, found on the

back of the unit.

2 Then plug the power adapter into a grounded and surge

protected power outlet.

! The Power LED on the front panel lights green when

Easy Software Setup

Run the Installation Wizard program from the supplied CD-ROM to
quickly setup your network. Once your network is up and running,
refer to Section 3:Configuration for advanced configuration.

Manual Software Setup

If you’d prefer to manually setup your network, use this section to
configure it. This section details the physical connection of the AP to
your network as well as the configuration needed by your PC.

To set up your wireless network:

! Physically connect and power on the Access Point

connected properly.

2-6

! Configure your PCs

! Enter Wireless Security settings

SECTION 2, INSTALLATION