400 MHz to 6.0 GHz Cable and Antenna Analyzer
150 kHz to 7.1 GHz Spectrum Analyzer
10 MHz to 7.1 GHz Power Meter
MT8220TSpecifications
Introduction
Anritsu introduces the next-generation, high-performance handheld Base Station Analyzer for installation and
maintenance of wireless networks. Delivered with a standard three-year warranty, the MT8220T BTS Master is the only
all-in-one, touchscreen handheld tool that combines cable and antenna testing, signal analysis for all cellular standards,
ultra-sensitive spectrum analysis, sophisticated interference tracking, and a vector signal generator for receiver testing in
a compact, easy-to-use instrument.
Cable and Antenna Analyzer Highlights
• Measurements: RL, VSWR, Cable Loss, DTF, Phase, Gain
Warm-Up TimeAfter 10 minutes of warm-up time, where the instrument is left in the ON state.
Reference SignalWhen using internal reference signal.
Time Base ErrorTime base error = frequency accuracy x measured frequency
Typical PerformanceTypical specifications in parenthesis () represent the mean value of measured units and do not include any
UncertaintyA coverage factor of x1 is applied to the measurement uncertainties to facilitate comparison with other
Calibration CycleCalibration is within the recommended 12 month period (residual specifications also require calibration kit
All specifications and characteristics apply to Revision 2 instruments under the following conditions, unless
otherwise stated:
guard-bands or uncertainties. They are not warranted.
Typical specifications that are not in parenthesis are not tested and not warranted. They are generally
dBW/m
Occupied Bandwidth (Measures 99 % to 1 % power channel of a signal)
Channel Power (measures the total power in a specified bandwidth)
ACPR (Adjacent Channel Power Ratio)
AM/FM/SSB Demodulation (AM, wide/narrow FM, upper/lower SSB), (audio out only)
C/I (Carrier-to-Interference ratio)
Emission Mask (recall limit lines as emission mask)
Coverage Mapping (requires Option 431)
IQ Waveform Capture (requires Option 24)
PIM Alert Application (available for download)
PIM Hunting
Limit Line EditFrequency, Amplitude, Add Point, Add Vertical, Delete Point, Next Point Left/Right
Limit Line MoveTo Current Center Frequency, By dB or Hz, To Marker 1, Offset from Marker 1
Gated Sweep (requires Option 90)
→
B, B ↔ C, Max Hold, Min Hold
→
C, B ↔ C, Max Hold, Min Hold, A – B → C, B – A → C, Relative Reference (dB), Scale
Marker Table (On/Off/Large), All Markers Off
Marker Frequency to Center, Delta Marker to Span, Marker to Reference Level
Frequency
Maximum Continuous Input+30 dBm
Frequency Range150 kHz to 7.1 GHz (usable to 0 Hz)
Tuning Resolution1 Hz
×
Frequency ReferenceAging: ± 1.0
Frequency Span Accuracy± 3
Sweep TimeMinimum 100 ms, 7 µs to 3600 s in zero span
Sweep Time Accuracy± 2 % in zero span
×
10–6/10 years
10–7 (25 °C ± 25 °C) + aging, 10 Hz to 7.1 GHz including zero span
Bandwidth
Resolution Bandwidth (RBW)1 Hz to 3 MHz in 1–3 sequence ± 10 % (–3 dB bandwidth)
Video Bandwidth (VBW)1 Hz to 3 MHz in 1–3 sequence ± 10 % (–3 dB bandwidth)
RBW with Quasi-Peak Detection200 Hz, 9 kHz, 120 kHz (–6 dB bandwidth)
VBW with Quasi-Peak DetectionAuto VBW is On, RBW/VBW = 1
VBW/Average TypeLinear/Log
6 of 32PN: 11410-00698 Rev. APMT8220T TDS
SpecificationsMT8220T
Spectrum Analyzer
(continued)
Spectral Purity
SSB Phase Noise–100 dBc/Hz @ 10 kHz, 20 kHz, and 30 kHz offset from carrier
–102 dBc/Hz @ 100 kHz offset from carrier
Amplitude Ranges
Dynamic Range> 95 dB (600 MHz, 3.5 GHz), 2/3 (TOI-DANL) in 1 Hz RBW
Measurement RangeDANL to +30 dBm
Display Range1 to 15 dB/div in 1 dB steps, ten divisions displayed
Reference Level Range–150 dBm to +30 dBm
Attenuator Resolution0 dB to 65 dB, 5.0 dB steps
Amplitude Accuracy
Input attenuation
150 kHz to ≤10 MHz ± 1.50 dB± 1.50 dB± 1.50 dB-
150 kHz to 4.0 GHz---± 1.50 dB
>10 MHz to 4.0 GHz± 1.25 dB± 1.75 dB± 1.75 dB>4.0 GHz to 6.5 GHz-± 1.75 dB± 1.75 dB>4.0 GHz to 7.1 GHz± 1.75 dB--± 1.75 dB
>6.5 GHz to 7.1 GHz-± 2.00 dB± 3.00 dB-
–90 dBm, 150 kHz to 3.2 GHz
–84 dBm, > 3.2 GHz to 7.1 GHz
Preamp On (RF input terminated, 0 dB input attenuation)
–100 dBm, 10 MHz to 7.1 GHz
–60 dBc, –70 dBc typical
–70 dBc typical
MT8220T TDSPN: 11410-00698 Rev. AP7 of 32
MT8220TSpecifications
GPS Receiver
General
GPS Time/Location IndicatorTime, Latitude, Longitude and Altitude on display
High Frequency AccuracySpectrum Analyzer, Interference Analyzer, Wireless Measurements
GPS Lock Accuracywhen GPS antenna is connected:
Supplied Antenna2000-1760-R GPS Antenna, SMA(m), 25 dB gain, 2.5 VDC to 3.7 VDC
Power Meter
General
Frequency Range10 MHz to 7.1 GHz
Measurement Range–120 dBm to +30 dBm
Maximum Power+30 dBm without attenuator
Application OptionsImpedance (50 Ω, 75 Ω, Other)
SetupOn/Off, Antenna Voltage 3.3 V/5.0 V, GPS Info
Time, Latitude, Longitude and Altitude with trace storage
×
10–8 with GPS On, 3 minutes after satellite lock in selected mode
± 2.5
after antenna is disconnected:
± 5.0
×
10–8 for 3 days, 0 ºC to 50 ºC ambient temperature
ConnectorSMA, female
FrequencyCenter/Start/Stop, Span, Frequency Step, Signal Standard, Channel #, Full Band
AmplitudeMaximum, Minimum, Offset, Relative On/Off, Units, Auto Scale
AverageAcquisition Fast/Med/Slow, # of Running Averages
LimitsLimit On/Off, Limit Upper/Lower
Span1 kHz to 100 MHz
Display Range–140 dBm to +30 dBm, ≤ 40 dB span
Offset Range0 dB to +100 dB
VSWR1.5:1 typical
AccuracySame as Spectrum Analyzer
High Accuracy Power Meter (Option 19)
Power Sensor Model MA24105AMA24106AMA24108A/18A/26A MA24208A/18AMA24330A/40A/50A
Measurement Uncertainty ± 0.17 dB
(for complete specifications)
AmplitudeMaximum, Minimum, Offset, Relative On/Off, Units, Auto Scale
Average# of Running Averages, Max Hold
Zero/CalZero On/Off, Cal Factor (Center Frequency, Signal Standard)
LimitsLimit On/Off, Limit Upper/Lower
Description Inline High
Frequency Range 350 MHz to 4 GHz50 MHz to 6 GHz10 MHz to
a. Expanded uncertainty with K=2 for power measurements of a CW signal greater than +20 dBm with a matched load.
Notes:
Measurement results referenced to the input side of the sensor.
b. Total RSS measurement uncertainty (0 ºC to 50 ºC) f or power measurements of a CW signal greater than –20 dBm with zero
mismatch errors.
c. Expanded uncertainty with K=2 for power measurements of a CW signal greater than –20 dBm with zero mismatch errors.
d. Power uncertainty expressed with two sigma confidence level for CW measurement after zero operation. Includes
calibration factor and linearity over temperature uncertainties, but not the effects of mismatch, zero set and drift, or noise.
e. Includes lineari ty over temperature uncertainties, but not the effects of calibrati on factor, mismatch, zero set and drift, and
noise.
(requires external USB power sensor, sold separately)
High Accuracy
RF Power Sensor
–40 dBm to
+23 dBm
(0.1 µW to 200 mW)
b
±0.16dB
Microwave USB
Power Sensor
8/18/26 GHz
(8/18 GHz)
Type K(m), 50 Ω
(26 GHz)
–40 dBm to
+20 dBm
(0.1 µW to 100 mW)
Power, Burst
Average Power
c
±0.18dB
Microwave
Universal USB
Power Sensor
10 MHz to 8/18 GHz 10 MHz to
Type N(m), 50 ΩType K(m), 50 Ω
–60 dBm to
+20 dBm
(1 nW to 100 mW)
True-RMS, Slot
Power, Burst
Average Power
±0.17dB
Microwave CW USB
Power Sensor
33/40/50 GHz
(33/40 GHz)
Type V(m), 50 Ω
(50 GHz)
–70 dBm to
+20 dBm
(0.1 nW to 100 mW)
Average Power
d
±0.17dB
e
8 of 32PN: 11410-00698 Rev. APMT8220T TDS
SpecificationsMT8220T
Bias-Tee (Option 10)
General
SetupOn/Off, Voltage, Current (Low/High)
Voltage Range+12 V to +32 V
Current (Low/High)250 mA/450 mA, 1 A surge for 100 ms
Resolution0.1 V
Vector Signal Generator (Option 23)
Setup Parameters
FrequencyFrequency, Signal Standard, Channel Number, Interferer Offset
AmplitudeSignal/Interferer/Noise Level in dBm, Level Offset,
64QAM – US Digital Cable5.056941 MSPS, RRC filtered, alpha = 0.18
W-CDMA PilotQPSK, 3.84 MSPS, RRC filtered, alpha=0.22, Data = PN9
DVB-C1.152 MSPS, RRC filtered, alpha = 0.5, Data = PN9
J.83C Digital Cable16QAM, 5 MSPS, RRC filtered, alpha = 0.13
Signal (CW/Modulated/Off), Interferer (CW/Modulated/Off), Noise (On/Off)
RFOn/Off
×
10–7 (25 °C ± 25 °C) + aging
–124 dBm to –8 dBm, Modulated/Noise/Multi-carrier
(at least 30 minutes warm-up after 1 hour non-operating at 15 °C to 35 °C ambient, excludes load match errors,
(400 MHz to 2.0 GHz)(>2.0 to 4.0 GHz)(>4.0 to 6.0 GHz)
kHz/500 kHz
Customized Signal Patterns
Input Waveform for
MST Pattern ConverterASCII Text or MATLAB
Number of Waveforms≤ 1000
Sampling Rate
(contact Anritsu)
Bandwidth
Time
Length
®
file format
12.500 MHz6.250 MHz1.625 MHz
10.0 MHz5.0 MHz1.2 MHz
≤ 4 s≤ 8 s≤ 32 s
N × 8 SamplesN × 4 SamplesN × 4 Samples
MT8220T TDSPN: 11410-00698 Rev. AP9 of 32
MT8220TSpecifications
I/Q Waveform Capture (Option 24)
General
ModeSpectrum Analyzer
Capture ModeSingle or Continuous
TriggerFree Run, External (Rising/Falling), Delay
Maximum Capture Length800 ms
Maximum Sample Rate40 MHz
Maximum Signal Bandwidth32 MHz
Interference Analyzer (Option 25)
Measurements
SpectrumField Strength
Occupied Bandwidth
Channel Power
Adjacent Channel Power Ratio (ACPR)
AM/FM/SSB Demodulation (Wide/Narrow FM, Upper/Lower SSB), (audio out only)
Carrier-to-Interference ratio (C/I)
SpectrogramCollect data up to 72 hours
Received Signal Strength Indicator (RSSI)Collect data up to 168 hours (one week)
Signal StrengthGives visual and aural indication of signal strength
Signal IDID up to 12 FM, GSM, W-CDMA, CDMA or Wi-Fi signals based on RF bandwidth
Interference MappingDraw multiple bearings of signal strength from GPS location on on-screen map
Pan and Zoom on-screen maps
Support for MA2700A Handheld Interference Hunter (see Optional Accessories)
Channel Power
Occupied Bandwidth
Burst Power
Average Burst power
Frequency Error
Phase Error
EVM
Origin Offset
C/I
Magnitude Error
Script Master™
Setup Parameters
GSM/EDGE SelectAuto, GSM, EDGE
FrequencyCenter, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
AmplitudePower Offset, Auto Range, Adjust Range
SweepSingle/Continuous, Trigger Sweep
Save/RecallSetup, Measurement, Screen Shots (JPEG - save only), to Internal/External Memory
Measurement Summary ScreenOverall Measurements
RF Measurements
Frequency Error± 10 Hz + time base error, 99 % confidence level
Occupied BandwidthBandwidth within which lies 99 % of the power transmitted on a single channel
Burst Power Error± 1.5 dB; ± 1 dB typical (–50 dBm to +20 dBm)
Demodulation Measurements
GMSK Modulation Quality (RMS Phase)
Measurement Accuracy± 1
Residual Error (GMSK)1
8PSK Modulation Quality (EVM)
Measurement Accuracy± 1.5 %
Residual Error (8PSK)2.5 %
º
º
12 of 32PN: 11410-00698 Rev. APMT8220T TDS
SpecificationsMT8220T
W-CDMA/HSPA+ Measurements (Option 881)
Measurements
RFDemodulationOver-the-Air (OTA)Pass/Fail
Band Spectrum
Channel Spectrum
Channel Power
Occupied Bandwidth
Peak-to-Average Power
Spectral Emission Mask
Single Carrier ACLR
Multi-carrier ACLR
RF Summary
Code Domain Power Graph
P-CPICH Power
Channel Power
Noise Floor
EVM
Carrier Feed Through
Peak Code Domain Error
Carrier Frequency
Frequency Error
Control Channel Power
Abs/Rel/Delta Power
CPICH, P-CCPCH
S-CCPCH, PICH
P-SCH, S-SCH
HSPA+
Power vs. Time
Constellation
Code Domain Power Table
Code, Status
EVM, Modulation Type
Power, Code Utilization
Power Amplifier Capacity
Codogram
Modulation Summary
Scrambling Code Scanner (Six)
Scrambling Codes
CPICH
E
c/Io
E
c
Pilot Dominance
OTA Total Power
Multipath Scanner (Six)
Six Multipaths
Tau
Distance
RSCP
Relative Power
Multipath Power
View Pass/Fail Limits
All, RF, Demod
Available Measurements
Max Output Power
Frequency Error
EVM
CPICH
Occupied Bandwidth
Spectral Mask
ACLR
PCDE
P-CCPCH
S-CCPCH
Code Spread 3
PICH
Code 128
Script Master™
Test Models
1 (16), (32), (64)
2
3 (16), (32)
4 (+CPICH), (-CPICH)
5 (2 HS), (4 HS), (8 HS)
Setup Parameters
Scrambling Code, ThresholdAuto, Manual
User SelectableScrambling Code, S-CCPCH Spread, S-CCPCH Code, PICH Code, Threshold, Max Amp Power, CPICH Power,
Maximum Spreading Factor256, 512
FrequencyCenter, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
AmplitudeScale/Division, Power Offset, Auto Range, Adjust Range, Units (dBm/W)
MarkerSix Markers, Table On/Off
SweepSingle/Continuous, Trigger Sweep
Save/RecallSetup, Measurement, Screen Shots (JPEG - save only), to Internal/External Memory
(QPSK/8PSK/16QAM/64QAM)
Slot Power
DwPTS Power
Noise Floor
Frequency Error
Tau
Scrambling Code
EVM
Peak EVM
Peak Code Domain Error
CDP Marker
Modulation Summary
Slot SelectionAuto, 0-6
TriggerTrigger Type (No Trigger/GPS/External), External Trigger (Rising/Falling), Tau Offset
SYNC-DL CodeAuto, 0-31
Maximum UsersAuto, 2, 4, 6, 8, 10, 12, 14, 16
User SelectableUplink Switch Point, Number of Carriers (1, 3), Tau Offset
Demodulation TypeAuto, QPSK, 8PSK, 16QAM, 64QAM
FrequencyCenter, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
AmplitudeScale/Division, Power Offset, Auto Range, Adjust Range, Units (dBm/W)
SweepHold/Run, Trigger Sweep
Save/RecallSetup, Measurement, Screen Shots (JPEG - save only), to Internal/External Memory
Code Scan (32)
Scrambling Code Group
Tau
E
c/Io
DwPTS Power
Pilot Dominance
Tau Scan (Six)
Sync-DL#
Tau
E
c/Io
DwPTS Power
Pilot Dominance
Record
Run/Hold
View Pass/Fail Limits
All, RF, Demod
Available Measurements
Occupied Bandwidth
Channel Power
Channel Power RCC
On/Off Ratio
Peak-to-Average Ratio
Frequency Error
EVM
Peak EVM
Peak Code Domain Error
Tau
Noise Floor
RF Measurements
RF Channel Power Accuracy (RRC)± 1.5 dB; ± 1.0 dB typical, (slot power –40 dBm to +10 dBm)
Frequency Error± 10 Hz + time base error, in the presence of a downlink slot
Ref Signal Power (RS)
Sync Signal Power (SS)
EVM – rms, peak, max hold
Frequency Error – Hz, ppm
Carrier Frequency
Cell ID
Control Channel Power
Bar Graph or Table View
RS, P-SS, S-SS
PBCH, PCFICH, PHICH, PDCCH
Total Power (Table View)
EVM per Control Channel
Tx Time Alignment
Modulation Summary
Includes EVM by modulation
Antenna Icons
Detects active antennas (1 or 2)
Scanner
Cell ID (Group, Sector)
S-SS, RSRP, RSRQ, SINR
Dominance
Modulation Results – On/Off
Auto Save - On/Off
Tx Test
Scanner
RS Power of MIMO antennas (2x2, 4x4)
Cell ID, Average Power
Delta Power (Max-Min)
Graph of Antenna Power
Modulation Results – On/Off
Mapping
On-screen
S-SS, RSRP, RSRQ, or SINR
Scanner
Modulation Results – Off
Carrier Aggregation
Up to 5 component carriers (CC1 to CC5)
CP, MIMO status, RS & SS Power, EVM,
Frequency Error, Time Alignment Error,
Cell ID
eMBMS
Cell ID, RSRP
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
ACLR
Frequency Error
Carrier Frequency
Dominance
EVM peak, rms
Frame EVM, rms
Frame EVM by mod type
RS, SS Power
RS EVM
P-SS, S-SS, Power, EVM
PBCH, PCFICH, PHICH, PDCCH
Power, EVM
Cell, Group, Sector ID
OSTP
Tx Time Alignment
Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
LTE/LTE-A FDD RF Measurements
RF Channel Power Accuracy± 1.5 dB; ± 1.0 dB typical (RF input –50 dBm to +10 dBm)
LTE/LTE-A FDD Modulation Measurements
RS Power Accuracy± 1.0 dB typical, (RF input –50 dBm to +10 dBm)
Frequency Error± 10 Hz + time base error, 99 % confidence level
Residual EVM (rms)2.0 % typical (E-UTRA Test Model 3.1, RF Input –50 dBm to +10 dBm)
LTE/LTE-A FDD Over-the-Air (OTA) Measurements
ScannerSix strongest signals if present
Tx TestScanner – Three strongest signals if present
MappingMap On-screen S-SS, RSRP, RSRQ, or SINR of Cell ID with strongest signal
Carrier AggregationUp to 5 component carriers specified (CC1 to CC5)
Evolved Multimedia Broadcast
Multicast Services (eMBMS)Reports the Cell ID and measures the Received Signal Received Power (RSRP)
Auto Save – Sync Signal power and Modulation Results with GPS information
RS Power – Strongest Signal
Scanner – three strongest signals if present
Save and Export Mapping data: KML, MTD (tab delimited)
Automatic detection of CP and MIMO status for each active CC
RS Power & RS Delta Power, SS Power, EVM (peak and rms), Freq Error (Hz & ppm), TAE, Cell ID
MT8220T TDSPN: 11410-00698 Rev. AP15 of 32
MT8220TSpecifications
LTE/LTE-A FDD/TDD Measurements (Options 883 and 886)
LTE/LTE-A TDD Measurements
RFModulationOver-the-Air (OTA)Pass/Fail
Channel Spectrum
Channel Power
Occupied Bandwidth
Power vs. Time
Frame View
Sub-Frame View
Total Frame Power
DwPTS Power
Transmit Off Power
Cell ID
AmplitudeScale/Division, Power Offset, Auto Range, Adjust Range
SweepSingle/Continuous, Trigger Sweep
EVM ModeAuto, PBCH only, Max Hold
Cyclic Prefix (CP)Auto, Normal, Extended
TriggerNo Trigger/Ext Trigger, Rising/Falling
Save/RecallSetup, Measurement, Screen Shots (JPEG - save only), to Internal/External Memory
Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
Scanner
Cell ID (Group, Sector)
S-SS, RSRP, RSRQ, SINR
Dominance
Modulation Results – On/Off
Auto Save - On/Off
Tx Test
Scanner
RS Power of MIMO antennas (2x2, 4x4)
Cell ID, Average Power
Delta Power (Max-Min)
Graph of Antenna Power
Modulation Results – On/Off
Mapping
On-screen
S-SS, RSRP, RSRQ, or SINR
Scanner
Modulation Results – Off
Carrier Aggregation
Up to 5 component carriers (CC1 to CC5)
CP, MIMO status, RS & SS Power, EVM,
Frequency Error, Time Alignment Error,
Cell ID
(continued)
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
ACLR
Frequency Error
Carrier Frequency
Dominance
EVM peak, rms
Frame EVM, rms
Frame EVM by mod type
RS, SS Power
RS EVM
P-SS, S-SS, Power, EVM
PBCH, PCFICH, PHICH, PDCCH
Power, EVM
Cell, Group, Sector ID
OSTP
Tx Time Alignment
Frame Power
DwPTS Power
Transmit Off Power
Timing Error
LTE/LTE-A TDD RF Measurements
RF Channel Power Accuracy± 1.5 dB; ± 1.0 dB typical (RF input –30 dBm to +10 dBm)
LTE/LTE-A TDD Modulation Measurements
RS Power Accuracy± 1.0 dB typical, (RF input –50 dBm to +10 dBm)
Frequency Error± 10 Hz + time base error, 99 % confidence level
Residual EVM (rms)2.0 % typical (E-UTRA Test Model 3.1, RF Input –30 dBm to +10 dBm)
LTE/LTE-A TDD Over-the-Air (OTA) Measurements
ScannerSix strongest signals if present
Tx TestScanner – Three strongest signals if present
MappingMap On-screen S-SS, RSRP, RSRQ, or SINR of Cell ID with strongest signal
Carrier AggregationUp to 5 component carriers specified (CC1 to CC5)
Auto Save – Sync Signal power and Modulation Results with GPS information
RS Power – Strongest Signal
Scanner – three strongest signals if present
Save and Export Mapping data: KML, MTD (tab delimited)
Automatic detection of CP and MIMO status for each active CC
RS Power & RS Delta Power, SS Power, EVM (peak and rms), Freq Error (Hz & ppm), TAE, Cell ID
16 of 32PN: 11410-00698 Rev. APMT8220T TDS
SpecificationsMT8220T
NB-IoT Measurements (Option 887)
Measurements
NB-IoT ModeGuard Band, Standalone
RF Measurements
Spectral Emission MaskMask Type: NB-IoT Fixed
Summary ScreenCarrier Frequency
Channel Power
Occupied Bandwidth
NPSS Power
NSSS Power
NPBCH Power
NPDCCH or NPDSCH Power
Cell ID
RSRP
RSRQ
SINR
Spectral Emission Mask Pass/Fail
Pilot Power
Channel Power
Noise Floor
Rho
Carrier Feed Through
Tau
RMS Phase Error
Frequency Error
Abs/Rel/ Power
Pilot
Page
Sync
Q Page
Code Domain Power Table
Code
Status
Power
Multiple Codes
Code Utilization
Modulation Summary
PN SetupPN Trigger (No Trigger, GPS, External), PN Search Type (Auto, Manual), PN Offset
Walsh Codes64, 128
FrequencyCenter, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
AmplitudeScale/Division, Power Offset, Auto Range, Adjust Range, Units (dBm/W)
SweepSingle/Continuous, Trigger Sweep
Save/RecallSetup, Measurement, Screen Shots (JPEG - save only), to Internal/External Memory
Pilot Scanner (Nine)
PN
E
c/Io
Tau
Pilot Power
Channel Power
Pilot Dominance
Multipath Scanner (Six)
E
c/Io
Tau
Channel Power
Multipath Power
Limit Test – 10 Tests Averaged
Rho
Adjusted Rho
Multipath
Pilot Dominance
Pilot Power
Pass/Fail Status
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
Peak-to-Average Power
Spectral Mask Test
Frequency Error
Channel Frequency
Pilot Power
Noise Floor
Rho
Carrier Feed Through
Tau
RMS Phase Error
Code Utilization
Measured PN
Pilot Dominance
Multipath Power
CDMA RF Measurements
RF Channel Power Accuracy± 1.5 dB; ± 1.0 dB typical (RF input –50 dBm to +20 dBm)
CDMA Demodulation Measurements
Frequency Error± 10 Hz + time base error, 99 % confidence level (in slow mode)
Pilot & MAC Power
Channel Power
Frequency Error
Rho Pilot
Rho Overall
Data Modulation
Noise Floor
MAC Code Domain Power Table
Code
Status
Power
Code Utilization
Data Code Domain Power
Active Data Power
Data Modulation
Rho Pilot
Rho Overall
Maximum Data CDP
Minimum Data CDP
Modulation Summary
PN SetupPN Trigger (No Trigger, GPS, External), PN Search Type (Auto, Manual), PN Offset
Walsh Codes64, 128
MeasurementSpeed Fast, Normal, Slow
Slot TypeAuto, Active, Idle
FrequencyCenter, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
AmplitudeScale/Division, Power Offset, Auto Range, Adjust Range, Units (dBm/W)
SweepSingle/Continuous, Trigger Sweep
Save/RecallSetup, Measurement, Screen Shots (JPEG - save only), to Internal/External Memory
(continued)
Pilot Scanner (Nine)
PN
E
c/Io
Tau
Pilot Power
Channel Power
Pilot Dominance
Mulitpath Scanner (Six)
E
c/Io
Tau
Channel Power
Multipath Power
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
Peak-to-Average Power
Carrier Frequency
Frequency Error
Spectral Mask
Noise Floor
Pilot Power
RMS Phase Error
Tau
Code Utilization
Measured PN
Pilot Dominance
Mulitpath Power
EV-DO RF Measurements
RF Channel Power Accuracy± 1.5 dB; ± 1.0 dB typical (RF input –50 dBm to +20 dBm)
EV-DO Demodulation Measurements
EV-DO CompatibilityRev 0 and Rev A
Frequency Error± 10 Hz + time base error, 99 % confidence level
Rho Accuracy± 0.01, for Rho > 0.9
Residual Rho> 0.995 typical, > 0.99, maximum (RF input –50 dBm to +20 dBm)
PN OffsetWithin 1
Pilot Power Accuracy± 1.0 dB typical, relative to channel power
Tau± 0.5 µs typical, ± 1.0 µs maximum
EV-DO Over-the-Air (OTA) Measurements
Pilot ScannerNine strongest pilots
Multipath ScannerMultipath power of six signals relative to strongest pilot
×
64 chips
MT8220T TDSPN: 11410-00698 Rev. AP19 of 32
MT8220TSpecifications
WiMAX Fixed/Mobile Measurements (Option 885)
WiMAX Fixed Measurements
RFDemodulationOver-the-Air (OTA)Pass/Fail
Channel Spectrum
Channel Power
Occupied Bandwidth
Power vs. Time
Channel Power
Preamble Power
Data Burst Power
Crest Factor
ACPR
RF Summary
Constellation
RCE (RMS/Peak)
EVM (RMS/Peak)
Frequency Error
Carrier Frequency
Base Station ID
Spectral Flatness
Adjacent Subcarrier Flatness
EVM vs. Subcarrier/Symbol
RCE (RMS/Peak)
EVM (RMS/Peak)
Frequency Error
Carrier Frequency
Base Station ID
Sector ID (Mobile)
Modulation Summary
There are no additional OTA
Measurements
RF and Demodulation Measurements
can be made OTA
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
Burst Power
Preamble Power
Crest Factor
Frequency Error
Carrier Frequency
EVM
RCE
Base Station ID
FrequencyCenter, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
AmplitudeScale/Division, Power Offset, Auto Range, Adjust Range
SweepSingle/Continuous, Trigger Sweep
Save/RecallSetup, Measurement, Screen Shot (JPEG - save only), to Internal/External Memory
RCE (RMS/Peak)
EVM (RMS/Peak)
Frequency Error
CINR
Base Station ID
Sector ID
Spectral Flatness
Adjacent Subcarrier Flatness
EVM vs. Subcarrier/Symbol
RCE (RMS/Peak)
EVM (RMS/Peak)
Frequency Error
CINR
Base Station ID
Sector ID
DL-MAP (Tree View)
Modulation Summary
Zone TypePUSC
Span (MHz)5, 10, 20, 30
FrequencyCenter, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
AmplitudeScale/Division, Power Offset, Auto Range, Adjust Range
SweepSingle/Continuous, Trigger Sweep
Save/RecallSetup, Measurement, Screen Shot (JPEG - save only), to Internal/External Memory
Channel Power Monitor
Preamble Scanner (Six)
Preamble
Relative Power
Cell ID
Sector ID
PCINR
Dominant Preamble
Base Station ID
Auto Save - On/Off
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
Downlink Burst Power
Uplink Burst Power
Preamble Power
Crest Factor
Frequency Error
Carrier Frequency
EVM
RCE
Sector ID
WiMAX Mobile RF Measurements
RF Channel Power Accuracy± 1.5 dB; ± 1.0 dB typical, (RF input –50 dBm to +20 dBm)
WiMAX Mobile Demodulation Measurements
Frequency Error2
Residual EVM (rms)2.5 % typical, 3.0 % maximum (RF Input –50 dBm to +20 dBm)
(temperature range 15 °C to 35 °C)
(temperature range 15 °C to 35 °C)
×
10–8 + time base error, 99 % confidence level
WiMAX Mobile Over-the-Air (OTA) Measurements
Channel Power MonitorOver time (one week), measurement time interval 1 s to 60 s
Preamble ScannerSix strongest Preambles
Auto SaveYes
GPS Tagging and LoggingYes
1. Mobile WiMAX conforms to IEEE Std. 802.16e-2005, WiMAX Forum® Air Interface - Mobile System Profile - Release 1.0 Certified, System Profiles according to WMF-T24-001-R010v07
MT8220T TDSPN: 11410-00698 Rev. AP21 of 32
MT8220TSpecifications
General Specifications
System Parameters
Internal Trace/Setup Memory> 30,000 traces
External Trace/Setup MemoryLimited by size of USB Flash drive
File Management
Connectors
Ethernet InterfaceRJ45, 10/100 Mbps, connect to PC or LAN for remote access
External Reference InBNC, female, 50 Ω, Maximum Input +10 dB
SystemStatus (Temperature, Battery Info, Serial Number, Firmware Version, Options Installed)
System OptionsName, Date and Time, Ethernet Configuration, Volume,
Mode SwitchingAuto-Stores/Recalls most recently used Setup Parameters in the Mode
File TypesVary with measurement mode
RecallSetups, Measurements
DeleteSelected file or files from internal/external memory (USB)
File Sort MethodBy Name/Date/Type, Ascend/Descend
RF OutType N, female, 50 Ω, Maximum Input +23 dBm, ± 50 VDC, (Reflection In)
External Power5.5 mm barrel connector, 12 VDC to 14.5 VDC, < 5.0 A
USB InterfaceTwo Type A, Connect Flash Drive and Power Sensor
Headset Jack3.5 mm 3-wire headset jack
Reference OutBNC, female, 50 Ω, 10 MHz
IF OutBNC, female, 50 Ω, 140 MHz
Self Test, Application Self Test, GPS
Display (Brightness, Blank, Default, Black & White, Night Vision, High Contrast, Invert Black & White)
Share Center Frequency and Power Offset (All Modes or Not Shared)
Language (English, French, German, Spanish, Chinese, Japanese, Korean, Italian, Russian, Portuguese)
Reset (Factory Defaults, Master Reset, Update Firmware)
FileSave, Recall, Copy, Delete
SaveSetups, Measurements, Screen Shots (JPEG)
CopySelected file or files to internal/external memory (USB)
RF InType N, female, 50 Ω, Maximum Input +30 dBm, ± 50 VDC
GPSSMA, female
One 5-pin mini-B, Connect to PC for data transfer
Display and Keyboard
Battery
Battery Operation2.5 hours, typical
Battery Charging Limits0 °C to +45 °C, Relative Humidity ≤ 80 %
Regulatory Compliance
European UnionEMC 2014/30/EU, EN 61326:2013, CISPR 11/EN 55011, IEC/EN 61000-4-2/3/4/5/6/8/11
Australia and New ZealandRCM AS/NZS 4417:2012
Environmental
Operating Temperature Range–10 ºC to 55 ºC
Storage Temperature Range–51 ºC to 71 ºC
Maximum Relative Humidity95 % RH at 30 ºC, non-condensing
Pixel DefectsNo more than five defective pixels (99.9989% good pixels)
KeyboardBacklit (Red for Night Vision, White for all other display modes)
TypeLi-Ion
Low Voltage Directive 2014/35/EU
Safety EN 61010-1:2010
RoHS Directive 2011/65/EU applies to instruments with CE marking placed on the market after July 22, 2017
CanadaICES-1(A)/NMB-1(A)
South KoreaKCC-REM-A21-0004
MIL-PRF-28800F Class 2
Altitude4600 meters, operating and non-operating
Size315 mm x 211 mm x 102 mm (12.4 in x 8.3 in x 4.0 in)
Weight4.7 kg (10.3 lb)
n
MIL-STD-810G, Method 511.5, Procedure 1
Warranty
DurationStandard three-year warranty (one-year warranty on battery)
22 of 32PN: 11410-00698 Rev. APMT8220T TDS
SpecificationsMT8220T
Line Sweep Tools™
Trace Capture
Browse to InstrumentView and copy traces from the test equipment to your PC using Windows Explorer
Open Legacy FilesOpen DAT files captured with Handheld Software Tools v6.61
Open Current FilesOpen VNA or DAT files
Traces
Report Generation
Report GeneratorIncludes GPS location along with measurements
Trace Validation
Next Trace ButtonNext Trace and Previous Trace arrow keys allow quick switching between traces
Tools
Measurement CalculatorConverts Real, Imaginary, Magnitude, Phase, RL, VSWR, Rho, and Transmit power
Signal Standard EditorCreates new band and channel tables
(for your PC)
Capture Plots ToThe Line Sweep Tools screen, DAT files, Database, or JPEG
Trace TypesReturn Loss, VSWR, DTF-RL, DTF-VSWR, Cable Loss, Smith Chart, and PIM
Trace FormatsDAT, VNA, CSV, PNG, BMP, JPG, HTML, Data Base, and PDF
Report FormatCreate reports in HTML or PDF format
Report SetupReport Title, Company, Prepared for, Location, Date and Time, Filename, Company logo
Presets7 presets allow “one click” setting of up to 6 markers and one limit line
Marker Controls6 regular Markers, Marker Peak, Marker Valley, Marker between, and frequency entry
Delta Markers6 Delta markers
Limit LineEnable and drag or value entry. Also works with presets
Cable EditorAllows creation of custom cable parameters
Distance to FaultConverts a Return Loss trace to a Distance to Fault trace
Renaming Grid36 user definable phrases for creation of file names, trace titles, and trace subtitles
Connectivity
Master Software Tools™
Mapping
Folder Spectrogram
(GPS required)
Spectrum Analyzer ModeMapInfo, MapPoint
Mobile WiMAX OTA, LTE OTA OptionsGoogle Earth, Google Maps, MapInfo
Folder Spectrogram – 2D ViewCreates a composite file of multiple traces
Video Folder Spectrogram – 2D ViewCreate AVI file to export for management review/reports
Folder Spectrogram – 3D ViewViews (Set Threshold, Markers)
ConnectionsEthernet, USB cable, and USB memory stick
(for your PC)
(Spectrum Monitoring for Interference Analysis and Spectrum Clearing)
Peak Power, Total Power, Peak Frequency, Histogram, Average Power (Max/Min)
File Filter (Violations over limit lines or deviations from averages)
Playback
- 3D (Rotate X, Y, Z Axis, Level Scale, Signal ID)
- 2D View (Frequency or Time Domain, Signal ID)
- Top Down
Playback (Frequency and/or Time Domain)
List/Parameter Editors
TracesAdd, delete, and modify limit lines and markers
Product UpdatesAuto-checks Anritsu website for latest revision firmware
Pass/FailCreate, download, or edit Signal Analysis Pass/Fail Limits
LanguagesAdd custom language or modify non-English language menus
Script Master™
GSM/GPRS/EDGE or W-CDMA/HSPA+ ModeAutomate Signal Analysis testing requirements with annotated how-to pictures
Channel Scanner ModeAutomate scan up to 1200 channels, repeat for sets of 20 channels, repeat all channels
Connectivity
ConnectionsConnect to PC using USB or Ethernet
MT8220T TDSPN: 11410-00698 Rev. AP23 of 32
MT8220TSpecifications
easyMap Tools™
Outdoor Maps
On-Line SourcesGoogle Maps, Cloud Made Open-Source Maps
Pan & Zoom ModeAZM map file format allows pan and zoom on-instrument
Geo-ReferencedWorks with instrument based GPS
Map ConversionConvert scanned maps to geo-referenced
Indoor Maps
General
Web Remote Control
Software RequiredHTML 5 Compliant Browser – Newer versions of Chrome, Firefox, Internet Explorer and others
Operating SystemiOS, Windows, Linux, Android operating systems that can host the HTML 5 Compliant browser
Remote HardwarePCs, Tablets, and Smart Phones with Ethernet or Wi-Fi connections and a HTML 5 Compliant browser
Display ModesNormal: All modes & displays supported
Users/InstrumentsOne user/device can view and control many instruments
(for your PC)
Legacy ModeMAP format is compatible with older firmware
MT8220T-0098 Standard Calibration to ISO17025 and ANSI/NCSL Z540-1. Includes calibration certificate.
MT8220T-0099
Premium Calibration to ISO17025 and ANSI/NCSL Z540-1. Includes calibration certificate, test
report, and uncertainty data.
MT8220T TDSPN: 11410-00698 Rev. AP25 of 32
MT8220TSpecifications
Standard Accessories
Manuals
(Soft copy at
(included with instrument)
www.anritsu.com
Troubleshooting Guides
)
(soft copy at
Part Number Description
2000-1686-R Soft Carrying Case
2000-1760-R GPS Antenna, SMA(m), 25 dB gain, 2.5 VDC to 3.7 VDC
2000-1691-R Stylus with Coiled Tether
2000-1371-R Ethernet Cable, 213 cm (7 ft)
3-2000-1498 USB A-mini B Cable, 305 cm (10 ft)
Part Number Description
10100-00065 Product Information, Compliance, and Safety
10580-00366 BTS Master User Guide
10580-00230 Cable and Antenna Analyzer Measurement Guide
10580-00349 Spectrum Analyzer Measurement Guide
10580-00240 Power Meter Measurement Guide
10580-00232 Vector Signal Generator Measurement Guide
10580-00234 3GPP Signal Analyzer Measurement Guide
10580-00235 3GPP2 Signal Analyzer Measurement Guide
10580-00236 WiMAX Signal Analyzer Measurement Guide
10580-00367 Programming Manual
10580-00368 Maintenance Manual
www.anritsu.com
Part Number Description
11410-00473 Cable, Antenna and Components
11410-00551 Spectrum Analyzers
11410-00472 Interference
11410-00566 LTE eNodeB Base Stations
11410-00615 TD-LTE eNodeB Base Stations
11410-00466 GSM/GPRS/EDGE Base Stations
11410-00463 W-CDMA/HSDPA Base Stations
11410-00465 TD-SCDMA/HSDPA Base Stations
11410-00467 cdmaOne/CDMA2000 1X Base Stations
11410-00468 CDMA2000 1xEV-DO Base Stations
11410-00470 Fixed WiMAX Base Stations
11410-00469 Mobile WiMAX Base Stations
633-75 Rechargeable Li-Ion Battery, 7500 mAh
40-187-R AC/DC Power Supply
806-141-R Automotive Power Adapter, 12 VDC, 60 Watts
Certificate of Calibration
)
Power Sensors
(for complete ordering information, see the respective data sheets of each sensor)
Part Number Description
MA24105A Inline Peak Power Sensor, 350 MHz to 4 GHz, +51.76 dBm
MA24106A High Accuracy RF Power Sensor, 50 MHz to 6 GHz, +23 dBm
MA24108A Microwave USB Power Sensor, 10 MHz to 8 GHz, +20 dBm
MA24118A Microwave USB Power Sensor, 10 MHz to 18 GHz, +20 dBm
MA24126A Microwave USB Power Sensor, 10 MHz to 26 GHz, +20 dBm
MA24208A Microwave Universal USB Power Sensor,
MA24218A Microwave Universal USB Power Sensor,
MA24330A Microwave CW USB Power Sensor, 10 MHz to 33 GHz, +20 dBm
MA24340A Microwave CW USB Power Sensor, 10 MHz to 40 GHz, +20 dBm
MA24350A Microwave CW USB Power Sensor, 10 MHz to 50 GHz, +20 dBm
MA25100A RF Power Indicator
10 MHz to 8 GHz, +20 dBm to –60 dBm
10 MHz to 18 GHz, +20 dBm to –60 dBm
26 of 32PN: 11410-00698 Rev. APMT8220T TDS
SpecificationsMT8220T
Optional Accessories
Backpack and Transit Cases
Miscellaneous Accessories
Part Number Description
67135 Anritsu Backpack (for handheld instrument and PC)
760-243-R Large Transit Case with Wheels and Handle
760-261-R Large Transit Case with Wheels and Handle
760-262-R Transit Case for MA2700A, several Yagi antennas and filters
760-271-R Transit Case for Portable Directional Antennas and Port Extender
760-286-R Compact Transit Case with Wheels and Handle
Part Number Description
2000-1374-R External Dual Charger for Li-lon Batteries
2000-1689-R EMI Near Field Probe Kit
2000-1797-R Touchscreen Protective Film, 8.4 in
MA2700A Handheld Interference Hunter (For full specifications, refer to the MA2700A
2000-1884-R PIM Hunter™ Test Probe (For full specifications, refer to the 2000-1884-R
2000-1691-R Stylus with Coiled Tether
MA25401A Atomic Clock, External, 10 MHz Frequency Reference (see 11410-01134 for
2000-1798-R Port Extender, DC to 6 GHz, N(m) to N(f)
56 cm x 45.5 cm x 26.5 cm (22.07" x 17.92" x 10.42")
63.1 cm x 50 cm x 30 cm (24.83" x 19.69" x 11.88"), space for MA2700A,
antennas, filters, instrument inside soft case, and other interference
hunting accessories/tools
52.4 cm x 42.8 cm x 20.6 cm (20.62" x 16.87" x 8.12")
(for 2000-1777-R, 2000-1778-R, 2000-1779-R, 2000-1798-R)
55.6 cm x 35.5 cm x 22.9 cm (21.89" x 13.98" x 9.01")
633-75 Rechargeable Li-Ion Battery, 7500 mAh
Technical Data Sheet 11410-00692)
Technical Data Sheet 11410-00999)
details)
Calibration Components, 50 Ω
Calibration Components, 75 Ω
Part Number Description
OSLN50A-8 High Performance Type N(m), DC to 8 GHz, 50 Ω
OSLNF50A-8 High Performance Type N(f), DC to 8 GHz, 50 Ω
2000-1914-R Precision Open/Short/Load, 4.3-10(f), DC to 6 GHz, 50 Ω
2000-1915-R Precision Open/Short/Load, 4.3-10(m), DC to 6 GHz, 50 Ω
2000-1618-R Precision Open/Short/Load, 7/16 DIN(m), DC to 6.0 GHz 50
2000-1619-R Precision Open/Short/Load, 7/16 DIN(f), DC to 6.0 GHz 50
22N50 Open/Short, N(m), DC to 18 GHz, 50
22NF50 Open/Short, N(f), DC to 18 GHz, 50
SM/PL-1 Precision Load, N(m), 42 dB, 6.0 GHz
SM/PLNF-1 Precision Load, N(f), 42 dB, 6.0 GHz
Part Number Description
22N75 Open/Short, N(m), DC to 3 GHz, 75 Ω
22NF75 Open/Short, N(f), DC to 3 GHz, 75 Ω
26N75A Precision Termination, N(m), DC to 3 GHz, 75 Ω
26NF75A Precision Termination, N(f), DC to 3 GHz, 75 Ω
12N50-75B
Matching Pad, DC to 3 GHz, 50 Ω to 75 Ω
Ω
Ω
Ω
Ω
MT8220T TDSPN: 11410-00698 Rev. AP27 of 32
MT8220TSpecifications
Precision Adapters
Part Number Description
34NN50A N(m) to N(m), DC to 18 GHz, 50 Ω
34NFNF50 N(f) to N(f), DC to 18 GHz, 50 Ω
Adapters
Part Number Description
1091-26-R DC to 18 GHz, N(m) to SMA(m), 50 Ω
1091-27-R DC to 18 GHz, N(m) to SMA(f), 50 Ω
1091-80-R DC to 18 GHz, N(f) to SMA(m), 50 Ω
1091-81-R DC to 18 GHz, N(f) to SMA(f), 50 Ω
1091-172-R DC to 1.3 GHz, N(m) to BNC(f), 50 Ω
1091-465-R DC to 6 GHz, 4.3-10(f) to N(f), 50 Ω
1091-467-R DC to 6 GHz, 4.3-10(m) to N(f), 50 Ω
1091-417-R DC to 6 GHz, N(m) to QMA(f), 50 Ω
1091-418-R DC to 18 GHz, N(m) to QMA(m), 50 Ω
510-90-R DC to 7.5 GHz, 7/16 DIN(f) to N(m), 50 Ω
510-91-R DC to 7.5 GHz, 7/16 DIN(f) to N(f), 50 Ω
510-92-R DC to 7.5 GHz, 7/16 DIN(m) to N(m), 50 Ω
510-93-R 7/16 DIN(m) to N(f), DC to 7.5 GHz, 50 Ω
510-96-R DC to 7.5 GHz, 7/16 DIN(m) to 7/16 DIN (m), 50 Ω
510-97-R DC to 7.5 GHz, 7/16 DIN(f) to 7/16 DIN (f), 50 Ω
510-102-R DC to 11 GHz, N(m)-N(m), 90 degrees, 50 Ω
InterChangeable Adaptor Phase Stable Test Port Cables, Armored w/Reinforced Grip
sweep applications. It uses the same ruggedized grip as the Reinforced grip series cables. Now you can also change the adaptor interface on the grip to
four different connector types)
Part Number Description
15RCN50-1.5-R 1.5 m, DC to 6 GHz, N(m), N(f), 7/16 DIN(m), 7/16 DIN(f), 50 Ω
15RCN50-3.0-R 3.0 m, DC to 6 GHz, N(m), N(f), 7/16 DIN(m), 7/16 DIN(f), 50 Ω
(recommended for cable and antenna line
Phase-Stable Test Port Cables, Armored w/ Reinforced Grip
Part Number Description
15RNFN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to N(f), 50 Ω
15RDFN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω
15RDN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω
15RNFN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to N(f), 50 Ω
15RDFN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω
15RDN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω
Phase-Stable Test Port Cables, Armored
(ideal for use with tightly spaced connectors and other general use applications)
Part Number Description
15NNF50-1.5C 1.5 m, DC to 6 GHz, N(m) to N(f), 50 Ω
15NN50-1.5C 1.5 m, DC to 6 GHz, N(m) to N(m), 50 Ω
15NDF50-1.5C 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω
15ND50-1.5C 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω
15NNF50-3.0C 3.0 m, DC to 6 GHz, N(m) to N(f), 50 Ω
15NN50-3.0C 3.0 m, DC to 6 GHz, N(m) to N(m), 50 Ω
15NNF50-5.0C 5.0 m, DC to 6 GHz, N(m) to N(f), 50 Ω
15NN50-5.0C 5.0 m, DC to 6 GHz, N(m) to N(m), 50 Ω
15N43M50-1.5C
15N43F50-1.5C
15N43M50-3.0C
15N43F50-3.0C
(Recommended for cable & antenna line sweep applications)
Test Port Extension Cable, Armored, 1.5 meters,
DC to 6GHz, N(m) to 4.3-10(m)
Test Port Extension Cable, Armored, 1.5 meter,
DC to 6GHz, N(m) to 4.3-10(f)
Test Port Extension Cable, Armored, 3 meters,
DC to 6 GHz, N(m) to 4.3-10(m)
Test Port Extension Cable, Armored, 3 meters,
DC to 6 GHz, N(m) to 4.3-10(f)
28 of 32PN: 11410-00698 Rev. APMT8220T TDS
SpecificationsMT8220T
GPS Antennas
(active)
Directional Antennas
Portable Antennas
Part Number Description
2000-1528-R Magnet Mount, SMA(m) with 5 m (16.4 ft) cable, requires 5 VDC
2000-1652-R Magnet Mount, SMA(m) with 0.3 m (1 ft) cable, requires 3.3 VDC or 5 VDC
2000-1760-R Miniature Antenna, SMA(m), requires 2.5 VDC to 3.7 VDC
Part Number Description
2000-1411-R 824 MHz to 896 MHz, N(f), 12.3 dBi, Yagi
2000-1412-R 885 MHz to 975 MHz, N(f), 12.6 dBi, Yagi
2000-1413-R 1710 MHz to 1880 MHz, N(f), 12.3 dBi. Yagi
2000-1414-R 1850 MHz to 1990 MHz, N(f), 11.4 dBi, Yagi
2000-1415-R 2400 MHz to 2500 MHz, N(f), 14.1 dBi, Yagi
2000-1416-R 1920 MHz to 2170 MHz, N(f), 14.3 dBi, Yagi
2000-1659-R 698 MHz to 787 MHz, N(f), 10.1 dBi, Yagi
2000-1660-R 1425 MHz to 1535 MHz, N(f), 14.3 dBi, Yagi
2000-1715-R Directional Antenna, 698 MHz to 2500 MHz, N(f), gain of 2 dBi to 10 dBi,
2000-1616-R 20 MHz to 21000 MHz, N(f), 50 Ω
2000-1645-R 694 MHz to 894 MHz, 3 dBi peak gain
2000-1646-R 750 MHz to 1250 MHz, 3 dBi peak gain,
2000-1647-R Cable 1: 698 MHz to 1200 MHz, 2 dBi peak gain,
2000-1946-R Cable 1: 617 MHz to 960 MHz, 3 dBi peak gain,
2000-1648-R 1700 MHz to 6000 MHz, 3 dBi peak gain, N(m), 50 Ω, 10 ft
1700 MHz to 2700 MHz, 3 dBi peak gain, N(m), 50 Ω, 10 ft
1650 MHz to 2700 MHz, 5 dBi peak gain
1700 MHz to 2700 MHz, 5 dBi peak gain, N(m), 50 Ω, 10 ft
Cable 2: 3000 MHz to 6000 MHz, 5 dBi peak gain, N(m), 50 Ω, 10 ft
Cable 3: GPS 26 dB gain, SMA(m), 50 Ω, 10 ft
1710 MHz to 3700 MHz, 4 dBi peak gain, N(m), 50 Ω, 10 ft
Cable 2: 3000 MHz to 6000 MHz, 5 dBi peak gain, N(m), 50 Ω, 10 ft
Cable 3: GPS 26 dB gain, SMA(m), 50 Ω, 10 ft
MT8220T TDSPN: 11410-00698 Rev. AP29 of 32
MT8220TSpecifications
Filters
Part Number Description
1030-114-R 806 MHz to 869 MHz, N(m) to SMA(f), 50 Ω
1030-109-R 824 MHz to 849 MHz, N(m) to SMA(f), 50 Ω
1030-110-R 880 MHz to 915 MHz, N(m) to SMA(f), 50 Ω
1030-111-R 1850 MHz to 1910 MHz, N(m) to SMA(f), 50 Ω
1030-112-R 2400 MHz to 2484 MHz, N(m) to SMA(f), 50 Ω
1030-105-R 890 MHz to 915 MHz, N(m) to N(f), 50 Ω
1030-106-R 1710 MHz to 1790 MHz, N(m) to N(f), 50 Ω
1030-107-R 1910 MHz to 1990 MHz, N(m) to N(f), 50 Ω
1030-149-R High Pass, 150 MHz, N(m) to N(f), 50 Ω
1030-150-R High Pass, 400 MHz, N(m) to N(f), 50 Ω
1030-151-R High Pass, 700 MHz, N(m) to N(f), 50 Ω
1030-152-R Low Pass, 200 MHz, N(m) to N(f), 50 Ω
1030-153-R Low Pass, 550 MHz, N(m) to N(f), 50 Ω
1030-155-R 2500 MHz to 2700 MHz, N(m) to N(f), 50 Ω
1030-178-R 1920 MHz to 1980 MHz, N(m) to N(f), 50 Ω
1030-179-R 777 MHz to 798 MHz, N(m) to N(f), 50 Ω
1030-180-R 2500 MHz to 2570 MHz, N(m) to N(f), 50 Ω
2000-1684-R 791 MHz to 821 MHz, N(m) to N(f), 50 Ω
2000-1734-R Bandpass Filter, 699 MHz to 715 MHz, N(m) and N(f), 50 Ω
2000-1735-R Bandpass Filter, 776 MHz to 788 MHz, N(m) and N(f), 50 Ω
2000-1736-R Bandpass Filter, 815 MHz to 850 MHz, N(m) and N(f), 50 Ω
2000-1737-R Bandpass Filter, 1711 MHz to 1756 MHz, N(m) and N(f), 50 Ω
2000-1738-R Bandpass Filter, 1850 MHz to 1910 MHz, N(m) and N(f), 50 Ω
2000-1739-R Bandpass Filter, 880 MHz to 915 MHz, N(m) and N(f), 50 Ω
2000-1740-R Bandpass Filter, 1710 MHz to 1785 MHz, N(m) and N(f), 50 Ω
2000-1741-R Bandpass Filter, 1920 MHz to 1980 MHz, N(m) and N(f), 50 Ω
2000-1742-R Bandpass Filter, 832 MHz to 862 MHz, N(m) and N(f), 50 Ω
2000-1743-R Bandpass Filter, 2500 MHz to 2570 MHz, N(m) and N(f), 50 Ω
2000-1799-R Bandpass Filter, 2305 MHz to 2320 MHz, N(m) and N(f), 50 Ω
2000-1911-R Bandpass Filter, 703 MHz to 748 MHz, N(m) and N(f), 50 Ω
2000-1912-R Bandpass Filter, 788 MHz to 798 MHz, N(m) and N(f), 50 Ω
2000-1925-R Bandpass Filter, 663 MHz to 698 MHz, N(m) and N(f), 50 Ω
2000-1926-R Bandpass Filter, 776 MHz to 806 MHz, N(m) and N(f), 50 Ω
Attenuators
Part Number Description
3-1010-122 20 dB, 5 W, DC to 12.4 GHz, N(m) to N(f)
42N50-20 20 dB, 5 W, DC to 18 GHz, N(m) to N(f)
42N50A-30 30 dB, 50 W, DC to 18 GHz, N(m) to N(f)
3-1010-123 30 dB, 50 W, DC to 8.5 GHz, N(m) to N(f)
1010-127-R 30 dB, 150 W, DC to 3 GHz, N(m) to N(f)
3-1010-124 40 dB, 100 W, DC to 8.5 GHz, N(m) to N(f), Uni-directional
1010-121-R 40 dB, 100 W, DC to 18 GHz, N(m) to N(f), Uni-directional
1010-128-R 40 dB, 150 W, DC to 3 GHz, N(m) to N(f)
30 of 32PN: 11410-00698 Rev. APMT8220T TDS
SpecificationsMT8220T
NEON® MA8100A Signal Mapper
Model Number Description
MA8100A-000 NEON Signal Mapper with Anritsu Integration and Tracking Unit. Includes
MA8100A-001 NEON Signal Mapper with Anritsu Integration and Tracking Unit. Includes
MA8100A-003 NEON Signal Mapper with Anritsu Integration and Tracking Unit. Includes
MA8100A-005 NEON Signal Mapper with Anritsu Integration and Tracking Unit. Includes
MA8100A-100 NEON Signal Mapper with Anritsu Integration and Tracking Unit. Includes
2300-606 Perpetual NEON Software License with 3 years of maintenance and
2300-612 Renewal of 1 year NEON Software License with 1 year of maintenance and
2300-613 Renewal of 3 year NEON Software License with 3 years of maintenance and
2300-614 Renewal of 5 year NEON Software License with 5 years of maintenance and
2000-1852-R NEON Tracking Unit (includes USB cable and belt clip, Worldwide version)
2000-2015-R NEON Tracking Unit (includes USB cable and belt clip, Japan version)
2000-1853-R Belt clip (for NEON Tracking Unit)
1 year NEON Software License with 1 year of maintenance and support
and 1 year of Cloud Service (PN: 2300-607).
1 year NEON Software License with 1 year of maintenance and support
and 1 year of Cloud Service (PN: 2300-574).
3 year NEON Software License with 3 years of maintenance and support
and 3 years of Cloud Service (PN: 2300-575).
5 year NEON Software License with 5 years of maintenance and support
and 5 years of Cloud Service (PN: 2300-576).
Perpetual NEON Software License with 3 years of maintenance and
support and 3 years of Cloud Service (PN: 2300-606).
support and 3 years of Cloud Service. Part number can also be used to
order a perpetual license after a limited term license has expired.
support and 1 year of Cloud Service.
support and 3 years of Cloud Service.
support and 5 years of Cloud Service.
MT8220T TDSPN: 11410-00698 Rev. AP31 of 32
Training at Anritsu
Anritsu has designed courses to help you stay up to date with technologies important to your job. For available training
courses, visit:
www.anritsu.com/training
• United States
Anritsu Americas Sales Company
450 Century Parkway, Suite 190
Allen, TX 75013, U.S.A.
Phone: +1-800-Anritsu (1-800-267-4878)
Room 2701-2705, Tower A
New Caohejing International Business Center
No. 391 Gui Ping Road
Shanghai 200233, P.R. China
Phone: +86-21-6237-0898
Fax: +86-21-6237-0899
• P.R. China (Hong Kong)
Anritsu Company Ltd.
Unit 1006-7, 10/F.
Greenfield Tower, Concordia Plaza
No. 1 Science Museum Road
Tsim Sha Tsui East, Kowloon
Hong Kong, P.R. China
Phone: +852-2301-4980
Fax: +852-2301-3545
• Japan
Anritsu Corporation
8-5, Tamura-cho, Atsugi-shi, Kanagawa, 243-0016
Japan
Phone: +81-46-296-6509
Fax: +81-46-225-8352
• South Korea
Anritsu Corporation, Ltd.
5FL, 235 Pangyoyeok-ro
Bundang-gu, Seongnam-si
Gyeonggi-do 13494, South Korea
Phone: +82-31-696-7750
Fax: +82-31-696-7751
• Australia
Anritsu Pty. Ltd.
Unit 20, 21-35 Ricketts Road
Mount Waverley, Victoria 3149, Australia
Phone: +61-3-9558-8177
Fax: +61-3-9558-8255