Amana AER5830VAS, AER5830VAW, AER5823XAW, AER5823XAS, AER5823XAB Dimension Guide

30" (76.2 cm) Freestanding Electric Range

PRODUCT MODEL NUMBERS

AER3311WA	AER5524XA	AER5830VA
AER5523XA	AER5823XA

Electrical: To properly install your range, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

●Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located on the left side frame behind the storage drawer panel or behind the top right side of the oven door. Refer to the figures in the “Product Dimensions” section of the “Location Requirements” section.

●This range is manufactured with the neutral terminal connected to the cabinet. Use a 3-wire, UL listed, 40or 50-amp power supply cord (pigtail) (see following Range Rating chart). If local codes do not permit ground through the neutral, use a 4-wire power supply cord rated at 250 volts, 40 or 50 amps and investigated for use with ranges.

Range Rating*		Specified Rating of
		Power Supply Cord Kit
		and Circuit Protection
120/240 Volts	120/208 Volts	Amps
8.8 - 16.5 KW	7.8 - 12.5 KW	40 or 50**
16.6 - 22.5 KW	12.6 - 18.5 KW	50

*The NEC calculated load is less than the total connected load listed on the model/serial rating plate.

**If connecting to a 50-amp circuit, use a 50-amp rated cord with kit. For 50-amp rated cord kits, use kits that specify use with a nominal 1³⁄ " (34.9 mm) diameter connection opening.

● A circuit breaker is recommended.

CABINET OPENING DIMENSIONS

PRODUCT DIMENSIONS

A

B

C

F

E

D

A.27³⁄" (70.5 cm) max. depth with handle

B.46⁄" (119.1 cm) overall height (max.) with leveling legs screwed all the way in*

C.36" (91.4 cm) cooktop height (max.) with leveling legs screwed all the way in*

D.29⁄" (75.9 cm) width

E.25⁄" (64.3 cm) depth - back of range to front of cooktop**

F.Model/serial rating plate (located on the left side frame behind storage drawer or right side of frame behind the oven door)

IMPORTANT: Range must be level after installation. Follow the instructions in the “Level Range” section. Using the cooktop as a reference for leveling the range is not recommended.

**Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.

**Front of door and drawer may extend further forward depending on styling.

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

A freestanding range may be installed next to combustible walls with zero clearance.

*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered by not less than ¹⁄ " (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

*24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered by not less than ¹⁄ " (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

A C B

D

E

F

A.13" (33.0 cm) max. upper cabinet depth

B.30" (76.2 cm) min. opening width

C.For minimum clearance to top of cooktop, see NOTE*

D.30¹⁄" (76.5 cm) min. opening width

E.Outlet - 8" (20.3 cm) to 22" (55.9 cm) from either cabinet, 5¹⁄" (14.0 cm) max. from floor

F. Cabinet door or hinges should not extend into the cutout

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. W10403811B
Instructions packed with product. Specifications subject to change without notice.	2/17/12