Alpine i207-WRA, i209-WRA, iLX-207 Owners Manual
EN
9-INCH AUDIO/VIDEO RECEIVER
7-INCH AUDIO/VIDEO RECEIVER
• OWNER’S MANUAL
Please read before using this equipment.
• MODE D’EMPLOI
Veuillez lire avant d’utiliser cet appareil.
i209
iLX-207
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
FR
ES
Thank you for purchasing this Alpine product. Please take a moment to protect your purchase by
registering your product now at the following address: www.alpine-usa.com/registration
You will be informed of product and software updates (if applicable), special promotions, news
about Alpine.
Merci d’avoir acheté ce produit Alpine. Nous vous invitons à consacrer un moment à la protection
de votre achat en enregistrant votre produit dès maintenant à l’adresse suivante :
www.alpine-usa.com/registration
Vous serez tenu informé des mises à jour des produits et des logiciels (le cas échéant), des
promotions spéciales et de l’actualité d’Alpine.
Gracias por adquirir este producto Alpine. Con solo unos pocos pasos podrá proteger su producto,
registrándolo a través de la siguiente dirección: www.alpine-usa.com/registration
Recibirá información sobre nuevos productos y software, promociones especiales y novedades
sobre Alpine.
ALPINE ELECTRONICS OF AMERICA , INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
.
.
.
Designed by ALPINE Japan
68-34732Z13-B
Resistant to Dust and Fresh Water (i209 Only)
IP53 rating Resistant to Dust and Fresh Water. Rated IP53 under IEC standard 60529.
This product has been tested in a controlled, laboratory environment with an IP (Ingress Protection) rating of IP53
under IEC standard 60529, which is an international standard for measuring the level of protection from dust and
fresh water.
IP test condition
Ter ms of Use an d R isk
Disclaimers
The IP rating is a 2-digit code – the first digit indicates the protection level against dust, and the second digit
indicates the protection level against fresh water.
IP53 means protected against dust with limited ingress, and protected against spraying fresh water up to 60
degrees from vertical.
Although this product is rated IP53, it is not impervious to dust or water damage in all situations.
• Dust and water resistance is not permanent; resistance may decrease as a result of normal wear or other
damage to the product.
• Do not expose to sea/salt water, chlorinated water, mud, detergent or other liquids.
• Do not expose to prolonged rain, fog, humidity, temperature changes or other prolonged weather and
environmental conditions. Condensation, moisture or debris may accumulate in the product. Close vehicle
windows, roof and other openings to avoid exposure to the product.
• If the product gets wet, dry thoroughly with a soft cloth.
• Open/close the product nose with care – dust or water may enter the product.
Liquid and dust damage are not covered under warranty.
Failure to install the product as directed in the installation manual may degrade dust and water resistance.
ENGLISH
Contents
Operating Instructions
PRECAUTIONS
IMPORTANT INFORMATION ........................8
WARNING
Points to Observe for Safe Usage ........................8
WARNING ...................................................... 8
CAUTION ..................................................... 10
NOTICE ........................................................ 10
Features
Favorite Function ................................................12
About Swiping the Touch Screen ...................... 12
Switching the Audio Sources Screen to a
Dedicated Screen .............................................13
Getting Started
Location of Controls ...........................................14
Turning Power On or Off ..................................15
Turning the System On ......................................15
Initial System Start-Up ....................................... 15
Adjusting the Volume ......................................... 15
Lowering Volume Quickly ................................. 15
Touch Screen Operation .................................... 16
Switching Sources ................................................ 16
Operating the Function Button on the Audio/
Video Main Screen ..........................................17
About Basic Operation for List Screen .............17
About the Shortcut Setup Screen ...................... 18
Sound Setup Function ..................................... 18
Rear Seat Entertainment Function ................ 19
About the Menu Screen ...................................... 20
Edit Menu ......................................................... 20
About the Indicator Display ..............................21
Opening screen Customization ......................... 21
How to Input Characters and Numbers
(Keypad) ...........................................................22
Favorite Function
Using the Favorite Function .............................. 23
Editing the Favorite Screen ................................23
Registering Items ............................................. 23
Changing Item Names ....................................24
Changing Icons (only the Shortcut Dialing
icons) ............................................................. 24
Changing the Layout ....................................... 24
Deleting Items .................................................. 25
Applying Alpine TuneIt App
Adjusting the sound via the Smartphone ........26
Facebook Notification Function .......................26
Setup
Setup Operation .................................................. 28
Wireless (Bluetooth) Setup
Bluetooth Setup ................................................... 29
Displaying Bluetooth Information ................ 29
Pairing a Bluetooth Device ............................. 29
Hands-free Device Primary/Secondary
Setting ............................................................ 30
iPhone Auto Pairing Setting .......................... 30
Device Setup ......................................................... 30
Setting the Passcode ........................................ 30
Changing the Character Code of the Phone
Book ............................................................... 31
Selecting the Output Speaker ......................... 31
Setting the Microphone Select (iLX-207
only) ............................................................... 31
General Setup
Sound Setup .........................................................32
Setting the Balance/Fader/Rear Speaker/
Subwoofer ..................................................... 32
Setting the Media Xpander (MX HD) ..........33
Equalizer Presets .............................................. 33
Adjusting the Parametric Equalizer Curve
(Dual HD EQ) .............................................. 33
Adjusting the Crossover Settings
(X-Over) ........................................................34
Adjusting the Time Correction (TCR) ......... 35
Setting Defeat ................................................... 35
Setting the Volume for Each Source .............35
Adjusting the Caller Level ..............................35
Adjusting the Microphone Level ................... 35
Adjusting the Ring Tone Level ......................36
3-EN
Volume Setting ................................................36
Setting Audio Mute On/Off while Backing
up ................................................................... 36
Setting the Microphone Effect ....................... 36
Default Sound Settings ................................... 36
About the Crossover ........................................... 36
About Time Correction ...................................... 37
Picture Quality Setup .......................................... 38
Selecting the Visual EQ Mode
(Factory’s setting) ........................................38
Adjusting Brightness ....................................... 38
Adjusting Color of Picture ............................. 38
Adjusting Tint of Picture ............................... 38
Adjusting Image Contrast .............................. 38
Adjusting Picture Quality .............................. 38
Saving and calling the adjusted picture
quality ............................................................ 38
Display/Key Setup ............................................... 39
Screen/Lighting Customize ............................ 39
Switching the Display Color .......................... 39
Switching the Illumination Color (iLX-207
only) ............................................................... 39
Setting the Text Scroll .....................................39
Switching the Artwork Position .................... 39
General Setup ....................................................... 40
Setting the Menu Language ........................... 40
Format settings ................................................40
Setting the Clock Display ............................... 40
Setting the Time ............................................... 40
Setting Daylight Saving Time ........................ 40
About i209/iLX-207 ........................................40
Setting Demo mode to Off/On ...................... 40
Vehicle Setup .......................................................41
Steering wheel Setting ..................................... 41
Installation Setup ............................................. 41
Source Setup
Radio Setup ..........................................................42
Setting the TUNER (FM) Tone Quality
(Tuner Condition) ....................................... 42
Setting the TUNER (FM) Frequency Step ...42
SiriusXM Setup .................................................... 42
Setting the Alert individually for an Artist/
Song/Favorite Team .................................... 42
Setting ON/OFF of all Songs/Artists/Games
Alert ............................................................... 42
Deleting all stored Alert .................................. 42
Setting the Favorite Sports Team Alerts ...... 43
Setting the Parental Lock ................................ 43
Signal Strength Information ..........................43
AUX Setup ........................................................... 44
Setting the Auxiliary (AUX) Name ............... 44
Switching the Visual Input Signal System ... 44
HDMI Setup ........................................................ 44
Setting the Bluetooth Pandora® ......................... 44
Apple CarPlay Setup ........................................... 44
System Setup
Camera Setup ....................................................... 45
Setting the Camera Input ............................... 45
Setting the Camera Signal Input ................... 45
Switching Video Source for Multi View
Camera .......................................................... 45
Adjusting the Rear/Front/Side Camera
Guide ............................................................. 46
Camera Interrupt Setting (Power OFF Mode)
(Rear Camera Only) ....................................47
Setting Multi Camera to On/Off ...................47
Factory System Setup .......................................... 47
Setting the Source Category ........................... 48
Setting the Default Vehicle Screen ................ 48
Setting the Maestro Module ........................... 48
Rear Seat Entertainment Setup ......................... 48
Remote Sensor Setting .................................... 48
External Accessories Setup ................................ 49
Setting the External Audio Processor ........... 49
Setting the HDMI Selector On/Off ............... 49
Setting the External Accessory Control ....... 49
Smartphone Apps Setup ..................................... 49
Apple CarPlay (Optional)
Access to Apple CarPlay .................................... 50
Android Auto (Optional)
What is Android Auto ........................................ 50
Activate Android Auto ....................................... 50
Radio/HD Radio™/RBDS
Radio Basic Operation
Listening to the Radio ........................................ 52
Presetting Stations Manually ............................. 52
Presetting Stations Automatically ..................... 52
Tuning to Preset Stations ................................... 52
Inputting Frequency Directly and Receiving
the Radio Station ............................................. 53
Receiving a Multicast (HD Radio™ Mode
only) .................................................................. 53
4-EN
Selecting the Receivable Program Type (RBDS
FM Radio mode only) ..................................... 53
Forced Analog Mode ..........................................53
Displaying Radio Text (RBDS FM Radio mode
only) .................................................................. 53
Using Ballgame Mode (HD Radio™ Mode
only) .................................................................. 54
About the Feature Logos .................................... 54
USB Flash drive (Optional)
Playback ................................................................ 56
Fast-forwarding/Fast-reversing (USB Video
only) .................................................................. 56
Stopping Playback (USB Video only) .............. 56
Repeat Play ........................................................... 56
Random Play (USB Audio only) ....................... 56
Searching for a Desired Song ............................. 56
Switching Display Modes (During Video File
Play Back) ......................................................... 57
About USB Video format ................................... 57
iPod/iPhone (Optional)
Playback ................................................................ 59
Searching for a Music File .................................. 59
Quick Search Mode ......................................... 59
Full Search Mode ............................................. 59
Alphabet Search Function ................................. 60
Repeat Play ........................................................... 60
Random Play (Shuffle) .......................................60
Pandora® internet radio (optional)
Listening to Pandora® .........................................61
“Thumbs” Feedback ........................................... 62
Searching for a Desired Station ......................... 62
QuickMix ............................................................. 62
Creating a New Station ....................................... 62
Bookmarking a Desired Track or Artist .......... 62
Connecting a Bluetooth Device (Bluetooth
Pandora® Only) ................................................ 63
Disconnecting the Bluetooth Connection ... 63
Changing the connecting Bluetooth
Device ............................................................ 63
SiriusXM Satellite Radio Operation
(Optional)
Receiving Channels with the SiriusXM
Tuner ................................................................. 65
Tuning Channels by Category ........................... 65
Changing the Display .........................................65
Checking the SiriusXM Radio ID Number ..... 65
Storing Channel Presets ..................................... 65
Tuning Channels using Presets ......................... 65
SmartFavorites Functions .................................. 66
TuneStart™ Function ....................................... 66
TuneScan™ Function ....................................... 66
Search Function ................................................... 66
Selecting the Channel Directly .......................... 67
Storing the desired Song/Artist ......................... 67
Receiving and Tuning to an Alert ..................... 67
Replay Function .................................................. 68
Parental Lock Function ...................................... 68
Using Jump Memory and Jump Recall
function ............................................................. 68
HDMI Device (Optional)
About HDMI selector (Optional) ................. 69
DVD Player Operation
DVD Player SETUP ............................................ 69
CD/MP3/WMA/AAC/WAV
Playback ................................................................ 70
Stopping Playback ............................................... 70
Repeat Play ........................................................... 70
MIX (Random Play) ........................................... 70
File/Folder Name Search (Concerning MP3/
WMA/AAC/WAV) ......................................... 70
Selecting Folders (Concerning MP3/WMA/
AAC/WAV) ..................................................... 70
Info Mode Function ............................................ 70
DVD
Playing a Disc .................................................... 72
If a Menu Screen Appears .............................. 72
Numeric Keypad Input Operations ............. 73
Displaying the Top Menu Screen ................. 73
Displaying the Menu Screen ........................ 73
Playing Still Frames (Pausing) ........................ 73
5-EN
Stopping Playback ............................................. 73
Fast-forwarding/Fast-reversing ...................... 73
Finding the Beginnings of Chapters/Tracks/
Files .................................................................. 73
Forward/Reverse frame-by-frame
Playback .......................................................... 74
Repeat Playback ................................................. 74
Searching by Title Number ............................... 74
Searching Directly by Chapter Number ......... 74
Switching the Angle ...........................................74
Switching the Audio Tracks ............................ 75
Switching the Subtitles (Subtitle Language) ...75
Info Mode Function ............................................ 75
Switching Display Modes ................................... 75
HDMI Operation
Bluetooth Operation
Setup Before Using .............................................. 76
About Bluetooth .............................................. 76
About the Hands-free Phone ......................... 76
Before Using Bluetooth .................................. 76
Hands-free Phone Control
Answering a Call .................................................77
Hanging up the Telephone ................................77
Call Waiting Function ........................................ 77
Calling ................................................................... 78
Calling by Favorite Function .........................78
Making a phone call using the Phone
Menu ............................................................. 78
Using Voice Recognition function ................... 79
Using Siri .......................................................... 79
Voice Dial Function ........................................ 79
Operations During a Conversation ..................80
Adjusting the Speech Volume ....................... 80
Changing the Voice Output ........................... 80
DTMF (Touch-Tone) Function .................... 80
Phone Book Function ......................................... 80
Synchronizing the Phone Book ..................... 80
Adding the Phone Book ................................. 80
Deleting the Phone Book Entries ..................81
Searching in the Phone Book ......................... 81
Bluetooth Audio
Playback ................................................................ 82
Repeat Play ........................................................... 82
Random Play ........................................................ 82
Search Function ................................................... 82
Connecting a Bluetooth Device ........................ 83
Disconnecting the Bluetooth Connection ... 83
Changing the connecting Bluetooth
Device ............................................................ 83
Auxiliary Device (Optional)
Operating Auxiliary Devices (Optional) .......... 84
Operating an AUX, AUX DVD or
GAME ........................................................... 84
Operating an External DVD Player .............. 84
Camera Operation (Optional)
Rear Camera Operation ..................................... 86
Displaying the Rear Camera Image from the
Menu screen ................................................. 86
Displaying the rear view video while the car
is in reverse ................................................... 86
Switching the Image for the Rear Camera ... 86
Guide Display ON/OFF Setting .................... 86
Adjusting the Caution Display Location ...... 87
About the Rear Camera Guide .......................... 87
Front Camera Operation ................................... 88
Displaying the Front Camera image from
the Menu screen. .......................................... 88
Switching the Image Pattern for the Front
Camera .......................................................... 88
About the adjustment of guide display
ON/OFF setting and adjustment of
Caution display location ............................. 89
Side Camera Operation ...................................... 89
Displaying the Side Camera image from the
Menu screen. ................................................ 89
Switching the Image Pattern for the Side
Camera .......................................................... 89
iDataLink Operation
Access to iDataLink Mode ................................. 90
About Parking Sensor screen ......................... 91
External Accessory Control Operation ............ 92
Information
Product Software Update ................................... 93
About the Supported Formats ........................... 93
About MP3/WMA/AAC/FLAC .................... 93
6-EN
In Case of Difficulty ............................................ 95
If this Message Appears ...................................... 96
Specifications ....................................................... 98
LIMITED WARRANTY
7-EN
Operating Instructions
PRECAUTIONS
IMPORTANT INFORMATION
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide more reasonable protection against
harmful interference in a residential installation, and are more
stringent than “outdoor” requirements.
Operation is subjected to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, you are
encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult an experienced radio/TV technician.
WARNING
• Operation of the system while driving is dangerous. Users
should stop vehicle before operating the software.
• Road conditions and regulations take precedence over
information contained on the map display: observe actual
traffic restrictions and circumstances while driving.
• This software is designed for use exclusively in the unit. It
cannot and may not be used in conjunction with other
hardware.
WARNING
This symbol means important instructions. Failure
to heed them can result in serious injury or death.
INSTALL THE PRODUC T CORRECTLY SO THAT THE DRIVER CANNOT WATCH
TV/VIDEO UNLESS THE VEHICLE IS STOPPED AND THE EMERGENC Y
BRAKE IS APPLIED.
It is dangerous for the driver to watch TV/Video while driving a
vehicle. Installing this product incorrectly enables the driver to
watch TV/Video while driving. This may cause a distraction,
preventing the driver from looking ahead, thus causing an accident.
The driver or other people could be severely injured.
DO NOT WATCH VIDEO WHILE DRIVING.
Watching the video may distract the driver from looking ahead of
the vehicle and cause an accident.
WARNING
Points to Observe for Safe Usage
• Read this manual carefully before using this disc and the system
components. They contain instructions on how to use this product
in a safe and effective manner. Alpine cannot be responsible for
problems resulting from failure to observe the instructions in this
manual.
• This manual uses various pictorial displays to show you how to use
this product safely and to alert you to potential dangers resulting
from improper connections and operation. Following are the
meanings of these pictorial displays. It is important to fully
understand the meanings of these pictorial displays in order to use
this manual and the system properly.
• This product may be used with software applications. Please follow
all usage instructions and warnings when using this product at all
times. Do not use this product or any software application in a
manner which will hinder safe operation of your vehicle.
• This product may be used in conjunction with the Alpine KAC-001
External Accessory Control module, which works with various
accessory products manufactured by third parties. Please review
and follow all manufacturer's instructions and warnings for all
accessory products.
8-EN
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY
FROM SAFELY DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be
performed after coming to a complete stop. Always stop the vehicle
in a safe location before performing these functions. Failure to do so
may result in an accident.
DO NOT FOLLOW ROUTE SUGG ESTIONS IF THE NAVIGATION SYSTEM
INSTRUCTS YOU TO PERFORM AN UNSAFE OR ILLEGAL MANEUVER, OR
PLACES YOU IN AN UNSAFE SITUATION OR AREA.
This product is not a substitute for your personal judgement. Any
route suggestions by this system should never supersede any local
traffic regulations or your personal judgement or knowledge of safe
driving practice.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE
NOISES WHILE DRIVING.
Excessive volume levels that obscure sounds such as emergency
vehicle sirens or road warning signals (train crossings, etc.) can be
dangerous and may result in an accident. LISTENING AT LOUD
VOLUME LEVELS IN A CAR MAY ALSO CAUSE HEARING
DAMAGE.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from looking ahead of
the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
KEEP SMALL OBJEC TS SUCH AS SCREWS OUT OF THE REACH OF
CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult
a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire,
electric shock or other injury.
MAKE THE CORREC T CONNECTIONS.
Failure to make the proper connections may result in fire or
product damage.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE
OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY
TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING
OBJECTS.
Arrange wiring and cables in compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct
or hang up on places such as the steering wheel, gear lever, brake
pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions
so as not to contact, damage or obstruct pipes, fuel lines, tanks or
electrical wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO
MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could disable
control of the vehicle and cause fire etc.
9-EN
CAUTION
NOTICE
This symbol means important instructions. Failure
to heed them can result in injury or material
property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the
product. Return it to your authorized Alpine dealer or the nearest
Alpine Service Center for repairing.
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.
Be sure to use only the specified accessory parts. Use of other than
designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP
METAL EDGE.
Route the cables and wiring away from moving parts (like the seat
rails) or sharp or pointed edges. This will prevent crimping and
damage to the wiring. If wiring passes through a hole in metal, use a
rubber grommet to prevent the wire’s insulation from being cut by
the metal edge of the hole.
Product Cleaning
Use a soft dry cloth for periodic cleaning of the product. For more
severe stains, please dampen the cloth with water only. Anything
else has the chance of dissolving the paint or damaging the plastic.
Temperature
Be sure the temperature inside the vehicle is between +45°C
(+113°F) and 0°C (+32°F) before turning your unit on.
Maintenance
If you have problems, do not attempt to repair the unit yourself.
Return it to your Alpine dealer or the nearest Alpine Service Station
for servicing.
Protecting the USB connector
• Only an iPod/iPhone or USB flash drive can be connected to the
USB connector on this unit. Correct performance using other
USB products cannot be guaranteed.
• If the USB connector is used, be sure to use only the supplied
connector cable with the unit. A USB hub is not supported.
• Depending on the connected USB flash drive, the unit may not
function or some functions may not be performed.
• The audio file format that can be played back on the unit is
MP3/WMA/AAC/FLAC.
• Artist/song name, etc., can be displayed. Certain, special
characters may not be correctly displayed.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrate s into this unit may
result in product failure.
10-EN
CAUTION
Alpine accepts no responsibility for lost data, etc., even if data, etc., is
lost while using this product.
On Handling USB Flash drive
• This unit can control a memory storage device that supports the
USB Mass Storage Class (MSC) protocol. Playable audio file
formats are MP3, WMA, AAC and FLAC.
• USB Flash drive function is not guaranteed. Use USB flash drive
according to the terms of agreement. Read the USB flash drive
Owner’s Manual thoroughly.
• Avoid usage or storage in the following locations:
Anywhere in the car exposed to direct sunlight or high
temperatures.
Anywhere the possibility of high humidity or corrosive
substances are present.
• Fix the USB flash drive in a location where driver operation will
not be hindered.
• USB Flash drive may not function correctly at high or low
temperature.
• Use only certified USB flash drive. Note that even certified USB
flash drive, may not function correctly depending on its type or
state.
• Depending on the settings of the USB flash drive type, memory
state or encoding software, the unit may not play back or display
properly.
• USB Flash drive may take time to start playback. If there is a
particular file other than audio in the USB flash drive, it may take
considerable time before the file is played back or searched.
• The unit can play back “mp3,” “wma” or “m4a” file extensions.
• Do not add the above extensions to a file other than audio data.
This non-audio data will not be recognized. The resulting
playback may contain noise that can damage speakers and/or
amplifiers.
• It is recommended to back up important data on a personal
computer.
• Do not remove the USB device while playback is in progress.
Change SOURCE to something other than USB, then remove the
USB device to prevent possible damage to its memory.
• Windows Media and the Windows logo are trademarks, or
registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• Apple, iPhone, iPod, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries. Apple CarPlay is a
trademark of Apple Inc.
• “Made for iPod” and “Made for iPhone” mean that an electronic
accessory has been designed to connect specifically to iPod, or
iPhone, respectively, and has been certified by the developer to
meet Apple performance standards.
• Use of the Apple CarPlay logo means that a vehicle user interface
meets Apple performance standards. Apple is not responsible for
the operation of this vehicle or its compliance with safety and
regulatory standards. Please note that the use of this product
with iPhone, or iPod may affect wireless performance.
• Pandora, the Pandora logo, and the Pandora trade dress are
trademarks or registered trademarks of Pandora Media, Inc.,
used with permission. Pandora is currently available in the U.S.,
Australia and New Zealand.
• HD Radio Technology manufactured under license from iBiquity
Digital Corporation. U.S. and Foreign Patents. For patents see
http://patents.dts.com/. HD Radio and the HD, HD Radio, and
“ARC” logos are registered trademarks or trademarks of iBiquity
Digital Corporation in the United States and/or other countries.
• Sirius, XM and all related marks and logos are trademarks of
Sirius XM Radio Inc. All rights reserved.
• Google, Android, Android Auto, Google Play and other marks
are trademarks of Google Inc.
• The Bluetooth® word mark and logos are registered trademarks
owned by the Bluetooth SIG, Inc. and any use of such marks by
Alpine Electronics, Inc. is under license.
• The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing, LLC in the United States and
other countries.
• MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson. Supply of this product only
conveys a license for private,non-commercial use and does not
convey a license nor imply any right to use this product in any
commercial (i.e. revenue-generation) real time broadcasting
(terrestrial, satellite, cable and/or any other media),
broadcasting/streaming via internet, intranets and/or other
networks or in other electronic content distribution systems,
such as pay-audio or audio-on-demand applications. An
independent license for such use is required. For details, please
visit
http://www.mp3licensing.com
11-EN
Features
The screen design used in the Owner’s Manual may differ from the actual screen.
Favorite Function
Frequently used functions can be easily recalled. For details, see “Favorite Function” (page 23).
Favorite screen example
• Frequently used functions and useful functions can be customized for your convenience.
• You can register up to 54 functions.
• You cannot register a function more than once.
About Swiping the Touch Screen
You can change a screen or a page by swiping the touch screen vertically or horizontally with your finger. For details, see “Touch Screen Operation”
(page 16).
Swipe the display with your finger lightly.
12-EN
Switching the Audio Sources Screen to a Dedicated Screen
You can switch the Audio Sources screen to a dedicated screen by touching the icon on one of the four edges of the screen, or by swiping vertically or
horizontally. For details on how to swipe the screen, see “Touch Screen Operation” (page 16).
• The operation is not available when using Apple CarPlay.
Shortcut Setup Screen (page 18)
You can set the Sound Setup or Rear Seat Entertainment
System.
<Audio Sources Screen>
(USB Audio)
1
Preset button or Quick Search mode Screen
*1 The Search mode differs depending on the audio source. For details, see the operating instructions of the audio source.
*2 The screen also switches by pressing the Menu button.
*
Menu Screen (page 20)
You can make settings on the Menu Screen.
*
2
13-EN
Getting Started
Location of Controls
(NAV) button
Recalls the connected smartphone’s map screen.
Depending on the smartphone, this function may not available.
Remote Sensor
Point the remote control transmitter towards the remote sensor
within a range of 2 meters.
For iLX-207
For i209
Microphone (iLX-207 only)
Used for Hands-free or Voice Control modes.
(Camera) button (i209 only)
Recalls the Camera screen.
Controllable with Remote Control
This unit can be controlled with an optional Alpine remote control.
For details, consult your Alpine dealer. Point the optional remote
control transmitter at the remote control sensor.
About the button descriptions used in this Owner’s
Manual
The buttons found on the face of the unit are expressed in bold
(e.g. MENU). The buttons found on the touch-screen display are
shown in bold within brackets, [ ] (e.g. []).
(AUDIO) button
Displays the Audio/Visual screen. If the Audio/Visual screen is
already displayed, changes the source.
or VOICE button
Depending on the connected smartphone, press to recall Siri
function or voice recognition mode.
/ or / (UP/DOWN) button
Press to adjust the volume.
(Favorite) button
Recalls the Favorite screen.
• Press and hold this button for at least 2 seconds to switch to
the iDataLink mode screen. (When connected to the optional
iDataLink module.)
MENU/ (Power Off ) button
Recalls the Menu screen.
Press and hold this button for at least 5 seconds to turn the
power off.
/ button
Press to seek down/up a station in radio mode or down/up a
track, chapter, etc., in other audio/visual sources.
RESET switch
The system of this unit is reset.
14-EN
Turning Power On or Off
Initial System Start-Up
Some of this unit’s functions cannot be performed while the vehicle is in
motion. Be sure to stop your vehicle in a safe location and apply the
parking brake, before attempting these operations.
1 Turn the ignition key to the ACC or ON position.
The system turns on.
• When turned on, the system displays the last screen that was
displayed before the ignition key was turned off. For example, if
the unit is in radio mode when ignition is tur ned off, it will remain
in radio mode when ignition is turned back on.
2 Press and hold the MENU/ (Power Off) button for at least
5 seconds to turn the power off.
• The unit can be turned on by pressing any button.
• The unit is a precision device. Careful handling of the unit should
provide you with years of trouble-free operation.
Turning the System On
When the system is used for the first time, the language
selection menu is displayed. Swipe the Language list screen
vertically, then touch your choice from the list of 23
languages.
Be sure to press the RESET switch when using the unit for the first time,
after changing the car battery, etc.
1 Turn off the unit power.
2 Press the RESET switch with a ballpoint pen or similar
pointed object.
For iLX-207
RESET switch
For i209
RESET switch
Adjusting the Volume
After selecting the language, the time setting screen is displayed.
Touch [ ] or [ ] of “Hour”, “Minute” to adjust the time, then
touch [OK ] to confirm.
Tou ch [Reset] to reset the time.
• The GPS antenna should be connected before adjusting the time.
• Some of this unit’s functions cannot be performed while the vehicle is in
motion. Be sure to stop your vehicle in a safe location and apply the
parking brake before attempting these operations.
Adjust the volume by pressing / or / .
Volume decreases/increases continuously by pressing and holding
/ or /.
Volume: 0 - 35
Lowering Volume Quickly
Audio Mute function instantly lowers the volume level to 0.
1 Press / or / to display the Volume adjunstment
screen.
2 Touch the speaker icon to activate the MUTE mode and
the speaker icon change to .
The audio level will be 0.
3 Press and hold or button continuously to increase
the volume.
15-EN
Touch Screen Operation
Switching Sources
You can operate the system by using the touch panel on the screen.
• Be sure to touch the onscreen button lightly with the pad of your finger
to avoid scratching the display.
Touch operation
Touch a button or list item on the screen lightly.
• If you touch a button and there is no reaction, remove your finger.
• Onscreen buttons that cannot be operated are dimmed.
Swipe operation
Move your finger lightly with a swipe.
Press the (AUDIO) button to change the source.
Switching sources using the (AUDIO) button
During audio/visual playback, press the (AUDIO) button
repeatedly to switch to the desired source.
Radio USB/iPod*1 Factor y Media (USB/iPod)*2 HDMI*
Pandora*
SiriusXM*
Music/Google Play Music*
*1 When no USB flash drive/iPod/HDMI device/Smartphone/Bluetooth
compatible device/SiriusXM Tuner is connected, this option is not
available. When using Apple CarPlay, some option may not available.
*2 Not displayed when your car does not support the source or “Setting the
Source Category” (page 48) is set to “Aftermarket.” This is also not
displayed when the iDataLink module is not connected.
*3 The name set for “HDMI Setup” (page 44), “Setting the Auxiliary
(AUX) Name” (page 44), is displayed.
*4 When Bluetooth Pandora is set to “Off”, this option is not available.
(page 44)
*5 When AUX is set to “Off,” this option is not available. (page 44)
When the iDataLink module (sold separately) is connected, the
Auxiliary (AUX) mode is not available.
*6 Available when an iPhone 5 or later/Android™ smartphone which
installed Android Auto App is connected.
Switching Sources from the Menu screen
1
Bluetooth Pandora*
2
AUX*
3, 5
Bluetooth Audio*1 Apple CarPlay
6
Radio
1, 4
SiriusXM*1 or Factory
1, 3
1 Press the MENU button.
The menu screen is displayed.
• You can also display the menu screen by touching [] on the
lower part of the Audio source screen or by swiping upward.
The Audio source selecting area
Drag & Drop operation
Touch and hold the desired item, then drag it to its new location by
moving your finger, then release your finger to place the item.
• It is not possible to narrow the screen with two fingers (pinch in) or
spread the screen (pinch out).
2 Touch your desired source in the Audio source selecting
area.
• In the menu screen, you can change the Audio source directly or change
the order in which sources change. For details, see “About the Menu
Screen” (page 20).
16-EN
Operating the Function Button on the Audio/ Video Main Screen
Using the Function button on the Audio/Visual main screen.
To uc h [] to change to the Function mode.
HD Radio main screen example
Function mode
About Basic Operation for List Screen
Basic operations on the Setup list screen and the Search list screen.
How to display on the list screen differs depending on the selected item.
Swipe to the right or left to change to the Function mode.
To close the Function mode, touch [].
• Depending on the Audio source, the Function mode displays from the
beginning.
Switches to the menu screen or the previous screen.
Item select button
Closes the window.
Displays the next list page.
• When the next selection item does not exist, the list item is not
displayed.
Lists items for selection
• When there are more than five list items, the page can be changed
by swiping vertically.
Returns to the list screen of the page that you touched.
• The list screens that can be displayed are up to the 2 previous
pages. If you touch [], you can recall your desired page.
Changes the page of the Item select button above.
• “ ” indicates the total number of pages, “ ” indicates the
location of the current page.
List screen close button
• Touch or swipe to the left on the search screen, etc. to close the list
screen.
17-EN
About the Shortcut Setup Screen
Displaying the Sound Setup screen, or the Shortcut Setup screen of the
Rear Seat Entertainment System screen.
To uc h [] or swipe downward in the Audio source screen.
Sound Setup Function
Tone Adjustment mode
The Sound Setup screen or the Rear Seat Entertainment System
Setup Screen is displayed.
Sound Setup screen (Tone Adjustment mode) example
Button for Display Off *
Displays the registered Bluetooth Device List screen.
• See “Pairing a Bluetooth Device” (page 29).
Touch this or swipe upward to change to the currently
playing source screen.
Displays the Hands-free Device Primary/Secondary setting
screen.
• See “Hands-free Device Primary/Secondary Setting” (page 30).
* Display Off mode
- To cancel Display Off mode, touch the screen or press any button.
- Display Off mode is canceled when the power or ACC is turned off.
- When the gear lever is shifted to the reverse (R) position and the rear
camera is connected, the rear camera image is displayed.
- When a call is received on a Bluetooth-connected phone, the
incoming call screen is displayed.
BASS ENGINE SQ mode
Button for changing the BASS ENGINE SQ mode screen
Balance/Fader Image area*
• To reset to the initial settings (Balance: 0, Fader: 0), touch [].
1
Rear Seat Entertainment Function screen switch button
• When Setting the Rear Seat Entertainment is “Off,” you cannot
change the screen. For details on Rear Seat Entertainment setting,
see “Rear Seat Entertainment Setup” (page 48).
Buttons for switching between Front/Rear when adjusting
Bass/Treble*
Buttons for adjusting Bass Level/Treble Level*
Buttons for adjusting Media Xpander *
Buttons for adjusting Subwoofer Level *
2
3, 4
1, 3
1, 3, 5
Button for changing the Tone Adjustment mode screen
• If changing to the Tone Adjustment mode, BASS ENGINE SQ
mode will be disabled.
Buttons for adjusting the BASS ENGINE Level*
Buttons for selecting the BASS ENGINE type *
*1 You can perform a more detailed set up in “Sound Setup” (page 32).
*2 You cannot switch when Front/Rear Sync in “Adjusting the Parametric
Equalizer Curve (Dual HD EQ)” (page 33) is “On.”
*3 When you switch to the BASS ENGINE SQ mode, the value you have
set is ignored.
*4 When the Defeat setting is “On,” you cannot perform the set up.
*5 If the Subwoofer setting is “Off,” the setting cannot be changed. See
“Turning Subwoofer ON/OFF” (page 32).
4
4
18-EN
Adjusting Bass Level/Treble Level
Bass Level and Treble Level can be set independently set for Front and
Rear speakers by touching [Front] or [Rear].
Setting item:
Bass / Treble
Setting contents:
-14 to +14 (Initial setting: 0)
• When “BASS ENGINE SQ” is selected in the Shortcut Setup, this setting
is disabled.
• Adjustment cannot be performed when Defeat is set to “On.”
• The Bass adjusted setting value is interlinked with Band2 of Dual HD
EQ, and the Treble adjusted setting value is interlinked with Band8.
Setting the BASS ENGINE SQ
Setting the BASS ENGINE Type
Creating the ideal Bass impact for your musical taste using BASS
ENGINE SQ.
Setting contents:
Standard (Initial setting) / Punch / Rich / Mid Bass / Low Bass
Standard: Mild low-end boost with mid-range focus for front-
center staging.
Punch: Mid-bass punched up with mid-range impact.
Rich: Accented highs and mid-bass giving outstanding
balance for all types of music.
Mid Bass: Strong high frequency emphasis with mid-bass boost
for more low-end attack.
Low Bass: Strong, low-bass boost with extended highs for a very
dynamic sound.
Adjusting the BASS ENGINE Level
You can adjust the BASS ENGINE Level.
Setting item:
BASS ENGINE Level
Setting contents:
0 to 6 (Initial s etting: 3)
• The BASS ENGINE Level 0 of the BASS ENGINE SQ is common to all
the types.
About setup when the external power amplifier is
connected
In order to optimize the BASS ENGINE SQ mode, we recommend the
following procedure to set up the power amplifier.
Use your favorite music to make the following amplifier adjustment.
1) Set GAIN of the power amplifier to “MIN.”
2) Set the Crossover Mode Selector switch to “OFF.”
• If the switch has no “OFF” position, set as near as possible to full
range.
3) Set the BASS ENGINE Level to “03.”
4) Play a song of the genre you frequently listen to, and adjust
GAIN of the power amplifier.
Rear Seat Entertainment Function
The Rear Seat Entertainment function independently routes different
sources to the front and the rear side of the car. For example, while
listening to the radio or other audio sources in the front, HDMI can be
enjoyed at the rear with optional rear monitors and headphones.
Rear Seat Entertainment System Setup screen
Button for changing to the Sound Setup screen.
Visual source selection area that is displayed on the Rear
monitor.*
Touch the source icon displayed on the Rear monitor.
Front: The image and sound of the sam e visual source as the unit
are output.
Off: Stops output to the Rear monitor.
Illumination Color button
The color coordination select button of the Rear monitor:
White/Blue/Green/Amber/Red/Purple/Skyblue/Off
(This function is depended on Over Head Monitor)
Plasmacluster air volume adjustment button*
Whenever you touch the button, you can change the air volume.
Off Low Mid High Off
• While the plasmacluster is operating, the indicator is displayed on
Remote Sensor
You can set whether the sensor on Rear monitor receives remote
control operation, or the unit receives it.
*1 The visual source that can be output to the Rear monitor is “HDMI/
DVD,” and “AUX.” When the unit plays back the visual source, you can
only select the same visual source as the unit.
*2 When the Plasmacluster in “Setting the Rear Seat Entertainment
System” (page 48) is set to “Off,” the Plasmacluster air volume
adjustment button is not displayed.
• If the same visual source is being output to both the unit and the Rear
monitor when an incoming/outgoing call is made, the visual/audio
output to the Rear monitor is interrupted temporarily depending on the
source.
If different visual sources are being output to the unit and the Rear
monitor, visual/audio output to the Rear monitor continues without
interrupting playback.
1
2
the Audio source screen.
19-EN
About the Menu Screen
In the menu screen, you can select the audio source and perform various
setups or operations on the unit.
Press the MENU button.
The menu screen is displayed.
• You can also display the menu screen by touching [] on the lower
part of the Audio source screen or by swiping upward.
Setup button
Displays the Setup screen. (page 28)
Phone button*
Displays the Phone menu screen. (page 76)
• Depending on the setting and connected devices, the displayed
icons and orders may differ. Touch to display more icons such
as [Notifications]
[Vehicle Info]
*1 Displays when the Camera Select is set to “Front,” “Rear,” or “Other.”
(page 45)
*2 Displays when the Bluetooth setting is set to “On.” (page 29)
*3 Use to display the Facebook Notification List on the connected
smartphone via this unit. (page 27)
Displays when Alpine TuneIt App is set to “USB (iPhone)” or
“Bluetooth (Android),” and when a smartphone with Alpine TuneIt
App installed is connected. (page 26)
*4 Displays the Android Auto screen, displayed when an Android
Smartphone installed Android Auto App is connected. (page 50)
*5 Displays the Apple CarPlay screen, displayed when Apple CarPlay is
turned on and an iPhone 5 or later is connected. (page 50)
*6 Displays the iDataLink mode screen. (page 90)
2
3
*
, [Android Auto]*4, [Apple CarPlay]*5 and
6
*
.
Menu screen example
Displays the currently playing audio source.
Displays the total number of the audio sources that can be
selected. Also displays the current position, counting from
the leftmost audio source.
Touch or swipe downward to return to the Audio source
screen.
Audio source select area
Touch your desired source icon to change the audio source.
• Swiping to the right or left in the Audio source select area, you can
change one audio source at a time. Moreover, swiping to the right
or left outside the Audio source select area (upper and lower sides),
you can change pages of the Audio source select area.
• The source icon displayed in the Audio source select area is the one
checked on the Edit menu screen. For details on how to display/
hide the source icon, see “Edit Menu” (page 20).
Displays Preset No, and information of the Search mode, etc.,
located in the middle of the Audio source select area.
• Touch the desired preset number or the Search mode to change the
audio source directly.
• The displayed information differs depending on the audio source.
Some sources are not displayed.
Touch to display more icons. (Displayed only when icons’
number over 5.)
External Accessory Control button
Is displayed when the optional External Accessory Control
module is connected and “Setting the External Accessory
Control” is set to “On” (page 49).
• You can operate the external accessories from this unit. For details,
see “External Accessory Control Operation” (page 92).
Camera button*
Displays camera images. (page 86)
1
Edit Menu
You cannot operate the Edit Menu screen while driving.
Your vehicle must be parked with the ignition key in the ACC or ON
position. For details, see “To display the Setup Menu screen” in
“Setup Operation” (page 28).
In the Edit Menu screen, you can change the audio source order or set
the display/hide settings.
1 Touch the desired source icon in the Menu screen for at
least 2 seconds.
A checkbox ( or ) is displayed on the upper left area of the
source icon and switches to the edit mode.
• The source icon displayed in the Edit Menu screen is displayed
only when usable setup and conditions of each Audio source are
fulfilled. For details on setup and conditions of each audio source,
see “Switching Sources” (page 16).
Changing the order of Audio source
Drag and drop the source icon to the desired location.
Hiding/Displaying Audio source
Place a check in the checkbox ( ) to display the Audio source
icon. Uncheck the checkbox ( ) to hide it.
• You cannot hide the icon of a source that is currently playing.
2 To uc h [Done].
The editing content is confirmed, and returns to the menu screen.
• Editing here is reflected in the order of (AUDIO) button touching
and change of the Audio source. (page 16)
20-EN
About the Indicator Display
Opening screen Customization
The Indicator Bar at the bottom of the screen displays various types of
information, like the current time.
Lights up when connected to a Bluetooth compatible
device. (Does not display when connection is set to OFF.)
: Bluetooth connection to audio device
: Bluetooth connection to Hands Free Phone
Blinks while reconnecting.
Indicates the battery level of the connected Bluetooth
device*.
Battery
Level
Icon
This may not be displayed depending on the connected
Bluetooth device. Whenever one battery level decreases, the
alarm sounds.
Indicates the signal strength level of the connected
Bluetooth compatible device*.
Displayed when Bluetooth setting is ON.
0123No Service
Plasmacluster indicator
Indicates the setting value (Low/Mid/High) selected in
“Plasmacluster air volume adjustment.”
The clock display
You can switch between the 12 hour display and 24 hour display
options.
For details of navigation operations, refer to “Setting the Clock
Display” on page 40.
Bluetooth devices Name*
* When you connect two Hands-Free Phones, the information of the
Bluetooth device set to Primary is displayed.
Level 3 Level 2 Level 1 No Battery
You can set a BMP image that is stored on a USB flash drive as the
opening screen.
This setting requires the following image format, folder name and file
name.
Usable file format:
-BMP image
- Image size: 800 × 480 pixels (RGB 24 bit or less/number of color bit:
24, 8, 1 bit)
- Compression format: non-compressed
-Folder name*
-File name*
1
: OPENINGFILE
2
: openingfile.bmp
1 Connect the USB flash drive to the USB extension cable.
A message confirming the opening screen change is displayed.
2 To uc h [OK ].
An update indicator “ (Loading)” is displayed, and update for
the opening screen starts.
3 After the update is complete, the following message is
displayed.*
“The logo has been updated successfully! Please remove Flash
Memory and press OK.”
3
4 After removing the USB flash drive, touch [OK] .
The opening screen setting is complete.
*1 Be sure to save the folder to the first layer of the USB flash drive.
*2 Only one BMP image can be set as the opening screen.
*3 If “Customization failed,” is displayed, touch [OK] and then check that
the folder name, file name and file format are correct.
• Do not perform the following actions during the update.
- Do not turn off the ACC to the car.
- Do not unplug the USB flash drive.
- Do not turn off or operate the unit.
• To return the opening screen to its original image, you must Clear All
Settings. Be careful of this operation, as your other settings are also
initialized. For details, see “Initializing the System” (page 40).
21-EN
How to Input Characters and Numbers (Keypad)
The displayed screens and procedures may vary slightly depending on
the function used, but the basic input method is the same.
Input screen area.
Cursor position alteration switch
Cancel
Keypad mode finishes.
(Delete)
Returns to the previous character and erases it.
Touching here for more than 2 seconds will erase all input
characters.
Input number is confirmed.
Character keypad
Space
Special character selector switch
The Alphanumeric/Special characters/Symbols selection popup
is displayed.
Touch the desired character type.
22-EN
Favorite Function
Using the Favorite Function
This unit enables you to recall functions easily by registering frequently
used items such as the Audio source, the navigation search function, etc.
to the Favorite screen. You can recall any of these items easily.
1 Press the (Favorite) button.
The Favorite screen is displayed.
Favorite screen example
Editing the Favorite Screen
You cannot edit the Favorites screen while driving.
Your vehicle must be parked with the ignition key in the ACC or ON
position. For details, see “To display the Setup Menu screen” in
“Setup Operation” (page 28).
1 To uc h [] (Edit).
A checkbox is displayed on the upper left area of the registration
icon and it changes to Edit mode.
Setting item:
Item registration / Item name change / Icon change / Layout change /
Item deletion
2 After editing is complete, touch [] (Back).
Changes to the Edit screen used for registering items or
changing names.
Favorite registration item
Swipe to the left and right to change the pages. You can add up
to 6 pages.
Indicates the location of the currently displayed Favorite
screen.
Swipe to the left and right to change the pages. You can add up
to 6 pages.
2 Touch your desired Favorite registered item.
The desired item is displayed.
• When making a phone call by choosing shortcut dialing, after the
message of confirmation of outgoing phone calls is displayed, touch
[Call]. For details, see “Calling by Favorite Function” (page 78).
3 After the caption for th e confirmation is displayed, touch
[OK] .
4 Editing is complete and the screen switches to the
Favorite screen.
• If you touch [] (Cancel) while editing, the edits are reset and the
screen returns to the previous Edit screen.
Registering Items
1 To uc h [ ] (Add).
The items to be added (categories) are displayed.
2 Touch the desired item to be added (category).
3 Choose the desired item to be added.
• You can add up to 54 items.
• You cannot register an item more than once.
23-EN
Audio/Visual
[Radio]*1 / [USB/iPod] / [Factory Media (USB/iPod)]*2 / [HDMI/DVD] /
[Pandora] / [Bluetooth Pandora] / [SiriusXM]*
4
/ [Bluetooth Audio] / [Apple CarPlay]*5 / [Android Auto]*
[AUX]*
*1 You can choose the frequency from Preset 1 - 12, registered into each
FM1/FM2/AM band of HD Radio™ or RBDS.
*2 Not displayed when your car does not support the source or “Setting the
Source Category” (page 48) is set to “Aftermarket.” This is also not
displayed when the iDataLink module is not connected.
*3 You can choose a channel registered to Presets 1 - 18.
*4 When “AUX” is selected, the source name set in “Setting the Auxiliary
(AUX) Name” (page 44) is also displayed in the Favorite screen.
When the iDataLink module (sold separately) is connected, the
Auxiliary (AUX) mode is not available.
*5 You can register now playing Apple CarPlay Music or Google Play
Music depending on the connected Smartphone.
• You can also register directly by touching [] in the Audio source
screen.
However, if it is already registered, [] is not displayed.
Phone (Shortcut Dialing)*
You can register the user’s shortcut dialing stored in the Phone Book.
• If multiple phone numbers are stored, select a number you want to
register.
• You can register directly by touching [] of the Contacts list.
(page 76)
• You can change the icon you registered. (page 24)
*6 You can only select Phone when a mobile phone is connected.
For details on how to register a mobile phone and downloading Phone
Book, see “Bluetooth Operation” (page 76).
3
or [Factory SiriusXM]*
6
2, 3
5
Changing Icons (only the Shortcut Dialing icons)
/
You can change the icons of Shortcut Dialing category.
The following example explains how to change the Shortcut Dialing
icon.
1 Touch the icon that you want to change.
The icon list is displayed.
2 Touch the icon you want to change from the icon list.
The icon is changed to the selected icon.
Changing Item Names
1 Touch the text area of the registered item.
The Input User Name screen (Keypad) is displayed.
2 Input the name and touch [OK ].
• For details on how to input characters using the keypad, see “How to
Input Characters and Numbers (Keypad)” (page 22).
24-EN
Changing the Layout
Drag and drop the item to the desired location.
The item location is changed.
• When you move to other pages, switch pages, or when you make a new
page and move to another, drag to the end of the screen, and lift your
finger after the page changes.
Deleting Items
When deleting a selected item
1 Touch the checkbox at the left of the item you want to
delete and place a check ( ) in it.
2 To uc h [ ] (Delete).
The selected item will be deleted.
When deleting all items
To uc h [ ] (Delete All).
All items are deleted.
25-EN
Applying Alpine TuneIt App
This unit’s sound tuning is programmable from a connected
Smartphone. It is also possible to download specific parameters for
cer tain vehi cles from A lpine’s TuneIt d atabase s tored in the Clou d. Using
the Alpine TuneIt App, customized parameters can also be uploaded for
others to share and rate.
Through this unit, it is also possible to receive and respond to
information from Alpine’s Social Network Service (SNS) available
through the connected Smartphone.
The installed Alpine TuneIt App should be launched on the Smartphone
before connection to the head unit.
Alpine TuneIt App, is downloadable from Apple’s App Store; the
Android user can download it from Google Play™. For details, consult
your Alpine dealer.
Before these operations, set TuneIt to USB (iPhone) or Bluetooth
(Android) depending on the connected Smartphone. For details, see
“Smartphone Apps Setup” (page 49).
• The application program and related specifications and data may be
deleted or terminated without notice.
• Some Alpine TuneIt App functions may not be available if the
Smartphone is not in a service area or receives no signal.
• Turn Apple CarPlay to Off before using Alpine TuneIt App. Refer to
“Ap p le Ca rP la y S et up” (p ag e 4 4) .
Adjusting the sound via the Smartphone
After setting the above procedure, you can adjust the unit’s sound
function on the Smartphone.
Notification Incoming screen example
Poster ’s picture and name
Touch here to switch to Facebook screen.
Facebook screen is not displayed while driving.
Read (Stop) button
Touch to TTS (Text To Speech) play received notification
(Depending on the status, operation may not be available).
During TTS play mode, touch [Stop] to stop play.
Like button
For “Like” operation. (Valid when Wall Posts or Comments is
received)
Notifications button
Touch to switch to Notifications List screen.
Close button
Close the notification screen.
Touch the desired button to operate.
• A new received Notification prompt will last for 15 seconds. If there is
no operation within 15 seconds, the unit will return to normal mode.
• Touching current main screen will close the notification screen.
• Volume adjustment during TT S play can be adjusted by / or /
(0-35). Settings will be reflected at the next TTS reproduction.
• The TTS volume is output via the car’s front right and left speakers.
1 Make sure the unit is powered on.
2 Launch the Alpine TuneIt App on the Smartphone.
Adjust the unit’s sound accordingly on the Smartphone.
• The setting cannot be done on both the Smartphone and this unit at the
same time. While the sound function of this unit is set via Smartphone,
the sound function settings on the unit will be displayed as “Sound APP
Connected.”
• In some situations, such as the unit is powered off or during a call, etc.,
sound setting cannot be done via the Smartphone.
• This function may not be available depending on the paired
Smartphone.
• Please obey all local traffic laws while using this function.
• When “Setting the External Audio Processor” (page 49) is “On,” this
function is not available.
Facebook Notification Function
Some functions may be available in a future version of Alpine TuneIt
App.
• Depending on the paired Smartphone, the following functions may not
be available even though the Alpine TuneIt App version is updated.
Receiving Notification
When the smartphone connected to the unit receives new notifications
from Facebook, the unit emits a notification sound or displays the
notification screen. Set this up in the Alpine TuneIt App settings.
26-EN
Displaying Facebook Screen
During Notification incoming or Notification List screen, you can
switch to Facebook screen.
Facebook screen example
Message content
Poster ’s photo
Close button: Close the Facebook screen.
Touch the poster’s picture and name to switch to the
Facebook screen.
The detailed information of Notification is displayed.
•Touch [] (Back) to return to Notifications List screen.
• Depending on the status, contents of message and photo may not be
displayed.
• In some situations, such as the unit is powered off or during a call, etc.,
Notification of the Smartphone will not be prompted by this unit.
• Facebook screen is not displayed while driving.
Displaying Notification List
You can view the received Notification from Facebook in the
connected Smartphone via this unit.
Notification List screen example
Poster’s Name and Message
Messages are not displayed while driving.
Touch [Read All]/[Stop] to play/stop all Notifications.
• You can switch to the Notification List screen from the Menu screen.
•Touch [] to return to Current screen.
• Depending on the status, some functions may not be available.
• The displayable amount of the Notification list depends on the
connected Smartphone.
27-EN
Setup
Setup Operation
To display the Setup Menu screen:
Your vehicle must be parked with the ignition key in the ACC or ON
position. To do this, follow the procedures below.
1 Bring your vehicle to a complete stop at a safe location.
Engage the parking brake.
2 Release the parking brake. (For safety, release the parking
brake while depressing the foot brake pedal).
3 Engage the parking brake again.
• For automatic transmission vehicles, place the transmission lever in
the Park position.
Now, the locking system for the Setup operation has been released.
Engaging the parking brake can reactivate the Setup Menu, as long as
the car’s ignition has not been turned off. It is not necessary to repeat
the above procedure (1 through 3) of “To display the Setup Menu
screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the Setup Menu screen.”
1 Press the MENU button.
The Menu screen is displayed.
• You can also display the menu screen, by touching [] on the
lower part of the Audio source screen or by swiping upward.
3 Touch the required setting icon on the upper part of the
Setup main screen or swipe the list area vertically, then
touch the setting item.
Setting items:
Wireless: See “Wireless (Bluetooth) Setup” (page 29).
General: See “General Setup” (page 31).
Source: See “Source Setup” (page41).
System: See “System Setup” (page 45).
2 To uc h [Setup].
The Setup main screen is displayed.
28-EN
[Setup] button
Wireless (Bluetooth) Setup
Bluetooth Setup
[Wireless] is selected on the Setup main screen in step 3. See “Setup
Operation” (page 28).
Wireless Setup Menu screen
<Setting items>
Bluetooth
Bluetooth Information*
Set Bluetooth Device*
Hands-free Device Priority*
iPhone Auto Pairing*
Device
Passcode Change
Default Phone Book Format
Phone Speaker
Microphone Select (iLX-207 only)
*1 This setting is only available when “Bluetooth” is set to “On” ( ).
*2 Cannot be adjusted when an iPhone 5 or later/Android smartphone
which installed Android Auto App is connected, and “Bluetooth” is
fixed to “On”.
The following steps 1 to 3 are common to each “Setting
item” of Wireless Setup. See each section for details.
1/2
1/2
1/2
1/2
[Bluetooth] is selected on the Wireless Setup Menu screen in step 1. See
“Wireless (Bluetooth) Setup” (page 29).
You can register and set up Bluetooth compatible devices.
Setting item:
Bluetooth
Setting contents:
Off / On (Initial sett ing)
Off: Bluetooth function is not used. When the phone
function is during using via Apple CarPlay or Android
Auto, you cannot select “Off ”.
On*: Turn ON to begin phone pairing process.
* Turn this setting “On” to automatically connect a registered Bluetooth
device whenever this unit is turned ON. See “Registering the Bluetooth
Device” if no device is registered.
Displaying Bluetooth Information
Make sure the “Bluetooth” setting is “On” ( ).
You can display the Bluetooth device name and device address of this
unit.
Setting item:
Bluetooth Information
Pairing a Bluetooth Device
1 Select the desired item.
2 To switch the setting, touch [], [], [], [], or mark the
checkboxes “Off”( ) or “On”( ).
• If “ ” appears, there is a further hierarchy. Touch the desired
item.
3 To uc h [] to return to the main source screen.
• To return to the previous List screen, touch [] or [] in the
previous page. For details, see “About Basic Operation for List
Screen” (page 17).
Make sure the “Bluetooth” setting is “On” ( ). See “Bluetooth Setup”
(page 29).
Search for Bluetooth compatible devices.
Setting item:
Set Bluetooth Device
1 To uc h [] (Search) of “No Device.”
The Bluetooth devices can be searched are displayed in a list.
29-EN
2 To uc h [] (Audio), [ ] (Hands-free) or [] (Both)
of the device you want to connect from the list.
Audio: Device is used as an Audio device.
Hands-free: Device is used as a Hands Free Device.
Both: Device is used as both an Audio device and Hands Free
Device.
• You can register up to 5 Bluetooth compatible mobile phones.
• You can connect three Bluetooth Devices; two exclusively for
Hands-Free Phone and one exclusively for Bluetooth Audio.
• When you register a Hands-Free Phone for the first time, Primary
is set automatically. When you connect two Hands-Free Phones,
select “Hands-free” or “Both.” You can then set the priority on the
Primary/Secondary setting screen. For details, see “Hands-free
Device Primary/Secondary Setting” (page 30).
3 When the device registration is complete, a message
appears and the device returns to normal mode.
• The Bluetooth registration process differs depending on the device
version and SSP (Simple Secure Pairing). If a 4 or 6 character Passcode
appears on this device, enter the Passcode using the Bluetooth
compatible device.
If a 6 character Passkey appears on this device, make sure the same
passkey is displayed on the Bluetooth compatible device and touch “Yes.”
• If all 5 devices have been registered, you cannot register a 6th device. To
register another device, you need to delete one of the other
5 devices first.
Setting the Bluetooth Device
Select one of 5 paired Bluetooth compatible devices that you previously
registered.
To uc h [] (Audio) or [ ] (Hands free) of the device you
want to connect from the Paired Device list.
Hands-free Device Primary/Secondary Setting
Make sure the “Bluetooth” setting is “On” ( ). See “Bluetooth Setup”
(page 29).
When you connect two Hands-Free Phones, set the priority of the
operation and the setting of incoming-outgoing calls.
Setting item:
Hands-free Devi ce Priority
Setting contents:
Primary / Secondary
Touch the checkbox for Primary/Secondary of the device
names that are registered to the unit to set them.
• When connected to two hands-free phones, operating restrictions apply
to the hands-free phone registered to Secondary. For details, see
“Hands-free Phone Control” (page 76).
iPhone Auto Pairing Setting
Make sure the “Bluetooth” setting is “On” ( ). See “Bluetooth Setup”
(page 29).
When an iPhone is connected via USB and it is not on the Registered
Device list, it will be paired automatically.
Setting item:
iPhone Auto Pairing
Setting contents:
On / Off (Initial setting)
On: Performs iPhone Auto Pairing se tting.
Off: Does not perform iPhone Auto Pairing setting.
• This setting supports iPhones with iOS Ver.5.5 or later.
• When more than 5 Bluetooth devices are registered, Auto Pairing does
not start.
Deleting a Bluetooth Device from the list
You can delete the information of a previously connected Bluetooth
compatible device.
1 To uc h [ ] (Delete) of the Bluetooth compatible device
to delete from the Paired Device list.
2 To uc h [OK ].
•Touching [Cancel] will cancel the setting.
Device Setup
[Device] is selected on the Wireless Setup Menu screen in step 1. See
“Wireless (Bluetooth) Setup” (page 29).
You can make various settings for a Bluetooth compatible device.
Setting the Passcode
You can set the code for connecting with a Bluetooth compatible device.
Setting item:
Passco de Chan ge
1 Enter a 4-digit passcode (old), and then touch [OK].
• The initial number is 0000.
• For details on how to input the numeric keypad, see “Numeric
Keypad Input Operations” (page 73).
2 Enter a 4-digit passcode (new), and then touch [OK] .
30-EN
Loading...