4IPNET EAP300 Users Manual

0 (0)

EAP300 V2.00

Enterprise Access Point

Quick Installation Guide

EAP300 802.11n/a/b/g Enterprise Access Point ENGLISH

Copyright Notice

This document is protected by USA copyright laws and other laws. Besides, the document is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from 4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations.

All rights reserved.

To download up-to-date version, please visit www.4ipnet.com.

Copyright © 4IPNET, INC. All rights reserved.

Quick Installation Guide EAP300 802.11n/a/b/g Enterprise Access Point ENGLISH


FCC Class B Statement:

This equipment has been tested and proven to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

The device contains a low power transmitter which will send out Radio Frequency (RF) signal when transmitting. This equipment complies with FCC RF Radiation Exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

According to FCC 15.407(e), the device is intended to operate in the frequency band of 5.15GHz to 5.25GHz under all conditions of normal operation. Normal operation of this device is restricted to indoor used only to reduce any potential for harmful interference to co-channel MSS operations.

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Copyright © 4IPNET, INC. All rights reserved.

Quick Installation Guide EAP300 802.11n/a/b/g Enterprise Access Point ENGLISH


Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: EAP300

The device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.

Radio: EN 300.328:

Radio: EN 301 893

EMC: EN 301.489-1, EN 301.489-17,

EMC: EN 55022 Class B, EN 55024:+ A1 + A2 including the followings: EN 61000-3-2, EN 61000-3-3.

EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-11

Safety: EN 60950-1 + A11,


This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4IPNET, Inc. The use of software or firmware not provided and supported by 4IPNET, Inc. may result in the equipment no longer being compliant with the regulatory requirements.

This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory authority for compliance.

Taiwan NCC Statement





Copyright © 4IPNET, INC. All rights reserved.


4IPNET EAP300 Users Manual

Quick Installation Guide EAP300 802.11n/a/b/g Enterprise Access Point ENGLISH


4ipnet EAP300 is a high-end 802.11n/a/b/g dual-band MIMO Access Point (AP) with the best price/ performance for enterprise and industrial applications and is compliant with the latest industrial wireless security standards that are required in the tightly secured enterprise network environments. EAP300 makes the wireless communication fast, secure and easy. It supports business grade security such as 802.1X, and Wi-Fi Protected Access (WPA and WPA2). By pushing a purposely built button, the 4ipnet WES feature makes it easy to bridge wireless links of multiple EAP300s for forming wider wireless network coverage. EAP300 also features multiple ESSIDs with VLAN tags; one EAP300 can emulate up to eight Virtual APs, great for enterprise applications, such as separating the traffics of different departments using different ESSIDs. The PoE LAN port can receive power from Power over Ethernet (PoE) device. Its metal case is IP50 anti-dust compliant, which means that EAP300 is well suited to WLAN deployment in industrial environments.

This Quick Installation Guide provides instructions and reference materials for getting started with 4ipnet EAP300.

Package Contents

1.EAP300 x 1

2.Quick Installation Guide x 1

3.CD-ROM (with User’s Manual and QIG) x 1

4.Power Adapter (DC 12V) x 1

5.Cat. 5e Ethernet cable x 1

6.Antenna x 3

It is recommended to keep the original packing material for possible future shipment when repair or maintenance is required. Any returned product should be packed in its original packaging to prevent damage during delivery.

Wired and Wireless Network Layout with EAP300s

Copyright © 4IPNET, INC. All rights reserved.


+ 10 hidden pages