Loading...Owner’s Manual
CRRFTSMRN
P I O F E S S I O H A L
1-1/2 Horsepower (continyous duty)
2.1 Horsepower (maximum developed)
1200 C.F.M.
3450 R.P.M. (no load R.P.M.)
DUST COLLECTOR
Model No. 152.213371
CAUTION:
FOR YOUR OWN SAFETY; Read and foilow all of the Safety and Operating Instructions before Operating this Dust Collector.
Customer Helpline
1-800-897-7709
Please have your Model No. and Serial No. available.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Part No. OR93765
Espanol pg. 25
SECTION |
PAGE |
W a r r a n t y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 2 |
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
2 |
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3 |
Grounding I n s t r u c t i o n s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . 5 |
Specific Safety Instructions for Dust Collectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 6 |
Accessories and A t t a c h m e n t s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . 7 |
Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
8 |
Know Your Dust Collector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1 0 |
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1 1 |
Operating the Dust C o l l e c t o r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 1 5 |
Dust Collector in the S h o p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 1 7 |
M a i n t e n a n c e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 2 0 |
Troubleshooting G u i d e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 2 0 |
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . . 2 1 |
Service I n f o r m a t i o n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 4 8 |
WARRANT £ |
|
ONE-YEAR FULL WARRANTY ON CRAFTSMAN PROFESSIONAL TOOL |
|
If this Craftsman tool fails due to a defect in material or workmanship within one year from the date of purchase, CALL 1 -800-4-MY-HOME® TO ARRANGE FOR FREE REPAIR.
This warranty applies only while this tool is in the United States.
This warranty gives you specific legal rights, and you may also have other rights, which vary, from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 |
06/05 |
PRODUCT SPECIFICATION
Induction Motor |
|
Continuous duty HP |
1-1/2 |
Maximum developed HP |
2.1 |
Amps |
12/6 |
Volts |
120/240 |
Hertz |
60 |
RPM |
3450 R.P.M. |
|
(no load R.P.M.) |
Standard Bag Top |
30 micron |
Standard Bag Bottom |
30 micron |
Collection Hose |
4-inch Flexible Hose |
Maximum C. F. M. |
1200 |
Maximum static pressure |
12 |
in inches of water |
|
Filter Bag capacity |
6 cubic feet |
Collection Bag capacity |
6 cubic feet |
AWARNING
To avoid electrical shock to yourself and damage to the Dust Collector, use proper circuit protection. Do not expose to rain, or use in a damp environment.
The Dust Collector is factory wired for 120V, 60 Hz, operation. Connect to a 120V, 15 amp branch circuit and use a 15 amp time delay fuse or circuit breaker. The electrical circuit cannot have any wire size less than #14. To avoid shock or fire, replace power cord immediately if it is damaged in any way.
GENERAL SAFETY INSTRUCTIONS
Operating a Dust Collector can be dangerous if safety and common sense are ignored. The operator must be familiar with the operation of the tool. Read this manual to understand this Dust Collector. DO NOT operate this Dust Collector if you do not fully understand the limita tions of this tool. DO NOT modify this Dust Collector in any way. REMEMBER: Your personal safety is your responsibility.
BEFORE USING THE DUST COLLECTOR
ikWARNING
To avoid serious injury and damage to the tool, read and follow all of the Safety and Operating Instructions before operating the Dust Collector.
1.READ the entire Owner's Manual. LEARN how to use the tool for its intended applications.
2.GROUND ALL TOOLS. If the tool is supplied with a 3-prong plug, it must be plugged into a 3-contact electrical receptacle. The 3rd prong is used to ground the tool and provide protection against accidental electric shock. DO NOT remove the 3rd prong. See Grounding Instructions.
3.AVOID A DANGEROUS WORKING ENVIRON MENT. DO NOT use electrical tools in a damp environment or expose them to rain.
4.DO NOT use electrical tools in the presence of flammable liquids or gasses.
5.ALWAYS keep the work area clean, well lit, and organized. DO NOT work in an environment with floor surfaces that are slippery from debris, grease, and wax.
6.KEEP VISITORS AND CHILDREN AWAY. DO NOT permit people to be in the immediate work area, especially when the electrical tool is operating.
7.DO NOT FORCE THE TOOL to perform an opera tion for which it was not designed. It will do a safer and higher quality job by only performing operations for which the tool was intended.
8.WEAR PROPER CLOTHING. DO NOT wear loose clothing, gloves, neckties, or jewelry. These items can get caught in the machine during operations and pull the operator into the moving parts. The user must wear a protective cover on their hair, if the hair is long, to prevent it from contacting any moving parts.
9.ALWAYS WEAR EYE PROTECTION. Any power tool can throw debris into the eyes during opera tions, which could cause severe and permanent eye damage. Everyday eyeglasses are NOT safety glasses. ALWAYS Wear Safety Goggles (that comply with ANSI standard Z87.1) when operating power tools. Safety Goggles are available at Sears Retail Stores.
10.ALWAYS WEAR HEARING PROTECTION. Plain cotton is not an acceptable protective device. Hearing equipment should comply with ANSI S3.19 Standards.
11.ALWAYS UNPLUG THE TOOL FROM THE ELEC TRICAL RECEPTACLE when making adjustments, changing parts or performing any maintenance.
12.KEEP PROTECTIVE GUARDS IN PLACE AND IN WORKING ORDER.
13.AVOID ACCIDENTAL STARTING. Make sure that the power switch is in the "OFF" position before plugging in the power cord to the electrical receptacle.
14.REMOVE ALL MAINTENANCE TOOLS from the immediate area prior to turning the tool “ON".
15.USE ONLY RECOMMENDED ACCESSORIES. Use of incorrect or improper accessories could cause serious injury to the operator and cause damage to the tool. If in doubt, check the instruction manual that comes with that particular accessory.
16.NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to the "OFF" position. DO NOT leave the tool until it has come to a complete stop.
17.DO NOT STAND ON A TOOL. Serious injury could result if the tool tips over or you accidentally contact the tool.
18.DO NOT store anything above or near the tool where anyone might try to stand on the tool to reach it.
19.MAINTAIN YOUR BALANCE. DO NOT extend your self over the tool. Wear oil resistant rubber-soled shoes. Keep floor clear of debris, grease, and wax.
20.MAINTAIN TOOLS WITH CARE. Always keep tools clean and in good working order. Keep all blades and tool bits sharp.
21.EACH AND EVERY TIME, CHECK FOR DAM AGED PARTS PRIOR TO USING THE TOOL. Carefully check all guards to see that they operate properly, are not damaged, and perform their intended functions. Check for alignment, binding or breaking of moving parts. A guard or other part that is damaged should be immediately repaired or replaced.
22.CHILDPROOF THE WORKSHOP AREA by remov ing switch keys, unplugging tools from the electrical receptacles, and using padlocks.
23.DO NOT OPERATE TOOL IF UNDER THE INFLU ENCE OF DRUGS OR ALCOHOL.
24.SECURE ALL WORK. When it is possible, use clamps or jigs to secure the work-piece. This is safer than attempting to hold the work-piece with your hands.
25.STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE WHEN OPERATING A POWER TOOL. DO NOT USE A TOOL WHILE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR MEDICATION. A moment of inattention while operating power tools may result in serious personal injury.
26.ALWAYS WEAR A DUST MASK TO PREVENT INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust and asbestos dust. Direct particles away from face and body. Always operate tool in well
ventilated area and provide for proper dust removal. Use dust collection system whenever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breating the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.
27.USE A PROPER EXTENSION CORD IN GOOD CONDITION. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. Please see minimum recom mended gauge for extension cords (AWG) table for correct sizing of an extension cord. If in doubt, use the next heavier gauge.
The smaller the gauge number, the larger diameter of the extension cord. If in doubt of the proper size of an extension cord, use a shorter and thicker cord. An undersized cord will cause a drop in line voltage resulting in a loss of power and overheating. USE ONLY A 3-WIRE EXTENSION CORD THAT HAS A 3-PRONG GROUNDING PLUG AND A 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL'S PLUG.
GUIDELINES FOR
EXTENSION CORDS
If you are using an extension cord outdoors, be sure it is marked with the suffix "W-A" ("W" in Canada) to indicate that it is acceptable for outdoor use.
Be sure your extension cord is properly sized, and
in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
MINIMUM RECOMMENDED GAUGE FOR EXTENSION CORDS (AWG)
120 VOLT OPERATION ONLY
|
25’ LONG |
50’ LONG |
100’ LONG |
0 to 6 Amps |
|
|
|
18 AWG |
16 AWG |
16 AWG |
|
6 to 10 Amps |
18 AWG |
16 AWG |
14 AWG |
10 to 12 Amps |
16 AWG |
16 AWG |
14 AWG |
|
|
|
|
|
240 VOLT OPERATION ONLY |
|
|
|
|
|
|
|
25’ LONG |
50’ LONG |
100’ LONG |
|
|
|
|
0 to 6 Amps |
18AWG |
18 AWG |
16 AWG |
6 to 10 Amps |
18 AWG |
18 AWG |
14 AWG |
10 to 12 Amps |
16 AWG |
16 AWG |
14 AWG |
|
|
|
|
AWARNING
THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.
IN THE EVENT OF A MALFUNCTION OR BREAK DOWN, grounding provides the path of least resistance for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment-grounding conductor and a ground ing plug. The plug MUST be plugged into a matching electrical receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the electrical receptacle, have the proper electrical receptacle installed by a qualified electrician.
IMPROPER ELECTRICAL CONNECTION of the equip ment-grounding conductor can result in risk of electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment-grounding conductor. DO NOT connect the equipment-grounding conductor to a live terminal if repair or replacement of the electric cord or plug is necessary.
CHECK with a qualified electrician or service personnel if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded.
The motor supplied with your Dust Collector is a dual voltage 120/240 volt, single-phase motor. It is shipped wired for 120-volt application. Never connect the green wire to a live terminal. See OPERATING DUST COLLECTOR section for directions on changing motor voltage.
USE ONLY A 3-WIRE EXTENSION CORD THAT HAS A 3-PRONG GROUNDING PLUG AND A 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL'S PLUG.
REPLACE A DAMAGED OR WORN CORD IMMEDI ATELY.
This tool is intended for use on a circuit that has an electrical receptacle as shown in FIGURE 1. FIGURE 1 shows a 3-wire electrical plug and electrical receptacle that has a grounding conductor. If a properly grounded electrical receptacle is not available, an adapter as shown in FIGURE 2 can be used to temporarily connect this plug to a 2-contact ungrounded receptacle. The adapter has a rigid lug extending from it that MUST be connected to a permanent earth ground, such as a properly grounded receptacle box. THIS ADAPTER IS PROHIBITED IN CANADA.
A tool with a 240-volt plug should only be connected to an outlet having the same configuration as the plug shown in FIGURE 3. No adapter is available or should be used with the 240-volt plug.
CAUTION: In all cases, make certain the electrical receptacle in question is properly grounded. If you are not sure have a certified electrician check the electrical receptacle.
AWARNING
This Dust Collector is for indoor use only. Do not expose to rain or use in damp locations.
SPECIFIC SAFETY INSTRUCTIONS FOR DUST COLLECTORS
The operation of any Dust Collector can result in debris being thrown into your eyes, which can result in severe eye damage. ALWAYS Wear Safety Goggles (that com ply with ANSI standard Z87.1) when operating the Dust Collector. Safety Goggles are available at Sears Retail Stores. Keep your thumbs and fingers away from intake ports.
Basic precautions should always be followed when using your dust collector. To reduce the risk of injury, electrical shock or fire, comply with the safety rules listed below:
1.READ and understand the instruction manual before operating the dust collector.
2.DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instruc tions.
3.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.
4.DO NOT leave the dust collector plugged into the electrical outlet Unplug dust collector from the out let when not in use and before servicing, changing bags, unclogging and cleaning.
5.ALWAYS turn the power switch "OFF" before unplugging the dust collector.
6.TO REDUCE THE RISK OF ELECTRICAL SHOCK, do not use outdoors. Do not expose to rain. Store indoors. Use only for dry pick up.
7.FOLLOW all electrical and safety codes, including the National Electric Code (NEC) and the Occu pational Safety and Health Regulations (OSHA). All electrical connections and wiring should be made by qualified personnel only.
8.DO NOT handle the plug or dust collector with wet hands.
9.DO NOT use the dust collector to pick up flam mable or combustible liquids, such as gasoline. NEVER use the dust collector near any flammable or combustible liquids.
10.USE the dust collector to pick up wood materials only. DO NOT use the dust collector to pick up metal shavings, metal dust, or parts.
11.NEVER use the dust collector to dissipate fumes or smoke. NEVER pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
12.USE only as described in this manual. USE acces sories only recommended by Sears.
13.DO NOT pull the dust collector by the power cord. NEVER allow the power cord to come in contact with sharp edges, hot surfaces, oil or grease.
14.DO NOT unplug the dust collector by pulling on the power cord. ALWAYS grasp the plug, not the cord.
15.REPLACE a damaged cord immediately. DO NOT use a damaged cord or plug. If the dust collector is not operating properly, or has been damaged, left outdoors or has been in contact with water, return it to a Sears Service Center.
16.DO NOT use the dust collector as a toy. DO NOT use near or around children.
17.DO NOT insert fingers or foreign objects into the dust intake port. Keep hair, loose clothing, fingers, and all body parts away from openings and moving parts of the dust collector.
18.DO NOT use the dust collector without the dust collection bag in place and properly secured.
19.ALWAYS use safety gates or caps to cover dust ports when the dust collector is not in use or mounted to a supporting surface for storage.
20.PERIODICALLY INSPECT dust bag for any cuts, rips or tears. NEVER operate the dust collector with a damaged bag or vacuum hose.
21.The dust collector is designed for home use or light commercial duty ONLY.
22.CONNECT dust collector to a properly grounded outlet only. See grounding instructions.
23.ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201 in the Accident Pre vention Manual for Industrial Operation and also in the Safety Data Sheets provided by the NSC. Please also refer to the American National Stand ards Institute ANSI 01.1 Safety Requirements for Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations.
24.SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct other users.
AVAILABLE ACCESSORIES
Visit your Sears Hardware Department or see the Sears Power and Hand Tool Catalog for the following acces sories.
ITEM |
STOCK NUMBER |
30 micron filter bag (top) |
21379 |
5 micron filter bag (top) |
21380 |
Plastic collection bag (bottom) |
21381 |
4" Diameter X 10' flexible hose |
21372 |
4" Diameter x 25' flexible hose |
21373 |
Various accessory fittings |
See catalog or store |
Sears may recommend other accessories not listed in this manual.
See your nearest Sears Hardware Department or Sears Power and Hand Tool Catalog for other accessories.
Do not use any accessory unless you have completely read the Owner's Manual for that accessory.
AWARNING
Use only accessories recommended for this Dust Collector. Using other accessories may cause serious injury and cause damage to the Dust Collector.
UNPACKING AND CHECKING
CONTENTS (Figure 4 and Figure 5)
This Dust Collector will require a minimal amount of assembly.
Remove all of the parts from the shipping box and lay them on a clean work surface. Compare the items to Figure 4 and Figure 5, verify that all items are account ed for before discarding the shipping box.
A. Blower and motor Assembly
B. 4-inch Hose Clamp
C. 4-inch Diameter Flexible Hose
D. Intake Port
AWARNING
If any parts are missing, do not attempt to plug in the power cord and turn "ON" the Dust Collector. The Dust Collector can only be turned "ON" after all the parts have been obtained and installed correctly.
E.Base
F. Intake Port Caps (2)
G.Drum
Fig. 5
H. Locking Band (2)
I. |
Filter Bag |
HARDWARE NOT SHOWN |
J. |
Collection Bag |
* 5/16-18 X 5/8" Hex Head Screw (20) |
K. |
Upper Support Rod |
* 5/16" Lock Washer (24) |
L. |
Lower Support Rod |
* 5/16-18 Hex Nut (12) |
M. |
6-inch Hose Clamp (2) |
* 5/16" X 7/8" O. D. Flat Washer (6) |
N. |
6-inch Diameter Flexible Hose |
* 1/4-20 X 5/8" Hex Head Screw (8) |
O. |
Drum Support (3) |
* 1/4" Lock Washer (8) |
P. |
Caster Assembly (4) |
* 1/4-20 Hex Nut (8) |
Q. |
U-Bracket |
* M4.2 Sheet Metal Screw (4) |
R. |
Retaining Clip (4) |
|
Fig. 6
A.Filter Bag
B.Collection Bag
C.4-inch Intake Port
D.Intake Port Cap
E.6-inch Flexible Hose
F.Base
G.Support Rod
H.Caster
I.Drum
10
AWARNING
1.DO NOT assemble the Dust Collector until you are sure the tool IS NOT plugged in.
2.DO NOT assemble the Dust Collector until you are sure the power switch is in the "OFF" position.
2.For your own safety, DO NOT connect the machine to the power source until the machine is completely assembled and you read and understand the entire Owner's Manual.
CASTER TO BASE ASSEMBLY
Fig. 7
B
BLOWER AND MOTOR ASSEMBLY TO BASE ASSEMBLY
AWARNING
MAKE CERTAIN THE DUST COLLECTOR IS DISCONNECTED FROM THE POWER SOURCE.
1.Insert threaded rod of caster (A) into the hole located on the underside of base (B) and fasten with 3/8" lock-washer (C) and 3/8-16 hex nut (D). See figure 7.
2.Assemble the remaining three casters to the under side of the base in the same manner.
Turn base (A) right side up. Align the mounting holes at the base of blower and motor assembly (B) with six pre-drilled holes (C) in base and fasten with six 5/16-18 X 5/8" hex head screws (D) and 5/16" lock washer (E). See figure 8.
Fig. 9
Assemble drum support (F) to the two threaded holes in the corner of base with two 5/16-18 x 5/8" hex head screws and 5/16" lock washer (G). NOTE: Do not completely tighten hardware at this time. See figure 9.
Assemble the remaining drum supports to the base in the same manner. NOTE: Do not completely tighten hardware at this time.
11
Assemble U-Bracket (H) to Drum (J). Place a 5/16" lock washer then a 5/16" flat washer onto a 5/1618 X 5/8" hex head screw (K) thru the hole in the U-Bracket and the hole in the drum, thread a 5/16" hex nut onto the hex head screw. Repeat this process for the remaining hole and securely tighten both screws. NOTE: U-Bracket should be mounted to the right side of opening (L) in the drum as shown. See figure 10.
Fig. 11
Align the holes in the drum support with the holes in the drum (M). Place a 5/16" lock washer on a 5/1618 X 5/8" hex head screw, then 5/16" flat washer onto the hex head screw. Insert the hex head screw thru the hole in drum support and drum. Thread a 5/16" hex nut onto the hex head screw and tighten securely. See figure 11. Fasten the remaining drum supports to the drum in the same manner.
Fig. 12
Place one end of 6-inch diameter flexible hose (N) over blower/motor outlet(R). Slide one 6-inch diameter hose clamp (S) down 6-inch flexible hose and tighten hose clamp to blower/motor outlet. See figure 12.
7.Place the other 6-inch hose clamp (T) over the 6-inch flexible hose. Attach the 6-inch flexible hose to the drum inlet (U) and tighten 6-inch hose clamp. See figure 12.
12
Fig. 13
Attach the lower dust bag retaining clip (V) to the dust collector drum. Align both holes (W) in the retaining clip with the two holes In the drum. Insert a 1/4-20 X 5/8" hex head screw through each hole in the retaining clip and drum. Place a 1/4" flat washer and 1/4-20 hex nut onto screw inside of the drum. Repeat this process for the other three retaining clips and tighten all hardware.
See figure 13.
INTAKE PORT TO
BLOWER MOTOR ASSEMBLY
AWARNING
MAKE CERTAIN THE DÜST COLLECTOR DISCONNECTED FROM THE POWER SOURCE.
Fig. 14
B
1.Align the four holes in intake port (A) with the mounting holes in flange (B) of blower and motor assembly and fasten with four M4.2 sheet metal screws (C). See figure 14.
Fig. 15
2.Attach one intake port cap (D) to the intake port (E). The intake port caps must be placed into the intake ports when the intakes are not in use.
See figure 15.
IMPORTANT: When connecting an intake hose to one or both intake ports, DO NOT REMOVE THE INTAKE PORT CAP COLLARS (F) FROM THE INTAKE PORTS. Slide the collar further back when attaching a hose. See figure 15.
FILTER AND COLLECTION BAG TO DRUM ASSEMBLY
AWARNING
MAKE CERTAIN THE DUST COLLECTOR IS DISCONNECTED FROM THE POWER SOURCE.
1.Hook the loop (A) on the top filter bag onto hook
(B) of the upper support rod. See figure 17.
13
Fig. 16
Slide the lower support rod (C) onto the end of the upper support rod (B). Raise the assembled support rod with filter bag attached and place the end of the lower support rod into the holes of the U-bracket (D). The flared end of lower support rod will prevent the rod from sliding through the U-bracket. See figure 16.
3.Insert locking band (E) through all the loops of filter bag (F). Position the open end of the filter bag over the top lip of the drum. Make certain the locking band is positioned in the upper recessed channel of the drum and fasten clamp (G) securely to drum. See figure 17.
Place the second locking band through all the loops of the collection bag, similar to the filter bag.
Place the collection bag over the lower lip of the drum. Pull up on the retaining clips and insert col lection bag underneath each retaining clip. Make certain the locking band is positioned in the lower recessed channel of the drum and fasten clamp securely to drum.
FLEXIBLE HOSE TO
INTAKE PORT ASSEMBLY
A WARNING
MAKE CERTAIN THE DUST COLLECTOR DISCONNECTED FROM THE POWER SOURCE.
IMPORTANT: When connecting an intake hose to one or both intake ports, DO NOT REMOVE THE INTAKE PORT CAPS FROM THE INTAKE PORTS. Slide the collar further back the intake port when attaching a hose.
1.To attach the 4-inch flexible hose to one of the intake ports, pull the intake port cap from the intake port. Slide the collar of the intake port cap further back the intake port and let the cap hang from the intake port.
2.Place 4-inch hose clamp over 4-inch flexible hose. Slide hose over one intake port opened Step 1 above and tighten hose clamp.
3.If you wish to use the second intake port, you should purchase a second 4-inch flexible hose and 4-inch hose clamp and repeat Steps 1 and 2 above.
See your nearest Sears Hardware Department or Sears Power and Hand Tool Catalog for other accessories.
A WARNING
Use only accessories recommended for this Dust Collector. Using other accessories may cause serious injury and cause damage to the Dust Collector.
14
AWARNING
FOR OPERATOR SAFETY, keep fingers and all foreign objects out of the intake ports. The rotating fan inside the blower housing is accessible through the intake ports and is hazardous. Do not wear loose clothing or jewelry. Make certain that each intake port which is not being used or attached to a dust collection system is covered with an intake port cap.
CONNECTING TOOL TO
POWER SOURCE
A separate electrical circuit should be used for your tools. This circuit should not be less than #14 A. W. G. wire and should be protected with a 15-amp time lag fuse. Have a qualified electrician repair or replace dam aged or worn cord immediately. Before connecting the motor to the power line, make certain the switch is in the "OFF" position and be sure that the electric current is of the same characteristics as stamped on the motor nameplate. All line connections should make good con tact. Running on low voltage will damage the motor.
AWARNING
DO NOT EXPOSE THE DUST COLLECTOR TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
START/STOP SWITCH
Fig. 18
The START/STOP switch is located on the side of the motor. To turn the dust collector "ON", push the green start button (A). To turn the dust collector "OFF", push the red stop button (B). See figure 18.
LOCKING SWITCH IN
THE "OFF" POSITION
When the Dust Collector is not in use, the start button can be locked so that it cannot be started. Using a padlock (included) through the holes in the side of the start button.
CIRCUIT BREAKER
Your dust collector motor is supplied with a resettable circuit breaker. It is located on top of the starTstop switch box on the side of the motor. If the motor shuts off or fails to start due to an overload condition, turn the dust collector "OFF," let the motor cool for three to five minutes, and push the reset button on the circuit breaker to reset the breaker. The motor can then be turned on again in the usual manner.
15
Loading...