ZyAIR B-400
11Mbps Wireless LAN
Ethernet Adapter
Quick Installation Guide
ZyAIR B-400 Quick Installation Guide
—
2
—
FCC Warning
The ZyAIR B-400 has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment.
FCC Radiation Exposure Statement
The ZyAIR B-400 complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator &
your body. This equipment must not be co-located or operating in
conjunction with any other antenna or transmitter.
CE Marking Warning
This is a Class B product. In a domestic environment this product may
cause radio interference in which case the user may be required to
take adequate measures.
ZyAIR B-400 Quick Installation Guide
—
3
—
Table of Contents
ZYAIR B-400 FEATURES .................................... 4
PACKAGE CONTENTS ........................................ 5
PHYSICAL DETAILS ...........................................6
HARDWARE INSTALLATION ............................ 8
WIRELESS NAVIGATOR INSTALLATION ....... 9
STARTUP AND LOGIN ...................................... 13
FAQ AND TROUBLESHOOTING..................... 16
ZyAIR B-400 Quick Installation Guide
—
4
—
ZyAIR B-400 Features
LAN Features
DHCP Support – Enable the adapter to act as a DHCP client to
receive an IP address from a DHCP Server in the wired
Ethernet LAN
Built-in 10BaseT LAN Port – Designed to connect the adapter
with any Ethernet-ready device, such as a desktop PC, print
server and network printer/scanner.
Wireless Features
Standard Compliant – The adapter complies with the
IEEE802.11b standard, and it is interoperable with
IEEE802.11b-Compliant Equipment
High speed Wireless Connection – Supports up to 11Mbps
wireless data rate
Data Rate Auto Fall-Back - Provides 11, 5.5, 2 and 1Mbps
wireless data rates. Shifts dynamically to guarantee the
availability and reliability of wireless connections.
Roaming – Provides seamless roaming within the IEEE802.11b
wireless LAN infrastructure
Configuration & Management
Easy to Setup - With the Windows-based Wireless Navigator
Utility, users can easily setup the IP address of the adapter, and
upgrade the firmware.
Easy to Manage – The adapter can be easily configured using
any WEB browser from anywhere on the wired or wireless LAN.
Security
Configuring Protection – Provides password protection to
prevent unauthorized users from changing the configuration.
Wireless LAN Security - Provides 64-bit & 128-bit Wired
Equivalent Privacy (WEP) encryption to protect the wireless
data transmissions.
ZyAIR B-400 Quick Installation Guide
—
5
—
Package Contents
One ZyAIR B-400 11Mbps Wireless LAN Ethernet adapter
One installation CD-ROM (Wireless Navigator Utility & User’s
Manual Included)
One power adapter
One quick installation guide
If any of the above items are damaged or missing, please contact your
dealer immediately.
ZyAIR B-400 Quick Installation Guide
—
6
—
Physical Details
Rear Panel
INIT Button “INIT” means “Initialize”. Pressing the button will
reboot the device and restore the settings to the
factory default settings.
LAN Cable
Selection Switch
X: Crossover: the RJ-45 port Tx and Rx lines are reversed. Use
this setting when using a straight cable connected to a PC or
other Ethernet device. It is also the factory default setting.
II: Straight: Straight: the RJ-45 port Tx and Rx lines are normal.
Use this setting when using a straight cable connected to an
Ethernet device, such as an Ethernet hub/switch.
LAN Connection
Power Input
INIT Button
LAN Cable
Selection Switch
ZyAIR B-400 Quick Installation Guide
—
7
—
LAN Connection Use a standard straight, UTP Ethernet cable (RJ-
45 connector) to attach the PC, hub/switch or
broadband router/modem to this port.
Power Input Only use the power adapter supplied with the
adapter
LED Indications
LED Color Status Description
ON The LAN port is linked.
OFF The LAN port is not linked with any
Ethernet device.
Ethernet Green
Blinking The LAN port is sending or
receiving data.
ON The B-400 is linked with a wireless
LAN device.
OFF No data is forwarding between the
wireless LAN and wired LAN ports.
Wireless Green
Blinking Sending or receiving wireless data.
ZyAIR B-400 Quick Installation Guide
—
8
—
Hardware Installation
The following illustration is an example showing how to install the B400 adapter with a PC. Be sure to use the supplied power adapter.
Note!
The B-400 may also be connected to other
Ethernet-ready devices, such as print servers.
ZyAIR B-400 Quick Installation Guide
—
9
—
Wireless Navigator Installation
The Wireless Navigator Utility is provided to allow users to easily
configure the B-400 adapter using any Windows-based PC. This
section describes procedures for installing the Wireless Navigator
Utility onto the PC.
Note!
Please make sure that the PC already has the
TCP/IP protocol installed. If not, please consult
the Windows help file for assistance with setting
up TCP/IP on the PC.
Note!
If the B-400 adapter is used with a non-PC
Ethernet device such as a print server or game
console, users can still install the Wireless
Navigator in any PC located in the same IP
subnet with the B-400. The utility can locate the
B-400 via both wired and wireless Ethernet
connections for remote management.
Step 1: Insert the installation CD-ROM into the CD-ROM drive. Run
the SETUP.EXE program on the CD-ROM. The following
window will be shown automatically.
ZyAIR B-400 Quick Installation Guide
—
10
—
Step 2: After the InstallShield Wizard preparation is finished, the
following window will be shown. Click the Next button to continue.
Step 3: Type in the User Name and Company Name, and click the
Next button to continue.
ZyAIR B-400 Quick Installation Guide
—
11
—
Step 4: The screen will show the default destination chosen by the
utility. To install the Wireless Navigator in another location,
click the Browse button and select an alternate destination.
Click the Next button when ready to continue. The setup
program will then begin to install the programs into the
destination folder.
Step 5: The screen will show the Program Folder that the utility will
use.
Users may type a name to create a new program folder,
or select one from the existing folder list. Then, click the Next
button to continue.
ZyAIR B-400 Quick Installation Guide
—
12
—
Step 6: The Wireless Navigator has been installed now, and then click
the Finish button to to complete the installation.
To remove the Wireless Navigator, click the Start button, and select
Programs, Wireless Navigator, and Uninstall, and then follow the
instructions on the screen.
ZyAIR B-400 Quick Installation Guide
—
13
—
Startup and Login to the B-400
Follow the procedures below to startup the Wireless Navigator and
locate the B-400 Ethernet adapter.
1. Refer to "Wireless Navigator Installation" to install the Wireless
Navigator.
2. Click Start and select Programs, Wireless Navigator and then
Wireless Navigator. Or, just double-click the Wireless Navigator
icon on the desktop screen.
3. The Wireless Navigator starts up, and searches for adapters
located on the wired and wireless LAN.
ZyAIR B-400 Quick Installation Guide
—
14
—
4. The utility will show the B-400 adapter connected to the PC. Please
change the adapter IP address, and check that the computer IP
address and the adapter IP address are on the same subnet. (From
Admin/set IP address)
Note!
If the B-400 adapter is not shown in the list,
please make sure all the cables are well
connected.
ZyAIR B-400 Quick Installation Guide
—
15
—
5. Double-click on the adapter to access its built-in web server. The
below screen will show. Click the OK button. (The default user
name is “admin” and the default password is “1234”).
6. The below screen will then appear. The B-400’s built-in web server
has been successfully entered, and the user can configure the B-400.
7. For details of how to configure the B-400 adapter, please refer to
the User’s Manual supplied in the CD.
ZyAIR B-400 Quick Installation Guide
—
16
—
FAQ and Troubleshooting
This chapter provides solutions to problems usually encountered
during the installation and operation of the B-400. Please refer to the
following descriptions, and for further assistance, please contact the
dealer.
Q: My PC can’t locate the Wireless Ethernet adapter.
How do I solve the problem?
A: Please follow the procedures below:
Check if the Ethernet cable is well connected.
Check if the IP addresses of the PC and B-400 Wireless
Ethernet adapter both are on the same IP network. If not, the
Wireless Navigator can be used to set up the adapter’s IP
address, or the PC’s IP address can be changed directly.
Q: The B-400 adapter cannot communicate with the
Wireless Access Point. How do I solve the problem?
A: Please follow the procedures below:
Check if the Wireless Navigator utility is available to access the
B-400 first. If not, please go through the procedure of Q1.
Check if the adapter is set to Infrastructure correctly.
Check if the SSID of your adapter is the same as AP’s. If not,
please set it to the same SSID as the access point.
Check if WEP is enabled either in the B-400 adapter or at the
access point. If yes, please make sure that the adapter and the
Wireless Access Point both have the same WEP settings,
ZyAIR B-400 Quick Installation Guide
—
17
—
since the keys must match.
Finally, please check if radio interference is causing a problem;
see if connection is possible when close to the Wireless
Access Point. The connection range can be as short as 100
feet in a poor environment.
Q: The Wireless connection speed is very slow. How
can I improve it?
A: The wireless system will connect at the highest possible speed,
depending on the distance and environment conditions. To obtain the
highest possible connection speed, try to adjust the location of the B400, and its antenna’s direction. If interference is the problem,
changing to another channel (1, 6 or 11) may improve the signal.
Q : How do I access the ZyAIR B-400 if I am using a
MAC or Linux PC, or if I do not have the Wireless
Navigator?
A: The default IP of the ZyAIR B-400 is 192.168.1.11. The web
configurator can be accessed through the web browser directly.
(Note: The host’s IP must be first configured to the same
subnet as the ZyAIR B-400).
Loading...