ZILOG Z8673316PEC, Z8673316PSC, Z8673316SEC, Z8673316SSC, Z8673316VEC Datasheet
...
CP97DZ83300
P R E L I M I N A R Y
1
1
P
RELIMINARY
C
USTOMER
P
ROCUREMENT
S
PECIFICATION
Z86E33/733/E34
Z86E43/743/E44
1
CMOS Z8
®
OTP M
ICROCONTROLLERS
FEATURES
■
Standard Temperature (V
CC
= 3.5V to 5.5V)
■
Extended Temperature (V
CC
= 4.5V to 5.5V)
■
28-Pin DIP/SOIC/PLCC Packages (E33/733/E34)
40-Pin DIP Package (E43/743/E44)
44-Pin PLCC/QFP Packages (E43/743/E44)
■
Software Enabled Watch-Dog Timer (WDT)
■
Push-Pull/Open-Drain Programmable on
Port 0, Port 1, and Port 2
■
Low-Power Consumption: 60 mW
■
Programmable Crystal Oscillator, EPROM Protect,
RAM Protect, Auto Latch Disable, Permanent WDT,
32 KHz Oscillator, and EPROM /Test Mode Disable
■
Fast Instruction Pointer: 0.6 µ s
■
Two Standby Modes: STOP and HALT
■
24/32 Input and Output Lines
■
Digital Inputs CMOS Levels, Schmitt-Triggered
■
Software Programmable Low EMI Mode
■
Two Programmable 8-Bit Counter/Timers Each with a 6Bit Programmable Prescaler
■
Six Vectored, Priority Interrupts from Six Different
Sources
■
Auto Latches
■
Auto Power-On Reset (POR)
■
Two Comparators
■
On-Chip Oscillator that Accepts a Crystal, Ceramic
Resonator, LC, RC, or External Clock Drive
GENERAL DESCRIPTION
The Z86E33/733/E34/E43/743/E44 8-bit CMOS One-Time
Programmable (OTP) microcontrollers are members of
Zilog's Z8
®
single-chip microcontroller family featuring enhanced wake-up circuitry, programmable Watch-Dog Timers, Low Noise EMI options, and easy hardware/software
system expansion capability.
Four basic address spaces support a wide range of memory configurations. The designer has easy access to register mapped peripheral and I/O circuits.
For applications demanding powerful I/O capabilities, the
Z86E33/733/E34 have 24 pins and the Z86E43/743/E44
have 32 pins of dedicated input and output. These lines are
grouped into four ports, eight lines per port, and are configurable under software control to provide timing, status signals, and parallel I/O with or without handshake, and address/data bus for interfacing external memory.
Notes: All Signals with a preceding front slash, "/", are
active Low, e.g., B//W (WORD is active Low); /B/W (BYTE
is active Low, only).
Device
ROM
(KBytes)
RAM*
(Bytes)
I/O
Lines
Speed
(MHz)
Z86E33 4 237 24 16
Z86733 8 237 24 16
Z86E34 16 237 24 16
Z86E43 4 236 32 16
Z86743 8 236 32 16
Z86E44 16 236 32 16
Note: *General-Purpose
Z86E33/733/E34/E43/743/E44
CMOS Z8® OTP Microcontrollers Zilog
2
P R E L I M I N A R Y
CP97DZ83300
Power connections follow conventional descriptions below:
Connection Circuit Device
Power V
CC
V
DD
Ground GND V
SS
Figure 1. Functional Block Diagram
Port 3
Counter/
Timers (2)
Interrupt
Control
T wo Analog
Comparators
Port 2
I/O
(Bit Programmable)
ALU
FLAGS
Machine T iming
&
Instruction Control
Program
Counter
VCC
GND
XTAL
44
Port 0
Output Input
Address or I/O
(Nibble Programmable)
8
Address/Data or I/O
(Byte Programmable)
/AS /DS R//W /RESET
RESET
WDT, POR
Port 1
OTP
Register File
Register
Pointer
(E43/743/E44)
(E43/743/E44 Only)
Z86E33/733/E34/E43/743/E44
Zilog CMOS Z8® OTP Microcontrollers
CP97DZ83300
P R E L I M I N A R Y
3
1
PIN IDENTIFICATION
Figure 2. 40-Pin DIP Pin Configuration
Standard Mode
R//W
P25
P26
P27
P04
P05
P06
P14
P15
P07
VCC
P16
P17
XTAL2
XTAL1
P31
P32
P33
P34
/AS
/DS
P24
P23
P22
P21
P20
P03
P13
P12
GND
P02
P11
P10
P01
P00
P30
P36
P37
P35
/RESET
40
DIP
1
20 21
Table 1. 40-Pin DIP Pin Identification
Standard Mode
Pin # Symbol Function Direction
1 R//W Read/Write Output
2-4 P25-P27 Port 2, Pins 5,6,7 In/Output
5-7 P04-P06 Port 0, Pins 4,5,6 In/Output
8-9 P14-P15 Port 1, Pins 4,5 In/Output
10 P07 Port 0, Pin 7 In/Output
11 V
CC
Power Supply
12-13 P16-P17 Port 1, Pins 6,7 In/Output
14 XTAL2 Crystal Oscillator Output
15 XTAL1 Crystal Oscillator Input
16-18 P31-P33 Port 3, Pins 1,2,3 Input
19 P34 Port 3, Pin 4 Output
20 /AS Address Strobe Output
21 /RESET Reset Input
22 P35 Port 3, Pin 5 Output
23 P37 Port 3, Pin 7 Output
24 P36 Port 3, Pin 6 Output
25 P30 Port 3, Pin 0 Input
26-27 P00-P01 Port 0, Pins 0,1 In/Output
28-29 P10-P11 Port 1, Pins 0,1 In/Output
30 P02 Port 0, Pin 2 In/Output
31 GND Ground
32-33 P12-P13 Port 1, Pins 2,3 In/Output
34 P03 Port 0, Pin 3 In/Output
35-39 P20-P24 Port 2, Pins
0,1,2,3,4
In/Output
40 DS Data Strobe Output
Notes:
Pin Configuration and Identification identical on DIP
and Cerdip Window Lid style packages.
Loading...