MC2100 SERIES
3
2
1
REGULATORY
GUIDE
Zebra reserves the right to make changes to any
product to improve reliability, function, or design.
Zebra does not assume any product liability arising
out of, or in connection with, the application or use of
any product, circuit, or application described herein.
No license is granted, either expressly or by
implication, estoppel, or otherwise under any patent
right or patent, covering or relating to any
combination, system, apparatus, machine,
material, method, or process in which Zebra
products might be used. An implied license exists
only for equipment, circuits, and subsystems
contained in Zebra products.
Warranty
For the complete Zebra hardware product warranty
statement, go to: http://www.zebra.com/warranty.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
© 2017 ZIH Corp and/or its affiliates. All rights
reserved. ZEBRA and the stylized Zebra head are
trademarks of ZIH Corp, registered in many
jurisdictions worldwide. All other trademarks are the
property of their respective owners.
72-155018-05 Rev. A — May 2017
Regulatory Information
This guide applies to the following model numbers:
MC2100 and MC2180.
All Zebra devices are designed to be compliant with
rules and regulations in locations they are sold and
will be labeled as required.
Local language translations are available at the
following website: http://www.zebra.com/support
Any changes or modifications to Zebra equipment,
not expressly approved by Zebra, could void the
user's authority to operate the equipment.
CAUTION Only use Zebra approved and UL
Listed accessories, battery packs and battery
chargers.
Do NOT attempt to charge damp/wet mobile
computers or batteries. All components must
be dry before connecting to an external
power source.
Declared maximum operating temperature: 40°C.
Bluetooth® Wireless Technology
This is an approved Bluetooth product. For more
information or to view the End Product Listing,
please visit http://www.bluetooth.org/tpg/listings.cfm.
Wireless Devices Country
Approvals
Regulatory markings, subject to certification, are
applied to the device signifying the radio(s) is/are
approved for use in the following countries: United
States, Canada, Japan, China, S. Korea, Australia,
and Europe
Please refer to the Zebra Declaration of Conformity
(DoC) for details of other country markings. This is
available at http://www.zebra.com/doc.
Note
includes, Austria, Belgium, Bulgaria, Czech
Republic, Cyprus, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Liechtenstein, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovak Republic, Slovenia,
Spain, Sweden, Switzerland and the United
Kingdom.
1
.
1
: For 2.4GHz or 5GHz Products: Europe
CAUTION Operation of the device without
regulatory approval is illegal.
Country Roaming
This device incorporates the International Roaming
feature (IEEE802.11d) which will ensure the product
operates on the correct channels for the particular
country of use.
Health and Safety
Recommendations
Ergonomic Recommendations
CAUTION In order to avoid or minimize the
potential risk of ergonomic injury follow the
recommendations below. Consult with your
local Health & Safety Manager to ensure that
you are adhering to your company’s safety
programs to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a neutral postures
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy
reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Vehicle Installation
RF signals may affect improperly installed or
inadequately shielded electronic systems in motor
vehicles (including safety systems). Check with the
manufacturer or its representative regarding your
vehicle. You should also consult the manufacturer of
any equipment that has been added to your vehicle.
An air bag inflates with great force. DO NOT place
objects, including either installed or portable wireless
equipment, in the area over the air bag or in the air
bag deployment area. If in-vehicle wireless
equipment is improperly installed and the air bag
inflates, serious injury could result.
Position your device within easy reach. Be able to
access your device without removing your eyes from
the road.
Note: Connection to an alert device that will cause a
vehicle horn to sound or lights to flash, on receipt of
a call on public roads, is not permitted.
IMPORTANT
Before installing or using, check state and local laws
regarding windshield mounting and use of
equipment.
For Safe installation
• Do not put your phone in a location that obstructs
the drivers vision or interferes with the operation
of the Vehicle.
• Do not cover an airbag.
Warnings for Use of Wireless
Devices
Please observe all
usage of wireless devices.
warning notices with regard to the
Potentially Hazardous Atmospheres
- Vehicles Use
You are reminded of the need to observe restrictions
on the use of radio devices in fuel depots, chemical
plants etc. and areas where the air contains
chemicals or particles (such as grain, dust, or metal
powders) and any other area where you would
normally be advised to turn off your vehicle engine.
Potentially Hazardous Atmospheres
- Fixed Installations
You are reminded of the need to observe restrictions
on the use of radio devices in fuel depots, chemical
plants etc. and areas where the air contains
chemicals or particles (such as grain, dust, or metal
powders).
Safety in Aircraft
Switch off your wireless device whenever you are
instructed to do so by airport or airline staff. If your
device offers a 'flight mode' or similar feature,
consult airline staff as to its use in flight.
Safety in Hospitals
Wireless devices transmit radio frequency energy
and may affect medical electrical equipment.
Wireless devices should be switched off wherever
you are requested to do so in hospitals, clinics or
healthcare facilities. These requests are designed to
prevent possible interference with sensitive medical
equipment.
Pacemakers
Pacemaker manufacturers recommended that a
minimum of 15 cm (6 inches) be maintained
between a handheld wireless device and a
pacemaker to avoid potential interference with the
pacemaker. These recommendations are consistent
with independent research and recommendations by
Wireless Technology Research.
Persons with pacemakers:
• Should ALWAYS keep the device more than
15cm (6 inches) from their pacemaker when
turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker
to minimize the potential for interference.
• If you have any reason to suspect that
interference is taking place, turn OFF your
device.
Other Medical Devices
Please consult your physician or the manufacturer of
the medical device, to determine if the operation of
your wireless product may interfere with the medical
device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure - Use Properly
Only operate the device in accordance with the
instructions supplied.
International
The device complies with internationally recognized
standards covering human exposure to
electromagnetic fields from radio devices. For
information on “International” human exposure to
electromagnetic fields refer to the Zebra Declaration
of Conformity (DoC) at http://www.zebra.com/doc.
Europe
Handheld Devices
This device was tested for typical body-worn
operation. Use only Zebra tested and approved beltclips, holsters, and similar accessories to ensure EU
Compliance.
US and Canada
Phones
Use only Zebra tested and approved belt-clips,
holsters, and similar accessories to ensure FCC
Compliance. The use of third-party belt-clips,
holsters, and similar accessories may not comply
with FCC RF exposure compliance requirements,
and should be avoided. The FCC has granted an
Equipment Authorization for these model phones
with all reported SAR levels evaluated as in
compliance with the FCC RF emission guidelines.
SAR information on these model phones is on file
with the FCC and can be found under the Display
Grant section of http://www.fcc.gov/oet/ea/fccid.
Co-located Statement
To comply with FCC RF exposure compliance
requirement, the antenna used for this transmitter
must not be co-located or operating in conjunction
with any other transmitter/antenna except those
already approved in this filing.
Handheld Devices
This device was tested for typical body-worn
operation. Use only Zebra tested and approved beltclips, holsters, and similar accessories to ensure
FCC Compliance. The use of third-party belt-clips,
holsters, and similar accessories may not comply
with FCC RF exposure compliance requirements,
and should be avoided.
Laser Devices
Complies with 21CFR1040.10 & 1040.11 except for
deviations pursuant to Laser Notice NO. 50, dated
June 24, 2007 and IEC/EN 60825-1:2007 and/or
IEC/EN 60825-1:2014.
The laser classification is marked on one of the
labels on the device.
Class 1 Laser devices are not considered to be
hazardous when used for their intended purpose.
The following statement is required to comply with
US and international regulations:
Caution: Use of controls, adjustments or
performance of procedures other than those
specified herein may result in hazardous laser light
exposure.
Class 2 laser scanners use a low power, visible light
diode. As with any very bright light source, such as
the sun, the user should avoid staring directly into
the light beam. Momentary exposure to a Class 2
laser is not known to be harmful.
Scanner Labeling
Labels read:
1. CAUTION - CLASS 2 LASER/LED LIGHT
WHEN OPEN. DO NOT STARE INTO BEAM.
2. LASER/LED LIGHT - DO NOT STARE INTO
BEAM. CLASS 2 LASER/LED PRODUCT.
3. COMPLIES WITH 21CFR1040.10 & 1040.11
EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE NO. 50, DATED JUNE 24, 2007
AND IEC/EN 60825-1:2007 AND/OR IEC/EN
60825-1:2014.
LED Devices
Complies with IEC/EN60825-1:2001 & IEC/
EN62471:2006.
Power Supply
Use ONLY a LISTED, Type no. PWRS-14000
(5.4 VDC, 3 A), or KT -14000 (5.4 VDC, 3 A), direct
plug-in power supply, marked Class 2 or LPS
(IEC60950-1, SELV). Use of alternative Power
Supply will invalidate any approvals given to this unit
and may be dangerous.
Batteries
Taiwan - Recycling
EPA (Environmental
Protection Administration)
requires dry battery
producing or importing firms
of the Waste Disposal Act are required to indicate
the recycling marks on the batteries used in sales,
giveaway or promotion. Contact a qualified
Taiwanese recycler for proper battery disposal.
Battery Information
Use only Zebra approved batteries. Accessories
which have battery charging capability are approved
for use with the following battery models:
• Zebra 82-150612-01 (3.7 Vdc,2400 mAh)
Zebra rechargeable battery packs are designed and
constructed to the highest standards within the
industry.
However, there are limitations to how long a battery
can operate or be stored before needing
replacement. Many factors affect the actual life cycle
of a battery pack, such as heat, cold, harsh
environmental conditions and severe drops.
When batteries are stored over six (6) months, some
irreversible deterioration in overall battery quality
may occur. Store batteries at half of full charge in a
dry, cool place, removed from the equipment to
prevent loss of capacity, rusting of metallic parts and
electrolyte leakage. When storing batteries for one
year or longer, the charge level should be verified at
least once a year and charged to half of full charge.
Replace the battery when a significant loss of run
time is detected.
Standard warranty period for all Zebra batteries is
one year, regardless if the battery was purchased
separately or included as part of the mobile
computer. For more information on Zebra batteries,
please visit: http://www.zebra.com/batterybasics
in accordance with Article 15
Battery Safety Guidelines
(Parts)
(Pb) (Hg)
(Cd)
(PBB) (PBDE )
(Metal Parts)
(Circuit Modules)
(Cables and Cable
Assemblies)
(Plastic and Polymeric
Parts)
(Optics and Optical
Components)
(Batteries)
OOO O O O
OO O OX
OOO O
OO O O OO
O
OX O O OX
OO O O OO
OO
ᴿᇩ⢟䍞
(Cr (VI))
This table was created to comply with China RoHS requirements.
ᵢ㺞Ṳדᦤ6-7Ⲻ㿺ᇐ㕌Ⱦ
2㺞⽰䈛ᴿᇩ⢟䍞൞䈛䜞Ԭᡶᴿൽ䍞ᶆᯏѣⲺ䠅ൽ൞*%7㿺ᇐⲺ䲆䠅
㾷≸ԛсȾ
;㺞⽰䈛ᴿᇩ⢟䍞㠩ቇ൞䈛䜞ԬⲺḆжൽ䍞ᶆᯏѣⲺ䠅䎻࠰*%7㿺ᇐ
Ⲻ䲆䠅㾷≸ȾԷѐ൞↚༺θṯᦤᇔ䱻߫ሯр㺞ѣᢉćhĈⲺᢶᵥഖ䘑
㺂䘑ж↛䈪᱄Ⱦε
• The area in which the units are charged should
be clear of debris and combustible materials or
chemicals. Particular care should be taken where
the device is charged in a non commercial
environment.
• Follow battery usage, storage, and charging
guidelines found in the user's guide.
• Improper battery use may result in a fire,
explosion, or other hazard.
• To charge the mobile device battery, the battery
and charger temperatures must be between
+32ºF and +104ºF (0ºC and +40ºC)
• Do not use incompatible batteries and chargers.
Use of an incompatible battery or charger may
present a risk of fire, explosion, leakage, or other
hazard. If you have any questions about the
compatibility of a battery or a charger, contact
Zebra support.
• To enable authentication of an approved battery,
as required by IEEE1725 clause 10.2.1, all
batteries will carry a hologram. Do not fit any
battery without checking it has the authentication
hologram.
• For devices that utilize a USB port as a charging
source, the device shall only be connected to
products that bear the USB-IF logo or have
completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or
deform, puncture, or shred.
• Severe impact from dropping any batteryoperated device on a hard surface could cause
the battery to overheat.
• Do not short circuit a battery or allow metallic or
conductive objects to contact the battery
terminals.
• Do not modify or remanufacture, attempt to insert
foreign objects into the battery, immerse or
expose to water or other liquids, or expose to
fire, explosion, or other hazard.
• Do not leave or store the equipment in or near
areas that might get very hot, such as in a parked
vehicle or near a radiator or other heat source.
Do not place battery into a microwave oven or
dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly
dispose of used re-chargeable batteries.
• Do not dispose of batteries in fire.
• Seek medical advice immediately if a battery has
been swallowed.
• In the event of a battery leak, do not allow the
liquid to come in contact with the skin or eyes. If
contact has been made, wash the affected area
with large amounts of water and seek medical
advice.
• If you suspect damage to your equipment or
battery, contact Zebra support to arrange for
inspection.
Radio Frequency Interference
Requirements-FCC
Note: This equipment has been
tested and found to comply with
the limits for a Class B digital
FCC rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV
technician for help.
device, pursuant to Part 15 of the
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Radio Frequency Interference
Requirements - Canada
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
Radio Transmitters
This device complies with RSS 210 of Industry
Canada. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210
d'Industrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet
aux deux conditions suivantes: (1) le dispositif ne
doit pas produire de brouillage préjudiciable, et (2)
ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Label Marking: The Term “IC:” before the radio
certification only signifies that Industry Canada
technical specifications were met.
Marking and European
Economic Area (EEA)
Statement of Compliance
MC2100
Zebra hereby declares that this device is in
compliance with all applicable Directives, 2014/30/
EU, 2014/35/EU and 2011/65/EU. The full text of the
EU Declaration of Conformity is available at the
following internet address:
http://www.zebra.com/doc.
MC2180
Zebra hereby declares that this radio equipment is in
compliance with Directives, 2014/53/EU and 2011/
65/EU. The full text of the EU Declaration of
Conformity is available at the following internet
address: www.zebra.com
Japan (VCCI) - Voluntary Control Council for
Interference
Class B ITE
この装置は、情報処理装置等電波障害自主規制協議
会（ＶＣＣＩ）の基準に基づくクラス B 情報技術装
置です。この装置は、家庭環境で使用することを目
的としていますが、この装置がラジオやテレビジョ
ン受信機に近接して使用されると、受信障害を引き
起こすことがあります。 取扱説明書に従って正し
い取り扱いをして下さい。
Korea Warning Statement for Class B ITE
기 종별 사 용 자 안 내 문
B급 기기
( 가정용
방송통신기기
)
Other Countries
Brazil
Declarações Regulamentares para MC2180 - Brazil
Nota: “A marca de certificação se aplica ao
Transceptor, modelo MC2180. Este equipamento
opera em caráter secundário, isto é, não tem direito
a proteção contra interferência prejudicial, mesmo
de estações do mesmo tipo, e não pode causar
interferência a sistemas operando em caráter
primário.”
이 기기는 가정용 (B 급 ) 으로
전자파적합등록을
한 기기로서 주로 가정에서
사용하는 것을 목적
으로 하며, 모든 지역에서 사용할 수
있습니다 .
Para maiores informações sobre ANATEL consulte
o site: www.anatel.gov.br
Chile
“Este equipo cumple con la Resolución No 403 de
2008, de la Subsecretaria de telecomunicaciones,
relativa a radiaciones electromagnéticas.”
China
合格证： Quality Certificate
Евразийский Таможенный Союз
Данный продукт соответствует требованиям
знака EAC.
Mexico
Restrict Frequency Range to: 2.450 - 2.4835 GHz.
South Korean
당해 무선설비 는전파혼 신 가능성이 있으므로 인명
안전과 관련된 서비스는 할 수 없습니다 .
Tai wa n
臺灣
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公
司、商號或使用者均不得擅自變更頻率、加大功率或
變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法
通信；經發現有干擾現象時，應立即停用，並改善至
無干擾時方得繼續使用。
前項合法通信，指依電信規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療
用電波輻射性電機設備之干擾。
Ukraine
This equipment corresponds to requirements of the
Technical Regulation No. 1057, 2008 on restrictions
as to the use of some dangerous substances in
electric and electronic devices.
Thailand
เครื่ องโทรคมนาคมและอปกรณนี้
มี ความสอดคล องตามข อกําหนดของ
กทช .
Waste Electrical and
Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of
their life must be returned to Zebra for recycling. For
information on how to return product, please go to:
http://www.zebra.com/weee
Français : Clients de l'Union Européenne : Tous les
produits en fin de cycle de vie doivent être retournés à
Zebra pour recyclage. Pour de plus amples informations
sur le retour de produits, consultez : http://
www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los
productos deberán entregarse a Zebra al final de su
ciclo de vida para que sean reciclados. Si desea más
información sobre cómo devolver un producto, visite:
http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte
müssen am Ende ihrer Lebensdauer zum Recycling an
Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter http://
www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono
giunti al termine del rispettivo ciclo di vita devono essere
restituiti a Zebra al fine di consentirne il riciclaggio. Per
informazioni sulle modalità di restituzione, visitare il
seguente sito Web: http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no
fim de vida devem ser devolvidos à Zebra para
reciclagem. Para obter informações sobre como
devolver o produto, visite: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten
dienen aan het einde van hun levensduur naar Zebra te
worden teruggezonden voor recycling. Raadpleeg http://
www.zebra.com/weee voor meer informatie over het
terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty
wycofane z eksploatacji nale¿y zwróciæ do firmy Zebra
w celu ich utylizacji. Informacje na temat zwrotu
produktów znajduj¹ siê na stronie internetowej http://
www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je
nutné po skonèení jejich životnosti vrátit spoleènosti
Zebra k recyklaci. Informace o zpùsobu vrácení
produktu najdete na webové stránce: http://
www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea
lõppedes tagastada taaskasutamise eesmärgil Zebra'ile.
Lisainformatsiooni saamiseks toote tagastamise kohta
külastage palun aadressi: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement
terméket a Zebra vállalathoz kell eljuttatni
újrahasznosítás céljából. A termék visszajuttatásának
módjával kapcsolatos tudnivalókért látogasson el a http:/
/www.zebra.com/weee weboldalra.
Slovenski: Za kupce v EU: vsi izdelki se morajo po
poteku življenjske dobe vrniti podjetju Zebra za
reciklažo. Za informacije o vraèilu izdelka obišèite: http://
www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som
uppnått sin livslängd måste returneras till Zebra för
återvinning. Information om hur du returnerar produkten
finns på http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki
tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön,
kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa http://www.zebra.com/
weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til
Zebra til recirkulering, når de er udtjent. Læs
oplysningerne om returnering af produkter på: http://
www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο
τέλος της διάρκειας ζωή ς τους, πρέπει να επιστρέφονται
στην Zebra για ανακύκλωση. Για περισσότερες
πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,
επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee
στο
∆ιαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu
fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati
għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif
għandek tirritorna l-prodott, jekk jogħġbok żur: http://
www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po
poteku življenjske dobe vrniti podjetju Zebra za
reciklažo. Za informacije o vračilu izdelka obiščite: http://
www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky
musia byť po uplynutí doby ich životnosti vrátené
spoločnosti Zebra na recykláciu. Bližšie informácie o
vrátení výrobkov nájdete na: http://www.zebra.com/
weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų
eksploatacijos laikui, turi būti grąžinti utilizuoti į
kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti
gaminį, rasite: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas
mūža beigām ir jānogādā atpakaļ Zebra otrreizējai
pārstrādei. Lai iegū
nogādāšanu Zebra, lūdzu, skatiet: http://
www.zebra.com/weee.
Hrvatski: Za kupce u Europskoj uniji: Svi se proizvodi po
isteku vijeka trajanja moraju vratiti tvrtki Zebra na
recikliranje. Informacije o načinu vraćanja proizvoda
potražite na web-stranici: www.zebra.com/weee.
tu informāciju par produktu
TURKISH WEEE Statement of
Compliance
EEE Yönetmeliğine Uygundur
Software Support
Zebra wants to ensure that customers have the
latest release of entitled software at the time of
product purchase.
To confirm that your Zebra device shipped with the
latest release of entitled software, visit:
www.zebra.com/support. Check for the latest
software from Software Downloads > Product Line/
Product > Go.
If your device does not have the latest entitled
software release as of your product purchase date,
please e-mail a request to Zebra at:
entitlementservices@zebra.com.
You must include the following essential device
information with your request:
• Model number
• Serial number
• Proof of purchase
• Title of the software download you are
requesting.
If it is determined by Zebra that your device is
entitled to the latest software release, you will
receive an e-mail containing a link directing you to a
Zebra Web site to download the appropriate
software.
Service Information
If you have a problem using the equipment, contact
your facility’s Technical or Systems Support. If there
is a problem with the equipment, they will contact the
Zebra Support at: http://www.zebra.com/support.
For the latest version of this guide go to:
http://www.zebra.com/support.
CMM Disclosure
Loading...