Zebra MC17 MC17 Product Reference Guide English

Download

MC17/MC17A/ MC17T/MC17U

PRODUCT REFERENCE GUIDE

MC17/MC17A/MC17T/MC17U

Product Reference Guide

72E-100467-06

Rev. A

April 2015

ii MC17/MC17A/MC17T/MC17U Product Reference Guide

No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.

The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Zebra. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Zebra. The user agrees to maintain Zebra’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.

Zebra reserves the right to make changes to any software or product to improve reliability, function, or design.

Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra, intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Zebra products.

Revision History

Changes to the original manual are listed below:

Change Date Description

-01 Rev. A 08/27/07 Initial release.

-02 Rev. A 11/16/07 Update battery installation procedures.

-03 Rev. A 09/08 Add MC17T configuration specific information.

-04 Rev. A 03/10 Add MC17A support.

-05 Rev. A 01/13 Add MC17U support.

-06 Rev. A 01/2015 Zebra Rebranding

iii

Add note to wait 1 minute before inserting MC17 into cradle after new battery insertion. Add 802.11d information. Add application battery error message information.

iv MC17/MC17A/MC17T/MC17U Product Reference Guide

Revision History.............................................................................................................................. ii

About This Guide

Introduction ..................................................................................................................................... xi

Documentation Set ................................................................................................................... xi

Configurations................................................................................................................................. xii

Software Versions..................................................................................................................... xiii

OEM Software........................................................................................................................... xiii

Fusion Software........................................................................................................................ xiii

Chapter Descriptions ...................................................................................................................... xiv

Notational Conventions................................................................................................................... xv

Related Documents and Software .................................................................................................. xv

Service Information......................................................................................................................... xvi

Chapter 1: Getting Started

Introduction .................................................................................................................................... 1-1

Unpacking ...................................................................................................................................... 1-1

Features ......................................................................................................................................... 1-2

Accessories ................................................................................................................................... 1-4

LED Indicators ............................................................................................................................... 1-5

Keypad ........................................................................................................................................... 1-5

Getting Started ............................................................................................................................... 1-6

Connecting the Battery ................................................................................................................. 1-6

Charging the Battery ................................................................................................................ 1-9

Manual Release of MC17 Series from the Charging Cradle .................................................... 1-10

Software Release of MC17 Series from the Charging Cradle ................................................. 1-11

Starting the MC17 Series Mobile Computer .................................................................................. 1-12

Non-Touch and Touch Screens ..................................................................................................... 1-13

Data Capture ................................................................................................................................. 1-13

Scanning Considerations ......................................................................................................... 1-13

Scanning Bar Codes ................................................................................................................ 1-13

Scanning Tips .................................................................................................................... 1-14

LED Indications ........................................................................................................................ 1-14

vi MC17/MC17A/MC17T/MC17U Product Reference Guide

Resetting the MC17 Series Mobile Computer ............................................................................... 1-15

Performing a Warm Boot ......................................................................................................... 1-15

Performing a Cold Boot ............................................................................................................ 1-15

Replacing the Bezel ....................................................................................................................... 1-16

Chapter 2: Staging and Provisioning

Introduction .................................................................................................................................... 2-1

Staging ........................................................................................................................................... 2-1

Bar Code Staging ..................................................................................................................... 2-2

On-Demand Staging ................................................................................................................ 2-4

ActiveSync Connection Mode ............................................................................................ 2-4

Already existing IP Connection Mode ................................................................................ 2-4

Well-known WLAN Connection Mode ................................................................................ 2-4

RD Client Main Menu ............................................................................................................... 2-6

Client Info ........................................................................................................................... 2-6

Log Menu ........................................................................................................................... 2-7

View Log ............................................................................................................................ 2-7

View Job Log ..................................................................................................................... 2-8

Set Log Level ..................................................................................................................... 2-8

Set Job Log Level .............................................................................................................. 2-9

Package List ...................................................................................................................... 2-9

Provisioning ................................................................................................................................... 2-11

MSP Agent ............................................................................................................................... 2-11

MSP Agent Main Menu ............................................................................................................ 2-11

Monitor Processing ............................................................................................................ 2-12

Force Check-In .................................................................................................................. 2-12

Package List ...................................................................................................................... 2-12

Client Info ........................................................................................................................... 2-13

Log Menu ........................................................................................................................... 2-13

View Log ............................................................................................................................ 2-14

View Job Log ..................................................................................................................... 2-14

Set Log Level ..................................................................................................................... 2-15

Set Job Log Level .............................................................................................................. 2-15

Hide UI ............................................................................................................................... 2-16

Chapter 3: Wireless Applications

Introduction .................................................................................................................................... 3-1

802.11d Overview .......................................................................................................................... 3-1

Configuring My Country for Use with WLAN on an MC17 Series .................................................. 3-1

Enabled 802.11d Network ........................................................................................................ 3-2

Disabled 802.11d Network ....................................................................................................... 3-2

Create WCS Options Registry File .................................................................................... 3-2

Update MC17 via 802.11d Enabled Staging Network ........................................................ 3-2

Connect to the Non-802.11d Network ................................................................................ 3-3

Wireless Application on the MC17T/MC17U ................................................................................. 3-3

Signal Strength Icon ...................................................................................................................... 3-4

Turning Off the Radio .................................................................................................................... 3-5

Table of Contents vii

Chapter 4: ActiveSync

ActiveSync ..................................................................................................................................... 4-1

Installing ActiveSync ...................................................................................................................... 4-1

Mobile Computer Setup ................................................................................................................. 4-2

Setting Up an ActiveSync Connection on the Host Computer ....................................................... 4-2

Setting up a Partnership .......................................................................................................... 4-3

Chapter 5: Using the Windows CE Desktop

Introduction .................................................................................................................................... 5-1

ActiveSync ..................................................................................................................................... 5-1

Remote Control Software ............................................................................................................... 5-1

Connection to Host Computer ........................................................................................................ 5-1

Development Cable Removal .................................................................................................. 5-5

App Launcher Window ................................................................................................................... 5-6

Windows CE 5.0 Desktop .............................................................................................................. 5-7

Status Icons ............................................................................................................................. 5-7

Battery Unknown Icon .............................................................................................................. 5-8

Start Button .............................................................................................................................. 5-9

Programs Menu ....................................................................................................................... 5-9

Desktop Display Button ............................................................................................................ 5-10

Entering Information Using the Keyboard Input Panel ............................................................. 5-10

Task Bar and Start Menu Properties ........................................................................................ 5-10

Properties ........................................................................................................................... 5-10

Advanced Tab .................................................................................................................... 5-11

Screen Calibration ......................................................................................................................... 5-11

Waking the MC17 Series ............................................................................................................... 5-12

Chapter 6: Special Considerations

Introduction .................................................................................................................................... 6-1

Fonts .............................................................................................................................................. 6-1

Asian Font Installation .............................................................................................................. 6-2

Software Development Considerations .......................................................................................... 6-2

Tips for Improving Battery Charge Time ........................................................................................ 6-2

Cradle-Backlight Feature ......................................................................................................... 6-3

Tips for Improving Battery Life ....................................................................................................... 6-3

Changing the Power Settings .................................................................................................. 6-4

Changing the Display Backlight Settings ................................................................................. 6-4

MC17U Non-touch Support ...................................................................................................... 6-5

Chapter 7: Pocket Browser

Introduction .................................................................................................................................... 7-1

Sample Application ........................................................................................................................ 7-1

Chapter 8: Cradle Installation

Introduction .................................................................................................................................... 8-1

Installation of the Charging Cradle ................................................................................................. 8-1

Removing the Front Cover ....................................................................................................... 8-1

viii MC17/MC17A/MC17T/MC17U Product Reference Guide

Mounting the Cradle ................................................................................................................. 8-2

Wiring ............................................................................................................................................. 8-4

Assembly ....................................................................................................................................... 8-5

Cradle Location Bar Code ........................................................................................................ 8-6

System Cabling .............................................................................................................................. 8-7

Mounting the Power Supply Housing ............................................................................................. 8-9

Chapter 9: Application Deployment

Software Installation on Development PC ..................................................................................... 9-1

Device Configuration Package ................................................................................................. 9-1

Platform SDK ........................................................................................................................... 9-2

Enterprise Mobility Developer Kits ........................................................................................... 9-2

Installing Other Development Software ................................................................................... 9-2

Deployment .................................................................................................................................... 9-3

ActiveSync ............................................................................................................................... 9-3

IPL ............................................................................................................................................ 9-4

Creating Hex Images ..................................................................................................................... 9-5

Starting Terminal Configuration Manager ................................................................................ 9-5

Defining Script Properties ........................................................................................................ 9-7

Creating the Script for the Hex Image ...................................................................................... 9-8

Opening a New or Existing Script ...................................................................................... 9-8

Updating TCM 1.X Scripts ................................................................................................. 9-8

Copying Components to the Script .................................................................................... 9-8

Saving the Script ................................................................................................................ 9-9

Building the Image ................................................................................................................... 9-9

Sending the Hex Image Using IPL ................................................................................................. 9-10

TCM Error Messages ............................................................................................................... 9-14

IPL Error Detection .................................................................................................................. 9-16

Creating a Splash Screen ........................................................................................................ 9-18

Splash Screen Format ............................................................................................................. 9-18

OS Update ..................................................................................................................................... 9-19

MC17 and MC17A ................................................................................................................... 9-19

MC17T/MC17U ........................................................................................................................ 9-21

Flash Storage ................................................................................................................................ 9-23

FFS Partitions .......................................................................................................................... 9-23

Working with FFS Partitions ..................................................................................................... 9-23

RegMerge.dll ...................................................................................................................... 9-23

CopyFiles ........................................................................................................................... 9-24

Non-FFS Partitions .................................................................................................................. 9-24

Downloading Partitions to the Mobile Computer ...................................................................... 9-25

Chapter 10: Maintenance and Troubleshooting

Introduction .................................................................................................................................... 10-1

Maintaining the Mobile Computer .................................................................................................. 10-1

Battery Safety Guidelines .............................................................................................................. 10-1

Battery Management ..................................................................................................................... 10-2

Clearing the Battery ................................................................................................................. 10-2

Long Term Storage ........................................................................................................................ 10-3

Cleaning ......................................................................................................................................... 10-4

Table of Contents ix

Materials Required ................................................................................................................... 10-4

Cleaning the MC17 Series ....................................................................................................... 10-4

Housing .............................................................................................................................. 10-4

Display ............................................................................................................................... 10-4

Scanner Exit Window ......................................................................................................... 10-4

Connector ........................................................................................................................... 10-4

Cleaning Cradle Connectors .................................................................................................... 10-5

Cleaning Frequency ................................................................................................................. 10-5

Troubleshooting ............................................................................................................................. 10-6

Mobile Computer ...................................................................................................................... 10-6

Charging Cradle ....................................................................................................................... 10-9

Appendix A: Technical Specifications

Technical Specifications ................................................................................................................ A-1

Charging Cradle ....................................................................................................................... A-3

Cable Specifications ...................................................................................................................... A-6

Power Supply Cable, Y-type .................................................................................................... A-6

Cradle Interconnection Cable .................................................................................................. A-6

Appendix B: AirBEAM Smart Client

Introduction .................................................................................................................................... B-1

AirBEAM Package Builder ............................................................................................................. B-1

AirBEAM Smart Client .................................................................................................................... B-2

AirBEAM License ..................................................................................................................... B-2

Configuring the AirBEAM Smart Client .................................................................................... B-2

Packages(1) Tab ................................................................................................................ B-2

Packages(2) Tab ................................................................................................................ B-3

Server Tab ......................................................................................................................... B-4

Misc(1) Tab ........................................................................................................................ B-4

Misc(2) Tab ........................................................................................................................ B-5

Misc(3) Tab ........................................................................................................................ B-6

Misc(4) Tab ........................................................................................................................ B-7

Synchronizing with the Server ............................................................................................ B-8

Manual Synchronization ..................................................................................................... B-9

Automatic Synchronization ................................................................................................. B-9

AirBEAM Staging ..................................................................................................................... B-9

Appendix C: App Launcher Configuration

Configuration .................................................................................................................................. C-1

Glossary

Index

x MC17/MC17A/MC17T/MC17U Product Reference Guide

ABOUT THIS GUIDE

Introduction

This guide provides information about setting up and configuring MC17 mobile computers and accessories.

NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.

Documentation Set

The documentation set for the MC17 is divided into guides that provide information for specific user needs.

•

MC17/MC17A/MC17T/MC17U Mobile Computer Quick Reference Guide - describes how to set up the

MC17,MC17A and MC17T mobile computers.

•

MC17/MC17A/MC17T/MC17U Mobile Computer Product Reference Guide - describes how to set up,

operate and program the MC17 series mobile computer and the accessories.

•

Microsoft Applications for Windows Mobile and WinCE 5.0 User Guide - describes how to use Microsoft

developed applications.

•

Application Guide for Zebra Devices - describes how to use Zebra developed applications.

•

EMDK Help File - provides API information for writing applications.

xii MC17/MC17A/MC17T/MC17U Product Reference Guide

User Types

SMDK for eVC4

Box or Support Central Web Site

Microsoft Appication Guide

Zebra Application Guide

Product Reference Guide

End-User

Quick Reference Guide

Integrator

Application

Developer

SMDK Help File

Configurations

This guide covers the following configurations:

Configuration Radio Display Memory

MC17-00 WLAN: 802.11b/g 2.8”

MC17A-00 WLAN:

MC17T-00 WLAN:

MC17U-00 WLAN:

802.11a/b/g

QVGA Color

2.8” QVGA Color

2.8” QVGA Color touch screen

64 MB RAM/ 64 MB Flash

64 MB RAM/ 64 MB Flash + 1 GB Flash storage

Data

Capture

Laser scanner

Operating

System

Windows CE 5.0 Professional

Keypad

6-key

About This Guide xiii

ZEBRA

Software Versions

This guide covers various software configurations and references are made to operating system or software versions.

OEM Software

To determine the OEM software version on the MC17:

1. Connect the mobile computer to a host computer using the Development Cable.

2. Connect to the mobile computer using remote control software. See Remote Control Software on page 5-1

for more information.

3. Click Start > Settings > Control Panel > System Info icon.

To determine the OEM software version on the MC17 series with OEM Version 01.30.06 or greater:

Fusion Software

To determine the Fusion software version on MC17 series with OEM version 01.30.06 or greater:

App Launcher, select 3 - Device Info.

xiv MC17/MC17A/MC17T/MC17U Product Reference Guide

ZEBRA

Chapter Descriptions

Topics covered in this guide are as follows:

•

Chapter 1, Getting Started, lists the accessories for the mobile computer and explains how to install and

charge the batteries and start the mobile computer for the first time.

•

Chapter 2, Staging and Provisioning, provides information for staging and provisioning the mobile

computer using Mobility Software Platform (MSP).

•

Chapter 3, Wireless Applications, provides instructions for configuring the wireless adapter.

•

Chapter 4, ActiveSync, provides instructions on installing ActiveSync and setting up a partnership

between the mobile computer and a host computer.

•

Chapter 5, Using the Windows CE Desktop, Provides instructions for accessing the OS desktop of the

mobile computer.

•

Chapter 6, Special Considerations, provides information to consider when using and developing

applications for the mobile computer.

•

Chapter 7, Pocket Browser, provides instructions for installing ActiveSync and setting up a partnership

between the mobile computer and a host computer.

•

Chapter 8, Cradle Installation, provides the installation instructions for the Charging cradle and other

accessories.

•

Chapter 9, Application Deployment, provides instructions for installing the Device Configuration Package

(DCP) for MC17x0 and the EMDK for C on the host computer and downloading software and files to the mobile computer.

•

Chapter 10, Maintenance and Troubleshooting, includes instructions on cleaning and storing the mobile

computer, and provides troubleshooting solutions for potential problems during mobile computer operation.

•

Appendix A, Technical Specifications, includes a table listing the technical specifications for the mobile

computer and accessories.

•

Appendix B, AirBEAM Smart Client, provides information for staging and provisioning the mobile

computer using the AirBEAM Smart Client.

•

Appendix C, App Launcher Configuration, provides information for configuring the App Launcher

application.

Notational Conventions

The following conventions are used in this document:

•

“Mobile computer” refers to the Zebra MC17 series of mobile computers.

•

Italics are used to highlight the following:

• Chapters and sections in this guide

• Related documents

•

Bold text is used to highlight the following:

• Dialog box, window and screen names

• Drop-down list and list box names

• Check box and radio button names

• Icons on a screen

• Key names on a keypad

• Button names on a screen.

•

Bullets (•) indicate:

• Action items

• Lists of alternatives

• Lists of required steps that are not necessarily sequential.

About This Guide xv

Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.

NOTE This symbol indicates something of special interest or importance to the reader. Failure to read the note

will not result in physical harm to the reader, equipment or data.

CAUTION This symbol indicates that if this information is ignored, the possibility of data or material damage

may occur.

WARNING! This symbol indicates that if this information is ignored the possibility that serious personal

injury may occur.

Service Information

If you have a problem with your equipment, contact Zebra Global Customer Support for your region. Contact information is available at: http://www.zebra.com/support

When contacting Zebra Global Customer Support, please have the following information available:

•

Serial number of the unit

•

Model number or product name

•

Software type and version number.

Zebra responds to calls by E-mail or telephone within the time limits set forth in support agreements.

If your problem cannot be solved by Zebra Global Customer Support, you may need to return your equipment for servicing and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.

If you purchased your Zebra business product from a Zebra business partner, contact that business partner for support.

CHAPTER 1 GETTING STARTED

Introduction

This chapter describes the features of the MC17 series mobile computer and explains how to install and charge the battery, how to capture data using the integrated laser scanner and how to reset the mobile computer.

Unpacking

Carefully remove all protective material from the mobile computer and save the shipping container for later storage and shipping.

Verify that box contains all the equipment listed below:

•

MC17 mobile computer

•

Lithium-ion battery (installed in handle)

•

Quick Reference Guide.

Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact the Zebra Global Customer Support immediately. See Service Information on page xvi for contact information.

1 - 2 MC17/MC17A/MC17T/MC17U Product Reference Guide

MC17

series

Keypad

LED

Display

Bezel

Features

Figure 1-1

Front View

Introduction 1 - 3

Battery Cover

Access Cover

Speaker

Battery Cover Torx Screw

Power Connector

Scan Exit Window

Front Bezel Torx Screw

Figure 1-2

Back View

1 - 4 MC17/MC17A/MC17T/MC17U Product Reference Guide

Accessories

Table 1-1

Locking Charging Cradle

Non-Locking Charging Cradle

Cradle Key

Cradle Key Pack

Power Supply

Power Supply Housing PSS-3PS04-00R

Daisy Chain Cable

Power Cable

Y-Power Cable

Cradle Location Labels

Accessories

Item Part Number Description

PSS-3CR01-00R Provides power and storage for the mobile computer.

PSS-3CR01-NLR Provides power and non-locking storage for the mobile

PSS-3KY01-00R Manually releases the mobile computer from the

PSS-3KY01-20R Manually releases the mobile computer from the

50-14000-241R Provides power to the Charging cradle.

25-66431-01R Interconnects two Charging cradles.

25-66420-01R Connects the power supply to up to six Charging cradle

25-67592-01R Connects the power supply to up to 12 Charging cradles

PSS-3LB02-00R PSS-3LB03-00R PSS-3LB04-00R

computer.

Charging cradle.

Charging cradle. (20-pack)

Encloses the power supply.

(using the daisy chain cable).

Contains “1” - “300” pre-printed bar code labels. Contains six each, “1” - “300” pre-printed bar code labels. Contains “1” - “1000” pre-printed bar code labels.

Development Cable 25-101374-01R

USB Cable 25-68596-01R

Cart Holder

Screen Protector Kit

MC17 and MC17A Bezel

MC17T and MC17U Bezel

PSS-3SH01-00R Provides a mounting solution for the mobile computer on

KT-114012-01R Package of 3 screen protectors.

KT-098273-01R Package of 50 replacement bezels for the MC17 and

KT-098274-00R Package of 50 replacement bezels for the MC17T and the

Connects the mobile computer to a host computer along with the USB cable.

Connects the mobile computer to a host computer along with the Development cable.

a shopping cart.

MC17A.

MC17U.

LED Indicators

LED

Scan Key Down Arrow KeyUp Arrow Key

Scroll Left Key Enter Key Scroll Right Key

The LED indicates status of the MC17 mobile computer. Table 1-2 describes the LED indications.

Introduction 1 - 5

Figure 1-3

Table 1-2

Keypad

The keypad contains programmable function keys and a Scan key. Note that keypad functions can be changed by an application so the mobile computer’s keypad may not function exactly as described. See Table 1-3 on

page 1-6. Refer to the EMDK Help file for detailed information for programming the function keys.

MC17 Mobile Computer LED

LED Indications

LED State Indication

Solid red

Solid green Bar code decoded successfully.

Scanner is enabled.

Figure 1-4

Keypad

1 - 6 MC17/MC17A/MC17T/MC17U Product Reference Guide

Ta pe

Screw Under Tape

Table 1-3

Scroll Left Key Moves the cursor focus to the left.

Enter Key Executes a selected item or function.

Scroll Right Key Moves the cursor focus to the right.

Up Arrow Key Moves the cursor focus up.

Scan Key Enables the laser scanner when a scanning application is active.

Down Arrow Key Moves the cursor focus down.

Keypad Descriptions

Key Description

Getting Started

In order to start using the mobile computer for the first time:

•

Install the battery

•

Charge the battery.

Connecting the Battery

In order to start using the mobile computer you must install the battery and then charge it.

1. Remove tape securing battery cover to handle.

2. Remove screw from screw hole (under tape).

3. Slide the battery cover toward the bottom of the handle and then lift.

Figure 1-5

Remove Battery Cover

Introduction 1 - 7

Wire Latch

Screw Boss

4. Ensure that the black rubber pad in the battery compartment is lying flat along the bottom of the

compartment, with its smoother side facing up, and the rubber “fingers” straddling the screw boss.

5. Ensure the wire latch is in the up position.

6. Place the battery, rounded side down, in the compartment. Using a non-metallic tool (if necessary), guide

the battery cable connector into the female battery connector on the mobile computer.

Figure 1-6

Insert Battery

The connector is keyed so it only fits one way.

7. Press the connector down to ensure a positive connection.

8. Place wire latch down until just below top of the screw boss.

Figure 1-7

9. Place the battery cover onto the handle and slide it as shown.

Close Wire Latch

1 - 8 MC17/MC17A/MC17T/MC17U Product Reference Guide

Battery Door

Properly Aligned

Figure 1-8

10. Inspect the position of the battery cover with the main housing. If the door is misaligned, remove battery

Replace Battery Cover

and black rubber pad and re-install.

Figure 1-9

11. Secure the battery cover with the Torx screw using a T8 Torx drive.

Inspect Battery Door Alignment

Figure 1-10

12. After installing a new battery, wait approximately one minute before inserting the mobile computer into a

cradle.

Secure Battery Cover with Screw

Introduction 1 - 9

Red Charging LED Location

NOTE When installing a new battery or performing an OS Update, wait approximately one minute before inserting the

MC17 into a cradle.

13. Run the battery service procedure. See Clearing the Battery on page 10-2 for information.

Charging the Battery

CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page

NOTE Charge time is based upon the following; WLAN radio is set to maximum power mode, WLAN is

associated with an Access Point and display backlight set to 25% brightness.

10-1.

Before using the mobile computer for the first time, charge the battery. The battery fully charges in approximately five hours.

To charge the battery:

1. Ensure the Charging cradle is connected to the appropriate power source. See Chapter 8, Cradle

Installation for more information.

2. Insert the mobile computer into a cradle.

Figure 1-11

3. The mobile computer starts to charge automatically. While charging, a red charging LED can be seen

Insert MC17 Series into Cradle

through the front panel of the cradle behind the mobile computer.

1 - 10 MC17/MC17A/MC17T/MC17U Product Reference Guide

Manual Release of MC17 Series from the Charging Cradle

The Charging cradle, p/n PSS-3CR01-00R, contains a locking mechanism that locks the mobile computer into the cradle. The mobile computer releases from the cradle via a software command to the cradle. If the mobile computer does not have the capability to un-lock the cradle, un-lock it manually using the optional dispenser (cradle) key, (p/n PSS-3KY01-00R).

1. Hold key with hook end pointing to the right.

Figure 1-12

2. Insert key straight into slot, only to point where bend stops on lip of slot.

Figure 1-13

3. Slide key to the right until the handle is centered in the slot.

Insert Key

Key

Figure 1-14

Slide Key to the Right

4. Rotate the key 90 degrees (1/4 turn) counterclockwise.

Introduction 1 - 11

Figure 1-15

5. Keeping the handle of the key all the way to the right in the slot, press the key into the slot. The end of the

key should press on a small spring loaded tab within the cradle and release the mobile computer. You

should feel the tab moving as you press down.

Figure 1-16

6. While holding the key down, lift the mobile computer out of the cradle.

Slide Key to the Rotate Key Counterclockwise

Press Key into Slot

Software Release of MC17 Series from the Charging Cradle

7, Pocket Browser for more information.

1 - 12 MC17/MC17A/MC17T/MC17U Product Reference Guide

Starting the MC17 Series Mobile Computer

The mobile computer starts automatically as soon as power is applied; either with a charged battery installed or when inserted into the cradle. If the mobile computer does not power on, perform a cold boot. See Performing

a Cold Boot on page 1-15.

When the mobile computer is powered on for the first time, it initializes its system. The splash screen (Figure

1-17) appears for a short period of time.

Figure 1-17

On the MC17 and the MC17A, the splash screen is followed by the App Launcher window.

On the MC17T and the MC17U, the splash screen is followed by the Calibration screen. Carefully press and briefly hold a pointing instrument on the center of each target that appears on the screen. Repeat as the target moves around the screen, then tap the screen to continue. After completing the screen calibration, the App Launcher window appears.

Splash Screen

NOTE App Launcher window may vary depending upon the MC17 series’s operating system version.

Figure 1-18

App Launcher Window

+ 130 hidden pages

Zebra MC17 MC17 Product Reference Guide English

Specifications and Main Features

Frequently Asked Questions

User Manual

Revision History

TABLE OF CONTENTS

ABOUT THIS GUIDE

Introduction

Documentation Set

Configurations

Software Versions

OEM Software

Fusion Software

Chapter Descriptions

Notational Conventions

Related Documents and Software

Service Information

Introduction

Unpacking

Features

Accessories

LED Indicators

Keypad

Getting Started

Connecting the Battery

Charging the Battery

Manual Release of MC17 Series from the Charging Cradle

Software Release of MC17 Series from the Charging Cradle

Starting the MC17 Series Mobile Computer