Zebra Ikon iKôn Rugged PDA Quick Start Guide (en)

Contents of the box:

The Ikôn

March 24, 2009 PN: 8000150.C

I
S

O

9
0

0
1

C

e
r

t
i
f
i

e
d

Q

�

u

a

li
t
y

M

a
n

a
g

e

m
e

n
t

S

y
s

t
e

Battery cover

m

Features: Front And Ports

Power button

LEDs

Display

Battery

This Guide

Microphone
(between keys)

Keyboard

Additional documentation
(dependent on order)

Power adaptor
and plugs

Telephone audio speaker

Features: Back

Camera lens and ash

Speaker

Handstrap bar

Scanner window

Features: QWERTY Keyboard

Scan keys

Headset port

Battery cover

Features: Battery Compartment

Battery cover latches

Battery cover

SIM Card holder

MicroSD Card holder

Serial number label

Important: Before removing the battery, power the
Ikôn off as described at the end of this guide.

Features: Numeric Keyboard

Scan keys

Turn the battery cover latches
towards the outside of the
unit to unlatch the battery
cover; turn them towards the
centre of the unit to latch the
battery cover.

Closed and latched

Open and unlatched

Always place the latches in
the unlatched position when
removing or replacing the
battery cover.

Getting Started

Unlatch and open the battery compartment.

1

Insert the SIM card, if necessary.

2

Insert the battery.

3

Volume button

Scan button

Headset port

Docking port

Docking latch

Scan button

Vertical Scroll button

DC Input port

[TALK] key

[BLUE] key

[END] key

[ORANGE] key

[TALK] key

[BLUE] key

[END] key

[ORANGE] key

Note: On Ikôn units without the phone feature, the [TALK] key is replaced by an [ALT]
key, and the [END] key is replaced by a [CTRL] key.

Close and latch the battery compartment.

4

Over

Charge the battery.

5

The power adaptor may be plugged directly into the
Ikôn.

Note: Use only the universal
AC power supply approved
by Psion Teklogix for use
with the Ikôn.

Turn the unit on.

6

Press the Power button for four seconds.

Power button

Connect the Ikôn to the host computer.

7

Connect using a Tether port to USB cable, or through a
Docking Station.

Before removing the battery, turn the Ikôn off as
described below.

Failure to do so may cause the unit to become unresponsive,
requiring it to be reset as described below.

To turn the Ikôn off, do one of the following:

Press and hold the Power button until the • Shutdown menu

appears.

Select • Shutdown from the menu.

™

Rugged PDA

Quick Start Guide

July 14, 2009 PN: 8000150.D

The Ikôn may also be charged in
a Docking Station.

Allow the Ikôn to charge for four hours.

5 - 40 °C

41 - 104 °F

Note: Full battery performance is only reached after

4h

therstfewcharge/dischargecycles.

Note: Use only the universal
AC power supply approved by
Psion Teklogix for use with the
Docking Station.

Install ActiveSync®.

8

Go to http://go.microsoft.com/fwlink/?LinkId=147001 and
follow the instructions to download and install
ActiveSync 4.5 or higher.
Note: ActiveSync is not needed when connecting to a
host computer that uses the Windows® Mobile Device
Center (such as Microsoft® Windows Vista®).

Congure ActiveSync.

9

Follow the onscreen instructions provided by
ActiveSync to establish a connection between the host
computer and the Ikôn in the Docking Station.

Resetting the unit:

Important: Resetting the unit may result in data loss.

To warm-reset the Ikôn:

Press the [BLUE] and [ENTER] keys simultaneously •

for six seconds.

Select • Shutdown from the Start menu.

Psion Teklogix and Ikôn are trademarks
of Psion Teklogix Inc. Other product
names mentioned in this document are
trademarks or registered trademarks
of other hardware, software, or service
providers and are used herein for

identicationpurposesonly.

*8000150*

8000150

Rev. D

ISO 9001 Certied
Quality Management System