User's Manual
CNPS8900 Series
Intel
AMD
Socket FM2/FM1/AM3+/AM3/AM2+/AM2 CPU&APUs
Socket 1366/1156/1155/775 CPUs
To ensure safe and easy installation, please read
the following precautions.
www.ZALMAN.com
Ver.121113
1. Precautions
1) Avoid inserting objects or hands into the fan while it is in operation to prevent
product damage and injuries.
2) Do not ingest the Thermal Grease, and avoid its contact with skin and eyes. If
contact is made with skin, wash off with water. If ingested or irritation persists,
seek medical attention.
3) To prevent possible injuries, gloves must be worn while handling this product.
4) Excessive force exerted on the fan may cause damage to the fan and/or
system.
5) Use and keep product away from reach of children.
6) Check the components list and condition of the product before installation. If
any problem is found, contact the retailer to obtain a replacement.
7) During transportation of the system, the cooler must be removed. Zalman is
not responsible for any damages that occur during the transport of a system.
8) Productdesignandspecicationsmayberevisedtoimprovequalityand
performance.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due to
1)
external causes, including but not limited to, improper use, problems
with electrical power, accident, neglect, alteration, repair, improper
installation, or improper testing.
2.
Specications
Spec.
Fan
Model
Material Pure Copper and Aluminum
Weight 400g
Dimensions
Bearing 2 Ball-Bearing Long Life Bearing
RPM 1,250~2,800 rpm ± 10% 1,000~1,500 rpm ± 10%
Noise Level 19.5 ~ 35dBA ± 10% 19 ~ 25dBA ± 10%
Input Voltage
3.
Installation Requirements
Space Requirements
The cooler’s installation requires an
unobstructed space of 120mm(width),
120mm(length), and 60mm(height), with the
CPU as a central reference point.
Please check if components such as ODDs
and PSU protrude into the required space.
CNPS8900 Extreme CNPS 8900 Quiet
120(L) x 120(W) x 60(H)mm
12V
60 mm
WWW.ZALMAN.COM
120 mm
120 mm
1
4.
Components
1) Common Components
Cooler
Bolts (Cooler) Bolts (Clip) Extension Fan Cable
Loading Block Double-sided Tape
2) Intel Components 3) AMD Components
2) Intel 구성품
(Socket 1366/1156/1155/775)
Intel Clip
(
Socket FM2/FM1/AM3+/AM3/AM2+/ AM2
Backplate
User’s ManualNutsSide Caps
Thermal Grease
(ZM-STG2M)
AMD Clip
)
WWW.ZALMAN.COM
2
5. Installation
Common
Connect the extension fan cable to the fan connector of cooler.
Cooler Fan connector
Extension Fan Cable
.
Intel Socket 1366/1156/1155/775 Installation
A
①
Install the Intel clip to the base of cooler using the bolts (Clip).
Please make sure to put the curved part of clip toward the base as shown
in the image.
Intel Clip
WWW.ZALMAN.COM
3
②
X
O
Install the side cap to the Backplate according to a socket type.
Socket
775
Socket
1156/1155
2
1
Caution
Please note the orientation of the Nuts and the Side Caps.
③ Socket 1366/1156/1155 Installation
Attach Double-sided Tape to the center of the Backplate and remove
the Double-sided Tape’s Cover.
※ Installation of Socket 1366/1156/1155 does not require the Loading
Block.
Double-sided Tape
Socket
1366
WWW.ZALMAN.COM
4
X
O
④ Socket 775 Installation
Remove the Sticker Cover from the Lower Tier of the Loading Block and
attach to the Backplate.
Loding Block
Attach Double-sided Tape to the Loading Block and remove the Double-sided
Tape Cover.
Double-sided Tape
Caution
Please note of the orientation of the Loading Block's Installation.
WWW.ZALMAN.COM
5
⑤
X
O
Align the Backplate’s holes with motherboard’s clip support holes, attach it
to the back side of the motherboard.
⑥
Spread the Thermal Grease on the CPU’s surface and put the Cooler
on the center of CPU and then fasten the Bolts (Cooler) to install the Cooler.
1366
Socket
1156/1155
Socket
775
Socket
Caution
In the case of Tower Enclosure, the direction of heatpipe to be
horizontally as shown in the image. The vertical installation can affect
the performance of heat dissipation.
⑦
Connect the cooler’s 4-pin connector to the motherboard’s CPU Fan
header.
Caution
Please make sure that PWM
Control Mode is activated
in the motherboard’s BIOS settings.
M/B
WWW.ZALMAN.COM
6
AMD Socket FM2/FM1/AM3+/AM3/AM2+/AM2 Installation
X
O
.
B
①
Install the AMD Clip to the base of cooler using the bolts (Clip).
Please make sure to put the curved part of clip toward the base as shown
in the image.
AMD Clip
②
Install the side cap to the Backplate.
2
1
Caution
Please note of the orientation of Nuts and side Caps.
WWW.ZALMAN.COM
7
③
O
X
Remove the Sticker Cover from the Lower Tier of the Loading Block
and attach to the Backplate.
Loading Block
Attach Double-sided Tape to the Loading Block and remove the Double-sided
Tape Cover
Double-sided Tape
Caution
Please note of the orientation of the Loading Block's Installation.
④
TakeawaythexedClipsupportfromthemotherboard.
M/B
WWW.ZALMAN.COM
M/B
8
⑤
Align the Backplate’s holes with motherboard’s clip support holes, attach it
to the back side of the motherboard.
M/B
⑥
Spread the Thermal Grease on the CPU’s surface and put the Cooler
on the center of CPU and then fasten the Bolts (Cooler) to install the Cooler.
⑦
Connect the cooler’s 4-pin connector to the motherboard’s CPU Fan
header.
Caution
Please make sure that PWM
M/B
Control Mode is activated
in the motherboard’s BIOS settings.
WWW.ZALMAN.COM
9
McGrp.Ru
Сайт техники и электроники
Наш сайт McGrp.Ru при этом не является просто хранилищем
инструкций по эксплуатации, это живое сообщество людей. Они общаются
на форуме, задают вопросы о способах и особенностях использования техники.
На все вопросы очень быстро находятся ответы от таких же посетителей сайта,
экспертов или администраторов. Вопрос можно задать как на форуме, так и
в специальной форме на странице, где описывается интересующая вас техника.
Loading...