Heatsink Filter Kit Option
y
For F7 Configured Drive
Introduction
This Installation Guide applies to the Heatsink Filter Kit Option for the F7 Configured Drive line. The filter kit is mounted to
the back of the F7C enclosure, providing additional protection to the exposed drive heatsink and fan assemblies. The kit can
be field-installed to an F7 Configured Drive that is already mounted and in use. It has been designed for extremely dirty or
dusty environments in which cooling fans and heatsink fins could easily become clogged. The kit contains a duct and a pair
of filters, which can be removed and cleaned, increasing fan life and cooling efficiency. This guide is divided into three
sections detailing the included parts, kit installation, and filter replacement.
WARNING
HAZARDOUS VOLTAGE CAN CAUSE SEVERE INJURY OR DE ATH. LOCK ALL POWER
SOURCES TO THE DRIVE IN THE “OFF” POSITION.
CAUTION
• To prevent physical damage to the Drive, Read these instructions thoroughly before installing.
After installing the heatsink filter kit, ensure all screws are tightened.
•
Heatsink Duct (2) - Filter
Housing
Subassembl
Figure 1 – Filter Kit, Exploded View
Yaskawa Electric America, Inc – www.drives.com
IG.F7C.01 Page 1 of 7
Date: 3/5/04
p
g
Heatsink Filter Kit Part Numbers
Heatsink Filter Kit
Part No.
UFL00003-1
UFL00003-2
UFL00003-3
Applicable Drive Models
F7CT
A003 3/4
A004 1
A006 2
A009 3
A015 5
B001 3/4
B002 1
B003 2
B004 3
B007 5
B011 7.5
A022 7.5
A028 10
B014 10
B021 15
A042 15
A054 20
B027 20
B034 25
HP
Heatsink Filter Kit Option
For F7 Configured Drive
Parts Included
Heatsink Duct
Filter Housing Subassembly
Small Screws (#8-32 Phillips pan head)
Large Screws (#10-32 Phillips pan head)
Heatsink Duct
Filter Housing Subassembly
Small Screws (#8-32 Phillips pan head)
Large Screws (#10-32 Phillips pan head)
Heatsink Duct
Filter Housing Subassembly
Small Screws (#8-32 Phillips pan head)
Large Screws (#10-32 Phillips pan head)
Qty
1
2
2
4
1
2
2
4
1
2
2
4
Filter material
Figure 2 – Filter Housing Subassembly, Exploded View
(2) – Mounting Screws,
ca
tivated with o-rin
Filter housing
Yaskawa Electric America, Inc – www.drives.com
IG.F7C.01 Page 2 of 7
Date: 3/5/04
Heatsink Filter Kit Option
g
g
Heatsink Filter Kit Installation
(1) Turn OFF the power supply to the Drive by completely removing power to the enclosure. Wait 5 minutes for
capacitor discharge.
(2) Unpack and verify the contents of the heatsink filter kit.
Refer to Figures 3a and 3b – Removal of mounting screws
(3) Open enclosure using (2) quarter turn latches on door of enclosure
(4) Locate the screws that attach the enclosure to the back panel. Three screws exist at the top of the enclosure
(Figure 3a), and three at the bottom of the enclosure (Figure 3b). Remove only the center screw from both
the top and bottom of the enclosure, as shown below. These screws will no longer be used once the heatsink
filter kit in installed.
For F7 Configured Drive
Remove screw
from upper rear
flan
e
Figure 3a – Upper screw Removal (Step 4)
Remove screw
from lower rear
flan
e
Figure 3b – Lower screw Removal (Step 4)
Yaskawa Electric America, Inc – www.drives.com
IG.F7C.01 Page 3 of 7
Date: 3/5/04
Loading...