Yamaha TRX-1R, TRX-1T User Manual

GB

TRX-1

(TRX-1T + TRX-1R)

Wireless Unit

Système sans fil

(TRX-1R) (TRX-1T)

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

CAUTION: READ THIS BEFORE OPERATING TRX-1

• To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.

• Install TRX-1 in a well ventilated, cool, dry, clean place - away
from direct sunlight, heat sources, vibration, dust, moisture, and/
or cold. Allow ventilation space of at least 10 cm on the top, 10
cm on the left and right, and 10 cm on the back of these units.

• Locate TRX-1 away from other electrical appliances, motors, or
transformers to avoid humming sounds.

• Do not expose TRX-1 to sudden temperature changes from cold
to hot, and do not locate TRX-1 in a environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside TRX-1, which may cause an electrical shock, fire, damage
to TRX-1, and/or personal injury.

• Avoid installing TRX-1 where foreign object may fall onto
TRX-1 and/or TRX-1 may be exposed to liquid dripping or
splashing. On the top of TRX-1, do NOT place:

- Other components, as they may cause damage and/or

discoloration on the surface of TRX-1.

- Burning objects (i.e. candles), as they may cause fire, damage

to TRX-1, and/or personal injury.

- Containers with liquid in them, as they may fall and liquid may

electrical shock to the user and/or damage to TRX-1.

• Do not cover the rear panel of TRX-1 with a newspaper,
tablecloth, curtain, etc., in order not to obstruct heat radiation. If
the temperature inside TRX-1 rises, it may cause fire, damage to
TRX-1, and/or personal injury.

• Do not plug in TRX-1 to a wall outlet until all connections are
complete.

• Do not operate TRX-1 upside-down. It may overheat, possibly
causing damage.

• Do not use force on switches and/or cables.

• When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.

• Do not clean TRX-1 with chemical solvents; this might damage
the finish. Use a clean, dry cloth.

• Only voltage specified on TRX-1 must be used. Using TRX-1
with a higher voltage than specified is dangerous and may cause
fire, damage to TRX-1, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of
TRX-1 with a voltage other than specified.

• To prevent damage by lightning, disconnect the AC power cable
(or AC adaptor) from the wall outlet during an electrical storm.

• Do not attempt to modify or fix TRX-1. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.

• When not planning to use TRX-1 for long periods of time (i.e.
vacation), disconnect the AC power plug (or AC adaptor) from
the wall outlet.

• Use only the included AC adaptor with the TRX-1T. Using
another adaptor may cause a malfunction or fire.

• Do not use the AC adaptor with any device other than the TRX­1T.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THESE UNITS TO RAIN OR MOISTURE.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT

The wires in this mains lead are coloures in accordance with the
following code:

GREEN-and-YELLOW:Earth
BLUE:Neutral
BROWN:Live

As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows: The wire which is
coloured GREEN-and-YELLOW must be connected to the
terminal in the plug which is marked by the letter E or by the
safety earth symbol or coloured GREEN or GREEN-and ­YELLOW. The wire which is coloured BLUE must be
connected to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED.

For U.K. customers

If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described above.

Note:

The plug severed from the mains lead must be destroyed,

as a plug with bared flexible cord is hazardous if engaged in a live
socket outlet.

For U.K. and European customers

We, the manufacturer YAMAHA hereby declare that the TRX-1
is in compliance with the essential requirements and other
relevant provisions of Directive 1999 / 5 / EC.

The TRX-1 uses wireless signals in the 864 MHz
band. Using it in close proximity to other devices
that utilize the same band range may cause
pauses or interruptions in sound output, or
cause the unit to lose connections with the
receivers. The TRX-1 may also cause certain
medical equipment to function improperly.
Take care to ensure that no interference will
occur before use.

This unit is not disconnected from the AC power source as long
as it is connected to the wall outlet, even if this unit itself is
turned off. This state is called the standby mode. In this state,
this unit is designed to consume a very small quantity of power.

The TRX-1 is a wireless system for surround sound speakers, which allows you to enjoy your AV experience in a room
free of the clutter of speaker cables. It consists of a wireless transmitter unit (TRX-1T) and a wireless receiver unit (TRX­1R).

This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc., In case of differences between the manual and the product, the product has priority.

CONTENTS

SUPPLIED ACCESSORIES...................................1

CONTROLS AND FUNCTIONS.............................2

Wireless transmitter unit (TRX-1T)......................2

Wireless receiver unit (TRX-1R)..........................2

SUPPLIED ACCESSORIES

Please check that you received all of the following parts.

• AC adaptor
(Europe model: 430407890100)
(U.K. model: 430407890110) • Stand

• Cable plugs (A)
(Blue x 1, Gray x 1)

• Cable plugs (B)

CONNECTIONS.....................................................3

Placing the units..................................................3

Connecting the wireless transmitter unit .............3

Connecting the wireless receiver unit .................4

OPERATIONS........................................................5

SPECIFICATIONS .................................................5

(Blue x 1, Gray x 1)

English

1

CONTROLS AND FUNCTIONS

Wireless transmitter unit (TRX-1T)

1

2

1 Antenna

Adjust the antenna direction for best signal
transmission.

2 POWER indicator

Lights red when you connect the AC adaptor to the DC
IN jack on this unit and to an AC outlet. If the unit does
not receive a signal from the amplifier within 5 minutes
after connection to the AC outlet, it places itself in
standby mode and the power indicator goes out. The
unit turns on again when it receives a signal from the
amplifier.

Wireless receiver unit (TRX-1R)

The following figure depicts the unit with the cover removed.

5
4

3

3 Speaker terminal cable

Connect to the surround speaker jack on your amplifier.

4 CHANNEL SELECTOR switch

Set to the number selected on the channel selector of
the wireless receiver unit (see page 5).

5 DC IN jack

Connect to the included AC adaptor.

5

4

1
2

1 AC power cable

Connect the plug to an AC outlet.

2 Surround speaker terminal

Connect the speaker cables to the surround sound
speakers.

3 CHANNEL SELECTOR switch

Set to the number selected on the channel selector of
the wireless transmitter unit (see page 5).

2

3

4 Antenna

Adjust the antenna direction for best signal reception.

5 POWER indicator

Lights red when you connect the AC power cable to an
AC outlet. Lights green when the unit receiving a signal
from wireless transmitter unit. When the signal from
the wireless transmitter unit is cut, the unit places itself
in standby mode, and the power indicator lights red.

CONNECTIONS

Before connecting, make sure that the power of all components is off. Be sure to connect the wireless
transmitter unit to a component equipped with a volume control.

Placing the units

• Place both the wireless transmitter unit and wireless
receiver unit at least 30 cm off the ground.

• Make sure that you place the wireless transmitter unit and
wireless receiver unit 2–15 meters apart.

• Avoid placing the wireless units too close to your
amplifier, AC adaptor, TV or other electrical equipment
as it may cause electrical interference.

TRX-1T

To AC outlet

→

AC adaptor

To your amplifier

→

2–15 m

TRX-1R

Connecting the wireless
transmitter unit

1 Connect and carefully match the wireless

transmitter unit inputs to the corresponding
surround speaker jacks on your amplifier.

• Connect the blue/black speaker terminal cables to the
surround L speaker jack on your amplifier, and the grey/
black speaker terminal cable to the surround R speaker jack.

• Connect the black speaker cables to the minus terminals of
the speaker jacks, and the blue (or grey) speaker cables to the
positive terminals.

2 Connect the AC adaptor to the wireless

transmitter unit and an AC outlet.

■ Connecting to the YAMAHA
CinemaStation

When connecting to the YAMAHA DVR-S150/S120/S200
or the AVC-S20, connect the supplied cable plugs (B) to
the speaker terminal cables as shown below.

Press and hold the release button, insert the speaker
terminal cable core into the cable plug (B), then release the
button.
Match the speaker terminal cable polarity (+/–) with the
polarity marks (+/–) of the cable plug.

←

To AC outlet

To your speakers

→

Polarity mark –

(Black)

Polarity mark +

(Blue or Gray)

Release button

Attach the other cable plug (B) in the same way.

English

3

CONNECTIONS

Connecting the wireless receiver
unit

■ Attaching the cable plugs (A) to
the speaker cables

1 Pull both sides of the cover of the cable plug (A)

firmly away from the top of the plug, then partially
remove the top part of the cover.

2 Peel away about 15 mm of covering from the tip of

a commercially available speaker cable and twist
the cable core firmly in a clockwise direction.
Twisting loosely may cause a short circuit.

15 mm

■ Connecting the wireless receiver
unit

1 Remove the cover from the wireless receiver unit

as shown below, to access the connection
terminal. Connect your rear speaker terminals
with the corresponding color terminals on the
wireless receiver unit. Reattach the cover.

←

To

AC outlet

Surround R

speaker

(Gray)

(Blue)

Surround L

speaker

Good No Good

3 Match the speaker cable polarity (+/–) with the

polarity mark (+/–) of the cable plug, then insert
each cable core into the cable plug (A). Be sure
that it is firmly in contact with the metal part of the
speaker cable.

4 Replace the cover.

Attach the other cable plug (A) in the same way.

2 Insert the stand into the brackets as shown below.

3 Connect the AC power cable of the wireless

receiver unit to an AC outlet.

4

OPERATIONS

1 Check and adjust the channel selector switch on

the wireless transmitter unit and the wireless
receiver unit, so that both units are using the same
channel.

2 On your amplifier, play an audio source and

activate the surround sound mode option. Adjust
the amplifier volume to reproduce surround sound
from the surround speakers.

SPECIFICATIONS

TRX-1 (TRX-1T + TRX-1R)

Transmission Frequency.................................... 864 MHz

Selectable Channel.......................................................... 4

Transmission Distance.............................................. 15 m

TRX-1T

Transmission Power.............................................. 10 mW

Audio Input.......................................................17 V max.

Power Supply......................................................DC 14 V

Power Consumption...............................................1.82 W

Dimensions ........................................ 131 x 34 x 130 mm

Weight..................................................................... 0.3 kg

3 To improve reception, set the antennas on both

the wireless transmitter unit and the wireless
receiver unit to a vertical position. Check the
antennas are safely positioned without
obstruction.

Note

If the sound appears distorted, please select another
channel for both the wireless receiver unit and wireless
transmitter unit. The distortion could be the result of
interference caused by other equipment using same
frequency channel in your house or neighbourhood.

TRX-1R

Output Power (10% THD, 6 ohm)..................... 30 W x 2

Frequency Response.....................50 Hz – 20 kHz, ±3 dB

THD (1 kHz, 1W) ......................................... 0.5% or less

Power Supply ...............................220 – 240 V, 50/60 Hz

Power Consumption ................................................. 20 W

Standby Power Consumption..........................1 W or less

Dimensions.........................................207 x 55 x 186 mm

Weight ........................................................................1 kg

Specifications are subject to change without notice.

English

5