Yamaha RX-V396RDS User Manual

RX-V396RDS

Natural Sound AV Receiver Ampli-tuner audio-vidéo

G B

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

2. Install this unit in a cool, dry, clean place — away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the unit, contact your dealer.

4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power cord and then the wires connected to other component. Never pull the wires themselves.

5. The openings on the cover assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the unit will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in a well-ventilated area to prevent fire and damage. Be sure to allow a space of at least 20 cm behind, 20 cm on both sides and 30 cm above the top panel of the unit to prevent fire and damage.

6. The voltage used must be the same as that specified on this unit. Using this unit with a higher voltage than specified is dangerous and may result in fire or other accidents. YAMAHA will not be held responsible for any damage resulting from the use of this unit with a voltage other than that specified.

7. Digital signals generated by this unit may interfere with other component such as tuners, receivers and TVs. Move this unit farther away from such component if interference is observed.

8. Always set VOLUME to the “m” position before starting the audio source play. Increase the volume gradually to an appropriate level after playback has been started.

9. Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty.

11. When not planning to use this unit for a long period of time (e.g., a vacation), disconnect the AC power cord from the wall outlet.

12. To prevent lightning damage, disconnect the AC power cord and disconnect the antenna cable when there is an electrical storm.

13. Grounding or polarization — Precautions should be taken so that the grounding or polarization of the unit is not defeated.

14. AC outlet — Do not connect audio component to the AC outlet on the rear panel if that component requires more power than the outlet is rated to provide.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

CAUTION

INTRODUCTION

FEATURES

5-Channel Power Amplification

◆ Minimum RMS Output

(0.06% THD, 20 Hz – 20 kHz) Main: 60 W + 60 W (8 Ω) Center: 60 W (8 Ω) Rear: 60 W + 60 W (8 Ω)

Multi-mode Digital Sound Field Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Digital Decoder

◆ Dolby Pro Logic Decoder

◆ CINEMA DSP: Theater-like Sound Experience by

the Combination of YAMAHA DSP Technology and Dolby Digital or Dolby Pro Logic

◆ Automatic Input Balance Control for Dolby Pro

Logic decoding

Sophisticated FM/AM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset Editing)

◆ Multi-Functions for RDS Broadcast Reception

Other Features

◆ “SET MENU” which Provides You with 10 Items

for Optimizing This Unit for Your Audio/Video System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other Future

Formats

◆ 2 Optical/1 Coaxial Digital Signal Input Terminals

◆ SLEEP Timer

◆ Remote Control Capability

CONTENTS

INTRODUCTION

FEATURES .................................................................. 1

CONTENTS ................................................................. 1

GETTING STARTED ................................................. 2

CONTROLS AND FUNCTIONS ............................... 4

PREPARATION

SPEAKER SETUP....................................................... 8

CONNECTIONS.......................................................... 9

ADJUSTING THE SPEAKER BALANCE ............ 17

BASIC OPERATION

PLA YING A SOURCE .............................................. 19

DIGITAL SOUND FIELD PROCESSOR (DSP)

EFFECT .................................................................. 22

SOUND FIELD PROGRAM .................................... 23

TUNING ..................................................................... 26

RECEIVING RDS STATIONS................................. 30

RECORDING A SOURCE ON TAPE, MD OR

VIDEO CASSETTE ............................................... 33

ADVANCED OPERATION

SET MENU................................................................. 34

DELAY TIME AND SPEAKER

OUTPUT LEVELS ................................................. 38

SLEEP TIMER .......................................................... 40

INTRODUCTION PREP ARA TION

ADV ANCED OPERA

TION APPENDIX

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992 – 1997 Dolby Laboratories, Inc. All rights reserved.

APPENDIX

TROUBLESHOOTING ............................................ 41

SPECIFICATIONS.................................................... 44

GLOSSARY................................................................ 45

INDEX ........................................................................ 46

y indicates a tip for your operation.

EnglishBASIC OPERATION

GETTING STARTED

Checking the Package Contents

Check that the following items are included in your package.

Remote control Batteries (AA, R06, UM-3 type) 75-ohm/300-ohm antenna adapter

Indoor FM antenna

AM loop antenna

Battery Installation in the Remote Control

1 Turn the remote control over and slide the

battery compartment cover in the direction of the arrow.

Battery Replacement

If the remote control operates only when it is close to the unit, the batteries are weak. Replace all the batteries with new ones.

Notes

• Use only AA, R06 or UM-3 batteries for replacement.

• Be sure the battery polarity is correct. (See the illustration inside

the battery compartment.)

• Remove the batteries if the remote control will not be used for an

extended period of time.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

(U.K. model only)

Connection guide

2 Insert the batteries (AA, R06 or UM-3 type)

according the polarity markings on the inside of the battery compartment.

3 Close the battery compartment cover.

Using the Remote Control

Remote control sensor

Within approximately 6 m (20 feet)

GETTING STARTED

The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the infrared sensor during operation. When the sensor is covered or there is a large object between the remote control and the sensor, the sensor cannot receive signals. The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light (such as a fluorescent or strobe light). In this case, change the direction of the light or reposition the unit to avoid direct lighting.

Notes

• Handle the remote control with care.

• Do not spill water, tea or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– high humidity or temperature such as near a heater, stove or

bath; – dusty places; or – extremely low temperature.

INTRODUCTION PREP ARA TION

ADV ANCED OPERA

TION APPENDIX

EnglishBASIC OPERATION

CONTROLS AND FUNCTIONS

Front Panel

12 3 8 094 5 76

–

qwertyuiopa s d

1 STANDBY/ON

Press this switch to turn on the power of this unit or to set this unit in the standby mode. Before turning the power on, set VOLUME to the “m” position.

Standby mode

In this mode, this unit consumes a very small quantity of power to receive infrared-signals from the remote control.

2 Remote control sensor

This receives signals from the remote control.

3 Display

This shows various information. (Refer to page 6 for details.)

4 PTY SEEK MODE

Press this button to set the unit in the PTY SEEK mode.

5 RDS MODE/FREQ

When an RDS station is received, press this button to change the display mode among the PS mode, PTY mode, RT mode, CT mode (if the station offers those RDS data services) and/or frequency display mode in turn.

6 EON

Press this button to select the desired program type (NEWS, INFO, AFFAIRS, SPORT) when you want to tune in to a radio program of that type automatically.

7 PTY SEEK START

Press this button to begin searching for a station after the desired program type has been selected in the PTY SEEK mode.

8 INPUT MODE

Press this button to select the input mode between AUTO and ANALOG for the DVD/LD, TV/digital TV and satellite tuner sources.

9 INPUT

Turn this selector to select the input source (VCR, SAT/DTV, DVD/LD, TUNER, CD, AUX) that you want to listen to or watch. The name of the selected input source appears on the display.

0 VOLUME

Turn this control to turn up or down the volume.

CONTROLS AND FUNCTIONS

q PHONES jack

Connect the headphones to the PHONES jack. You can listen to the sound to be output from the main speakers through the headphones. When using headphones only, set both SPEAKERS A and B to the OFF position and press EFFECT to turn off the effect speakers (center and rear) (so that no DSP program indicator lights up on the display).

w SPEAKERS

Set A or B (or both A and B) to the ON position for the main speaker system (connected to this unit) that you want to use. Set the button(s) to the OFF position for the main speaker system that you don’t want to use.

e PROGRAM selector

Press l or h to select a DSP program when the effect speakers (center, rear and subwoofer) are turned on. The selected program indicator lights up on the display.

r EFFECT

Press this button to turn on or off the effect speakers (center and rear). If you turn them off, all Dolby Digital audio signals are directed to the right and left main speakers. In that case, the output levels of the right and left speakers may not match.

t Tone controls

These controls are only effective for the sound from the main speakers.

a) BASS

Turn this control clockwise to increase or counterclockwise to decrease the low-frequency response. The “0” position produces a flat response.

b) TREBLE

Turn this control clockwise to increase or counterclockwise to decrease the high-frequency response. The “0” position produces a flat response.

y TAPE/MD MON / EXT. DECODER

Press this button to select a tape or an MD source. The “TAPE/MD MONITOR” indicator lights up on the display. When you press the button next, the “TAPE/MD MONITOR” indicator goes off, “EXT. DECODER” appears on the display and you can listen to a source connected to the EXTERNAL DECODER INPUT terminals.

u BALANCE

This control is only effective for the sound from the main speakers. Turn the control to adjust the balance of the output volume from the right and left main speakers to compensate for sound imbalance caused by the speaker location or listening room conditions.

i A/B/C/D/E

Press this button to select one of a group (A to E) of preset stations.

o PRESET/TUNING

When “ z ” appears This button is used to select a preset station number (1 to 8). Press h to select a higher and l to select a lower preset station number. When “ z ” goes off This button is used for tuning. Press h to tune in to higher frequencies, and l to tune in to lower frequencies. When this unit is in the PTY SEEK mode, press this button to select a program type.

p PRESET/TUNING, EDIT

Press this button to turn on or off “ z ” on the display and switch the function between for storing a broadcasting station (preset tuning) and for tuning. This button is also used to exchange the assignment of two preset stations with each other.

a FM/AM

Press this button to switch the reception band between FM and AM.

s MEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations. Hold down this button for more than three seconds to begin automatic preset tuning.

d TUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode between automatic and manual. To use the automatic tuning method, press this button so that the “AUTO” indicator lights up on the display. To use the manual tuning method, press this button so that the “AUTO” indicator goes off.

INTRODUCTION PREP ARA TION

ADV ANCED OPERA

TION APPENDIX

EnglishBASIC OPERATION

CONTROLS AND FUNCTIONS

Display

1 t indicator

The “t” indicator lights up when the built-in DTS decoder is turned on.

2 DSP program indicators

The name of the selected DSP program lights up in the following cases:

• When the tuner is selected as the input source.

• When DSP program No. 2, 3 or the subprogram “ENHANCED” of No.1 is selected.

3 Multi-information display

This display shows various information: for example the name of the selected DSP program and the various settings during adjustment with the SET MENU. The current station frequency and band (FM or AM) also appear when the tuner is selected as the input source.

4 Input source indicators

One of the arrows for these indicators lights up depending on which source is selected.

5 TAPE/MD MONITOR indicator

This lights up when the tape deck or MD recorder, etc. is selected as the input source by pressing TAPE/MD MON / EXT. DECODER (or TAPE/MD).

6 g and o indicators

“ g ” lights up when the built-in Dolby Digital decoder is on and the signals of the selected source are encoded with Dolby Digital. “ o ” lights up when the built-in Dolby Pro Logic decoder is on.

7 x indicator

“ x ” lights up when the built-in digital sound field processor is on.

8 MEMORY indicator

This flashes for about five seconds after pressing MEMORY. During this period, the displayed station can be stored in the memory.

9 RDS mode indicators

The name(s) of the RDS data offered by the currently received RDS station light(s) up. Illumination of the red indicator next to the RDS data name shows that the corresponding RDS mode is now selected.

0 AUTO indicator

This lights up when the unit is in the automatic tuning mode.

q PTY HOLD indicator

This lights up while searching for stations in the PTY SEEK mode.

w EON indicator

This lights up when an RDS station that offers the EON data service is being received.

e Program type name indicators

The name of the selected program type lights up when the “EON” indicator lights up.

r STEREO indicator

This lights up when an FM stereo broadcast with sufficient signal strength is being received.

t Signal-level indicator

This indicates the signal level of the station being received. If multipath interference is detected, the indication decreases.

y SLEEP indicator

This lights up while the built-in SLEEP timer is on.

Remote Control

CONTROLS AND FUNCTIONS

The provided remote control is designed to control all most commonly used functions of this unit. If a YAMAHA tape deck or CD player designed for remote control compatibility is connected to this unit, this remote control can also control various functions of that component.

3 4

8 9

5 A/B/C/D/E, PRESET +/–

These buttons are used to select a preset station. A/B/C/D/E: To select one of a group (A to E) of preset

stations

PRESET +/–: To select a preset station number (1 to 8)

6 SLEEP

Press this button to set the SLEEP timer.

7 VOLUME

These buttons are used to adjust the volume level.

: To turn up the volume : To turn down the volume

8 SET MENU

Press this button to select the items in the SET MENU.

9 DSP PRG+, PRG–

Press these buttons to select a DSP program.

0 EFFECT

Press this button to turn on or off the effect speakers (center and rear).

q Input selector buttons

These buttons select the input source. CD: To play a CD TUNER: To listen to an FM (RDS) or AM broadcast TAPE/MD: To play a tape or MD DVD/LD: To play a DVD or LD SAT/D-TV: To watch a TV or satellite broadcast VCR: To play a video cassette AUX: To use another audio component

INTRODUCTION PREP ARA TION

ADV ANCED OPERA

■ Controlling this unit

1 POWER

Each time you press this button, the unit switches between the power on and standby mode.

2 TIME/LEVEL

Press this button to select the item in the TIME/LEVEL mode.

3 +/–

These buttons adjust the settings of the SET MENU and TIME/LEVEL mode.

4 TEST

Press this button to output the test tone for each speaker.

w EXT. DEC.

Press this button to select another multi-channel source.

■ Controlling a YAMAHA tape deck or

CD player

Identify the remote control buttons with your component’s buttons. If these buttons are identical, their functions will be the same. Refer to the instructions for each button function supplied with your component.

! Tape deck buttons

These buttons are used for controlling a tape deck.

• DECK A/B, DIR A and DIR B are only available for a double cassette tape deck.

• For a single cassette tape deck with an automatic reverse function, press DIR A to reverse the direction of tape running.

@ CD player buttons

These buttons are used for controlling a CD player

• DISC SKIP is only available for a CD player with a CD changer.

TION APPENDIX

EnglishBASIC OPERATION

PREPARATION

SPEAKER SETUP

Speakers to Be Used

This unit is designed to provide the best sound-field quality with a 5-speaker system, using main speakers, rear speakers and a center speaker. If you use different brands of speakers (with different tonal qualities) in your system, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacture or speakers with the same tonal quality.

The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use highperformance models that can reproduce sounds over the full range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low frequency effect) channel with high fidelity when playing back a source encoded with Dolby Digital. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction.

Speaker Placement

Refer to the following diagram when you place the speakers.

Main speaker (L)

Center speaker

■ Main speakers

Place the right and left main speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the TV monitor should be the same.

■ Rear speakers

Place these speakers behind your listening position, facing slightly inwards, nearly 1.8 m (approx. 6 feet) above the floor.

■ Center speaker

Align the front face of the center speaker with the front face of your TV monitor. Place the speaker as close to the monitor as possible, such as directly over or under the monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the sound will be heard from the right and left main speakers. In that case, “CENTER SP” in the SET MENU is set to the NONE position. (Refer to page 35 for details.)

Main speaker (R)

Rear speaker (R)

Subwoofer

1.8 m

Rear speaker (L)

■ Subwoofer

The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce the wall reflections.

CAUTION

Some types of speakers interfere with a TV monitor. If this problem occurs, move the speakers away from the monitor. If you cannot avoid installing the center speaker or subwoofer near the TV monitor, use magnetically shielded speakers.

CONNECTIONS

V V

C C

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been completed.

Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different terminal names. Refer to the instructions for each component to be connected to this unit.

When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products.

Use RCA-type pin plug cables for connecting audio/video components with the exception described later.

The input and output terminals for pin plugs can be distinguished as follows:

Yellow video signals (composite)

White analog audio signals for the left channel

Red analog audio signals for the right channel

coaxial digital signals

After completing all connections, check them again to make sure they are correct.

INTRODUCTION

PREP ARA TION

Connecting the Antenna (page 10)

Connecting an Audio Component (page 12)

Connecting to an External Decoder (page 12)

Connecting a Video Component (page 13)

Connecting Speakers (page 14)

MAIN

––++

REAR

CENTER

(SURROUND)

–

IMPEDANCE SELECTOR switch (page 16)

Connecting the Power Supply Cords (page 16)

SET BEFORE POWER ON

MAIN A OR B:4ΩMIN. /SPEAKER A + B:8ΩMIN. /SPEAKER CENTER : 6ΩMIN. /SPEAKER REAR :6ΩMIN. /SPEAKER

MAIN A OR B:8ΩMIN. /SPEAKER A + B:I6ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER REAR :8ΩMIN. /SPEAKER

–

(Europe model)

MAINS

100W MAX. TOTAL

SWITCHED

ADV ANCED OPERA

TION APPENDIX

EnglishBASIC OPERATION

CONNECTIONS

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. However, a properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality.

Connect each antenna correctly to the designated terminals.

■ Indoor FM antenna (included)

Firmly insert the connector into the FM ANT terminal. The

Indoor FM antenna

■ Outdoor FM antenna

75-ohm/300-ohm antenna adapter (included for U.K. model)

75-ohm coaxial cable

75-ohm/300-ohm antenna adapter (included for U.K. model)

300-ohm feeder

indoor FM antenna is only a simple antenna. For reception with better sound quality, installing the outdoor FM antenna (commercially available) is recommended.

Note

• Do not connect an outdoor FM antenna and the indoor FM antenna at the same time.

You may be unable to obtain good FM radio reception depending on your local conditions (distance from the broadcasting station, interposing buildings and mountains, etc.). Consult your dealer or authorized service center and be sure to install an antenna that suits your local conditions. Install the outdoor FM antenna (commercially available) in a high place as far away from any roads as possible to avoid being affected by automobile ignition noise.

■ Connecting a coaxial cable to the included 75-ohm/300-ohm antenna

adapter (U.K. model only)

Cover

11 (7/16)

8 (5/16) 6 (1/14)

Unit: mm (inch)

1 Open the cover of the included 75-ohm/

300-ohm antenna adapter.

2 Cut the external sleeve of the 75-ohm coaxial

cable and prepare it for connection.

3 Cut the lead wire and remove it. 4 Insert the cable wire into the slot, and clamp it

Lead wire

with pliers.

5 Snap the cover into place.

Clamp with pliers.

Insert the wire into the slot.

■ AM loop antenna (included)

AM loop antenna

■ Connecting the AM loop antenna

CONNECTIONS

The AM loop antenna can be removed from the stand and attached to a wall, etc. However, note that the reception sensitivity may deteriorate if the antenna is attached to a metal or steel reinforced wall.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

INTRODUCTION

Antenna stand

■ Outdoor AM antenna

Vinyl covered wire (5 m to 10 m)

■ Ground (GND terminal)

1 Press the tab and unlock the terminal hole. 2 Insert the AM loop antenna lead wires into the

AM ANT and GND terminals.

PREP ARA TION

3 Return the tab to its original position to lock

the lead wires. Lightly pull the lead wires to confirm a good connection.

4 Attach the loop antenna to the antenna stand. 5 Orient the AM loop antenna so that the best

reception is obtained.

If you cannot obtain good reception with the AM loop antenna, connect 5 m to 10 m of vinyl covered wire to the AM ANT terminal and extend it outdoors from a window.

ADV ANCED OPERA

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

TION APPENDIX

EnglishBASIC OPERATION

CONNECTIONS

Connecting an Audio Component

(Europe model)

L R L R L R

Be sure to connect the right channel (R), left channel (L), input (IN) and output (OUT) properly.

Analog signal

OUTPUT LINE OUT LINE IN

CD player

Tape deck or MD recorder

Connecting to an External Decoder

External decoder

MAIN OUT

L R L R

SURROUND OUT

CENTER OUT

SUBWOOFER OUT

(Europe model)

Signal flow

This unit has additional 6-channel audio signal input terminals for connecting an external decoder to this unit. Connect the 6-channel audio signal output terminals of the decoder to the EXTERNAL DECODER INPUT terminals of this unit.

Notes

• When a source connected to these terminals is selected, the digital

sound field processor cannot be used.

• The settings of “CENTER SP”, “REAR SP”, “MAIN SP” and

“BASS OUT” in the SET MENU have no effect on a source connected to these terminals. The setting of “MAIN LVL” is effective. (Refer to pages 35 and 36 for details.)

Connecting a Video Component

DVD/LD player TV/digital TV, satellite tuner, cable TV

ANALOG AUDIO OUT

VIDEO OUT

COAXIAL DIGITAL OUT

OPTICAL DIGITAL OUT

VIDEO OUT

ANALOG AUDIO OUT

CONNECTIONS

INTRODUCTION

L R

(Europe model)

L R

AUDIO OUT

L R V V

AUDIO IN

VIDEO OUT

VCR

■ Audio signal terminals

Be sure to connect the right channel (R), left channel (L), input (IN) and output (OUT) properly.

■ Video signal terminals

Be sure to connect the input (IN) and output (OUT) properly.

■ Digital audio signal terminals

If your DVD/LD player, TV/digital TV or satellite tuner, etc. has coaxial or optical digital signal output terminals, they can be connected to this unit’s COAXIAL and/or OPTICAL digital signal input terminals. To make a connection between the optical digital signal terminals, remove the cover from each terminal, and then connect them by using a commercially available optical fiber cable that conforms to EIA standards. Other cables might not function correctly.

L R

Analog signal

Video signal

No connection

Digital signal

(optical)

Digital signal (coaxial)

VIDEO IN

SCART-plug

VIDEO IN

Signal flow

TV monitor

■ TV monitor with a 21-pin connector

Make a connection as shown above with a commercially available SCART-plug connector cable.

Notes

• Be sure to attach the covers when the OPTICAL terminals are not being used in order to protect them from dust.

• If your LD player has a Dolby Digital RF signal output terminal, be sure to use the RF demodulator (separately purchased).

• No sound will be heard when connecting your LD player’s Dolby Digital RF signal output terminal directly to this unit’s COAXIAL DVD/LD digital signal input terminal.

• The input signal from the DVD/LD input terminals is selected in the following order of priority with the input mode set to AUTO: COAXIAL terminal → OPTICAL terminal → Analog terminal. Refer to page 21 for details.

• All digital signal input terminals are applicable to sampling frequencies of 32 kHz, 44.1 kHz and 48 kHz.

PREP ARA TION

ADV ANCED OPERA

TION APPENDIX

When making connections between the digital signal terminals, you should connect the components to the samenamed analog audio signal terminals of this unit, because a digital signal cannot be recorded by a tape deck, MD recorder or VCR connected to this unit.

EnglishBASIC OPERATION

+ 35 hidden pages