Yamaha DTX700 User Manual

Read on your computer

(PDF file)

DRUM TRIGGER MODULE

DTX700

Read first

Owner’s Manual

(Setup / Basic Operation)

This booklet

Reference Manual

(Detailed Operation)

Read when necessary

Data List :

Separate booklet

Please download from this web page: http://www.yamaha.co.jp/manual/

Read on paper

Owner’s Manual

(Setup / Basic Operation)

(see page 6 for Table of Contents)

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha.

This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please observe all safety markings and instructions that accompany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units.

This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before damage occurs.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of bat- tery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement.

This product may also use “household” type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that the charger is intended for the battery being charged.

When installing batteries, never mix old batteries with new ones, and never mix different types of bat rectly. Mismatches or incorrect installation may result in overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all batter- ies away from children. Dispose of used batteries promptly and as regu- lated by the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.

teries. Batteries MUST be installed cor-

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model num- ber, serial number, power requirements, etc., are located on this plate.

Yo u should record the model number, serial number, and the date of pur- chase in the spaces provided below and retain this manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

92-BP (bottom)

PLEASE KEEP THIS MANUAL

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or

another product use only high quality shielded cables. Cable/s sup- plied with this product MUST be used. Follow all installation instruc- tions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guar-

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Drum Trigger Module

Model Name : DTX700

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC)

antee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measure

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interfer- ence that may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

DTX700 Owner’s Manual

PRECAUTIONS

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor

Location

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.

• Only use the voltage specified as correct for the instrument. The required voltage is printed on the name plate of the instrument.

• Use the specified adaptor (page 57) only. Using the wrong adaptor can result in damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.

• This instrument contains no user-serviceable parts. Do not attempt to disassemble or modify the internal components in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet conditions, place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the instrument, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.

• When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. Then have the device inspected by Yamaha service personnel.

• The power cord or plug becomes frayed or damaged.

• It emits unusual smells or smoke.

• Some object has been dropped into the instrument.

• There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet.

• When removing the electric plug from the instrument or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical storms.

DMI-3 1/2

• Do not place the instrument in an unstable position where it might accidentally fall over.

• Before moving the instrument, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet.

DTX700 Owner’s Manual

• Use only the stand/rack specified for the instrument. When attaching

Connections

Handling caution

the stand or rack, use the provided screws only. Failure to do so could cause damage to the internal components or result in the instrument falling over.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel. This could cause physical injury to you or others, damage to the instrument or other property, or operational failure.

• Do not rest your weight on, or place heavy objects on the

• Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level.

instrument, and do not use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use. Even when the power switch is in standby status, electricity is still flowing to the instrument at the minimum level. When you are not using the

instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

NOTICE

To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation. (Verified operating temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• When cleaning the instrument, use a soft, dry/dry or slightly damp cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

 Saving data

• Saved data may be lost due to malfunction or incorrect operation. Save important data to a USB storage device/external device such as a computer.

• To protect against data loss through media damage, we recommend that you save your important data onto two USB storage devices/external media.

Information

 About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

 About this manual

• The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

DTX700 Owner’s Manual

DMI-3 2/2

Welcome

Thank you for purchasing the Yamaha DTX700 Drum Trigger Module.

To get the most out of your new instrument, be sure to read this owner’s manual carefully.

And after reading through this manual, be sure to store it in a safe place so

that you can refer back to it again as needed.

Using the Manuals

Owner’s Manual – this booklet (Setup / Basic Operation)

This paper manual describes the basic operations performed via the DTX700’s control panel.

Data List

The Data List contains the names of all of the DTX700’s sounds and kits, together with MIDI-related reference material.

Reference Manual (Detailed Operation) *Not bundled with this product.

The Reference Manual provides a description of all of the functions that can be accessed by pressing the [MENU] button on the DTX700’s control panel. This PDF manual is not bundled with the drum trigger module. If you wish to learn more about your DTX700 using the Reference Manual, please download it from the Yamaha Manual Library web page:

http://www.yamaha.co.jp/manual/

* Yamaha Corp. reserves the right to modify this URL at any time without prior notice.

Using PDF Manuals

The Reference Manual for your DTX700 is made available in digital format as a PDF document. As such, a computer and suitable software will be required in order to read it. We recommend that Adobe Reader be used for this purpose as it allows you to quickly and easily search for keywords, to print out specific sections, and to conveniently jump from page to page by clicking embedded links. Keyword searching and link-based navigation in particular are extremely useful functions available only with digital-type documents. The most-recent version of Adobe Reader can be downloaded from the following web page.

http://www.adobe.com/products/reader/

Bundled items

• Power adaptor • Module holder

• Owner’s Manual (this booklet) • Module-holder fixing screws x 4

• Data List

• DVD-ROM (containing DAW software)

 Latest Firmware Version

From time to time, Yamaha may update product firmware without prior notice. We recommend, therefore, that you check our web site (below) for the latest version and keep your DTX700 firmware up to date.

http://dtxdrums.yamaha.com/downloads/

The content of this Owner’s Manual applies to the newest version of the firmware as of printing. Details regarding any functions

ded to later versions will also be made available via the above web site.

 Optional Pads

Within this Owner’s Manual, the optional external pads that may be connected to the DTX700 are referred to by model name. Please note that these model names were up-to-date as of printing of this manual. Details regarding any subsequently released models will be made available via the following web site.

http://dtxdrums.yamaha.com/downloads/

DTX700 Owner’s Manual

Welcome ................................................................5

Using the Manuals ................................................5

Bundled items .......................................................5

Contents.................................................................6

First Steps.................................................7

Quick Start Guide .....................................8

Setup

Component Names & Functions........................10

Control Panel............................................................. 10

Side Panel..................................................................11

Rear Panel ................................................................ 12

Setting Up for Sound ..........................................13

Connecting the Adaptor............................................. 13

Connecting Speakers or Headphones ...................... 13

Connecting a Music Player........................................ 13

Turning On................................................................. 14

Turning Off................................................................. 14

Auto Power-Off........................................................... 14

Basic Operation

Playing Demo Songs ..........................................16

Basic DTX700 Operations ..................................17

Dial (with integrated button)....................................... 17

Changing the Cursor Value ....................................... 17

Moving the Cursor ..................................................... 17

[-/DEC] and [+/INC] Buttons ...................................... 18

[F1], [F2] & [F3] Function Buttons.............................. 18

Adjusting the Volume................................................. 19

Adjusting Display Contrast ........................................ 19

Storing Settings ......................................................... 21

Connecting a USB Memory Device........................... 21

Restoring Default Settings......................................... 22

Playing Drum Pads..............................................23

Snares & Toms ..........................................................23

Hi-Hats ......................................................................23

Cymbal ...................................................................... 24

Performing on Many Different Kits ....................25

Selecting a Kit ........................................................... 25

Selecting a Sensitivity for the Entire Kit..................... 26

Adjusting Tone........................................................... 27

Turning Off Effects..................................................... 28

Initializing a Kit .......................................................... 28

Switching the Display Mode ......................................29

Building Your Own Kit........................................ 30

Selecting Sounds (Instruments) ................................30

Adjusting an Instrument’s Sound............................... 31

Playing with a Double Bass Drum ............................. 32

Importing & Assigning Audio Files.............................32

Naming an Original Kit ..............................................34

Adjusting the Snare Wire........................................... 35

Playing with Songs for Practice........................ 36

Playing a Song ..........................................................36

Adjusting the Song Volume ....................................... 36

Adjusting the Volume of a Song’s Drums ..................37

Muting the Drum Part ................................................ 38

Soloing the Bass Part................................................38

Locking a Kit..............................................................39

Turning On the Click-Track................................ 41

Setting the Tempo and Starting the Click-Track......... 41

Setting the Click-Track Volume .................................. 41

Setting the Time Signature........................................ 43

Using the Timer......................................................... 44

Tap Tempo – Setting the Tempo by Playing Pads......44

Using DTX700 Training Functions .............................45

Recording Your Performances .......................... 48

Recording a Performance.......................................... 48

Playing a Recorded Performance..............................48

Deleting a Recorded Performance ............................ 48

Recording Performance & Song Together ................. 49

Integrating Accessories..................................... 50

Using an HH65 Hi-hat Controller

as Kick Drum Pedal...............................................50

Expanding with a PCY135 Cymbal Pad..................... 50

Connecting Your DTX700 to a Computer ......... 52

Making Connections..................................................52

Making Music with a Computer .................................53

Setting up Cubase Remote Control...........................54

On-Screen Messages ......................................... 55

Troubleshooting ................................................. 56

Specifications ..................................................... 57

Index .................................................................... 58

List of DTX700 Functions .................................. 59

* For details regarding these functions, refer to the Reference

Manual PDF document.

DTX700 Owner’s Manual

First Steps

123

Open the boxes to reveal their contents.

• DTX700 Drum Trigger Module (main unit)

• Racks such as the RS500 and RS700

• Pad sets such as the DTP700C, DTP700P, DTP750C, and DTP750P

Assemble your kit.

• Assemble the racks.

m Refer to the assembly manuals that came with your racks

(RS500, RS700, etc.).

•Mount the pads and the DTX700 on the racks.

m Refer to the assembly manuals that came with your pad

sets (DTX700K, DTX750K, etc.).

Connect your kit.

• Connect your pads to the DTX700 using the correct cables.

m Refer to the assembly manuals that came with your pad

sets (DTX700K, DTX750K, etc.).

•Plug the power adaptor into the DTX700 and turn it on.

m See page 13 of this booklet.

Play your kit.

• See pages 8 and 9 of this booklet for tips on getting started right away.

•This booklet provides an introduction to your DTX700’s basic functions. Detailed descriptions of all functions can be found in the Reference Manual PDF document (see page 5).

DTX700 Owner’s Manual

Quick Start Guide

Choosing sounds to play (page 25 of Basic Operation)

Playing along with a song (page 36 of Basic Operation)

q Press the [KIT] button. w Turn the dial to select new

sounds.

Yo u can also assign sounds individually to each of the pads (page 25 of Basic Operation).

DTX700 Owner’s Manual

q Press the [SONG] button. w Turn the dial to select a new song. e Press the [F3] button to start the

song.

Yo u can press the [F2] button to silence the song’s drum part (page 38 of Basic Operation).

Quick Start Guide

Practicing with a metronome (page 41 of Basic Operation)

Recording your own performance (page 48 of Basic Operation)

q Press the [CLICK] button. w Turn the dial to set the tempo. e Press the [ ] button to start the

metronome.

q Press the [REC] button. w Press the [>/] button to start

recording.

e When you have finished playing,

press the [>/] button once again to stop recording.

Yo u can also use the [>/] button to start and stop playback of your recorded performance (page 48 of Basic Operation).

DTX700 Owner’s Manual

Setup

!8 !9

Component Names & Functions

Control Panel

q [PHONES] volume knob (page 13)

This knob controls the volume of audio output from the [PHONES] jack. Turn clockwise to increase the volume or counter-clockwise to decrease it.

w [MASTER] knob (page 19)

This knob controls the DTX700 master volume (i.e., the volume at the OUTPUT jacks). Turn clockwise to increase the volume or counter-clockwise to decrease it.

e Display (page 29)

This LCD screen shows information and data needed to operate the DTX700.

r Dial (page 17)

This dial can be both turned and pressed.

• By pressing it, you can set parameter values and

• By turning it, you can move the cursor within dis-

DTX700 Owner’s Manual

execute various functions such as the storing of data.

played pages and change the currently selected parameter value.

t (Standby/On) button (page 14)

Use this switch to turn your DTX700 on and off.

y [F1], [F2], and [F3] function buttons (page 18)

These buttons are used to access a range of different functions depending on the page displayed.

u [EXIT] button

Press t his button to cancel operations such as the copying and storing of data. In addition, you can immediately silence all voices at any time by holding down the [SHIFT] button and pressing the [EXIT] button.

i [STORE] button (page 21)

This button is used to store settings and other data in the DTX700’s internal memory. In addition, it will light

up whenever parameter settings have been changed but not yet stored.

o [KIT] button (page 25)

This button is used to access the Kit page in order to select a drum kit.

Component Names & Functions

Setup

!0 [SONG] button (page 36)

This button is used to access the Song page in order to select a song.

!1 [MENU] button (page 20)

This button is used to access the Menu area. From here, you can select various other pages in order to configure your DTX700 in many different ways.

*This booklet introduces some of the basic functions avail-

able in the Menu area. For a complete description of all functions, please download the DTX700 Reference Manual from this web page:

http://www.yamaha.co.jp/manual/

!2 [INST] button (page 30)

This button is used to access the Instrument page in order to select instruments.

[Definition] Instrument

In the context of the DTX700, the term “instru- ment” is used to refer to each of the various percussion instruments that make up a kit. Typical examples would be snare drums, tom-toms, cymbals, and kick drums.

!3 [CLICK] button (page 41)

This button is used to access the Click page in order to set your DTX700’s click-track (or metronome).

!5 [>/] button (page 48)

Use this button to start and stop the playback of performances that you have recorded on the DTX700.

!6 [REC] button (page 48)

Using this button, you can activate and deactivate recording of your performances.

!7 [ ] (Click-track) button (page 41)

The Click-track button is used to start and stop the DTX700’s click-track (or metronome).

!8 [-/DEC] button (page 18)

This button is used to decrease the value at the cursor position. In addition, the selected value can be decreased in units of 10 by holding down the [SHIFT] button and pressing the [-/DEC] button or by holding down the [-/DEC] button and pressing the [+/INC] button.

!9 [+/INC] button (page 18)

This button is used to increase the value at the cursor position. In addition, the selected value can be increased in units of 10 by holding down the [SHIFT] button and pressing the [+/INC] button or by holding down the [+/INC] button and pressing the [-/DEC] button.

!4 [SHIFT] button

When you press this button, the functions assigned to the [F1], [F2], and [F3] buttons will change. These functions can be accessed by holding down the [SHIFT] button and pressing the corresponding function button (see page 18). Meanwhile, a number of the buttons on the DTX700’s control panel have secondary functions, indicated just above the buttons themselves. These functions can also be accessed by holding down the [SHIFT] button and pressing the corresponding button.

Side Panel

@0 Sliders (page 41)

The sliders are used to adjust the volumes of individ-

ual parts such as the snare and toms, and also the vol- ume of the click-track.

q [USB TO HOST] port (page 52)

This port is used to connect the DTX700 to a computer via a USB cable.

w [USB TO DEVICE] port (page 21)

This port is used to plug in a USB memory device (such as a flash drive), either directly or via a USB cable.

DTX700 Owner’s Manual

Setup

w ert uyq

!1 !0 o

Component Names & Functions

Rear Panel

q [LCD CONTRAST] knob (page 19)

This knob is used to set the display contrast for optimum legibility.

w [ ] connector (page 13)

Use this connector for the power adaptor that came with your DTX700.

e Cord clip (page 13)

Wrap the power adaptor cord around this clip to pre- vent accidental unplugging during operation.

r MIDI [IN] and [OUT] connectors (page 13)

The MIDI [IN] connector is used to receive control or performance data from another MIDI device, such as an external sequencer, via a MIDI cable. When con- nected in this way, you can play the DTX700’s internal tone generator and control many of its parameters using another MIDI device. Meanwhile, the MIDI [OUT] connector is used to send performance data from the DTX700 to other devices in the form of MIDI messages.

t [AUX IN] (auxiliary input) jack (page 13)

External audio signals can be input via this stereo mini-jack. Using [AUX IN], you can connect a portable music player, a CD player, or another similar device to play along with your favorite tunes.

y OUTPUT [L/MONO] and [R] jacks (page 13)

Use these jacks to output line-level stereo mixes from your DTX700. For example, you can connect each of the jacks to the left and right inputs of an external stereo amplifier or mixer using mono audio-jack cables. For mono output, use the [L/MONO] jack only.

i Trigger input jacks [qSNARE] to [iHI-HAT],

and [!1]

These trigger-input jacks are used to connect stereotype pads (two- and three-zone). They also support standard mono-output pads. In addition, these triggerinput jacks are compatible with pad controllers.

o [HI-HAT CONTROL] jack

This jack is used to connect an HH65 Hi-hat Controller or an RHH135 Real Hi-hat Pad via its control output.

!0 Trigger input jack [oKICK/!0]

This trigger-input jack is used to connect mono-type pads such as the KP65 Kick Pad. If using a KP65, fur- thermore, you can use the input jack on its rear sur- face to connect an additional mono-type pad. Meanwhile, you could also use a Y-shaped cable (sold separately) with this jack in order to connect a pair of mono-type pads.

!1 Trigger input jack [!2HH-KICK]

This jack is used to connect an HH65 Hi-hat Controller (sold separately) for use as an alternative kick pad or as part of a double bass drum configuration (page 50).

u [PHONES] jack (page 13)

Use this standard audio jack to connect a pair of stereo headphones.

DTX700 Owner’s Manual

Setup

Cord clip

Power adaptor cord

Speakers with

a built-in amplifier

External MIDI device

MIDI OUT

Standard stereoaudio jack (6.3-mm dia.)

Mini stereo audio cable (3.5-mm dia.)

Mobile music

player, etc.

Standard mono audio

cable (6.3-mm dia.)

MIDI

cable

MIDI

Setting Up for Sound

Connecting the Adaptor

1 Ensure that your DTX700 is turned off (i.e.,

the screen is not lit).

2 Insert the power adaptor’s DC plug into the

[ ] connector on the rear panel.

3 Hook the power adaptor’s cord around the

cord clip to secure it in place.

CAUTION

• Excessive bending can damage the power adaptor’s cord and create a fire hazard. Ensure, therefore, that the power cord is not bent at an extreme angle when wrapped around the clip.

4 Plug the power adaptor’s AC power cord into

an AC wall socket or another electrical outlet.

WARNING

• Use only the power adaptor that came with your DTX700.

Connecting Speakers or Headphones

Your DTX700 does not come with built-in speakers. In order to hear it, therefore, you will need to connect headphones or a DTX-series monitor system, such as the MS40DR.

 Connecting Speakers

Connect your speakers to the OUTPUT [L/MONO] and [R] jacks (standard mono-audio).

 Connecting Headphones

Connect your headphones to the [PHONES] jack (standard stereo-audio). The [PHONES] knob on the control panel can be used to adjust the volume of the headphones.

CAUTION

• To prevent hearing loss, avoid using headphones at high volumes for extended periods of time.

Connecting a Music Player

You can connect a portable music player or another similar source of audio to your DTX700 via the [AUX IN] (auxiliary input) stereo mini-jack. This makes it possible to play along with your favorite songs.

CAUTION

• The DTX700 remains charged and draws a small amount of power even when the (Standby/On) button is set to the Standby position. For this reason, you should always unplug the power adaptor from the wall socket if the instrument will not be used for an extended period of time.

NOTICE

• Whenever connecting other devices, ensure that the cables you use have plugs that match the input or output connectors on those devices.

• Before making connections, furthermore, you should also turn the volume on the other devices fully down.

• When all connections have been made, use each device’s volume controller to balance its output with that of the DTX700.

DTX700 Owner’s Manual

Setup

Setting Up for Sound

Turnin g On Turnin g Off

1 Press the (Standby/On) button.

The display will turn off.

NOTICE

• If you turn off the DTX700 without storing any changes you have made to settings, those changes will be lost. For details on how to store changed settings, see page 21.

1 Turn the [MASTER] knob fully counterclock-

wise to minimize the output volume.

Auto Power-Off

2 Press the (Standby/On) button.

The opening pages will be displayed, followed by the Kit page.

If no controls are operated or no data is exchanged with external devices (such as a computer or MIDI instrument) for a predetermined length of time, your DTX700 will turn off automatically. This function is called Auto Power-Off.

NOTICE

• If you do not store changed settings before the Auto Power-Off function activates, your changes may be permanently lost. Be sure, therefore, to store new settings whenever you are happy with them.

3 If you have connected any amplified speakers

or other similar external devices, turn them on now.

NOTE

• When powering down your system, be sure to turn off external devices before the DTX700.

 Setting the Auto Power-Off Function

Use the following procedure to set the time until the Auto Power-Off function activates or to disable the function.

1 Press the [MENU] button.

2 Turn the dial to move the cursor to “Utility”.

3 Press the dial.

4 Turn the dial to move the cursor to “General”.

DTX700 Owner’s Manual

5 Press the dial.

6 Turn the dial to move the cursor to the “Auto-

PowerOff” row of the displayed list.

Setting Up for Sound

Setup

7 Press the dial.

The cursor will zoom in on the value on the right.

8 Turn the dial to set the automatic power-off

time.

The value indicates the idle time until automatic power-off in minutes. Settings can be made in units of 5 minutes between 5 and 30. Furthermore, you can disable the Auto Power-Off function by selecting “off”.

9 Press the dial.

The cursor will zoom out to select the entire row.

11 Press the dial to store your new settings.

NOTE

• The Auto Power-Off function is set to 30 minutes by default.

 Disabling the Auto Power-Off Function at

Startup

To disable the Auto Power-Off function when turning on the DTX700, hold down the [>/

(Standby/On) button. (This action sets the AutoPower-

Off parameter to “Off”.)

] button when you press the



10 Press the [STORE] button.

DTX700 Owner’s Manual

Basic Operation

Playing Demo Songs

Your DTX700 comes pre-programmed with demo songs. Played as described below, these songs allow you to fully appreciate the quality of the sound produced by the built-in tone generator.

1 Press the (Standby/On) button to turn on

your DTX700.

Startup pages

4 Press the [F3] button once again to stop the

demo song.

5 To select a different demo song, turn the dial

and repeat Steps 3 and 4.

2 Press the [SONG] button.

3 Press the [F3] button.

The demo song indicated on the display will start. The [SONG] button will flash while the song is playing.

DTX700 Owner’s Manual

Basic Operation

Dial

Cursor

Press the dial to switch to the underline cursor.

Cursor

Turn the dial to move the underline

Basic DTX700 Operations

Dial (with integrated button)

 Pressing the dial

You press the dial to execute various operations and to set new values for parameters. The cursor type (see below) can also be toggled by pressing the dial.

 Turning the dial

Moving the Cursor

When a page contains more than one editable value, you can press the dial to toggle between inverted text and underlined text at the cursor position.

Example: After pressing the [SONG] button

On the page accessed with the [SONG] button, you can set both the song number and the tempo .

By turning the dial, you can move the cursor. In this way, you can select the value you wish to change.

Changing the Cursor Value

The cursor is displayed as a block of inverted text.

By turning the dial in either direction, you can change the value at the current cursor position.

You turn the dial to change parameter values and to move the cursor.

Press the dial once again to switch back to the inverted-text cursor.

By turning the dial in either direction, you can change the value at the cursor position.

DTX700 Owner’s Manual

Basic Operation

Function buttons

Kit Lock

Effects Switch

Display Mode

Basic DTX700 Operations

[-/DEC] and [+/INC] Buttons [F1], [F2] & [F3] Function Buttons

These buttons are used to change the currently selected value. Press the [+/INC] button to increase the value by one; the [-/ DEC] button to decrease by one. If you hold down either button, the value will change continuously. In the case of parameters with a wide range of possible settings, you can increase them in units of 10 by holding down the [SHIFT] button and pressing the [+/INC] button or by holding down the [+/INC] button and pressing the [-/DEC] button. Similarly, you can decrease in units of 10 by holding down the [SHIFT] button and pressing the [-/DEC] button or by holding down the [-/DEC] button and pressing the [+/INC] button.

The functions that you can access by pressing the [F1], [F2], and [F3] function buttons are displayed as inverted text at the bottom of the display. In addition, when the symbol is shown in the bottom right corner, you can press the [SHIFT] button to display additional functions for each of the buttons.

To access these additional functions, hold down the [SHIFT] button and press the corresponding button.

DTX700 Owner’s Manual

Adjusting the Volume

[LCD CONTRAST] knob

You can use the [MASTER] knob to adjust the volume of sound on the OUTPUT [L/MONO] and [R] channels. In addition, the [PHONES] knob can be used to adjust the volume of headphones plugged into the [PHONES] jack on the rear panel. Turn clockwise to increase the volume or counter-clockwise to decrease it.

Adjusting Display Contrast

Basic DTX700 Operations

Basic Operation

Using the [LCD CONTRAST] knob on the rear panel, you can adjust the contrast level of the DTX700 display.

DTX700 Owner’s Manual

Basic Operation

Basic DTX700 Operations

Pages Accessed Using the [MENU] Button

The pages of your DTX700’s Menu area provide access to a wide range of highly-useful settings. To access this area, simply press the [MENU] button. This manual introduces some of the pages from the Menu area. For a complete description, please download the DTX700 Reference Manual from this web page:

http://www.yamaha.co.jp/manual/

 Cursor operations on Menu area pages

The way in which the cursor is displayed and operated on Menu area pages differs from that of other pages.

• Navigation pages

When you turn the dial on navigation-type pages, the cursor (i.e., the inverted text) moves in the corresponding direction.

By pressing the dial, you can move one level further into the Menu area.

• Parameter pages

When you turn the dial on parameter-type pages, the cursor (i.e., the inverted text) moves up and down within the displayed list.

When you press the dial, the cursor will zoom in on the value on the right.

To move back one step towards the top page, press the [EXIT] button.

NOTE

• The convention used in this manual to describe

DTX700 Owner’s Manual

sequences of cursor operations in the Menu area takes the form: [MENU] m [KIT] m [COMMON].

In this condition, you can turn the dial to change the value selected by the cursor.

When you press the dial again, the cursor will zoom out to select the entire row.

+ 44 hidden pages