Yaesu FTM-400XDE Information For Customers Operating

Information for Customers Operating VHF/UHF Transceivers in the UK

Thank you very much for purchasing the YAESU transceiver.

The transceivers listed in this notice are congured at the factory with the ARS (Automatic Repeater Shift) Frequency
Range, and the Repeater shifts, as shown in the below chart “ARS Conguration B2”.

When any of the listed transceivers is operated in a location where the frequency range and repeater shifts in use are
as shown in the chart “ARS Conguration C2”; follow the respective procedure to change the Automatic Repeater
Shift conguration, before using the transceiver for the rst time.

ARS Conguration “B2”

Factory Default Setting

ARS Frequency Range: 438.20 MHz - less than 439.45 MHz (- shift

)

Repeater Shifts: 7.6 MHz

FTM-400XDE

1. Turn the transceiver OFF.

2. Connect the supplied microphone MH-48A6JA to the
transceiver.

3. Press and hold the [F(MW)] and [GM] keys while turn­ing the transceiver ON.

4. Press the [Power] key briey, then “LOCK” will appear
on the display for one sec.

5. Press [8] à [3] à [7] à [8] à [3] à [7] keys on the
MH-48A6JA microphone.

6. Press the [Power] key briey, then “UNLOCK” will ap­pear on the display for one sec.

7. Press and hold the [DISP(SETUP)] key.

8. Touch the [RESET/CLONE] on the display.

SETUP MENU

DISPLAY

SIGNALING

APRS OPTION

BAC K

BAC K

TX/RX

SCAN

CONFIGW RES

SD CARD

RESET/
CLONE

9. The ARS Configuration name “B2” will appear in the

top right of the display.

RESET/CLONE

FACTORY RESET



PRESE T





RECALL P RESET

MEM CH RESET



BAC K

BAC K

MEMORY

DATA

CALLSIGN

VERSION
MAIN :x.xxx 0EXP B2
PANEL:x.xx

〉

〉

〉

〉

ARS Conguration “C2”

Selectable Setting

ARS Frequency Range: 433.00 MHz - less than 433.40 MHz (+ shift

434.60 MHz - less than 435.00 MHz (- shift

)

Repeater Shifts: 1.6 MHz

FTM-100DE

1. Turn the transceiver OFF.

2. Connect the supplied microphone MH-48A6JA to the
transceiver.

3. Press and hold the [A/B(DW)] and [GM] keys while
turning the transceiver ON.

4. Press the [Power] key briey, then “LOCK” will appear
on the display for one sec.

5. Press [8] à [3] à [7] à [8] à [3] à [7] keys on the
MH-48A6JA microphone.

6. Press the [Power] key briey, then “UNLOCK” will ap­pear on the display for one sec.

7. Press and hold the [DISP(SETUP)] key.

8. Rotate the DIAL to select [13 RST/CLONE], then
press the [DISP(SETUP)] key.

9. Rotate the DIAL to select [8 SOFTWARE VERSION],
then press the [DISP(SETUP)] key.

10. The ARS Conguration name “Region “EXP” Type “B2”
will appear in the bottom on the display.

)

10. Press [F(MW)] key, then the message <Confirming

FROM “B2” TO “C2”> will appear on the display.

11. Touch [OK?]. The radio will re-start automatically.

Setting of the ARS feature to “Configuration C2” is

successfully completed.

VERSION

Confirming

MAIN :x.xxx 0EXP B2
PANEL:x.xx

〉

〉

〉

Cance 

〉

RESET/CLONE

FACTORY RESET



PRESE T



FROM “B2” TO “C2”



RECALL P RESET

O K ?

MEM CH RESET



BAC K

BAC K

To restore the ARS feature setting to the factory default
(B2)

, perform the same procedures above.

11. Press [BAND(MHz)] key, then the message <FROM

“B2” TO “C2”> appears on the display.

12. Rotate the DIAL to select [OK?], and then press the

[

DISP(SETUP

)] key

. The radio will re-start automati-

cally. Setting of the ARS feature to “Conguration C2”

is successfully completed.

To restore the ARS feature setting to the factory default
(B2)

, perform the same procedures above.

FT2DE

FT-65E

1. Turn the transceiver ON.

2. Press and hold in the [DISP] key, then touch the [DIS-

PLAY].

3. Rotate the DIAL knob to select “8OPENING MES­SAGE” and then press the [DISP] key.

4. Rotate the DIAL knob to select “MESSAGE” and then

press the [DISP] key.

5. Enter “AH060M”.

1) Touch the [abc] four times to select “A”, then touch

[Æ]

the

2) Touch the [ghi] ve times to select “H”, then touch

the

3) Touch the [123] key to display the numeric keypad

input screen.

4) Touch the [0] à [6] à [0] à

5) Touch the [ABC] to display the alphabet input

screen.

6) Touch the [mno] four times to select “M”.

6. Press the [PTT] switch, the screen that was shown

when the transceiver was turned ON will reappear on

the display.

7. Turn the transceiver OFF.

8. Press and hold the [X] and [GM] keys while turning the
transceiver ON.

9. <TYPE : B2> appears in the display.

10. Rotate the DIAL knob to select <C2> and touch the

[

WRITE] key. The radio will re-start automatically.

Setting of the ARS feature to “Configuration C2” is

successfully completed.

[Æ]

.

.

[Æ]

.

1. Turn the transceiver OFF.

2.

Press and hold the MONI/T.CALL key and the PTT

switch simultaneously, while turning the transceiver ON.

3. When the LCD backlight
comes on, release the

MONI/T.CALL key and
PTT switch.

4. Press the [0] à [2] à [2] keys.

The radio will re-start automatically. Setting of the ARS
feature to “Conguration C2” is successfully completed.

To restore the ARS feature setting to the factory default
(B2)

, perform the same procedures above.

FT-70DE

1. Turn the transceiver ON.

2. Press and hold in the [F] key.

3. Rotate the DIAL knob to select “36 OPN.MSG” and

then press the [F] key.

4. Rotate the DIAL knob to select “MSG” and then press

the [V/M] key.

5. Enter “AH051M”.

1) Press the

2) Press the

3) Press the [0] to select “0”.

4) Press the

5) Press the

6) Press the

6. Press the [PTT] switch, the screen that was shown

when the transceiver was turned ON will reappear on

the display.

7. Turn the transceiver OFF.

8. Press and hold the [HM/RV] and [GM] keys while turn­ing the transceiver ON.

9. <TYP.B2> appears in the display.

10. Rotate the DIAL knob to select <TYP.C2> and touch

the [F] key. The radio will re-start automatically. Setting
of the ARS feature to “Conguration C2” is successful­ly completed.

[2]

to select “A”.

[4]

two times to select “H”.

[5]

four times to select “5”.

[1]

to select “1”.

[6]

to select “M”.

To restore the ARS feature setting to the factory default
(B2)

To restore the ARS feature setting to the factory default
(B2)

, perform the same procedures above.

, perform the same procedures above.

Caution:

NOTE: By changing the ARS designated bands and repeater shifts according to the procedures above, all saved data,

such as Menu and Memory settings, will be deleted. If you need to change the ARS feature setting after using
the radio, make sure to back up your registered data or make a written note, before applying the setting change.

NOTE: The ARS feature setting is NOT changed, even when executing the “Factory Reset” to restore the transceiver

to the factory defaults, as described in the Operating Manuals (FTM-400XDE: Page 61) (FTM-100DE: Page 49)
(FT2DE: Page 51) (FT-65E: Page 24) (FT-70DE: Page 34).