CAT
(
COMPUTER AIDED TRANSCEIVER
)
OPERATION
FTDX5000
CAT O
R
EFERENCE
PERATION
B
S
OOK
ERIES
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
)
OPERATION
OVERVIEW
The CAT (Computer Aided Transceiver) System in the
FTDX5000 series provides control of frequency, VFO,
memory, and other settings such as dual-channel memories and diversity reception using an external personal
computer. This allows multiple control operations to be
fully automated as single mouse clicks or keystroke operations on the computer keyboard.
The FTDX5000 series has a built-in level converter, allowing direct connection from the rear-panel CAT jack to
the serial port of your computer without the need of any
external boxes. You will need a serial cable for connection to the RS-232C (serial or COM port) connector on
your computer. Purchase a standard serial cable (not the
so-called “null modem” type), ensuring it has the correct
gender and number of pins (some serial COM port connectors use a 9-pin rather than 25-pin configuration). If
your computer uses a custom connector, you may have to
construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data
connection.
Vertex Standard does not produce CAT System operating
software due to the wide variety of personal computers
and operating systems in use today. However, the information provided in this chapter explains the serial data
structure and opcodes used by the CAT system. This information, along with the short programming examples,
is intended to help you start writing programs on your
own. As you become more familiar with CAT operation,
you can customize programs later on for your operating
needs and discover the true operating potential of this system.
PIN NO.
PIN NAME
N/A
SERIAL OUT
SERIAL IN
N/A
GND
N/A
RTS
CTS
N/A
CAT JACK
I/O
--Outputs the Serial Data from the
Output
transceiver to the computer.
Input
Inputs the Serial Data from the
computer to the transceiver.
---
---
--When the computer is not ready
Input
to receive data, this port goes to
“L” for inhibit the transmit data
from the transceiver.
Output
When the transceiver is not ready
to receive data, this port goes to
“L” for inhibit the transmit data
from the computer.
---
FUNCTION
---
---
Signal Ground
---
---
Page 1
COM
T
A
C
RS-232C "Straght" Cable
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND
)
OPERATION
A computer control command is composed of an alphabetical command, various parameters, and the terminator
that signals the end of the control command.
Example: Set the main band (VFO-A) frequency to
14.250000 MHz.
FA 14250000 ;
Command Parameter Terminator
There is three for the FT
low:
Set command: Set a particular condition
Read command: Reads an answer
Answer command: Transmits a condition
For example, note the following in the case of the F A command (Set the main band (VFO-A) frequency):
T o set the main band (VFO-A) frequency to 14.250000
MHz, the following command is sent from the computer to the transceiver:
“FA14250000;” (Set command)
To read the main band (VFO-A) frequency, the fol-
lowing command is sent from the computer to the transceiver:
“FA;” (Read command)
When the Read command above has been sent, the
following command is returned to the computer:
“FA14250000;” (Answer command)
DX5000 Command as shown be-
(to the FTDX5000)
(from the FTDX5000)
(from the FTDX5000)
Alphabetical Commands
A command consists of 2 alphabetical characters.
Parameters
Parameters are used to specify information necessary to
implement the desired command.
The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the “Control Command List” and the “Control Command Tables” to configure the appropriate parameters.
When configuring parameters, be careful not to make the
following mistakes.
For example, when correct parameter is “IS0+1000” (IF
SHIFT):
IS01000;
Not enough parameters specified (No direction (+)
given for the IF shift)
IS0+100;
Not enough digits (Only three frequency digits
given)
IS0_+_1000;
Unnecessary characters between parameters
IS0+10000;
Too many digits (Five frequency digits given)
Note: If a particular parameter is not applicable to the
FT
DX5000, the parameter digits should be filled using
any character except the ASCII control codes (00 to 1Fh)
and the terminator (;).
Terminator
To signal the end of a command, it is necessary to use a
semicolon (;). The digit where this special character must
appear differs depending on the command used.
You may use either lower or upper case characters. The
commands available for this transceiver are listed in the
“PC Control Command Tables” on the following pages.
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 2
CAT
C
OMMAND
VFO-A T O VFO-B
AB
ANTENNA TUNER CONTROL
AC
AF GAIN
AG
AUTO INFORMA TION
AI
VFO-A TO MEMORY CHANNEL
AM
ANTENNA NUMBER
AN
VFO-B TO VFO-A
BA
AUTO NOTCH
BC
BAND DOWN
BD
BREAK-IN
BI
MANUAL NOTCH
BP
BAND SELECT
BS
BAND UP
BU
BUSY
BY
CLASS-A
CA
CHANNEL UP/DOWN
CH
CTCSS NUMBER
CN
CONTOUR
CO
CW SPOT
CS
CTCSS
CT
DIMMER
DA
DOWN
DN
DISPLAY
DP
DIMMER SWITCH
DS
ENCORDER DOWN
ED
ENCORDER UP
EU
MENU
EX
FREQUENCY VFO-A
FA
FREQUENCY VFO-B
FB
FUNCTION RX
FR
FAST STEP
FS
FUNCTION TX
FT
AGC FUNCTION
GT
IDENTIFICATION
ID
INFORMATION
IF
IF-SHIFT
IS
KEYER MEMORY
KM
KEY PITCH
KP
KEYER
KR
KEY SPEED
KS
CW KEYING
KY
LOCK
LK
LOAD MESSAGE
LM
MEMORY CHANNEL TO VFO-A
MA
MEMORY CHANNEL
MC
MODE
MD
MIC GAIN
MG
MODE KEY
MK
MONITOR LEVEL
ML
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND LIST
FUNCTION SET READ AI
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
ANS.
X
X
O
O
O
O
O
O
X
X
O
O
X
X
O
O
X
X
O
O
O
O
X
X
X
X
O
O
O
O
X
X
O
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
X
X
O
O
O
O
O
O
X
X
O
O
C
OMMAND
MEMORY READ
MR
X
METER SW
MS
O
MEMORY WRITE
MW
O
MOX SET
MX
X
NARROW
NA
X
NOISE BLANKER
NB
O
NOISE BLANKER LEVEL
NL
X
NOISE REDUCTION
NR
O
OPPOSITE BAND INFORMATION
OI
X
OFFSET (REPEATER SHIFT)
OS
O
PRE-AMP (IPO)
PA
O
PLAY BACK
PB
X
POWER CONTROL
PC
X
SPEECH PROCESSOR LEVEL
PL
O
SPEECH PROCESSOR
PR
O
POWER SWITH
PS
X
QMB STORE
QI
O
QMB RECALL
QR
O
QUICK SPLIT
QS
O
RF ATTENUA T OR
RA
O
CLAR CLEAR
RC
X
CLAR DOWN
RD
X
ROOFING FILTER
RF
O
RF GAIN
RG
O
RADIO INFORMA TION
RI
X
NOISE REDUCTION LEVEL
RL
X
READ METER
RM
O
ROTATOR
RO
O
RADIO STATUS
RS
O
CLAR
RT
O
CLAR UP
RU
O
SCAN
SC
O
SEMI BREAK-IN DELAY TIME
SD
O
SUB-DIAL FUNCTION
SF
X
WIDTH
SH
O
S METER
SM
O
SQUELCH LEVEL
SQ
X
SWAP VFO
SV
O
TXW
TS
O
TX SET
TX
O
UNLOCK
UL
X
UP
UP
O
VOX DELAY TIME
VD
X
VRF FIL TER
VF
X
VOX GAIN
VG
X
[
V/M] KEY FUNCTION
VM
O
VFO SELECT
VS
O
VOX
VX
X
TX CLAR
XT
O
)
OPERATION
FUNCTION SET READ AI
O
X
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
X
O
X
O
O
O
X
O
X
O
O
O
O
O
O
X
O
O
O
X
O
O
O
X
O
O
X
O
O
O
O
O
O
O
O
O
O
X
O
O
X
O
O
O
O
O
O
X
X
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
ANS.
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
X
O
X
X
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
X
O
O
O
X
O
O
O
X
O
O
O
X
O
X
O
O
O
O
O
X
O
O
X
O
O
O
X
X
X
X
O
X
X
O
O
O
O
O
X
O
O
X
O
O
O
O
O
O
X
O
O
O
X
O
O
O
X
O
O
O
Page 3
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
ABAB
AB VFO-A TO VFO-B
ABAB
Set 12345678910
Read 12345678910
Answer 12345678910
AA
CC
A
C ANTENNA TUNER CONTROL
AA
CC
Set 12345678910
Read 12345678910
Answer 12345678910
AA
GG
A
G AF GAIN
AA
GG
Set 12345678910
Read 12345678910
Answer 12345678910
AIAI
AI AUTO INFORMA TION
AIAI
Set 12345678910
Read 12345678910
Answer 12345678910
AMAM
AM VFO-A TO MEMOR Y CHANNEL
AMAM
Set 12345678910
Read 12345678910
AB ;
ACP1 P2 P3 ;
AC ;
ACP1 P2 P3 ;
AGP1 P2 P2 P2 ;
AGP1 ;
AGP1 P2 P2 P2 ;
AIP1 ;
AI ;
AIP1 ;
AM ;
)
OPERATION
P1 0: Fixed P3 0:Tuner “OFF”
P2 0: Fixed 1:Tuner “ON”
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 000 - 255
P1 0: Auto Information “OFF”
1:Auto Information “ON”
This parameter is set to “0” (OFF) automatically when the transceiver is turned “OFF.”
2:Tuning Start
Answer 12345678910
ANAN
AN ANTENNA NUMBER
ANAN
Set 12345678910
Read 12345678910
Answer 12345678910
BB
AA
B
A VFO-B TO VFO-A
BB
AA
Set 12345678910
Read 12345678910
Answer 12345678910
BCBC
BC AUTO NOTCH
BCBC
Set 12345678910
Read 12345678910
Answer 12345678910
BDBD
BD BAND DOWN
BDBD
Set 12345678910
Read 12345678910
ANP1 P2 ;
ANP1 ;
ANP1 P3 P4 ;
BA;
BCP1 P2 ;
BCP1 ;
BCP1 P2 ;
BDP1 ;
P1 0: Main (VFO-A) Band
1: Sub (VFO-B) Band
P1 0: Main (VFO-A) Band Receiver
1: Sub (VFO-B) Band Receiver
P2 0: Auto Notch “OFF”
1:Auto Notch “ON”
P1 0: Main (VFO-A) Band
1:Sub (VFO-B) Band
P2 1: ANT “1”
2: ANT “2”
3: ANT “3”
4: ANT “4”
5: ANT “RX”
P3 1: ANT “1”
2: ANT “2”
3: ANT “3”
4: ANT “4”
P4 0: ANT “RX” “OFF”
1: ANT “RX” “ON”
Answer 12345678910
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 4
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
BIBI
BI BREAK-IN
BIBI
Set 12345678910
Read 12345678910
Answer 12345678910
BPBP
BP MANUAL NOTCH
BPBP
Set 12345678910
Read 12345678910
Answer 12345678910
BSBS
BS BAND SELECT
BSBS
Set 12345678910
Read 12345678910
Answer 12345678910
BB
UU
B
U BAND UP
BB
UU
Set 12345678910
Read 12345678910
BIP1 ;
BI ;
BIP1 ;
BPP1 P2 P3 P3 P3 ;
BPP1 P2 ;
BPP1 P2 P3 P3 P3 ;
BSP1 P1 ;
BUP1 ;
)
OPERATION
P1 0: Break-in “OFF”
1:Break-in “ON”
P1 0: Main (VFO-A) Band Receiver
1: Sub (VFO-B) Band Receiver
P2 0: Manual NOTCH “ON/OFF”
1: Manual NOTCH LEVEL
P1 00: 1.8 MHz 06: 18 MHz
01: 3.5 MHz 07: 21 MHz
02: - 08: 24.5 MHz
03: 7 MHz 09: 28 MHz
04: 10 MHz 10: 50 MHz
05: 14 MHz 11: GEN
P1 0: Main (VFO-A) Band
1:Sub (VFO-B) Band
P3 When P2=0
000: OFF
001: ON
When P2=1
001 - 400 (NOTCH Frequency : x 10 Hz )
Answer 12345678910
BYBY
BY BUSY
BYBY
Set 12345678910
Read 12345678910
BY ;
Answer 12345678910
BYP1 P2 ;
CACA
CA CLASS-A
CACA
Set 12345678910
CAP1 P2 P2 P2 ;
Read 12345678910
CAP1 ;
Answer 12345678910
CAP1 P2 P2 P2 ;
CHCH
CH CHANNEL UP/DOWN
CHCH
Set 12345678910
CHP1 ;
Read 12345678910
Answer 12345678910
CNCN
CN CTCSS TONE FREQUENCY
CNCN
Set 12345678910
CNP1 P2 P2 ;
Read 12345678910
CNP1 ;
Answer 12345678910
CNP1 P2 P2 ;
P1 0: Main (VFO-A) Band BUSY “OFF”
1:Main (VFO-A) Band BUSY “ON”
P2 0: Sub (VFO-B) Band BUSY “OFF”
1:Sub (VFO-B) Band BUSY “ON”
P1 0:CLASS-A ON/OFF
1: BIAS LEVEL
P2 When P1=0
000: OFF
001: ON
When P1=1
001 - 100
P1 0: Memory Channel “UP”
1:Memory Channel “DOWN”
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 0 - 49: Tone Frequency Number
Page 5
00
67.0 Hz
01
69.3 Hz
02
71.9 Hz
03
74.4 Hz
04
77.0 Hz
05
79.7 Hz
06
82.5 Hz
07
85.4 Hz
08
88.5 Hz
09
10
11
12
13
14
15
16
17
91.5 Hz
94.8 Hz
97.4 Hz
100.0 Hz
103.5 Hz
107.2 Hz
110.9 Hz
114.8 Hz
118.8 Hz
18
19
20
21
22
23
24
25
26
123.0 Hz
127.3 Hz
131.8 Hz
136.5 Hz
141.3 Hz
146.2 Hz
151.4 Hz
156.7 Hz
159.8 Hz
27
28
29
30
31
32
33
34
35
162.2 Hz
165.5 Hz
167.9 Hz
171.3 Hz
173.8 Hz
177.3 Hz
179.9 Hz
183.5 Hz
186.2 Hz
36
37
38
39
40
41
42
43
44
189.9 Hz
192.8 Hz
196.6 Hz
199.5 Hz
203.5 Hz
206.5 Hz
210.7 Hz
218.1 Hz
225.7 Hz
45
46
47
48
49
---
---
---
---
229.1 Hz
233.6 Hz
241.8 Hz
250.3 Hz
254.1 Hz
---
---
---
---
FTDX5000 SERIES CAT OPERATION REFERENCE
CTCSS TONE CHART
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
COCO
CO CONTOUR
COCO
Set 12345678910
Read 12345678910
Answer 12345678910
CSCS
CS CW SPOT
CSCS
Set 12345678910
Read 12345678910
Answer 12345678910
CTCT
CT CTCSS
CTCT
Set 12345678910
Read 12345678910
Answer 12345678910
DD
AA
D
A DIMMER
DD
AA
Set 12345678910
Read 12345678910
Answer 12345678910
Set 11 12 13 14 15 16 17 18 19 20
Read 11 12 13 14 15 16 17 18 19 20
COP1 P2 P3 P3 ;
COP1 P2 ;
COP1 P2 P3 P3 ;
CSP1 ;
CS ;
CSP1 ;
CTP1 P2 ;
CTP1 ;
CTP1 P2 ;
DAP1 P1 P2 P2 P3 P3 P4 P4
DA;
DAP1 P1 P2 P2 P3 P3 P4 P4
;
P1 0: Main (VFO-A) Band Receiver
1: Sub (VFO-B) Band Receiver
P2 0: CONTOUR/APF “ON/OFF”
1: CONTOUR FREQUENCY
P1 0:OFF
1:ON
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 0: CTCSS “OFF”
1:CTCSS ENC/DEC “ON”
2:CTCSS ENC “ON”
P1 00 - 15: VFD Backlight Brightness Level
P2 00 - 15: Meter Brightness Level
P3 00 - 15: OLE Brightness Level
P4 00 - 15: ELCD (SM-5000) Brightness Level
P3 When P2=0,
When P2=1,
)
OPERATION
000: CONTOUR/APF “OFF”
001: CONTOUR “ON”
002: APF “ON”
01 - 40 (CONTOUR FREQUENCY)
100 ~ 4000 Hz
Answer 11 12 13 14 15 16 17 18 19 20
;
DNDN
DN MIC DWN
DNDN
Set 12345678910
Read 12345678910
Answer 12345678910
DPDP
DP DISPLAY
DPDP
Set 12345678910
Read 12345678910
Answer 12345678910
DSDS
DS DIMMER SWITCH
DSDS
Set 12345678910
Read 12345678910
Answer 12345678910
EDED
ED ENCORDER DOWN
EDED
Set 12345678910
Read 12345678910
Answer 12345678910
DN ;
DPP1 ;
DP ;
DPP1 ;
DSP1 ;
DS ;
DSP1 ;
EDP1 P2 P2 ;
P1 0: World Clock Display
1:Band Scope Display
2:AF Oscilloscope/Spectrum Analyzer Display
3:Log Book Display
4:Temperature/SWR Display
5:Rotator Display
6:Memory Channel List Display
P1 0: DIMMER “OFF”
1:DIMMER “ON”
P1 0: MAIN ENCORDER
1:SUB ENCORDER
2:MAIN Select
3:SUB Select
P2 01-99: Steps
: This command does not acti-
vates when the optional Data
Managemnt Unit is not attached.
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 6
CAT
(
COMPUTER AIDED TRANSCEIVER
)
OPERATION
CONTROL COMMAND TABLES
EUEU
EU ENCORDER UP
EUEU
Set 12345678910
EUP1 P2 P2 ;
Read 12345678910
Answer 12345678910
EXEX
EX MENU
EXEX
Set 12345678nn
EXP1 P1 P1 P2 P2 ~ P2 ;
Read 12345678910
EXP1 P1 P1 ;
Answer 12345678nn
EXP1 P1 P1 P2 P2 ~ P2 ;
P1 FUNCTION P2
001 MAIN-FAST-DELAY 0020~4000 (20msec/step) 4
002 MAIN-FAST-HOLD 0000~2000 (20msec/step) 4
003 MAIN-MID-DELAY 0020~4000 (20msec/step) 4
004 MAIN-MID-HOLD 0000~2000 (20msec/step) 4
005 MAIN-SLOW-DELAY 0020~4000 (20msec/step) 4
006 MAIN-SLOW-HOLD 0000~2000 (20msec/step) 4
007 TFT COLOR 0: COOL BLUE, 1: CONTRAST BLUE, 2: FLASH WHITE, 3: CONTRAST UMBER, 4: UMBER 1
008 DIMMER-METER 00~15 2
009 DIMMER-VFD 00~15 2
010 DIMMER-OLE 00~15 2
011 DIMMER-E.LCD 00~15 2
012 BAR DISPLAY SELECT 0: CLAR, 1: CW TUNE 1
013 SUB MTR PEAK HOLD 0: OFF, 1: 0.5, 2: 1.0, 3: 2.0 (sec) 1
014 ROTATOR START UP 0: 0°, 1: 90°, 2: 180°, 3: 270° 1
015 ROTATOR OFFSET ADJ -30~0 (P2 = 30~00) (2°step) 2
016 QMB MARKER 0: DISABLE, 1: ENABLE 1
017 LEVEL INDICATOR 0000000000000 ~ 1111111111111 (see Page 9) 13
018 INDICATOR 0: VFD, 1: OEL 1
019 SELECT 0: PTN1, 1: PTN2 1
020 RX OUT LEVEL 000~100 3
021 TX OUT LEVEL 000~100 3
022 BEACON TIME OFF/001~255sec (0: OFF) 3
023 NUMBER STYLE 0: 1290, 1: AUNO, 2: AUNT, 3: A2NO, 4: A2NT, 5: 12NO, 6: 12NT 1
024 CONTEST NUMBER 0000~9999 4
025 CW MEMORY 1 0: TEXT, 1: MESSAGE 1
026 CW MEMORY 2 0: TEXT, 1: MESSAGE 1
027 CW MEMORY 3 0: TEXT, 1: MESSAGE 1
028 CW MEMORY 4 0: TEXT, 1: MESSAGE 1
029 CW MEMORY 5 0: TEXT, 1: MESSAGE 1
030 ANT SELECT 0: BAND, 1: STACK 1
031 BEEP LEVEL 000~100 3
032 CAT RATE 0: 4800, 1: 9600, 2: 19200, 3: 38400 (bps) 1
033 CAT TIME OUT TIMER 0: 10, 1: 100, 2: 1000, 3: 3000 (msec) 1
034 CAT RTS 0: DISABLE, 1: ENABLE 1
035 CAT DATA INDICATOR 0: DISABLE, 1: ENABLE 1
036 MEM GROUP 0: DISABLE, 1: ENABLE 1
037 QUICK SPLIT FREQ -20 ~ +20 kHz (P2 = -20 ~ +00 ~ +20) 3
038 TRACKING 0: OFF, 1: BAND, 2: FREQ 1
039 TIME OUT TIMER OFF/01~30min 2
040 TRV OFFSET (14MHz) 30: 30, 31: 31, 32: 32 ~ 44: 44, 45: 45, 46: 46 (MHz) 2
041 TRV OFFSET (28MHz) 30: 30, 31: 31, 32: 32 ~ 44: 44, 45: 45, 46: 46 (MHz) 2
042 TRV OFFSET (50MHz) 30: 30, 31: 31, 32: 32 ~ 44: 44, 45: 45, 46: 46 (MHz) 2
043 uTUNE DIAL STEP 0: DIAL STEP-2, 1: DIAL STEP-1, 2: OFF 1
044 MIC SCAN 0: DISABLE, 1: ENABLE 1
045 MIC SCAN RESUME 0: PAUSE, 1: TIME 1
046 FREQ ADJ -25~0~+25 (P2 = -25 ~ +00 ~ +25) 3
047 AM LCUT FREQ 00: OFF, 01: 100Hz, ~, 19: 1000Hz (50Hz/step) 2
048 AM LCUT SLOPE 0: 6dB/oct, 1: 18dB/oct 1
049 AM HCUT FREQ 00: OFF, 01: 700Hz, ~, 67: 4000Hz (50Hz/step) 2
050 AM HCUT SLOPE 0: 6dB/oct, 1: 18dB/oct 1
051 AM MIC GAIN MCVR/FIX(0~100) (P2 = 1000: MCVR, 0000~0100: FIX(0~100)) 4
052 AM MIC SEL 0: FRONT, 1: DATA, 2: PC 1
053 CW LCUT FREQ 00: OFF, 01: 100Hz, ~, 19: 1000Hz (50Hz/step) 2
054 CW LCUT SLOPE 0: 6dB/oct, 1: 18dB/oct 1
055 CW HCUT FREQ 00: OFF, 01: 700Hz, ~, 67: 4000Hz (50Hz/step) 2
056 CW HCUT SLOPE 0: 6dB/oct, 1: 18dB/oct 1
057 F-KEYER TYPE 0: OFF, 1: BUG, 2: ELEKEY, 3: ACS 1
058 F-CW KEYER 0: NOR, 1: REV 1
059 R-KEYER TYPE 0: OFF, 1: BUG, 2: ELEKEY, 3: ACS 1
060 R-CW KEYER 0: NOR, 1: REV 1
061 CW AUTO MODE 0: OFF, 1: 50M, 2: ON 1
062 CW BFO 0: USB, 1: LSB, 2: AUTO 1
063 CW BK-IN 0: SEMI, 1: FULL 1
064 CW WAVE SHAPE 0: 1, 1: 2, 2: 4, 3: 6 (msec) 1
065 CW WEIGHT 2.5~3.0~4.5 (P2 = 25~45) 2
066 CW FREQ DISPLAY 0: DIRECT FREQ, 1: PITCH OFFSET 1
067 PC KEYING 0: DISABLE, 1: ENABLE 1
P1 0: MAIN ENCORDER
1:SUB ENCORDER
2:MAIN Select
3:SUB Select
P2 01-99: Steps
P1 : 001-176 (MENU Number)
**
P2 : Parameter
See Table 1 - Table 3
**
TABLE 1
BYTE
Page 7
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
)
OPERATION
CONTROL COMMAND TABLES
TABLE 2
P1 FUNCTION P2
068 QSK 0: 15, 1: 20, 2: 25, 3: 30 (msec) 1
069 DATA IN SELECT 0: DATA, 1: PC 1
070 DAT A TX GAIN 000~100 3
071 DATA OUT 0: VFO-A, 1: VFO-B 1
072 DATA OUT LEVEL 000~100 3
073 DATA VOX DELAY 0030~0300~3000msec (10msec/step) 4
074 DATA VOX GAIN 000~100 3
075 FM LCUT FREQ 00: OFF, 01: 100Hz, ~, 19: 1000 Hz (50Hz/step) 2
076 FM LCUT SLOPE 0: 6, 1: 18 (dB/oct) 1
077 FM HCUT FREQ 00: OFF, 01: 700, ~ , 67: 4000 Hz (50Hz/step) 2
078 FM HCUT SLOPE 0: 6 , 1: 18 (dB/oct) 1
079 FM MIC GAIN MCVR/FIX(0~100) (P2 = 1000: MCVR, 0000~0100: FIX(0~100)) 4
080 FM MIC SEL 0: FRONT, 1: DATA, 2: PC 1
081 RPT SHIFT(28MHz) 0000 ~0100 ~ 1000 kHz (10Hz/step) 4
082 RPT SHIFT(50MHz) 0000 ~0100 ~ 1000 ~ 4000 kHz (10Hz/step) 4
083 PKT LCUT FREQ 00: OFF, 01: 100Hz, ~ , 19: 1000 Hz (50Hz/step) 2
084 PKT LCUT SLOPE 0: 6, 1: 18 (dB/oct) 1
085 PKT HCUT FREQ 00: OFF, 01: 700, ~ , 67: 4000 Hz (50Hz/step) 2
086 PKT HCUT SLOPE 0: 6, 1: 18 (dB/oct) 1
087 PKT DISP (SSB) -3000 ~ 0 ~ +3000 Hz (10Hz/step) (P2 = -3000 ~ +0000 ~ +3000) 5
088 PKT SHIFT (SSB) -3000 ~ 0 ~ +3000 Hz (10Hz/step) (P2 = -3000 ~ +0000 ~ +3000) 5
089 RTTY LCUT FREQ 00: OFF, 01: 100, ~ , 19: 1000 Hz (50Hz/step) 2
090 RTTY LCUT SLOPE 0: 6, 1: 18 (dB/oct) 1
091 RTTY HCUT FREQ 00: OFF, 01: 700, ~ , 67: 4000 Hz (50Hz/step) 2
092 RTTY HCUT SLOPE 0: 6, 1: 18 (dB/oct) 1
093 POLARITY-R 0: NOR, 1: REV 1
094 POLARITY-T 0: NOR, 1: REV 1
095 RTTY OUT 0: VFO-A, 1: VFO-B 1
096 RTTY OUT LEVEL 000 ~100 3
097 RTTY SHIFT 0: 170, 1: 200, 2: 425, 3: 850 (Hz) 1
098 RTTY TONE 0: 1275, 1: 2125 (Hz) 1
099 SSB LCUT FREQ 00: OFF, 01: 100 ~ 19: 1000Hz (50Hz/step) 2
100 SSB LCUT SLOPE 0: 6, 1: 18 (dB/oct) 1
101 SSB HCUT FREQ 00: OFF, 01: 700 ~ 67: 4000 Hz (50Hz/step) 2
102 SSB HCUT SLOPE 0: 6 1: 18 (dB/oct) 1
103 SSB MIC SELECT 0: FRONT, 1: DATA, 2: PC 1
104 SSB-TX-BPF 0: 50-3000, 1: 100-2900, 2: 200-2800, 3: 300-2700, 4: 400-2600(Hz), 5: 3000WB 1
105 LSB RX-CARRIER -200Hz~0~+200 Hz (10Hz/step) (P2 = -200 ~ +000 ~ +200) 4
106 USB RX-CARRIER -200Hz~0~+200 Hz (10Hz/step) (P2 = -200 ~ +000 ~ +200) 4
107 AGC-SLOPE 0: NORMAL, 1: SLOPE 1
108 HEADPHONE MIX 0: SEPARATE, 1: COMBINE-1, 2: COMBINE-2 1
109 IF OUT 0: ENABLE, 1: DISABLE 1
110 MAIN NB LEVEL 000 ~100 3
111 MAIN NB WIDTH 000 ~100 3
112 MAIN-CONTOUR-LEVEL -40~0~20 (P2 = -40 ~ +00 ~ +20) 3
113 MAIN-CONTOUR-WIDTH 01 ~11 2
114 IF-NOTCH-WIDTH 0: NARROW, 1: WIDE 1
115 MAIN-CW SHAPE 0: SOFT, 1: SHARP 1
116 MAIN-CW SLOPE 0: STEEP, 1: MEDIUM, 2: GENTLE 1
117 MAIN-PSK SHAPE 0: SOFT, 1: SHARP 1
118 MAIN-PSK SLOPE 0: STEEP, 1: MEDIUM, 2: GENTLE 1
119 MAIN-RTY SHAPE 0: SOFT, 1: SHARP 1
120 MAIN-RTY SLOPE 0: STEEP, 1: MEDIUM, 2: GENTLE 1
121 MAIN-SSB SHAPE 0: SOFT, 1: SHARP 1
122 MAIN-SSB SLOPE 0: STEEP, 1: MEDIUM, 2: GENTLE 1
123 SUB-CW SHAPE 0: SOFT, 1: SHARP 1
124 SUB-CW SLOPE 0: STEEP, 1: MEDIUM, 2: GENTLE 1
125 SUB-PSK SHAPE 0: SOFT, 1: SHARP 1
126 SUB-PSK SLOPE 0: STEEP, 1: MEDIUM, 2: GENTLE 1
127 SUB-RTY SHAPE 0: SOFT, 1: SHARP 1
128 SUB-RTY SLOPE 0: STEEP, 1: MEDIUM, 2: GENTLE 1
129 SUB-SSB SHAPE 0: SOFT, 1: SHARP 1
130 SUB-SSB SLOPE 0: STEEP, 1: MEDIUM, 2: GENTLE 1
131 FIX 1.8MHz 1.800MHz ~ 1.999MHz 1kHz /step (P2 = 01800 ~ 01999) 5
132 FIX 3.5MHz 3.500MHz ~ 3.999MHz 1kHz /step (P2 = 03500 ~ 03999) 5
133 FIX 5.0MHz 5.250MHz ~ 5.499MHz 1kHz /step (P2 = 05250 ~ 05499) 5
134 FIX 7.0MHz 7.000MHz ~ 7.299MHz 1kHz /step (P2 = 07000 ~ 07299) 5
135 FIX 10MHz 10.100MHz ~ 10.149MHz 1kHz /step (P2 = 10100 ~ 10149) 5
136 FIX 14MHz 14.000MHz ~ 14.349MHz 1kHz /step (P2 = 14000 ~ 14349) 5
137 FIX 18MHz 18.000MHz ~ 18.199MHz 1kHz /step (P2 = 18000 ~ 18199) 5
138 FIX 21MHz 21.000MHz ~ 21.449MHz 1kHz /step (P2 = 21000 ~ 21449) 5
139 FIX 24MHz 24.800MHz ~ 24.989MHz 1kHz /step (P2 = 24800 ~ 24989) 5
140 FIX 28MHz 28.000MHz ~ 29.699MHz 1kHz /step (P2 = 28000 ~ 29699) 5
141 FIX 50MHz 50.000MHz ~ 53.999MHz 1kHz /step (P2 = 50000 ~ 53999) 5
142 DIAL STEP 0: 1, 1: 5Hz, 2: 10Hz 1
143 DIAL CW FINE 0: DISABLE, 1: ENABLE 1
144 UP/DOWN STEP 0: 1MHz, 1: 100kHz 1
145 AM CH STEP 0: 2.5, 1: 5, 2: 9, 3: 10, 4: 12.5kHz 1
146 FM CH STEP 0: 5, 1: 6.25, 2: 10, 3: 12.5, 4: 20kHz, 5: 25kHz 1
147 AM DIAL LOCK 0: DISABLE, 1: ENABLE 1
148 FM DIAL LOCK 0: DISABLE, 1: ENABLE 1
149 FM DIAL STEP 0: 10, 1: 100Hz 1
150 MY BAND 00000000000000 ~ 11111111111111 (see Page 9) 14
151 PRMTRC EQ1 FREQ 00: OFF, 01: 100, 02: 200, 03: 300, 04: 400, 05: 500, 06: 600, 07: 700 (Hz) 2
152 PRMTRC EQ1 LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) 3
153 PRMTRC EQ1 BWTH 01~10 2
154 PRMTRC EQ2 FREQ 00: OFF, 01: 700, 02: 800, 03: 900, 04: 1000, 05: 1100, 06: 1200, 07: 1300, 08: 1400, 09: 1500 (Hz) 2
155 PRMTRC EQ2 LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) 3
156 PRMTRC EQ2 BWTH 01~10 2
157 PRMTRC EQ3 FREQ 00: OFF,01: 1500, 02: 1600, 03: 1700,04: 1800, 05: 1900, 06: 2000, 07: 2100, 08: 2200, 09: 2300 2
10: 2400, 11: 2500, 12: 2600, 13: 2700, 14: 2800, 15: 2900, 16: 3000, 17: 3100, 18: 3200 (Hz)
BYTE
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 8
CAT
(
COMPUTER AIDED TRANSCEIVER
)
OPERATION
CONTROL COMMAND TABLES
TABLE 3
P1 FUNCTION P2
158 PRMTRC EQ3 LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) 3
159 PRMTRC EQ3 BWTH 01~10 2
160 P-PRMTRC EQ1-FREQ 00: OFF, 01: 100, 02: 200, 03: 300, 04: 400, 05: 500, 06: 600, 07: 700 (Hz) 2
161 P-PRMTRC EQ1-LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) 3
162 P-PRMTRC EQ1-BWTH 01~10 2
163 P-PRMTRC EQ2-FREQ 00: OFF, 01: 700, 02: 800, 03: 900, 04: 1000, 05: 1100, 06: 1200, 07: 1300, 08: 1400, 09: 1500 (Hz) 2
164 P-PRMTRC EQ2-LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) 3
165 P-PRMTRC EQ2-BWTH 01~10 2
166 P-PRMTRC EQ3-FREQ 00: OFF, 01: 1500, 02: 1600, 03: 1700,04: 1800, 05: 1900, 06: 2000, 07: 2100, 08: 2200, 09: 2300 2
167 P-PRMTRC EQ3-LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) 3
168 P-PRMTRC EQ3-BWTH 01~10 2
169 FINAL BIAS A(1~100%) (P2 = 0001~0100: A(1~100%)) 4
170 TX MAX POWER 0: 10(20), 1: 20(50), 2: 50(100), 3: 100(200) (200W type) 1
171 TX PWR CONTROL 0: ALL MODE, 1: CARRIER 1
172 EXT AMP TX-GND 0: DISABLE, 1: ENABLE 1
173 EXT AMP TUNING PWR 0: 10(20), 1: 20(50), 2: 50(100), 3: 100(200) (200W type) 1
174 VOX SELECT 0: MIC, 1: DATA 1
175 ANTI VOX GAIN 000~100 3
176 EMERGENCY FREQ TX 0: DISABLE, 1: ENABLE 1
10: 2400, 11: 2500, 12: 2600, 13: 2700, 14: 2800, 15: 2900, 16: 3000, 17: 3100, 18: 3200 (Hz)
BYTE
Menu Item 017 LEVEL INDICATOR
Command P2 13-Byte Details
1 Byte - - - - - - - - - - - - - - 13-Byte
X X X X X X X X X X X X X
-
-
PROCE
MIC GAIN
RF PWR
VOX DELAY
CW DELAY
-
-
CW SPEED
CW PITCH
Menu Item 150 MY BAND SELECT
Command P2 14-Byte Details
1 Byte - - - - - - - - - - - - - - - - 14-Byte
X X X X X X X X X X X X X X
TRANSVERTER 50M
TRANSVERTER 28M
TRANSVERTER 14M
GENERAL
50 MHz
28 MHz
24.5 MHz
21 MHz
18 MHz
14 MHz
10 MHz
7 MHz
3.5 MHz
1.8 MHz
Page 9
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
FF
AA
F
A FREQUENCY VFO-A
FF
AA
Set 12345678910
FAP1 P1 P1 P1 P1 P1 P1 P1
11 12 13 14 15 16 17 18 19 20
Read 12345678910
Answer 12345678910
FBFB
FB FREQUENCY VFO-B
FBFB
Set 12345678910
Read 12345678910
Answer 12345678910
FRFR
FR FUNCTION RX
FRFR
Set 12345678910
Read 12345678910
Answer 12345678910
FSFS
FS FAST STEP
FSFS
Set 12345678910
Read 12345678910
Answer 12345678910
FTFT
FT FUNCTION TX
FTFT
Set 12345678910
Read 12345678910
Answer 12345678910
GTGT
GT AGC FUNCTION
GTGT
Set 12345678910
Read 12345678910
Answer 12345678910
;
FA;
FAP1 P1 P1 P1 P1 P1 P1 P1
11 12 13 14 15 16 17 18 19 20
;
FBP1 P1 P1 P1 P1 P1 P1 P1
11 12 13 14 15 16 17 18 19 20
;
FB;
FBP1 P1 P1 P1 P1 P1 P1 P1
11 12 13 14 15 16 17 18 19 20
;
FRP1 ;
FR;
FRP1 ;
FSP1 ;
FS;
FSP1 ;
FTP1 ;
FT;
FTP2 ;
GTP1 P2 ;
GTP1 ;
GTP1 P3 ;
)
OPERATION
P1 00030000 - 60000000 (Hz)
P1 00030000 - 60000000 (Hz)
P1 0: Main (VFO-A) Band Receiver: RX, Sub (VFO-B) Band Receiver: “OFF”
1: Main (VFO-A) Band Receiver: Mute, Sub (VFO-B) Band Receiver: “OFF”
2: Main (VFO-A) Band Receiver: RX, Sub (VFO-B) Band Receiver: RX
3: Main (VFO-A) Band Receiver: Mute, Sub (VFO-B) Band Receiver: RX
P1 0: VFO A “OFF” (SET Only)
1:VFO A “ON” (SET Only)
2: VFO B “OFF” (SET Only)
3:VFO B “ON” (SET Only)
P1 0: TX Band = Main (VFO-A) Band Sub (VFO-B) Band (Toggle)
1:TX Band = Sub (VFO-B) Band Main (VFO-A) Band (Toggle)
2: TX Band = Main (VFO-A) Band
3:TX Band = Sub (VFO-B) Band
P2 0: TX Band = Main (VFO-A) Band
1:TX Band = Sub (VFO-B) Band
P1 0: Main (VFO-A) Band
1:Sub (VFO-B) Band
P2 0: AGC “OFF”
1:AGC “FAST”
2:AGC “MID”
3:AGC “SLOW”
4:AGC “AUTO”
4: VFO A “OFF”, VFO B “OFF”
5:VFO A “ON”, VFO B “OFF”
6: VFO A “OFF”, VFO B “ON”
7:VFO A “ON”, VFO B “ON”
P3 0: AGC “OFF”
1:AGC “FAST”
2:AGC “MID”
3:AGC “SLOW”
4:AGC “AUTO-FAST”
5:AGC “AUTO-MID”
6:AGC “AUTO-SLOW”
IDID
ID IDENTIFICA TION
IDID
Set 12345678910
Read 12345678910
ID;
Answer 12345678910
IDP1 P1 P1 P1 ;
P1 0362: FTDX5000
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 10
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
IFIF
IF INFORMATION
IFIF
Set 12345678910
Read 12345678910
Answer 12345678910
ISIS
IS IF-SHIFT
ISIS
Set 12345678910
Read 12345678910
Answer 12345678910
KMKM
KM KEYER MEMORY
KMKM
Set 1234567~53
Read 12345678910
Answer 1234567~53
KPKP
KP KEY PITCH
KPKP
Set 12345678910
Read 12345678910
Answer 12345678910
KRKR
KR KEYER
KRKR
Set 12345678910
Read 12345678910
Answer 12345678910
KSKS
KS KEY SPEED
KSKS
Set 12345678910
Read 12345678910
Answer 12345678910
KYKY
KY CW KEYING
KYKY
Set 12345678910
Read 12345678910
Answer 12345678910
IF;
IFP1 P1 P1 P2 P2 P2 P2 P2
11 12 13 14 15 16 17 18 19 20
P2 P2 P2 P3 P3 P3 P3 P3 P4 P5
21 22 23 24 25 26 27 28 29 30
P6 P7 P8 P9 P9 P10 ;
ISP1 -/+ P2 P2 P2 P2 ;
ISP1 ;
ISP1 -/+ P2 P2 P2 P2 ;
KMP1 P2 P2 P2 P2 ~ P2 ;
KMP1 ;
KMP1 P2 P2 P2 P2 ~ P2 ;
KPP1 P1 ;
KP ;
KPP1 P1 ;
KRP1 ;
KR ;
KRP1 ;
KSP1 P1 P1 ;
KS ;
KSP1 P1 P1 ;
KYP1 ;
**
**
)
OPERATION
P1 001-117 (Memory Channel) P2 VFO-A Frequency (Hz)
P3 Clarifier Direction +: Plus Shift, --: Minus Shift
Clarifier Offset: 0000 - 9999 (Hz)
P4 0: RX CLAR “OFF” 1: RX CLAR “ON”
P5 0: TX CLAR “OFF” 1: TX CLAR “ON”
P6 MODE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB)
P7 0: VFO 1: Memory 2: Memory Tune 3: Quick Memory Bank (QMB) 4: QMB-MT
P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC
P9: Tone Number (See Page 5: “CTCSS Tone Chart”) 00 ~ 49
P10 0: Simplex 1: Plus Shift 2: Minus Shift
P1 0:Main (VFO-A) Band Receiver
P2--1000 ~ +1000 Hz
P1 1 - 5 : Keyer Memory Channel Number
P2 Message Characters (up to 50 characters)
When the message is complete, add the "" character at the end to signify the termination of the message.
ex. KM CQ ~ ; ( space)
P1 00 ~75: 300 Hz ~ 1050 Hz (10 Hz Step)
P1 0: KEYER “OFF”
P1 004 - 060 (WPM)
P1 1: Keyer Memory “1” Playback 6: Message Keyer “1” Playback
7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM
B: FM-N C: PKT-U
1: Sub (VFO-B) Band Receiver
1:KEYER “ON”
2: Keyer Memory “2” Playback 7: Message Keyer “2” Playback
3: Keyer Memory “3” Playback 8: Message Keyer “3” Playback
4: Keyer Memory “4” Playback 9: Message Keyer “4” Playback
5: Keyer Memory “5” Playback A: Message Keyer “5” Playback
LKLK
LK LOCK
LKLK
Set 12345678910
Read 12345678910
Answer 12345678910
LKP1 ;
LK;
LKP1 ;
Page 11
P1 0: VFO A “OFF” (SET Only)
1:VFO A “ON” (SET Only)
2: VFO B “OFF” (SET Only)
3:VFO B “ON” (SET Only)
4: VFO A “OFF”, VFO B “OFF”
5:VFO A “ON”, VFO B “OFF”
6: VFO A “OFF”, VFO B “ON”
7:VFO A “ON”, VFO B “ON”
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
LMLM
LM LOAD MESSAGE
LMLM
Set 12345678910
Read 12345678910
Answer 12345678910
MAMA
MA MEMORY CHANNEL T O VFO-A
MAMA
Set 12345678910
Read 12345678910
Answer 12345678910
MCMC
MC MEMORY CHANNEL
MCMC
Set 12345678910
Read 12345678910
Answer 12345678910
MDMD
MD OPERA TING MODE
MDMD
Set 12345678910
Read 12345678910
Answer 12345678910
MGMG
MG MIC GAIN
MGMG
Set 12345678910
Read 12345678910
Answer 12345678910
MKMK
MK MODE KEY
MKMK
Set 12345678910
Read 12345678910
Answer 12345678910
LMP1 P2 ;
LMP1 ;
LMP1 P2 ;
MA ;
MCP1 P1 P1 ;
MC ;
MCP1 P1 P1 ;
MDP1 P2 ;
MDP1 ;
MDP1 P2 ;
MGP1 P1 P1 ;
MG ;
MGP1 P1 P1 ;
MKP1 ;
)
OPERATION
P1 0: DVS P2 When P1=0 When P1=1
1: P. B 0: DVS (Recording Stop) 0: P.B (Recording Stop)
P1 001 - 117: Memory Channel Number
P1 0: Main (VFO-A) Band
1:Sub (VFO-B) Band
P2 MODE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB)
P1 000 - 255
P1 KEY 0: LSB
7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM
B: FM-N C: PKT-U
1: USB
2: CW
3: AM / FM
4: FM / FM
5: RTTY
6: PKT
1: DVS (CH “1” Recording Start/Stop) 1: P.B (Recording Start)
2: DVS (CH “2” Recording Start/Stop)
3: DVS (CH “3” Recording Start/Stop)
4: DVS (CH “4” Recording Start/Stop)
5: DVS (CH “5” Recording Start/Stop)
001 - 099: Regular Memory Channel
100: P1L
101: P1U
~
116: P9L
117: P9U
MLML
ML MONITOR LEVEL
MLML
Set 12345678910
Read 12345678910
Answer 12345678910
MRMR
MR MEMORY CHANNEL READ
MRMR
Set 12345678910
Read 12345678910
Answer 12345678910
MLP1 P2 P2 P2 ;
MLP1 ;
MLP1 P2 P2 P2 ;
MRP1 P1 P1 ;
MRP1 P1 P1 P2 P2 P2 P2 P2
11 12 13 14 15 16 17 18 19 20
P2 P2 P2 P3 P3 P3 P3 P3 P4 P5
21 22 23 24 25 26 27 28 29 30
P6 P7 P8 P9 P9 P10 ;
P1 0: MONI “ON/OFF”
1: MONI Level
P2 When P1=0
000: MONI “OFF”
001: MONI “ON”
When P1=1
001 - 255
P1 Memory Channel Number P2 Memory Channel Frequency (Hz)
P3 Clarifier Direction +: Plus Shift, --: Minus Shift
Clarifier Offset: 0000 - 9999 (Hz)
P4 0: RX CLAR “OFF” 1: RX CLAR “ON”
P5 0: TX CLAR “OFF” 1: TX CLAR “ON”
P6 MODE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB)
P7 0: VFO 1: Memory
P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC
P9: Tone Number (See Page 5: “CTCSS Tone Chart”) 00 ~ 49
P10 0: Simplex 1: Plus Shift 2: Minus Shift
7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM
B: FM-N C: PKT-U
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 12
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
MSMS
MS METER SW
MSMS
Set 12345678910
Read 12345678910
Answer 12345678910
MWMW
MW MEMOR Y CHANNEL WRITE
MWMW
Set 12345678910
Read 12345678910
Answer 12345678910
MXMX
MX MOX SET
MXMX
Set 12345678910
Read 12345678910
Answer 12345678910
NN
AA
N
A NARROW
NN
AA
Set 12345678910
Read 12345678910
Answer 12345678910
NBNB
NB NOISE BLANKER STATUS
NBNB
Set 12345678910
Read 12345678910
Answer 12345678910
NLNL
NL NOISE BLANKER LEVEL
NLNL
Set 12345678910
Read 12345678910
Answer 12345678910
NRNR
NR NOISE REDUCTION
NRNR
Set 12345678910
Read 12345678910
Answer 12345678910
OIOI
OI OPPOSITE BAND INFORMATION
OIOI
Set 12345678910
Read 12345678910
Answer 12345678910
MSP1 ;
MS ;
MSP1 ;
MWP1 P1 P1 P2 P2 P2 P2 P2
11 12 13 14 15 16 17 18 19 20
P2 P2 P2 P3 P3 P3 P3 P3 P4 P5
21 22 23 24 25 26 27 28 29 30
P6 P7 P8 P9 P9 P10 ;
MXP1 ;
NX ;
NXP1 ;
MAP1 P2 ;
NAP1 ;
NAP1 P2 ;
NBP1 P2 ;
NBP1 ;
NBP1 P2 ;
NLP1 P2 P2 P2 ;
NLP1 ;
NLP1 P2 P2 P2 ;
NRP1 P2 ;
NRP1 ;
NRP1 P2 ;
OI ;
OIP1 P1 P1 P2 P2 P2 P2 P2
11 12 13 14 15 16 17 18 19 20
P2 P2 P2 P3 P3 P3 P3 P3 P4 P5
21 22 23 24 25 26 27 28 29 30
P6 P7 P8 P9 P9 P10 ;
)
OPERATION
P1 0: COMP
1: ALC
2: PO
3: SWR
4: ID
5: VDD
P1 Memory Channel Number P2 Memory Channel Frequency (Hz)
P3 Clarifier Direction +: Plus Shift, --: Minus Shift
Clarifier Offset: 0000 - 9999 (Hz)
P4 0: RX CLAR “OFF” 1: RX CLAR “ON”
P5 0: TX CLAR “OFF” 1: TX CLAR “ON”
P6 MODE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB)
P7 0: (Fixed)
P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC
P9: Tone Number (See Page 5: “CTCSS Tone Chart”) 00 ~ 49
P10 0: Simplex 1: Plus Shift 2: Minus Shift
P1 0: MOX “OFF”
P1 0: Main (VFO-A) Band Receiver
P2 0: OFF
P1 0: Main (VFO-A) Band Receiver
P2 0: Noise Blanker “OFF”
P1 0: Main (VFO-A) Band Receiver
P2 000 - 255
P1 0: Main (VFO-A) Band Receiver
P2 0: Noise Reduction “OFF”
P1 Current Memory Channel P2 VFO-B Frequency (Hz)
P3 Clarifier Direction +: Plus Shift, --: Minus Shift
P4 0: RX CLAR “OFF” 1: RX CLAR “ON”
P5 0: TX CLAR “OFF” 1: TX CLAR “ON”
P6 MODE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB)
P7 0: VFO 1: Memory
P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC
P9: Tone Number (See Page 5: “CTCSS Tone Chart”) 00 ~ 49
P10 0: Simplex 1: Plus Shift 2: Minus Shift
7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM
B: FM-N C: PKT-U
1: MOX “ON”
1: Sub (VFO-B) Band Receiver
1: ON
1:Sub (VFO-B) Band Receiver
1: Noise Blanker “ON”
2: Noise Blanker (Wide) “ON”
1:Sub (VFO-B) Band Receiver
1:Sub (VFO-B) Band Receiver
1: Noise Reduction “ON”
Crarifier Offset: 0000 - 9999 (Hz)
7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM
B: FM-N C: PKT-U
Page 13
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
OSOS
OS OFFSET (REPEA TER SHIFT)
OSOS
Set 12345678910
Read 12345678910
Answer 12345678910
PP
AA
P
A PRE-AMP (IPO)
PP
AA
Set 12345678910
Read 12345678910
Answer 12345678910
PBPB
PB PLAY BACK
PBPB
Set 12345678910
Read 12345678910
Answer 12345678910
PCPC
PC POWER CONTROL
PCPC
Set 12345678910
Read 12345678910
Answer 12345678910
PLPL
PL SPEECH PROCESSOR LEVEL
PLPL
Set 12345678910
Read 12345678910
Answer 12345678910
PRPR
PR SPEECH PROCESSOR
PRPR
Set 12345678910
Read 12345678910
Answer 12345678910
PSPS
PS POWER SWITCH
PSPS
Set 12345678910
Read 12345678910
Answer 12345678910
QIQI
QI QMB STORE
QIQI
Set 12345678910
Read 12345678910
OSP1 P2 ;
OSP1 ;
OSP1 P2 ;
PAP1 P2 ;
PAP1 ;
PAP1 P2 ;
PBP1 P2 ;
PBP1 ;
PBP1 P2 ;
PCP1 P1 P1 ;
PC;
PCP1 P1 P1 ;
PLP1 P1 P1 ;
PL;
PLP1 P1 P1 ;
PRP1 ;
PR;
PRP1 ;
PSP1 ;
PS ;
PSP1 ;
QI ;
)
OPERATION
P1 0: Main (VFO-A) Band
1:Sub (VFO-B) Band
P2 0: Simplex
1: Plus Shift
2:Minus Shift
: FM mode only
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 0:IPO 1
1: AMP 1
2: AMP 2
3: IPO 2
P1 0: DVS P2 When P1=0 When P1=1
1: P.B 0: DVS (Recording Stop) 0: P.B (Playback Stop)
P1 000 - 255
P1 000 - 255
P1 0: Speech Processor “OFF”
1: Speech Processor “ON”
2: Microphone Equalizer “ON”
P1 0:POWER “OFF”
1: POWER “ON” (Send the PS1; command twice every one second.)
1: DVS (CH “1” Playback Start) 1: P.B (Playback Start)
2: DVS (CH “2” Playback Start)
3: DVS (CH “3” Playback Start)
4: DVS (CH “4” Playback Start)
5: DVS (CH “5” Playback Start)
Answer 12345678910
QRQR
QR QMB RECALL
QRQR
Set 12345678910
Read 12345678910
Answer 12345678910
QR ;
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 14
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
QSQS
QS QUICK SPLIT
QSQS
Set 12345678910
Read 12345678910
Answer 12345678910
RARA
RA RF A TTENUA TOR
RARA
Set 12345678910
Read 12345678910
Answer 12345678910
RR
CC
R
C CLAR CLEAR
RR
CC
Set 12345678910
Read 12345678910
Answer 12345678910
RDRD
RD CLAR MINUS OFFSET
RDRD
Set 12345678910
Read 12345678910
QS ;
RAP1 P2 ;
RAP1 ;
RAP1 P2 ;
RC ;
RDP1 P1 P1 P1 ;
)
OPERATION
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 0: OFF
1: 6 dB
2: 12 dB
3: 18 dB
P1 0000 - 9999 (Hz)
Answer 12345678910
RFRF
RF ROOFING FILTER
RFRF
Set 12345678910
Read 12345678910
Answer 12345678910
RR
GG
R
G RF GAIN
RR
GG
Set 12345678910
Read 12345678910
Answer 12345678910
RIRI
RI RADIO INFORMA TION
RIRI
Set 12345678910
Read 12345678910
Answer 12345678910
RLRL
RL NOISE REDUCTION LEVEL
RLRL
Set 12345678910
Read 12345678910
Answer 12345678910
RMRM
RM READ METER
RMRM
Set 12345678910
Read 12345678910
Answer 12345678910
RFP1 P2 ;
RFP1 ;
RFP1 P3 ;
RGP1 P2 P2 P2 ;
RGP1 ;
RGP1 P2 P2 P2 ;
RIP1 ;
RIP1 P2 ;
RLP1 P2 P2 ;
RLP1 ;
RLP1 P2 P2 ;
RMP1 ;
RMP1 P2 P2 P2 ;
P1
0: Main (VFO-A)
Band Receiver
1: Sub (VFO-B)
Band Receiver
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 000 - 255
P1 0:Hi-SWR
1:MIC-EQ
2: CLASS-A
3: REC
4: PLAY
5: MAIN TX
6: SUB TX
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 01 - 15
P1 0: Depends of the front panel’s METER knob
1: S Meter (Main) 5: PO Meter
2: S Meter (Sub) 6: SWR Meter
3:COMP Meter 7: ID Meter
4: ALC Meter 8: VDD Meter
P2 0 - 255
P2 0: AUTO
1: 15 kHz
2: 6 kHz
3: 3 kHz
4: 600 Hz (Main)
5: 300 Hz (Main)
7: MAIN RX
8: SUB RX
P3 1: 15 kHz
2: 6 kHz
3: 3 kHz
4: AUTO - 15 kHz
5: AUTO - 6kHz
6: AUTO - 3 kHz
7: 600 Hz (Main)
P2 0: OFF
1: ON
8: 300 Hz (Main)
9: AUTO - 600 Hz (Main)
A: AUTO - 300 Hz (Main)
Page 15
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
RR
OO
R
O ROTATOR
RR
OO
Set 12345678910
Read 12345678910
Answer 12345678910
RSRS
RS RADIO STA TUS
RSRS
Set 12345678910
Read 12345678910
Answer 12345678910
RR
TT
R
T CLAR
RR
TT
Set 12345678910
Read 12345678910
Answer 12345678910
RR
UU
R
U RX CLARIFIER PLUS OFFSET
RR
UU
Set 12345678910
Read 12345678910
ROP1 ;
RO ;
ROP1 P2 P2 P2 P3 P3 P3 ;
RS ;
RSP1 ;
RTP1 ;
RT ;
RTP1 ;
RUP1 P1 P1 P1 ;
P1 0: OFF
1: Counter Clockwise
2: Clockwise
3: SPEED 1 % DOWN
4: SPEED 1 % UP
P2 DIRECTION (0 - 450)
P3 SPEED (0 - 100 %)
P1 0: NORMAL MODE
1: MENU MODE
P1 0: RX Clarifier “OFF”
1: RX Clarifier “ON”
P1 0000 - 9999 (Hz)
)
OPERATION
Answer 12345678910
SCSC
SC SCAN
SCSC
Set 12345678910
Read 12345678910
Answer 12345678910
SDSD
SD CW BREAK-IN DELAY TIME
SDSD
Set 12345678910
Read 12345678910
Answer 12345678910
SFSF
SF SUB VFO-B KNOB FUNCTION
SFSF
Set 12345678910
Read 12345678910
Answer 12345678910
SHSH
SH WIDTH
SHSH
Set 12345678910
Read 12345678910
Answer 12345678910
SCP1 ;
SC;
SCP1 ;
SDP1 P1 P1 P1 ;
SD;
SDP1 P1 P1 P1 ;
SFP1 P1 ;
SF;
SFP1 P1 ;
SHP1 P2 P2 ;
SHP1 ;
SHP1 P2 P2 ;
P1 0:Scan “OFF”
1: Scan “ON” (Upward)
2: Scan “ON” (Downward)
P1 0020 - 5000 (mS)
P1 00: BAND
01: -
02: GRP
03: MCH
04: -
05: -
06: -
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 00 [Default]
SSB NARROW 01: 200 02: 400 03: 600 04: 850 05: 1100
SSB WIDE 07: 1500 08: 1650 09: 1800 10: 1950 11: 2100
CW NARROW 01: 50 02: 100 03: 150 04: 200 05: 250
CW WIDE 10: 500 11: 800 12: 1200 13: 1400 14: 1700
RTTY NARROW 01: 50 02: 100 03: 150 04: 200 05: 250
RTTY WIDE 10: [500] 11: 800 12: 1200 13: 1400 14: 1700
PSK NARROW 01: 50 02: 100 03: 150 04: 200 05: 250
PSK WIDE 10: [500] 11: 800 12: 1200 13: 1400 14: 1700
07: S-DIAL
08: CLAR
06: 1350 07: [1500]
12: 2250 13: [2400] 14: - - - - 15: 2500 16: 2600
17: 2700 18: 2800 19: 2900 20: 3000 21: 3200
22: 3400 23: 3600 24: 3800 25: 4000
06: 300 07: 350 08: 400 09: 450 10: [500]
15: 2000 16: [2400]
06: [300] 07: 350 08: 400 09: 450 10: 500
15: 2000 16: 2400
06: [300] 07: 350 08: 400 09: 450 10: 500
15: 2000 16: 2400
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 16
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
SMSM
SM S-METER READING
SMSM
Set 12345678910
Read 12345678910
Answer 12345678910
SQSQ
SQ SQUELCLH LEVEL
SQSQ
Set 12345678910
Read 12345678910
Answer 12345678910
SVSV
SV SWAP VFO
SVSV
Set 12345678910
Read 12345678910
Answer 12345678910
SMP1 ;
SMP1 P2 P2 P2 ;
SQP1 P2 P2 P2 ;
SQP1 ;
SQP1 P2 P2 P2 ;
SV;
)
OPERATION
P1 0: Main (VFO-A) Band S-meter
1:Sub (VFO-B) Band S-meter
P2 000 - 255
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 000 - 255
TSTS
TS TXW
TSTS
Set 12345678910
Read 12345678910
Answer 12345678910
TXTX
TX TX SET
TXTX
Set 12345678910
Read 12345678910
Answer 12345678910
ULUL
UL PLL UNLOCK STATUS
ULUL
Set 12345678910
Read 12345678910
Answer 12345678910
UPUP
UP MIC UP
UPUP
Set 12345678910
Read 12345678910
Answer 12345678910
TSP1 ;
TS;
TSP1 ;
TXP1 ;
TX;
TXP1 ;
UL ;
ULP1 ;
UP ;
P1 0:TXW “OFF”
1:TXW “ON”
P1 0: RADIO TX “OFF” CAT TX “OFF”
1:RADIO TX “OFF” CAT TX “ON”
2:RADIO TX “ON” CAT TX “OFF” (Answer)
P1 0: PLL “Lock”
1:PLL “Unlock”
VDVD
VD VOX DELAY TIME
VDVD
Set 12345678910
Read 12345678910
Answer 12345678910
VFVF
VF VRF FILTER
VFVF
Set 12345678910
Read 12345678910
Answer 12345678910
VDP1 P1 P1 P1 ;
VD ;
VDP1 P1 P1 P1 ;
VFP1 P2 P3 P4 ;
VFP1;
VFP1 P2 P5 P5 P5 P6 ;
Page 17
P1 0020 - 5000 mS (20 mS multiples)
P1 0: Main (VFO-A) Band Receiver
1:Sub (VFO-B) Band Receiver
P2 0: OFF
1: ON
2: Default set
P3 +: Plus Shift
–: Minus Shift
P4 0 - 9 (Step)
P5 000 - 255
P6 0: VRF
1: μTUNE
FTDX5000 SERIES CAT OPERATION REFERENCE
CAT
(
COMPUTER AIDED TRANSCEIVER
CONTROL COMMAND TABLES
VV
GG
V
G VOX GAIN
VV
GG
Set 12345678910
Read 12345678910
Answer 12345678910
VMVM
VM VFO-A TO MEMOR Y CHANNEL
VMVM
Set 12345678910
Read 12345678910
Answer 12345678910
VSVS
VS VFO SELECT
VSVS
Set 12345678910
Read 12345678910
Answer 12345678910
VXVX
VX VOX STATUS
VXVX
Set 12345678910
Read 12345678910
Answer 12345678910
XTXT
XT TX CLAR
XTXT
Set 1213 4 5 6 7 8 910
Read 12345678910
Answer 12345678910
VGP1 P1 P1 ;
VG;
VGP1 P1 P1 ;
VM;
VSP1 ;
VS ;
VSP1 ;
VXP1 ;
VX ;
VXP1 ;
XTP1 ;
XT;
XTP1 ;
P1 000 - 255
P1 0: VFO-A
1: VFO-B
P1 0:VOX “OFF”
1:VOX “ON”
P1 0: TX CLAR “OFF”
1:TX CLAR “ON”
)
OPERATION
FTDX5000 SERIES CAT OPERATION REFERENCE
Page 18
CAT
(
COMPUTER AIDED TRANSCEIVER
)
OPERATION
Copyright 2010
VERTEX STANDARD CO., LTD.
All rights reserved
No portion of this manual
may be reproduced without
the permission of
VERTEX STANDARD CO., LTD.
EH036H120
FTDX5000 SERIES CAT OPERATION REFERENCE
Loading...