YAESU FTDX-3000 brochure

HF/50 MHz 100 W Transceiver

FT DX

NewCrystalRoofingFiltersprovideultimateweaksignalreceiver

performanceincrowded,strongsignalenvironments

3000

e amazing Crystal Roofing Filter performance
has been proven in the FT

The Down conversion 9 MHz 1st IF frequency receiver construction, can realize
narrow 300 Hz (optional), 600 Hz and 3 kHz bandwidth roofing filters.
Implementing the extra sharp Crystal Roofing Filters provides superior close-in
dynamic range and affords the best receiver performance possible.

300 Hz, 600 Hz, 3 kHz Crystal roofing Filters Characteristics of the Crystal Roofing Filter (300 Hz)

DX 5000!

CENTER: 9 MHz SPAN: 20 kHz

Outstanding receiver performance
is the heritage of the FT

The essential elements in receiver performance are the RF amplifier and the 1st mixer.
YAESU pursued the ultimate performance of these circuits. The RF amplifier has
optimized NF points, and the over-sized wide range RF transformer exhibits minimum
saturation in strong signal processing. The optimized devices were selected to
guarantee superior multi-signal RX performance. The desired maximum performance
has been realized in the development of the
FTDX3000 receiver circuitry. The FTDX3000
has the high dynamic range IP3 performance
that was realized and proven in the FTDX5000.

DX 5000

14 MHz BAND CW (BW = 500 Hz)
IPO ON, Roofing FILTER = 600 Hz
2 kHz Spacing

RX OUTPUT [dB]

DR : 106 dB

-20 dBm-126 dBm

SIG

IP3 : +33 dBm

3rd IMD

Large and wide color LCD display

The 3.5-inch wide color LCD displays the operating information and the status of
the transceiver functions, with high resolution (480 x 272 dots) on the screen.
The various FTDX3000 functions are displayed on this LCD and provide the
operator with easy to read operating information.

High Speed Spectrum Scope built-in

Although the FTDX3000 has only one receiver, a high speed Spectrum Scope is
built into the radio. When in the Auto Mode, the Spectrum Scope display is
updated in real time. The maximum bandwidth of the scope is 1 MHz, and the
minimum span width setting is 20 kHz. The best desired span is selectable for the
high resolution display. The current band activity can be monitored in real time.

AF SCOPE display and RTTY/PSK encoder/decoder (optional)

Optional AF SCOPE and optional RTTY encoder/decoder functions have been
developed.
The wave form of the AF SCOPE signal can be displayed on the TFT LCD. Also,
the RTTY/PSK text may be displayed on the LCD.

Independent Frequency display

The Main operating frequency is the most important display in the radio, VFO-A
frequency is located just above the main dial. The newly developed LCD has a
wider viewing angle and higher contrast for convenient and effortless viewing.

Other features

• The specialized Receiver amplifier for 50 MHz is built in

• Three antenna connectors are provided.

The “ANT-3” terminal may be assigned to “RX-only”

• Signal output for an external receiver and the 9 MHz IF output are furnished

• High speed Automatic antenna tuner built in

• Optional μ-tune unit available

• USB interface equipped

RF amp with the large size
wide range transformer

The 1st mixer that provides
optimum reception performance

3rd Order Dynamic Range / IP3

ANT INPUT [dBm]

IF DSP provides effective and optimized QRM rejection

The 32 bit high speed floating decimal DSP (max 2800 MIPS) provides effective
cancellation/reduction (DNR) of the random noise that is frequently frustrating in
the HF frequencies. Also: the AUTO NOTCH (DNF) that automatically eliminates
the dominant beat tone, the CONTOUR, and the APF, are very effective receiver
noise reduction tools in the HF bands operations. The YAESU original DSP QRM
and noise reduction functions are provided.

FTDX3000 Specifications

General

RX Frequency Range: 30 kHz - 56 MHz (opera ting)

1.8 MHz - 5 4 M Hz (specified performance, Amateur bands only)

TX Frequency Ranges: 1.8 MHz - 54 MHz (Amateur bands only)
Frequency Stabilit y: ± 0.5 ppm (after 1 minute @+14 °F to +122 °F [–10 °C to +50 °C])
Operating Temperature Range: +14 °F to +122 °F (–10 °C to +50 °C)
Emission Modes: A1A (CW), A3E (A M), J3E (LSB, USB), F3E (FM),

F1B (RTTY ), F1D (PACK ET), F2D (PACKE T)

Frequency Steps: 1/10 Hz (SSB, CW, & AM), 100 Hz (FM)
Antenna Impedance: 50 Ohms, unbalanced

16.7 - 150 Ohms, unbalanced (1.8 - 29.7 MHz)
25 - 100 Ohms, unbalanced (50 - 54 MHz)
(Tuner ON, 1.8 MH z - 50 MHz Amateur bands, TX only)
Power Consumption (A pprox.): RX (no signal) 1.8 A
RX (signal present) 2.1 A
TX (100 W) 23 A

Supply Voltage: DC 13.8 V ± 10% (Nega tive Gr ound )
Dimensions (WxH xD): 14.4” x 4.5” x 12.3” (365 x 115 x 312 mm)
Weight (Approx.): 22.0 lbs (10 kg)

This dev ice has not bee n approved by the FCC. Thi s device may not be of fered for sale or le ase or be sold or l eased until appro val of the FCC has be en obtained.
The infor mation shown is pre liminary and ma y be subject to ch ange without noti ce or obligati on.

Transmitter

Power Output: 5 - 100 watts (2 - 25 watts AM carrier)
Modulation Types: J3E (SSB): Balanced,
A3E (AM ): Low-Level (Early Stage),
F3E (FM): Variable React ance
Maximum FM Deviation: ±5.0 kHz/ ±2.5 kHz
Harmonic Radiation: Bett er than -60 dB (1.8 MHz - 29.7 MHz Amateur bands: Harmonics)

Better than -50 dB (1.8 MHz - 29.7 MHz Amateur bands: Others)
Better than -65 dB (50 MHz Amateur band)

SSB Carrier Suppres sion: A t least 60 dB below peak output
Undesired Sideband Suppression: A t least 60 dB below peak output
3rd-order IMD: –31 dB @14 MHz 100 watts PEP
Bandwidth: 3 kHz (LS B/USB), 500 Hz (CW), 6 kHz (A M), 16 kHz (FM )
Audio Response (SSB): Not more than -6 dB from 300 t o 270 0 H z
Microphone Impedance: 600 Ohms (200 to 10k Ohms)

Receiver

Circuit Type: Double-conversion Superheterodyne
Intermediate Frequencies: 9.000 MHz/ 30 kHz (24 kHz for AM/ FM)

Rear pane l view

Sensitivit y: SSB (BW: 2.4 kHz, 10 dB S+N/N )
4 µV (0.5 - 1.8 MHz) ( IPO “ON”)

0.16 µV (1.8 - 30 MHz) (RF AMP 2 “ON”)

0.125 µV (50 - 54 MHz) (R F AMP 2 “ON”)
AM (BW: 6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz)
28 µV (0.5 - 1.8 MHz) ( IPO “ON”)
2 µV (1.8 - 3 0 MHz) (RF AMP 2 “ON”)
1 µV (50 - 54 MHz) (RF AMP 2 “ON”)
FM (BW: 15 kHz, 12 dB SIN AD)

0.5 µV (28 - 30 MHz) (RF AMP 2 “ON”)

0.35 µV (50 - 54 MHz) (RF AMP 2 “ON”)
There is no specification for frequency ranges not listed.
Selectivit y ( WIDTH: Center): Mode -6 dB -60 dB
CW/RT TY/PKT 0.5 kHz or bet ter 750 Hz or les s
SSB 2.4 kHz or better 3.6 kHz or less
AM 6 kHz or better 15 kHz or less
FM 15 kHz or better 25 kHz or less
Image Rejection: 70 dB or better (1.8 MHz - 30MHz Amateur bands)
60 dB or better (50 - 54MHz Amat eur band)

Maximum Audio Output: 2.5 W into 4 Ohms with 10% THD
Audio Output Impedance: 4 to 8 Ohms (4 Ohms: nominal)
Conducted Radiation: Less than 4 nW

2012.0503SS(USA/EXP/EU) B9200639 Printed in Japan

YAESU MUSEN CO., LTD.

http://www.yaesu.com/jp

Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002, Japan

YAESU USA

US Headquarters

YAESU UK

Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.

YAESU HK

Unit 1306-1308, 13F., Millennium City 2, 378 Kwun Tong Road,
Kwun Tong, Kowloon, Hong Kong

http://www.yaesu.com

6125 Phyllis Drive, Cypress, CA 90630, U.S.A.

http://www.yaesu.co.uk

http://www.yaesu.com.hk