Whirlpool WRX986SIHV, WRX986SIHZ Maintance Manual

REFRIGERATOR

USER INSTRUCTIONS

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING or PROBLEM SOLVER, please visit our website at www.whirlpool.com for additional information. If you still need assistance, call us at 1-800-253-1301. In Canada, visit our website at www.whirlpool.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Table of Contents / Índice / Table des matières

REFRIGERATOR SAFETY .......................	2
Proper Disposal of
Your Old Refrigerator.............................	3
INSTALLATION INSTRUCTIONS............	3
Unpack the Refrigerator.........................	3
Remove and Replace
Refrigerator Doors..................................	4
Remove and Replace Drawer Fronts ....	7
Location Requirements..........................	9
Electrical Requirements .........................	9
Water Supply Requirements..................	9
Connect the Water Supply ..................	10
Handle Installation and Removal.........	11
Refrigerator Leveling,
Door Closing and Alignment................	12
FILTERS AND ACCESSORIES..............	13
Water Filtration System........................	13
Install Air Filter......................................	14
Accessories..........................................	15
REFRIGERATOR USE............................	15
Opening and Closing Doors ................	15
Using the Controls ...............................	15
Refrigerator Features ...........................	18
Water and Ice Dispensers....................	19
Ice Maker and Ice Storage Bin ............	22
REFRIGERATOR CARE .........................	22
Cleaning ...............................................	22
Lights....................................................	23
Vacation and Moving Care ..................	23
PROBLEM SOLVER ...............................	24
WATER FILTER CERTIFICATIONS.......	29
PERFORMANCE DATA SHEET ............	30
WARRANTY ............................................	31

SEGURIDAD DEL REFRIGERADOR.....	32
Cómo deshacerse adecuadamente
de su refrigerador viejo ........................	33
INSTRUCCIONES DE INSTALACIÓN...	33
Desempaque el refrigerador ................	33
Cómo quitar y volver a colocar
las puertas del refrigerador ..................	34
Cómo quitar y volver a colocar
los frentes de los cajones ....................	36
Requisitos de ubicación.......................	38
Requisitos eléctricos............................	39
Requisitos del suministro de agua.......	39
Conexión del suministro de agua ........	39
Instalación y remoción
de las manijas.......................................	41
Nivelación del refrigerador, cierre
y alineamiento de las puertas ..............	42
FILTROS Y ACCESORIOS .....................	43
Sistema de filtración de agua ..............	43
Instalación del filtro de aire ..................	44
Accesorios............................................	45
USO DE SU REFRIGERADOR...............	46
Cómo abrir y cerrar las puertas ...........	46
Uso de los controles ............................	46
Características del refrigerador............	49
Despachadores de agua y hielo ..........	49
Fábrica de hielo y depósito de hielo....	53
CUIDADO DE SU REFRIGERADOR .....	53
Limpieza ...............................................	53
Luces ....................................................	54
Cuidado durante las
vacaciones y mudanzas.......................	55
SOLUCIÓN DE PROBLEMAS................	56
HOJA DE DATOS
DEL RENDIMIENTO ...............................	62
GARANTÍA...............................................	63

SÉCURITÉ DU RÉFRIGÉRATEUR........	65
Mise au rebut adéquate de
votre vieux réfrigérateur.......................	66
INSTRUCTIONS D’INSTALLATION......	66
Déballage du réfrigérateur...................	66
Retrait et réinstallation des
portes du réfrigérateur.........................	67
Retrait et réinstallation
de l'avant des tiroirs ............................	69
Exigences d'emplacement..................	71
Spécifications électriques ...................	72
Spécifications de
l’alimentation en eau............................	72
Raccordement à la
canalisation d'eau................................	72
Installation et démontage
des poignées .......................................	74
Mise à niveau du réfrigérateur,
fermeture et alignement des portes ....	75
FILTRES ET ACCESSOIRES.................	76
Système de filtration d'eau..................	76
Installation du filtre à air.......................	77
Accessoires .........................................	78
UTILISATION DU RÉFRIGÉRATEUR ...	78
Ouverture et fermeture des portes......	78
Utilisation des commandes.................	78
Caractéristiques du réfrigérateur ........	81
Distributeurs d'eau et de glaçons .......	82
Machine à glaçons et bac
d’entreposage à glaçons.....................	85
ENTRETIEN DU RÉFRIGÉRATEUR .....	86
Nettoyage ............................................	86
Lampes ................................................	87
Entretien avant les vacances
ou lors d’un déménagement ...............	87
RÉSOLUTION DE PROBLÈMES ..........	88
FEUILLE DE DONNÉES
SUR LA PERFORMANCE......................	94
GARANTIE..............................................	95

W10505281A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

	■ Plug into a grounded 3 prong outlet.	■ Use nonflammable cleaner.
	■ Do not remove ground prong.	■ Keep flammable materials and vapors, such as gasoline,
	■ Do not use an adapter.	away from refrigerator.
		■ Use two or more people to move and install refrigerator.
	■ Do not use an extension cord.
		■ Disconnect power before installing ice maker (on ice maker
	■ Disconnect power before servicing.
		kit ready models only).
	■ Replace all parts and panels before operating.
		■ Use a sturdy glass when dispensing ice (on some models).
	■ Remove doors from your old refrigerator.
		■ Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

2

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may not easily climb inside.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Remove the Packaging

Clean Before Using

■Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

■Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”

■Dispose of/recycle all packaging materials.

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Refrigerator Care.”

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

3

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your door opening, to see whether or not you need to remove the refrigerator doors to move the refrigerator into your home. If door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator control OFF. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors.

TOOLS NEEDED: ³⁄" hex key wrench and a #2 Phillips screwdriver

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Style 1 – Water Dispenser

Tubing Connection

A

A. Outer Ring

Wiring Plug

Door Removal and Replacement
Style 2 – Water Dispenser	Door Removal	Top Right Hinge
Tubing Connection		B
		C
		A
		D
		A. ³⁄" Internal Hex-Head Screws
		B. Hinge Cover Screw
		C. Top Hinge Cover
		D. Top Hinge
A
A. Outer Ring

Top Left Hinge
A	B
C
A. ³⁄" Internal Hex-Head Screws
B. Ground Wire (Do Not Remove)
C. Do Not Remove Screws

4

Remove Right-Hand Refrigerator Door

WARNING

Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1.Unplug refrigerator or disconnect power.

2.Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

3.Using a Phillips screwdriver, remove the cover from the Top Hinge.

4.Using the ³⁄" hex key wrench, remove the two internal hex head screws from the top hinge, and set aside.

NOTE: Do not remove the two locator screws. These screws will help you align the hinge when you replace the door.

A

B

C

D

Remove Left-Hand Refrigerator Door

IMPORTANT: The tubing and wiring for the water dispenser run through the left-hand door hinge, so they must be disconnected before removing the door.

1.Using a Phillips screwdriver, remove the cover from the top hinge.

A

B

A. Top hinge cover screw

B. Top hinge cover

2.Disconnect the water dispenser tubing located on top of the door hinge.

Style 1 - Press the outer ring against the face of the fitting and gently pull the dispenser tubing free.

NOTE: The water dispenser tubing remains attached to the left-hand refrigerator door.

A B

A. Top hinge cover screw	C. ³⁄" Internal hex head screws
B. Top hinge cover	D. Top hinge	A. Outer ring
		B. Face of fitting

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

5.Lift the refrigerator door from the bottom hinge pin. The top hinge will come away with the door.

5

Style 2 - Firmly pull up on the clasp. Then, pull the tubing out of the fitting.

NOTE: The water dispenser tubing remains attached to the left-hand refrigerator door.

3.Disconnect the wiring plug located on top of the door hinge.

■Grasp each side of the wiring plug. With your left thumb, press down to release the catch and pull the sections of the plug apart.

NOTE: Do not remove the green, ground wire. It should remain attached to the door hinge.

4.Using the ³⁄" hex key wrench, remove the two internal hex head screws from the top hinge, and set aside.

NOTES:

■Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

■Do not remove the two locator screws. These screws will help you align the hinge when you replace the door.

A B

5.Lift the refrigerator door from the bottom hinge pin. The top hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges and brake feet assemblies to move the refrigerator through a doorway.

■Only if necessary, use a driver with a #2 square bit tip to remove the bottom hinges and a ³⁄" nut driver to remove the brake feet screws.

Replace Right-Hand Refrigerator Door

1.Set the right-hand door onto the bottom hinge pin.

2.Insert the top hinge pin into the open hole in the top of the refrigerator door.

3.Using the two ³⁄" internal hex head screws, fasten the hinge to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring bundles when reconnecting them.

1.Set the left-hand door onto the bottom hinge pin.

2.Using the two ³⁄" internal hex head screws, fasten the hinge to the cabinet. Do not tighten the screws completely.

3.Reconnect the water dispenser tubing.

Style 1 - Insert the tubing into the fitting until it stops and the outer ring is touching the face of fitting.

Style 2 - Insert the tubing firmly into the fitting until it stops. Close the clasp around the tubing. The clasp snaps into place between the fitting and the collar.

4.Reconnect the electrical wiring.

■ Push together the two sections of the wiring plug.

Final Steps

1.Completely tighten the four internal hex head screws (two on the right-hand door hinge and two on the left-hand door hinge).

2.Replace both top hinge covers.

C

A. ³⁄" Internal hex head screws	C. Locator screws (do not
B. Ground wire (do not remove)	remove)

6

Remove and Replace Drawer Fronts

Depending on the width of your door opening, it may be necessary to remove the drawer fronts to move the refrigerator into your home.

IMPORTANT:

■If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator control OFF, and unplug the refrigerator or disconnect power. Remove food from the drawers.

■Two people may be required to remove and replace the drawer fronts.

Tools Needed: ¹⁄ " Hex head nut driver, Flat-blade screwdriver

Refrigerated Drawer

Disconnect Wiring

NOTES:

■The exterior refrigerator drawer front is connected to the temperature control. Before removing the drawer front, the wires must be disconnected from the temperature control.

■The gray cable visible behind and under the pantry drawer at the right side contains wiring for the pantry control and moves with the drawer as it is pulled out. There is no need to disconnect this cable.

1.Open the drawer to its full extension, and remove the large interior bin.

2.Locate the wiring cover on the backside of the drawer front. Press tab on the cover to release the snaps, and pull off cover to reveal the wiring connection.

3.On one side of the wiring connector, insert the screwdriver blade between the connector tab and the connector to release. Repeat for the opposite side. Pull the wiring connector apart.

Remove Drawer Front

1.Using a ¹⁄ " hex head nut driver, remove the two bottom screws (one on each side) attaching the drawer front to the drawer glides.

2.Using ¹⁄ " hex head nut driver, loosen the two top screws (one on each side) attaching the drawer front to the drawer glides.

NOTE: Loosen the screws three to four turns. Keep the screws in the drawer front.

3.Lift the drawer front up and off the drawer glide brackets.

	A
			A
			B
			C
	B
		A. Loosen top screws	C. Remove bottom screws
A. Press tab	B. Wiring connection cover	B. Drawer glide bracket

4. Slide the drawer glides back into the refrigerator.

7

Replace Drawer Front

1.Pull out the drawer glides until they are fully extended.

2.Lower the loosened screws in the top of the drawer front into the upper notches in the drawer glides.

NOTE: It helps if one person holds the drawer glides steady while another person aligns the drawer front and inserts the screws into the notches.

3.Align the holes in the bottom of the drawer front with the holes in the bottom of the drawer glides and fasten with the screws removed earlier.

4.Tighten the two top screws.

Reconnect Wiring

1.Align the two ends of the wiring connector and push them together until you hear a “click” sound and feel the tabs snap into place on the connector.

2.Gently pull on the wiring connection to ensure the wiring connection is completely seated. Replace the wiring cover.

NOTE: The wiring connection must be complete for the drawer temperature control to operate.

3.Replace the interior bin.

Freezer Drawer

Remove Drawer Front

1.Open the freezer drawer to its full extension.

2.Loosen the two top screws that fasten the drawer front to the drawer glides. The two screws (one on the left-hand side and one on the right-hand side) are located inside the drawer front.

3.Lift up on the drawer front to release the plastic studs from the drawer glide bracket slots.

A

Replace Drawer Front

1.Pull out the freezer drawer glides to their full extension.

2.Holding the drawer front by its sides, align the two plastic studs, located at the bottom, inside the drawer front, with the drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady while another person aligns the drawer front and inserts the studs into the slots.

A

B

A.Drawer front screw

B.Drawer front plastic stud

3.Replace and tighten the two screws at the top of the drawer front (one on the left-hand side and one on the right-hand side).

Final Steps

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug into a grounded 3 prong outlet.

2.Reset the controls. See “Using the Control(s)” and “Temperature Controlled Exterior Drawer.”

3.Return all removable parts and the food to the drawers.

A.Drawer glide bracket slots

4.Slide the drawer glides back into the freezer.

8

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household use only.

To ensure proper ventilation for your refrigerator, allow for a ¹⁄ " (1.25 cm) of space on each side and at the top. Allow for a 1" (2.54 cm) space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave a 3³⁄ " (9.5 cm) minimum space between the refrigerator and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

¹⁄ " (1.25 cm)

3³⁄ " (9.5 cm)

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn Cooling OFF, and then disconnect the refrigerator from the electrical source. When you have finished, reconnect the refrigerator to the electrical source and turn Cooling ON. See “Using the Control(s).”

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

NOTE: If the water pressure is less than what is required, the flow of water from the water dispenser could decrease or ice cubes could be hollow or irregular shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy use. The tank capacity could be too small to keep up with the requirements of the refrigerator.

NOTE: Faucet mounted reverse osmosis systems are not recommended.

■If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed, qualified plumber.

9

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.

■The gray water tubing on the back of the refrigerator (which is used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable, and will help avoid off-taste or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the following Whirlpool Part Numbers:

W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP (25 ft [7.62 m] PEX).

■Install tubing only in areas where temperatures will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

■Flat-blade screwdriver

■⁄ " and ¹⁄ " open-end wrenches or two adjustable wrenches

■¹⁄ " nut driver

NOTE: Do not use a piercing-type or ³⁄ " (4.76 mm) saddle valve which reduces water flow and clogs easier.

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water is connected, turn the ice maker OFF.

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Use a quarter-turn shutoff valve or the equivalent, served by a ¹⁄ " household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a minimum ¹⁄ " size household supply line is recommended.

A

B

C

	D
A. Sleeve	C. Copper tubing (to refrigerator)
B. Nut	D. Household supply line (½" minimum)

4.Now you are ready to connect the copper tubing to the shutoff valve. Use ¹⁄ " (6.35 mm) OD soft copper tubing to connect the shutoff valve and the refrigerator.

■Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

■Slip compression sleeve and compression nut onto copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A B	C
A. Compression sleeve	C. Copper tubing

B.Compression nut

5.Place the free end of the tubing into a container or sink, and turn on main water supply to flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve, to avoid possible water valve malfunction.

6.Bend the copper tubing to meet the water line inlet, which is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specific to your model.

Style 1

1.Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2.Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a “P” clamp.

A

B

C

D

A. Copper tubing	C. Compression nut
B. “P” clamp	D. Compression sleeve

3.Turn on water supply to refrigerator and check for leaks. Correct any leaks.

10

Style 2

1.Unplug refrigerator or disconnect power.

2.Remove and discard the short, black plastic part from the end of the water line inlet.

3.Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet’s side wall or other parts inside the cabinet.

A	B	C	D
	A. Household water line		C. Ferrule (purchased)
	B. Nut (purchased)		D. Refrigerator water tubing

4.Install the water supply tube clamp around the water supply line to reduce strain on the coupling.

5.Turn shutoff valve ON.

6.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

7.On some models, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the ¹⁄ " (6.35 mm) water line at either tube connection. Obtain a water strainer from your appliance dealer.

Complete the Installation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug into a grounded 3 prong outlet.

2.Flush the water system. See “Water and Ice Dispensers.”

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice storage bin.

Handle Installation and Removal

Parts Included: Refrigerator door handles (2), Refrigerator drawer handle (1), Freezer drawer handle (1), ¹⁄ " hex key, spare setscrew(s)

Install Handles

Refrigerator Doors

NOTE: Handle mounting setscrews are preinstalled inside the handle.

1.Remove the handles from the packaging inside the refrigerator, and place them on a soft surface.

2.Open a refrigerator compartment door. On the closed door, place a handle onto the shoulder screws so that the setscrews are facing the adjacent door.

A

B

A.Shoulder screws

B.Setscrews inside the handle

3.Firmly push the handle toward the door until the handle base is flush against the door.

4.While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the setscrew.

5.Using a clockwise motion tighten the setscrew just until it begins to contact the shoulder screw. Do not fully tighten.

6.Repeat steps 4 and 5 to fasten the lower setscrew.

7.Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.

8.Repeat steps 2 through 7 to install the other handle onto the adjacent refrigerator door.

11

Refrigerator and Freezer Drawers

1.With the drawer closed, place the handle onto the shoulder screws so that the setscrews are facing down toward the floor.

A

B

A.Shoulder screw

B.Setscrews inside the handle

2.Firmly push the handle toward the drawer until the handle base is flush against the drawer.

3.Insert the short end of the hex key into the left-hand hole and slightly rotate the hex key until it is engaged in the setscrew.

4.Using a left to right motion tighten the setscrew a quarter-turn at a time just until it begins to contact the shoulder screw. Do not fully tighten.

5.Repeat steps 11 and 12 to fasten the right-hand setscrew to the shoulder screw.

6.Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.

7.Save the hex key and all instructions.

Remove the Handles

1.While holding the handle, insert the short end of the hex key into a setscrew hole and slightly rotate the hex key until it is engaged in the setscrew.

2.Using a right to left motion loosen the setscrew a quarter-turn at a time.

3.Repeat steps 1 and 2 for the other setscrew. Slowly pull the handle away from the door or drawer.

4.If necessary, use a Phillips screwdriver to remove the shoulder screws from the door.

Refrigerator Leveling, Door Closing

and Alignment

The base grille covers the adjustable brake feet and roller assemblies located at the bottom of the refrigerator below the freezer drawer. Before making any adjustments, remove the base grille and move the refrigerator to its final location.

Tools Needed: ¹⁄ " hex nut driver

Tools Provided: ¹⁄ " hex key wrench

1.Remove the base grille. Using both hands, grasp the grille firmly and pull it toward you. Open the freezer drawer to access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the break feet by turning them counterclockwise. The front rollers will be touching the floor.

2.Move the refrigerator to its final location.

3.Using the ¹⁄ " hex nut driver, lower the brake feet. Turn them clockwise, until the rollers are off the floor and both brake feet are snug against the floor. This keeps the refrigerator from rolling forward when opening the refrigerator doors or freezer drawer.

IMPORTANT: If you need to make further adjustments involving the brake feet, you must turn both brake feet the same amount to keep the refrigerator level.

4.Make sure the doors close easily. If you are satisfied with the door opening and closing, skip the next section and go to “Align the Doors.” If, however, the doors do not close easily or the doors pop open, adjust the tilt.

To Adjust the Cabinet Tilt:

■Open the freezer drawer. Use a ¹⁄ " hex nut driver to turn both brake feet clockwise the same amount. This will raise the front of the refrigerator. It may take several turns to allow the doors to close easier.

NOTE: Having someone push against the top of the refrigerator takes some weight off the brake feet. This makes it easier to turn them.

Style 1

¹⁄"

A

B

A.Brake foot

B.Front roller

12

Style 2

A

A.Brake foot

5.Make sure the doors are even at the top and that the space between the bottom of the refrigerator doors and the top of the freezer drawer is even. If necessary, align the doors.

To Align the Doors:

■Keeping both refrigerator doors closed, pull out the refrigerated drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin.

FILTERS AND

ACCESSORIES

Water Filtration System

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Install the Water Filter

1.Locate the accessory packet in the refrigerator and remove the water filter.

2.Take the water filter out of its packaging and remove the cover from the O-rings. Be sure the O-rings are still in place after the cover is removed.

A

B

C

D

A.Bottom hinge pin

B.Turn to the right to raise.

C.Turn to the left to lower.

D.¹⁄" Hex key wrench

■Insert the short end of the ¹⁄ " hex key wrench (packed with the Door Handle Installation Instructions) into the bottom hinge pin until it is fully engaged in the alignment screw.

To raise the door, turn the hex key to the right. To lower the door, turn the hex key to the left.

■Continue to turn the alignment screw until the doors are aligned.

6.Make sure the refrigerator is steady. If the refrigerator seems unsteady or rolls forward when a door or drawer is pulled open, adjust the brake feet.

To Steady the Refrigerator:

■Open the freezer drawer. Using a ¹⁄ " hex driver, turn both brake feet clockwise the same amount until the brake feet are snug against the floor. Check again. If not satisfied, continue to adjust the brake feet by half turns of the screw until the refrigerator does not roll forward when the drawer is opened.

NOTE: Having someone push against the top of the refrigerator takes some weight off the brake feet. This makes it easier to turn the screws.

7.Replace the base grille by aligning the ends of the grille with the leveling assemblies on each side and snapping the grille into place.

A

B

A.O-ring cover

B.O-rings

3.The water filter compartment is located in the right-hand side of the refrigerator ceiling. Push up on the compartment door to release the catch, then lower the door.

4.Align the arrow on the water filter label with the cutout notch in the filter housing and insert the filter into the housing.

13

5.Turn the filter clockwise 90 degrees (¹⁄ turn), until it locks into the housing.

NOTE: If the filter is not correctly locked into the housing, the water dispenser will not operate. Water will not flow from the dispenser.

6.While the compartment door is still open, lift the filter up into the compartment. Then, close the filter compartment door completely.

7.Flush the water system. See “Flushing the Water Filter” in the “Water and Ice Dispensers” section.

IMPORTANT: If you do not flush the water system, you may experience dripping and/or decreased flow from the water dispenser.

The Water Filter Status Light

Press OPTIONS on the control panel to launch the Options menu. Press OPTIONS, under Filter Status, again to display the percentage of filter life remaining (from 99% to 0%). Press ICE/ WATER, under Back, to return to the Normal screen.

The water filter status lights will help you know when to change your water filter.

■ORDER FILTER (yellow) - it is almost time to change the water filter. While you are dispensing water, “Order Filter” will blink seven times and sound an alert tone three times.

■REPLACE FILTER (red) - Replace the water filter. While you are dispensing water, “Replace Filter” will blink seven times and an alert tone will sound three times.

■RESET the water filter status tracking feature. After you replace the disposable filter with a new filter, closing the filter compartment door will automatically reset the filter status tracking feature. See “Using the Control(s).”

NOTE: “REPLACE FILTER” will remain illuminated if a filter is not installed or is installed incorrectly.

Replace the Water Filter

To purchase a replacement water filter, see “Accessories” in the User Guide, Use and Care Guide or User Instructions.

Replace the disposable water filter when indicated on the water filter status display or at least every 6 months. If water flow to your dispenser or ice maker decreases noticeably, change the water filter sooner.

1.Locate the water filter compartment in the right-hand side of the refrigerator ceiling. Push up to release and lower the compartment door.

2.Turn the water filter counterclockwise (to the left), and pull it straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.

3.Install the replacement water filter by following steps 2 through 7 in the “Install the Water Filter” section.

Install Air Filter

(on some models)

An air filter is 15 times more powerful than baking soda at reducing common food odors inside the refrigerator.

On some models, your refrigerator's accessory packet includes an air filter, which must be installed prior to use.

Installing the Air Filter

Install the air filter behind the vented door, located on the rear wall near the top of the refrigerator compartment.

1.Remove the air filter from its packaging.

2.Lift open the vented door.

3.Snap the filter into place.

A

A. Air filter

Installing the Filter Status Indicator

The filter comes with a status indicator, which should be activated and installed at the same time the air filter is installed.

REPLACE

MONTHS

1.Place the indicator face-down on a firm, flat surface.

2.Apply pressure to the bubble on the back of the indicator until the bubble pops to activate the indicator.

14

3.Lift open the vented air filter door. On some models, there are notches behind the door.

Models with notches:

■With the indicator screen facing outward, slide the indicator down into the notches.

NOTE: The indicator will not easily slide into the notches if the bubble has not been popped.

■Close the air filter door, and check that the indicator is visible through the window in the door.

A

B

C

A.Status indicator window

B.Air filter status indicator

C.Notches

Models without notches:

■Place the indicator somewhere it is easily visible - either inside the refrigerator, or elsewhere in your kitchen or home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, when the status indicator has completely changed from white to red.

To order a replacement air filter, contact us. See “Accessories” in the User Guide, Use and Care Guide or User Instructions for information on ordering.

1.Remove the used air filter by squeezing in on the side tabs.

2.Remove the used status indicator.

3.Install the new air filter and filter status indicator using the instructions in the previous sections.

Accessories

The following accessories are available for your refrigerator. To order an accessory, contact us and ask for the Part Number.

In the U.S.A., visit our webpage www.whirlpool.com/ accessories or call 1-800-901-2042.

In Canada, visit our webpage www.whirlpoolparts.ca or call 1-800-807-6777.

affresh® Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

affresh® Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

affresh® Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

Order Part #W10413645A or FILTER2

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver Starter kit:

Order Part #P1UB6S1

Produce Preserver Refill kit:

Order Part #P1KC6R1

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

■When the left side door is opened, the hinged seal automatically folds inward so that it is out of the way.

■When both doors are closed, the hinged seal automatically forms a seal between the two doors.

A

A. Hinged seal

Using the Controls

The controls are located above the external dispenser.

IMPORTANT: The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. Press any control button to reactivate the display screen. The home screen will appear as shown.

15

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer controls are preset at the factory.

When you first install your refrigerator, make sure that the controls are still set to the recommended set points. The factory recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.

IMPORTANT:

■Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the set points to a colder than recommended setting will not cool the compartments any faster.

■If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

■The recommended settings should be correct for normal household use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

NOTE: Areas such as a garage, basement or porch, may have higher humidity or extreme temperatures. You may need to adjust the temperature away from the recommended settings to accommodate for these conditions.

■Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.

View Temperature Set Points

1.Press and hold TEMP for 3 seconds to activate Temperature mode.

NOTE: To view temperature in degrees Celsius, press the LIGHT button, under Units, when adjust mode is activated. To return the display setting to Fahrenheit, press the LIGHT button again.

When Temperature mode is activated, press TEMP to toggle between Fridge and Freezer. The display will show the temperature set point of the selected compartment, and temperature adjusting information will appear on the display screen.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

Adjust Temperature Set Points

Refrigerator set point range: 33°F to 45°F (0°C to 7°C).

Freezer set point range: -5°F to 5°F (-21°C to -15°C).

1.When Temperature mode is activated, press TEMPERATURE to select the Refrigerator zone. The display will show the temperature set point of the selected compartment, as shown.

2.Press LOCK to raise the set point, or press OPTIONS to lower the set point.

3.When you have finished viewing (and adjusting if desired) the refrigerator set point, press TEMP, under Select Zone, to change the display to show the freezer set point. When the zone has been changed, “FREEZER” appears on the display screen.

4.Press the LOCK button to raise the set point, or press the OPTIONS button to lower the set point.

Save/Confirm Temperature Settings

■When you have finished adjusting both the refrigerator and freezer set points, press MEASURED FILL to confirm and to save the settings.

NOTE: To exit Temperature mode without saving changes, press the ICE/WATER button under Back at any time, or allow about 60 seconds of inactivity. The temperature mode will turn off automatically and return to the normal screen.

When adjusting temperature set points, use the following chart as a guide:

CONDITION:	TEMPERATURE
	ADJUSTMENT:
REFRIGERATOR too cold	REFRIGERATOR Setting
	1° higher
REFRIGERATOR too warm	REFRIGERATOR Setting
	1° lower
FREEZER too cold	FREEZER Setting
	1° higher
FREEZER too warm /	FREEZER Setting
Too little ice	1° lower

16

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is turned off.

■To turn cooling off, press and hold the LOCK and MEASURED FILL buttons at the same time for 3 seconds. The Cooling Off icon will blink seven times and then remain lit as shown.

IMPORTANT:

■To avoid unintentionally locking the dispenser or changing other settings, press both buttons at exactly the same time.

■When cooling is off, the dispenser paddles and all controls except Lock and Measured Fill are disabled.

■To manually turn off the Fast Ice feature, press the OPTIONS button to enter Options mode (unless you are already in Options mode), then press TEMP, under Fast Ice, again. When the feature has been turned off, the Fast Ice icon will disappear from the dispenser display.

Filter Status

Displays the percentage of use remaining in the water filter (from 100% remaining to 0% remaining).

To access Filter Status, press the OPTIONS button to access the Options menu, then press OPTIONS, under Filter Status, to display the percent of life remaining in the water filter.

ALSO

The water filter status lights will let you know when to change your water filter.

■ORDER FILTER (Yellow) - Order a replacement water filter.

■REPLACE FILTER (Red) - Replace the water filter. Replacing the disposable water filter will automatically reset the water filter status tracking feature. See “Water Filtration System.”

NOTE: REPLACE FILTER will remain illuminated if a filter is not installed or installed incorrectly.

A.Press LOCK and MEASURED FILL at the same time.

■Press and hold LOCK and MEASURED FILL for 3 seconds again to turn cooling back on.

Options

Press the OPTIONS button to open the Options menu and select between Fast Ice, Filter Status or Vacation mode.

Press the ICE/WATER button at any time to return to the Normal screen.

Vacation Mode

In Vacation Mode, the freezer will defrost less often to conserve energy.

■To turn on Vacation mode, press the OPTIONS button to access the Options menu, then press LOCK, under Vacation, to activate the feature. When the feature is on, the Vacation icon will appear on the dispenser display screen as shown.

■To turn off Vacation Mode, press the OPTIONS button to access the Options menu, then press LOCK to turn off the feature. The Vacation icon will disappear, and the screen will display the settings as they were before Vacation Mode was turned on.

Fast Ice

The Fast Ice feature assists with temporary periods of heavy ice use by increasing ice production.

■To turn on the Fast Ice feature, press the OPTIONS button to access the Options menu, then press TEMP, under Fast Ice to activate the feature. When the feature is on, the Fast Ice icon will appear on the dispenser display screen. The Fast Ice feature will remain on for 24 hours unless manually turned off.

NOTES:

■During the first hour after Vacation Mode is turned on, opening and closing the refrigerator door will not affect the setting. After 1 hour has passed, opening and closing the refrigerator door will turn off Vacation Mode.

■While in Vacation Mode, if Fast Ice is turned on or the Door Ajar alarm sounds, Vacation Mode will be canceled.

17

Additional Features

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the refrigerator door(s) or freezer drawer is open for 5 minutes and cooling is turned on. The alarm will repeat every 2 minutes. Close all doors and drawer to turn it off. The feature then is reset and will reactivate when either door is left open again for 5 minutes.

■NOTE: To mute the audible alarm while keeping the doors open, such as while cleaning the inside of the refrigerator, press any button on the control panel. The alarm sound will be temporarily turned off, but the Door Ajar icon will still be displayed on the dispenser control panel.

Disabling Sounds

■To turn off control and dispenser sounds, press and hold ICE/ WATER and MEASURED FILL at the same time for

3 seconds. All normal operating tones are disabled. Only alert tones will be audible.

■To turn all sounds back on, press and hold ICE/WATER and MEASURED FILL at the same time for 3 seconds again.

Showroom Mode

This mode is used only when the refrigerator is on display in a retail store. If you unintentionally turn on Showroom mode, the word “Showroom” will light up on the display. Exit Showroom mode by pressing and holding LIGHT and LOCK at the same time for 3 seconds.

Refrigerator Features

Temperature Controlled Exterior Drawer

IMPORTANT: This control sets the temperature for this drawer only.

Use the full-width drawer to store large party platters or deli trays, or use a drawer organizer to store smaller items such as yogurt, juice boxes and lunch meat for easy access.

Temperatures have been preset for the storage of: Cold Drinks, Meats/Cheeses, Assorted Items and Fruits/Vegetables. These preset temperatures cannot be adjusted.

Press SELECT to toggle through the temperature settings. The icon will illuminate when it is selected.

EasySlide Bin

A shallow storage compartment with glass lids which slide from side to side is located below and in front of the crisper drawers.

NOTE: This compartment is not temperature or humidity controlled, so it is not recommended for storing leafy vegetables.

A

B

A.Crisper drawer handles

B.EasySlide bin

To remove EasySlide bin:

1.Remove all three crisper drawers.

2.Hold the upper sliding lid near the trim and lift up to remove. Remove the lower lid.

3.Grasp the front of the bin with both hands, and lift up on the front to remove.

To replace EasySlide bin:

1.Slightly tilt the rear of the bin upward.

2.Align the center rib and tabs on the EasySlide bin with the ribs and slots in the cabinet.

3.Lower the bin into place.

Crisper Drawers

To remove and replace the drawers:

1.Grasp the handle at the bottom of the drawer and slide the drawer straight out to the stop. Lift the drawer off the bottom guide.

2.Replace the drawer by placing it on the bottom drawer guide and pushing it past the drawer stop into position.

To remove the crisper(s) cover:

1.Remove crisper drawers.

2.Holding the glass insert firmly with one hand, press up in center of glass insert until it rises above the plastic frame. Gently slide the glass insert forward to remove.

3.Lift the cover frame up and remove it.

To replace crisper(s) cover:

1.Fit back of cover frame into supports on side walls of the refrigerator and lower the front of the cover frame into place.

2.Slide rear of glass insert into cover frame and lower front into place.

3.Replace crisper drawers.

18

Water and Ice Dispensers

IMPORTANT:

■Allow 3 hours for the refrigerator to cool down and chill water.

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

■The dispensing system will not operate when either the refrigerator door or freezer drawer is open.

Flush the Water System

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water filter, flush the water system.

Flushing the water dispensing system forces air from the water line and filter and prepares the water filter for use. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1.Using a sturdy container, depress and hold the water dispenser paddle for 5 seconds.

2.Release the dispenser paddle for 5 seconds. Repeat steps 1 and 2 until water begins to flow.

3.Once water begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has been dispensed.

Calibrate Measured Fill

Household water pressure may affect the accuracy of the Measured Fill feature. So, for optimum performance of your water dispenser, you must first calibrate Measured Fill.

IMPORTANT:

■Flush the water system before calibrating Measured Fill.

■For best results, calibration should be performed when water is not being used in the house.

1.Place a sturdy measuring cup (1 cup [237 mL] size) on the dispenser tray centered in front of the ice/water dispenser paddle.

NOTE: Depending on your model, a measuring cup may be provided.

2.Press and hold the OPTIONS and LOCK buttons at the same time for 3 seconds. The words “Back” and “1 Cup” will appear on the display screen. Also, the Calibrate Measured Fill icon will illuminate and remain lit while the Measured Fill feature is being calibrated.

NOTE: You may press ICE/WATER “Back” at any time to exit calibration mode. The Calibrate Measured Fill icon will disappear.

3.Press and release the ice/water dispenser paddle, as needed, to dispense water to the 1 cup fill line.

NOTE: If overfilling or spilling occurs, discard the water and press ICE/WATER “Back” to restart the calibration process.

A

B

A.Ice/Water dispenser paddle

B.Measuring cup (1 cup)

19

4.When 1 cup of water has been correctly dispensed into the measuring cup, press the MEASURED FILL button under the word “Confirm” to confirm the calibration.

A

A.1 cup of water

5.When Measured Fill calibration has been confirmed the icons will disappear and the display will return to the home screen.

Dispensing

Press ICE/WATER to toggle through the following choices in a continuous loop:

■Water (default) - Dispenses water

■Cubed - Dispenses cubed ice.

■Crushed - Dispenses crushed ice

NOTES:

■The word “ICE” appears on the display screen when either crushed or cubed ice is selected.

■For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size.

■When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.

Water

Crushed

Cubed

The Water Dispenser

IMPORTANT:

■Dispense at least 1 qt (1 L) of water every week to maintain a fresh supply.

■If the flow of water from the dispenser decreases, it could be caused by low water pressure.

■With the water filter removed, dispense 1 cup (237 mL) of water. If 1 cup (237 mL) of water is dispensed in

8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

■If it takes longer than 8 seconds to dispense 1 cup

(237 mL) of water, the water pressure to the refrigerator is lower than recommended. See “Water Supply Requirements” and “Troubleshooting” for suggestions.

To Dispense Water (Standard):

1.Select water.

2.Press a sturdy glass against the dispenser paddle.

NOTE: While dispensing water and for 3 seconds after dispensing has stopped, the digital display will show how much water has been dispensed.

3.Remove the glass to stop dispensing.

To Dispense Water (Measured Fill):

Measured Fill allows you to dispense a specified amount of water with the touch of a few controls.

NOTE: The amount of water you select will be dispensed. Be sure that the container is empty and can hold the entire volume. If ice is in the container, you may need to adjust your selection.

1.Press MEASURED FILL to turn on the feature. When the feature is on, the Measured Fill screen appears on the display.

NOTES:

■The dispenser will automatically turn off Measured Fill after 1 minute of inactivity. When Measured Fill is turned off, any changes you have made will be lost and all defaults will be restored.

■Press ICE/WATER “Back,” to manually turn off the Measured Fill feature.

2.Press LIGHT, under Units, to toggle among ounce, cup and liter. The default unit is ounce.

Default, minimum, and maximum volumes are listed below.

Units	Default	Minimum	Maximum
Ounces	8	1	128
Cups	1	¹/	16
Liters	0.25	0.05	4.00

3.Press LOCK or OPTIONS to adjust the water volume as desired. The LOCK control increases the volume, and the OPTIONS control lowers the volume.

NOTES:

■When increasing or decreasing the dispense volumes, if an adjustment button (-/+) is held for approximately

10 seconds or longer the control may stop responding. Release the button for approximately 2 seconds and then continue making the adjustment.

■Most coffee cups (commonly 4 to 6 oz [118 to 177 mL] per cup) are not the same size as a measuring cup (8 oz [237 mL]). You may need to adjust the volume to avoid unintentionally overfilling coffee cups.

20

4.Dispense water.

NOTE: While dispensing water, the digital display will count down how much water remains to be dispensed, according to the volume you selected. The flow of water will automatically stop once the desired volume has been dispensed.

■Press a sturdy glass against the dispenser paddle.

OR

■Place the glass below the water dispenser and press MEASURED FILL, under Dispense, for hands-free dispensing.

5.To stop dispensing before the selected volume has been dispensed, remove the glass from the dispenser paddle OR press MEASURED FILL a second time.

NOTE: If you stop dispensing before the desired volume has been dispensed, the digital display will continue to show how much water remains to be dispensed. The display will turn off after 1 minute of inactivity.

■To select a new volume or start dispensing the same volume again, you must first finish dispensing the selected volume, or turn off the Measured Fill feature (either by waiting 1 minute so it will automatically turn off or by pressing ICE/WATER “Back” to manually turn it off) and then turn it back on.

The Ice Dispenser

IMPORTANT:

■If the ice cubes are hollow or have an irregular shape, it could be because of low water pressure. See “Water Supply Requirements.”

■Ice travels from the ice storage bin through the dispenser chute to the dispenser. To turn off the ice maker, see “Ice Maker and Storage Bin.”

To Clean the Ice Dispenser Chute:

Humidity causes ice to naturally clump together. Ice particles can build up until the ice dispenser chute becomes blocked.

If ice is not dispensed regularly, it may be necessary to empty the ice storage bin and clean the ice delivery chute, the ice storage bin and the area beneath the storage bin every 2 weeks.

■Remove the ice clogging the storage bin and delivery chute, using a plastic utensil if necessary.

■Clean the ice delivery chute and the bottom of the ice storage bin using a warm, damp cloth, then dry thoroughly.

To Dispense Ice:

1.Select the desired type of ice. To switch between cubed ice and crushed ice, press ICE/WATER.

WARNING

IMPORTANT: You do not need to apply a lot of pressure to the paddle to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

NOTE: Ice may continue to dispense for several seconds after removing the glass from the dispenser paddle. The dispenser may continue to make noise for a few seconds after dispensing.

The Dispenser Light

When you use the dispenser, the light will automatically turn on.

To turn on the light when you are not dispensing:

Press LIGHT to toggle through the following choices in a continuous loop:

■OFF (default) - The dispenser light is off

■ON - The dispenser light remains on at 100% brightness

■DIM - The dispenser light remains on at 50% brightness

The dispenser lights are LEDs that cannot be changed. If it appears that your dispenser lights are not working, see “Troubleshooting” for more information.

ON

DIM

The Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the controls and dispenser paddles. To turn off the ice maker, see “Ice Maker and Storage Bin.”

■Press and hold LOCK for 3 seconds to lock the dispenser.

■Press and hold LOCK a second time to unlock the dispenser. The display screen indicates when the dispenser is locked.

LOCKED UNLOCKED

Use a sturdy glass

ice.

Failure to do so can result in cuts.

2.Press a sturdy glass against the dispenser paddle. Hold the glass close to the dispenser opening so ice does not fall outside of the glass.

21

Ice Maker and Ice Storage Bin

(on some models)

IMPORTANT: To avoid low ice production and poor quality ice, flush the water system before turning on the ice maker. See “Water Dispenser.”

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 2 to 3 days for the storage bin to fill completely following installation.

■The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

■If the ice in the storage bin clumps together, break up ice using a plastic utensil and discard. Do not use anything sharp to break up the ice. This can cause damage to the ice bin and the dispenser mechanism.

■Do not store anything in the ice storage bin.

Ice Production Rate

■The ice maker should produce approximately 3 lbs (1.4 kg) of ice per day under normal operation.

■To increase ice production, select the increased ice production feature from the Options menu on the control panel. See “Using the Control(s).”

Ice Maker

The ice maker is located on the left-hand side of the refrigerator compartment ceiling. Ice cubes are ejected into the ice storage bin, located on the left-hand refrigerator door.

Turn the Ice Maker On/Off

1.Push up on the latch on the left-hand side of the ice compartment to open the door.

2.Turn on the ice maker by moving the switch to the (left) ON position.

NOTES:

■To manually turn off the ice maker, move the control to the OFF (right) position.

■Your ice maker has an automatic shutoff. The sensor will automatically stop ice production if the storage bin is full, if the door is open or the storage bin is removed. The control will remain in the ON (left) position.

A

A.Ice storage bin release latch

3.Close the ice compartment door.

Remove and Replace the Ice Storage Bin

■Remove the ice storage bin by inserting your fingers into the hole at the base of the bin and squeezing the latch to release the bin from the compartment. Lift the storage bin up and pull it straight out.

■Replace the storage bin inside the ice compartment and push down to make sure it is firmly in place.

REFRIGERATOR CARE

Cleaning

A

A. Ice compartment door latch

WARNING

Use nonflammable

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid buildup of odors. Wipe up spills immediately.

Exterior Cleaning

Please see the exterior cleaning information specific to your model.

22

1.

2.

Replace the base grille when finished. Plug in refrigerator or reconnect power.

4.

5.

Remove the base grille.

Unplug refrigerator or disconnect power.

If you need to clean the condenser: 1.

2.

3.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shutoff arm to OFF (up) position, or press the switch to OFF.

4. Empty the ice bin.

If You Choose to Turn Off the Refrigerator Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day ahead of time.

■ When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or press the switch to OFF, depending on your model.

3. Turn off the Temperature control(s). See “Using the Control(s).”

Use up any perishables and freeze other items.

If your refrigerator has an automatic ice maker, and is connected to the household water supply, turn off the water supply to the refrigerator. Property damage can occur if the water supply is not turned off.

Lights

The lights in both the refrigerator and freezer compartments are LEDs which do not need to be replaced. If the lights do not illuminate when the door or drawer is opened, call for assistance or service. In the U.S.A., call 1-800-253-1301. In Canada call

1-800-807-6777.

Vacation and Moving Care

Vacations

If You Choose to Leave the Refrigerator On While You’re Away:

Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser.

Interior Cleaning

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets.

3. Plug in refrigerator or reconnect power.

Condenser Cleaning

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

Style 1 - Smooth Door

IMPORTANT: Damage to smooth finish due to improper use of cleaning products, or using non-recommended cleaning products, is not covered under the warranty. Sharp or blunt instruments will mar the finish.

DO USE		DO NOT USE
Soft, clean cloth		Abrasive cloths
	Paper towels or newsprint
	Steel-wool pads
Warm, soapy water -		Abrasive powders or liquids
use a mild detergent		Window sprays
		Ammonia
	Acidic or vinegar based
		cleaners
		Oven cleaners
		Flammable fluids

NOTE: Paper towels scratch and may dull the clear coat of the painted door. To avoid possible damage use only soft clean clothes to polish and wipe the door.

Style 2 - Stainless Steel

IMPORTANT:

■Damage to stainless steel finish due to improper use of cleaning products, or using non-recommended cleaning products, is not covered under the warranty.

DO USE		DO NOT USE
Soft, clean cloth		Abrasive cloths
	Paper towels or newsprint
	Steel-wool pads
Warm, soapy water		Abrasive powders or liquids
		Ammonia
	Citrus-based cleaners
	Acidic or vinegar-based
		cleaners
		Oven cleaners

For heavy soil, ONLY a stainless steel cleaner designed for appliances. To order the cleaner, see “Accessories.”

Stainless steel cleaner is for stainless steel parts only! Do not allow the Stainless Steel Cleaner and Polish to come into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets.

NOTES:

■If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

■Just because a cleaner is a liquid does not mean it is nonabrasive. Many liquid cleansers formulated to be gentle on tile and smooth surfaces still damage stainless steel.

■Citric acid permanently discolors stainless steel. To avoid damaging the finish of your stainless steel refrigerator:

Do not allow these substances to remain on the finish

	Mustard		Citrus-based sauces
	Tomato juice		Citrus-based products

Marinara sauce

23

4.Clean refrigerator, wipe it, and dry well.

5.Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1.If your refrigerator has an automatic ice maker:

■Turn off the water supply to the ice maker at least one day ahead of time.

■Disconnect the water line from the back of the refrigerator.

■When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or press the switch to OFF, depending on your model.

2.Remove all food from the refrigerator and pack all frozen food in dry ice.

3.Empty the ice bin.

4.Turn off the Temperature control(s). See “Using the Control(s).”

5.Unplug refrigerator.

6.Clean, wipe, and dry thoroughly.

7.Take out all removable parts, wrap them well, and tape them together so they don’t shift and rattle during the move.

8.Depending on the model, raise the front of the refrigerator so it rolls more easily OR raise the leveling screws so they don't scrape the floor. See “Adjust the Door(s).”

9.Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the “Installation Instructions” section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

PROBLEM SOLVER

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call.

In the U.S.A., www.whirlpool.com In Canada, www.whirlpool.ca

WARNING

		Electrical Shock Hazard
		Plug into a grounded 3 prong outlet.
		Do not remove ground prong.
		Do not use an adapter.
		Do not use an extension cord.
		Failure to follow these instructions can result in death,
		fire, or electrical shock.
GENERAL OPERATION	Possible Causes and/or Recommended Solutions
Refrigerator will not operate	■ Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet.
		Do not use an extension cord.
	■ No power to the electrical outlet - Plug in a lamp to see if the outlet is working.
	■ Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the
		circuit breaker. If the problem continues, contact a licensed electrician.
	■ Control or cooling is not turned on - Turn on the refrigerator control, or turn cooling on.
		See “Using the Controls.”
	■ New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool
		completely.
		NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either
		compartment (refrigerator or freezer) more quickly.
	■ Refrigerator control is in Showroom mode (on some models)- If the refrigerator is in
		Showroom mode, cooling is turned off and “Showroom” will be illuminated on the control panel.
		See “Using the Control(s)” for more information.

24

GENERAL OPERATION	Possible Causes and/or Recommended Solutions
Motor seems to	■ Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than
run too much	you’re used to, because the compressor and fans operate at lower speeds that are more
	energy-efficient. This is normal.
	NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is added,
	the doors are opened often, or if a door has been left open.
Lights do not work	■ Your refrigerator has been equipped with LED lighting which does not need to be replaced
	- If there is power to the refrigerator and the lights do not illuminate when a door or drawer is
	opened, call for service or assistance. See either the front cover or the Warranty for contact
	information.
	■ The dispenser light is set to OFF - On some models, the dispenser light will operate only when
	the dispenser paddle is pressed. If you want the dispenser light to stay on continuously, see
	“Water and Ice Dispensers.”
	■ Doors have been open longer than 10 minutes - Close the doors and drawers to reset, and
	open to resume lighted task.
Exterior drawer control not	■ The refrigerator is in Cooling Off mode - Exit Cooling Off mode. See “Using the Control(s).”
lit/unresponsive	■ The refrigerator controls’ initialization process did not complete successfully - Unplug the
	refrigerator, wait 5 seconds. Plug in the refrigerator, and wait 30 seconds before opening the
	doors or drawers, or touching the control panel.
	■ The drawer front was recently removed - Make sure the temperature control wires have been
	properly reconnected. See “Remove and Replace Drawer Fronts.”
Refrigerator seems noisy	The compressor in your new refrigerator regulates temperature more efficiently and uses less energy
	than older models. During various stages of operation, you may hear normal operating sounds that
	are unfamiliar.
	The following noises are normal:
	■ Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the ice
	maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not
	connected to a water line, turn off the ice maker.
	■ Repetitive Clicking - Dual evaporator valve regulating the cooling operation.
	■ Cracking/Clatter - Heard when ice is ejected from the ice maker mold and then falls into the ice
	storage bin.
	■ Popping - Heard when the inside walls contract/expand, especially during initial cooldown.
	■ Hissing/Dripping - Flow of refrigerant, or flow of oil in the compressor.
	■ Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during
	normal operation.
	■ Rattling - Heard when water passes through the water line, or due to the flow of refrigerant.
	Rattling may also come from items placed on top of the refrigerator.
	■ Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into
	the drain pan.
	■ Sizzling - Heard when water drips onto the heater during the defrost cycle.
	■ Vibration - The refrigerator may not be steady. Adjust the leveling screws and lower the leveling
	foot until it is firmly against the floor. See “Refrigerator Leveling, Door Closing and Alignment.”
Temperature is too warm	■ New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool
	completely.
	NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either
	compartment (refrigerator or freezer) more quickly.
	■ Cooling is turned off - Turn on cooling. See “Using the Control(s).”
	■ Doors are opened often or not closed completely - This allows warm air to enter the
	refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are
	properly sealed.
	■ Air vents are blocked - Remove items that are immediately in front of the vents.
	■ Large amount of warm food recently added - Allow several hours for the refrigerator to return
	to its normal temperature.
	■ Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder
	setting. Check the temperature again in 24 hours.

25

GENERAL OPERATION

Possible Causes and/or Recommended Solutions

Temperature is too cold in the refrigerator/crisper

■Controls are not set correctly for the surrounding conditions - Adjust the controls to a warmer setting. Check the temperature again in 24 hours.

	■ Ice storage bin is not in the correct position - See “Ice Maker and Ice Storage Bin.”
	■ Air vents are blocked - Remove items that are immediately in front of the vents.
Temperature is too warm/	■ Control is not set correctly for the items stored in the drawer - Adjust the temperature
cold in the exterior drawer	setting. See “Temperature Controlled Exterior Drawer.”
Interior moisture buildup	NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.
	■ Room is humid - A humid environment contributes to moisture buildup. Only use the refrigerator
	in an indoor location, with as little humidity as possible.
	■ Doors are opened often or not closed completely - This allows humid air to enter the
	refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are
	properly sealed.
Frost/Ice buildup in the	■ The drawer is opened often or left open - Minimize drawer openings and close drawer
freezer compartment	completely after use.
	■ Poor drawer seal - Ensure drawer seal is making full contact with the cabinet to allow for an
	adequate seal.
	■ Temperature control(s) are not set correctly - See “Using the Control(s)” for recommended
	temperature settings.

WARNING

		Use nonflammable
		Failure to do so can result in death, explosion, or fire.
DOORS AND LEVELING	Possible Causes and/or Recommended Solutions
Doors are difficult to open	■ Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and warm
		water. Rinse and dry with a soft cloth.
Doors will not	■ Door is blocked open - Move food packages away from the door. Make sure all bins and
close completely		shelves are in their correct positions. Make sure all packaging materials have been removed.
Doors appear to be uneven	■ Doors need to be aligned, or refrigerator needs to be leveled - See “Refrigerator Leveling,
		Door Closing and Alignment.”
Refrigerator unsteady or it	■ Refrigerator brake feet are not snug against the floor - Remove the base grille. Turn both
rolls forward when opening		brake feet (one on each side) clockwise, the same amount, until they are snug against the floor.
and closing doors or		See “Refrigerator Leveling, Door Closing and Alignment.”
drawers

26

WARNING

Use a sturdy glass

ice.

Failure to do so can result in cuts.

	ICE AND WATER	Possible Causes and/or Recommended Solutions
	Ice maker is not	■ Refrigerator is not connected to a water supply, or the water supply shutoff valve is not fully
	producing ice,	turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is
	not producing	fully open.
	enough ice,	■ Kink in the water source line - A kink in the water line can reduce water flow, resulting in decreased ice
	or producing
		production, small ice cubes, and/or hollow or irregularly-shaped ice. Straighten the water line.
	small/hollow ice
		■ Ice maker is not turned on - Turn on the ice maker. See “Ice Maker and Storage Bin.”
		■ New installation - After connecting the refrigerator to a water source, flush the water system.
		(See “Water and Ice Dispensers.”) Wait 24 hours for ice production to begin. Wait 72 hours for full ice
		production. Discard the first three batches of ice produced.
		■ Refrigerator door is not closed completely - Close the door firmly. If it does not close completely, see
		“The doors will not close completely.”
		■ A water filter is installed on the refrigerator - Remove the water filter and operate the ice maker. If ice
		volume improves, then the filter may be clogged or incorrectly installed. Replace filter or install it
		correctly.
		■ Large amount of ice was recently removed - Allow sufficient time for the ice maker to produce
		more ice.
		■ Ice is jammed in the ice maker ejector arm - Remove ice from the ejector arm using a plastic utensil.
		■ Inadequate water pressure - Verify that the household has adequate water pressure. See “Water
		Supply Requirements.”
		■ Water filter is installed incorrectly - Make sure the filter is properly installed. See “Water Filtration
		System.”
		■ A reverse osmosis water filtration system is connected to your cold water supply - This can
		decrease water pressure. See “Water Supply Requirements.”
		NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.
	Ice dispenser	■ New installation - After connecting the refrigerator to a water source, flush the water system.
	will not operate	(See “Water and Ice Dispensers.”) Wait 24 hours for ice production to begin. Wait 72 hours for full ice
	properly	production. Discard the first three batches of ice produced.
		■ Ice maker is not turned on, or ice bin is not installed correctly - Turn on the ice maker and make sure
		the ice storage bin is firmly in position. See “Ice Maker and Storage Bin.”
		■ Ice is clogged or frozen together in the ice storage bin, or ice is blocking the ice delivery
		chute - Remove or separate the clogged ice, using a plastic utensil if necessary. Clean the ice delivery
		chute and the bottom of the ice storage bin using a warm damp cloth, then dry both thoroughly. To avoid
		clogging and to maintain a fresh supply of ice, empty the storage bin and clean both the storage bin and
		the delivery chute every 2 weeks.
		■ Dispenser is locked - Unlock the dispenser. See “Water and Ice Dispensers.”
		■ Ice dispenser jams while dispensing crushed ice - For models with the ice storage bin on the door,
		temporarily switch from crushed ice to cubed ice to clear the jam.
		■ Dispenser pad/lever has been pressed too long - Ice will automatically stop dispensing. Wait a few
		minutes for the dispenser to reset, then resume dispensing. Take large amounts of ice directly from the
		ice bin, not through the dispenser.
		■ Water pressure to the home is not at or above 35 psi (241 kPa) - The water pressure to the home
		affects the flow from the dispenser. See “Water Supply Requirements.”
		■ Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See “Water
		Filtration System.”

27

	ICE AND WATER	Possible Causes and/or Recommended Solutions
	Ice or water has an	■	New plumbing connections - New plumbing connections can result in off-flavored or discolored ice or
	off-taste, odor,		water. This problem should go away over time.
	or gray color	■	Ice has been stored too long - Discard the ice and wash the ice bin. Allow 24 hours for the ice maker to
			produce new ice.
		■ Odor has transferred from food - Use airtight moisture-proof packaging to store food.
		■ Use of non-recommended water supply line - Odors and tastes can transfer from certain materials
			used in non-recommended water supply lines. Use only a recommended water supply line. See “Water
			Supply Requirements.”
		■ There are minerals (such as sulfur) in the water - A water filter may need to be installed in order to
			remove the minerals.
		■ Water filter was recently installed or replaced - Gray or dark discoloration in ice or water indicates
			that the water filtration system needs additional flushing. See “Water and Ice Dispensers.”
	Water dispenser	■	Doors not closed completely - Make sure both doors are firmly closed. (On some models, only the
	will not operate		freezer door must be closed in order to operate the dispenser.)
	properly	■	Refrigerator is not connected to a water supply, or the water supply shutoff valve is not
			turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is
			fully open.
		■ Kink in the water source line - A kink in the water line can reduce water flow to the dispenser.
			Straighten the water line.
		■ Water pressure to the home is not at or above 35 psi (241 kPa) - The water pressure to the home
			affects the flow from the dispenser. See “Water Supply Requirements.”
		■ New installation - After connecting the refrigerator to a water source, flush the water system.
			See “Water and Ice Dispensers.”
		■ Water dispenser measured fill feature is not dispensing an accurate amount of water - Calibrate
			the water dispenser. See “Water and Ice Dispensers.”
		■ Dispenser is locked - Unlock the dispenser. See “Water and Ice Dispensers.”
		■ Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See “Water
			Filtration System.”
		■ A reverse osmosis water filtration system is connected to your cold water supply - This can
			decrease water pressure. See “Water Supply Requirements.”
		NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.
	Water is leaking or	NOTE: After dispensing, a few additional drops of water are normal.
	dripping from the	■	Glass was not held under the dispenser long enough - Hold the glass under the dispenser for
	dispenser
			2 to 3 seconds after releasing the dispenser pad/lever.
		■ New installation, or water filter was recently installed or replaced - Air in the water lines causes the
			water dispenser to drip. Flush the water system to remove the air in the water lines. See “Water and Ice
			Dispensers.”
		■ Residual ice in the dispenser chute is melting - Make sure the ice chute is free of ice shavings or
			pieces.
	Water is leaking	■	Water line connections are not fully tightened - Make sure all connections are firmly tightened. See
	from the back of the		“Connect Water Supply.”
	refrigerator
	Water from the	NOTE: Water from the dispenser is chilled to 50°F (10°C).
	dispenser is	■	New installation - Allow 24 hours after installation for the water supply to cool completely.
	not cool enough
			Recently dispensed a large amount of water - Allow 24 hours for the new water supply to cool
	(on some models)	■
			completely.

■ Water has not been recently dispensed - The first glass of water may not be cool. Discard the first glass of water dispensed.

■ Refrigerator is not connected to a cold water pipe - Make sure the refrigerator is connected to a cold water pipe. See “Water Supply Requirements.”

28

WATER FILTER CERTIFICATIONS

29