Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock or injury when using your fan, follow these basic precautions:
Do not use fan if any parts are damaged or missing.
Do not expose to water or rain.
Do not use this fan with any solid state speed control
device.
Never insert finger or any other objects through the grille
guard when fan is in operations.
Unplug power cord when moving from one location to
another.
Unplug power cord when removing grille for cleaning.
Be sure fan is on a stable, flat surface when in operation.
Do not use fan in window; rain and moisture may create
electrical hazard.
Do not alter the fan's assembly in any way.
Be sure front and rear grille screws are tightened before
operation.
SAVE THESE INSTRUCTIONS
ELECTRICAL REQUIREMENTS
Electrical Connection
■ To properly install your fan, plug the 2 prong power cord into
a grounded 120V outlet.
■ This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug is
intended to fit in a polarized outlet only one way.
Fused Plug and Cord Information
WARNING
Electrical Shock Hazard and Fire Hazard
Always unplug this product before installing or
replacing fuses.
Do not operate any fan with a damaged cord or plug.
Discard fan or return to an authorized service facility
for examination and/or repair.
Do not run cord under carpeting.
Do not cover cord with throw rugs, runners, or similar
coverings.
Do not route cord under furniture or appliances.
Arrange cord away from traffic area and where it will
not be tripped over.
Failure to follow these instructions could result in
shock or fire hazard.
NOTES:
■ This product employs overload protection (fuse). A blown
fuse indicates an overloaded or short-circuit situation. If the
fuse blows, unplug the product from the outlet. Replace the
fuse as per the user servicing instructions below (follow the
product marking for proper fuse rating) and check the
product. If the replacement fuse blows, a short circuit may be
present and the product should be discarded or returned to
an authorized service facility for examination and/or repair.
If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
■ This fan is rated at 120 VAC, 60 Hz, 45 W.
■ If your fan loses power and you suspect that the fuse on your
fan has blown, replace the fuse. See the following steps for
replacing the fuse.
1. Disconnect power by unplugging the fan. Grasp the plug and
remove from the receptacle or other outlet device.
NOTE: Do not unplug by pulling on the cord.
2. Slide open the fuse door on the side of the plug. Be sure the
fuse door is open completely and the blown fuse is fully
visible.
A
placeholder
A. Fuse
B. Fuse door
3. Remove the blown fuse.
4. Snap the 5-amp, 125-volt replacement fuse into place.
5. Fully close the fuse door by sliding back into place.
6. Discard the blown fuse.
7. The fan should now be ready for normal use.
IMPORTANT: Risk of fire. Do not replace attachment plug.
Contains a safety device (fuse, AFCI, SCDI) that should not be
removed. Discard product if the attachment plug is damaged.
Failure to follow these instructions can result in death or fire.
B
3
Speed Controls
POWER
0.5
FAN OPERATING INSTRUCTIONS
Power and Settings
1. Press the power button to turn on the fan.
2. The fan is preset to 3-fan operation when turned on the first
time.
■ Press FAN 1 time to select upper and lower fan operation.
■ Press FAN 2 times to select middle and lower fan
operation.
■ Press FAN 3 times to return to 3-fan operation.
operation.
automatically.
■ Press 1 time for 0.5 hour (30 minutes).
■ Press again to add 30 minutes.
■ Continue pressing for up to 7.5 hours.
-
TIMER
1
SPEED
2
+
TURBO
OSC
4
3. Press the Speed “-” or “+” button to adjust the fan speed.
4. Press TURBO to select the highest fan speed with 3-fan
5. Press OSC to turn on or off oscillation.
6. Press TIMER to set the length of time before the fan turns off
7. Press OSC to turn on oscillation.
FAN
TIMER
OSC
TURBO
Remote Control
Install/Replace Batteries
1. With the buttons of the remote control facing down, remove
the screw from the battery door.
2. Depress the battery door latch and remove.
3. Install/replace 2 AAA batteries.
4. Replace battery door.
A. Battery door latch
B. Screw
B
A
4
FAN CARE
Cleaning
■ Use a soft, damp cloth to clean all surfaces. Wipe dry with a
soft, dry cloth.
■ Do not use a cleaning solution that is damaging to paints or
plastics.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
In the U.S.A. and Canada
Call the Customer Service Center toll free: 1-866-990-7365.
Our consultants provide assistance with:
■ Features and specifications on our full line of appliances.
■ Referrals to local dealers, repair parts distributors and service
companies. Designated service technicians are trained to
fulfill the product warranty and provide after-warranty service,
anywhere in the United States and Canada.
■ Do not bend the blades.
■ The motor bearings are permanently sealed and do not
require additional lubrication.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
To locate the designated service company in your area, you
can also look in your telephone directory Yellow Pages.
For further assistance
If you need further assistance, you can write to Master Brands
HK Limited with any questions or concerns at:
Master Brands HK Limited
c/o CCRG Teleservices
4240 Ridge Lea Road, Suite 29
Amherst, NY 14226
Please include a daytime phone number in your correspondence.
5
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.