30105536aGB.fm Page 17 Thursday, December 30, 2004 10:53 AM
CONTENTS
BEFORE USING THE WASHING MACHINE
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE DOOR
CHILD SAFETY (IF AVAILABLE) BEFORE THE FIRST WASH CYCLE PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES REMOVING THE FILTER DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER SALES SERVICE TRANSPORT / HANDLING ELECTRICAL CONNECTION
Black process 45.0° 100.0 LPI
30105536aGB.fm Page 18 Thursday, December 30, 2004 10:53 AM
BEFORE USING THE WASHING MACHINE
1.Removing the packaging and inspection
•After unpacking, make sure that the washing machine is undamaged. If in doubt, do not use the washing machine. Contact After-Sales Service or your local retailer
•Check that the accessories and supplied parts are all present
•Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of children, as they are potentially dangerous
2.Remove the transport bolts
•The washing machine is fitted with transport bolts to avoid any possible damage to the interior during transport. Before using the machine, it is imperative that the transport bolts are removed
3.Install the washing machine
•Remove the protective film from the control panel
•Move the appliance without lifting it by the worktop
•Install the appliance on a solid and level floor surface, preferably in a corner of the room
•Make sure that all four feet are stable and resting on the floor and then check that the washing machine is perfectly level (use a spirit level).
4.Water inlet
•Connect the water supply inlet hose in accordance with the regulations of your local water company
• Water inlet: |
Cold water only |
• Water tap: |
3/4” threaded hose |
|
connector |
• Water pressure |
|
(flow pressure): |
100-1000 kPa (1-10 bar). |
5.Drain
•Connect the drain hose to the siphon or hook it over the edge of a sink by means of the “U” bend supplied
•If the washing machine is connected to an integrated drainage system, ensure the latter is equipped with a vent to avoid simultaneous loading and draining of water (siphoning effect)
6.Electrical connection
•Electrical connections must be carried out by a qualified technician in compliance with the manufacturer's instructions and current standard safety regulations
•Data regarding voltage, power consumption and protection requirements is given on the inside of the door.
•The appliance must be connected to the mains by means of a socket with an earth connection in accordance with current regulations. The washing machine must be earthed by law. The manufacturer declines all liability for damage to property or injury to persons or animals due to non-compliance with the directions given above
•Do not use extension leads or multiple sockets
•Before any maintenance on the washing machine disconnect it from the mains supply
•After installation, access to the mains plug or to disconnection from mains supply must be ensured at all times via a double-pole switch
•Do not operate the washing machine if it has been damaged during transport. Inform the After-Sales Service
•Mains cable replacement is only to be carried out by After-Sales Service
•The appliance must only be used in the household for the prescribed uses
Minimum housing dimensions:
Width: |
600 mm |
Height: |
825 mm |
Depth: |
600 mm |
18
Black process 45.0° 100.0 LPI
30105536aGB.fm Page 19 Thursday, December 30, 2004 10:53 AM
PRECAUTIONS AND GENERAL RECOMMENDATIONS
1.Packaging
•The packaging material is entirely recyclable, and
marked with the recycling symbol . Adhere to current local regulations when disposing of
packaging material
2.Disposing of packaging and scrapping old washing machines
•The washing machine is built from reusable materials. It must be disposed of in compliance with current local waste disposal regulations
•Before scrapping, remove all detergent residues and cut off the power cable so that the washing machine is made unusable
3.General recommendations
•Do not leave the appliance plugged in when not in use
•Turn off the tap
•Before any cleaning and maintenance switch off the machine or disconnect it from the mains
•Clean the outside of the washing machine with a damp cloth. Do not use abrasive detergents
•Never open the door forcibly or use it as a step
•Children must not be allowed to play with the washing machine or to climb into the drum (see also the following page chapter “Child Safety”)
•If necessary, the power cable may be replaced with an identical one obtained from our AfterSales Service. The power cable must only be replaced by a qualified technician
4.EC Declaration of Conformity
•The appliance conforms to the following European Standards:
Low voltage directive 73/23/EEC 89/336/EEC Electromagnetic Compatibility
Directive
93/68/EC CE Marking Directive.
19
Black process 45.0° 100.0 LPI
30105536aGB.fm Page 20 Thursday, December 30, 2004 10:53 AM
DESCRIPTION OF THE WASHING MACHINE
1. |
Worktop |
1 |
|
2. |
Control panel |
|
|
2 |
|
||
3. |
Detergent dispenser |
|
|
3 |
|
||
4. |
Service plate |
|
|
4 |
|
||
|
(inside the door) |
|
|
|
|
||
5. |
Door |
5 |
|
6. |
Child safety device (if provided, |
|
|
|
inside the door) |
|
|
7. |
Filter (behind cover) |
|
|
8. |
Plinth |
6 |
|
9. |
Adjustable feet |
|
|
|
|
7 |
|
|
|
8 |
|
|
|
9 |
|
|
|
|
|
DOOR
To open the door, hold the door handle, press the inside handle and pull the door. Close the door by pressing it without excessive force until it clicks shut.
CHILD SAFETY (IF AVAILABLE)
To protect the appliance against improper use, turn the plastic screw on the interior of the door. To do this, use the thick rounded corner of the coloured insert from the detergent dispenser or a coin:
•Slot vertical: the door will not lock
•Slot horizontal - normal position: the door can be locked again
BEFORE THE FIRST WASH CYCLE
To remove any residual water used in testing by the manufacturer, we recommend that you carry out a short wash cycle without laundry.
1.Open the tap.
2.Close the door.
3.Pour a little detergent (about 30 ml) into the detergent compartment .
4.Select and start a short programme (see quick reference guide).
20
Black process 45.0° 100.0 LPI