Whirlpool Duet WFW9200SQA11, Duet WFW9200SQA12, Duet WFW9200SQ10, Duet WFW9300VU02, Duet WFW9200SQ02 Use & Care Manual

...

0 (0)

FRONT.LOADING

AUTOMATICWASHER

For questions about features, operation/performance,

parts, accessories or service call: 1-800-253-1301

In Canada, call: 1-800-807-6777

www.whirlpooLcom or www.whirlpool.ca

AUTOMATICADECARGA

Si tiene preguntas respecto a las caracterfsticas, funcionamiento,

rendimiento, pares, accesorios o servicio tecnico, Ilame al:

www.whirlpool.com o www.whirlpool.ca

or visit our website at

IAVADOIbi.

FRONTAL

1-800-253-1301

En Canad& Ilame al: 1-800-807-6777

o visite nuestro sitio web en

461970235711

¢8183011

LAVEUSE

AUTOMATIQUEA

CHARGEMENTFRONTAL

Au Canada, pour assistance, installation ou service, composez le :

Table of Contents/lndice/Table des matieres ....... 2

1-800-807-6777

ou visitez notre site internet h

www.whirlpool.ca

Designed to use only HE High Efficiency Detergent

Disefiada para utilizar

solamente detergente de

alto rendimiento

Con£ue pour I'utilisation

d'un detergent haute efficacite seulement

TABLEOFCONTENTS

WASHER SAFETY .......................................................................... 3

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Options ......................................................................................... 4

Location Requirements ................................................................ 5

Drain System ................................................................................ 6

Electrical Requirements ............................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 7

Remove Transport System .......................................................... 7

Connect the Inlet Hoses ............................................................... 8

Route the Drain Hose ................................................................... 8

Secure the Drain Hose ................................................................. 9

Level the Washer .......................................................................... 9

Complete Installation ................................................................... 9

FEATURES AND BENEFITS ........................................................ 10

WASHER USE............................................................................... 11

Starting Your Washer ................................................................. 11

Using the Proper Detergent ....................................................... 11

Using the Dispenser ................................................................... 12

Pausing or Restarting ................................................................. 13

Changing Cycles, Options and Modifiers .................................. 13

Status Lights .............................................................................. 13

Cycles ......................................................................................... 14

Normal Washer Sounds ............................................................. 15

Options ....................................................................................... 16

Modifiers ..................................................................................... 16

Laundry Guide ............................................................................ 17

LAUNDRY TIPS ............................................................................ 18

Loading ....................................................................................... 18

WASHER CARE ............................................................................ 19

Cleaning Your Washer ............................................................... 19

Water Inlet Hoses ....................................................................... 20

Vacation, Storage, and Moving Care ......................................... 20

TROUBLESHOOTING .................................................................. 21

ASSISTANCE OR SERVICE ......................................................... 24

WARRANTY .................................................................................. 25

INDICE

SEGURIDAD DE LA LAVADORA ................................................. 26

REQUISITOS DE INSTALACION ................................................. 27

Piezas y herramientas ................................................................ 27

Opciones .................................................................................... 27

Requisitos de ubicaci6n ............................................................. 28

Sistema de desag(Je .................................................................. 29

Requisitos electricos .................................................................. 30

INSTRUCCIONES DE INSTALACION ......................................... 30

Eliminaci6n del sistema protector de transporte ....................... 30

Conexi6n de las mangueras de entrada .................................... 31

Tendido de la manguera de desagOe ........................................ 31

Fijacidn de la manguera de desag(]e ......................................... 32

Nivelaci6n de la lavadora ........................................................... 32

Complete la instalaci6n .............................................................. 32

CARACTERISTICAS Y BENEFICIOS .......................................... 33

USO DE LA LAVADORA ............................................................... 34

Puesta en marcha de la lavadora .............................................. 34

Uso del detergente adecuado ................................................... 34

Uso del dep6sito ........................................................................ 35

Pausa o reanudaci6n de la marcha ........................................... 36

Cambio de ciclos, opciones y modificadores ........................... 36

Luces de estado ......................................................................... 37

Ciclos .......................................................................................... 38

Sonidos normales de la lavadora ............................................... 39

Opciones .................................................................................... 40

Modificadores ............................................................................. 40

Guia para el lavado ..................................................................... 41

CONSEJOS DE LAVANDER|A ..................................................... 41

C6mo cargar ............................................................................... 42

CUIDADO DE LA LAVADORA ..................................................... 42

C6mo limpiar su lavadora .......................................................... 42

Mangueras de entrada de agua ................................................. 43

Cuidado para las vacaciones, el almacenaje o en case de

mudanza ..................................................................................... 43

SOLUCION DE PROBLEMAS ...................................................... 44

AYUDA O SERVICIO TECNICO ................................................... 47

GARANTiA .................................................................................... 48

TABLEDESMATIERES

SECURIT¢: DE LA LAVEUSE ........................................................ 49

EXIGENCES D'INSTALLATION ................................................... 50

Outillage et pieces ...................................................................... 50

Options ....................................................................................... 50

Exigences d'emplacement ......................................................... 51

Systeme de vidange ................................................................... 52

Specifications electriques .......................................................... 53

INSTRUCTIONS D'INSTALLATION ............................................. 53

elimination des accessoires de transport .................................. 53

Raccordement des tuyaux d'alimentation ................................. 54

Acheminement du tuyau de vidange ......................................... 54

Immobilisation du tuyau de vidange .......................................... 55

Reglage de I'aplomb de la laveuse ............................................ 55

Achever I'installation .................................................................. 55

CARACTI:!:RISTIQUES ET AVANTAGES ..................................... 56

UTILISATION DE LA LAVEUSE ................................................... 57

Mise en marche de la laveuse .................................................... 57

Utilisation du detergent approprie ............................................. 57

Utilisation du distributeur ........................................................... 58

Pause ou remise en marche ....................................................... 59

Changement des programmes, options et modificateurs .........60

Temoins lumineux ...................................................................... 60

Programmes ............................................................................... 61

Sons normaux emis par la laveuse ............................................ 62

Options ....................................................................................... 63

Modificateurs .............................................................................. 63

Guide de lessivage ..................................................................... 64

CONSEILS DE LESSIVAGE .......................................................... 64

Chargement ................................................................................ 65

ENTRETIEN BE LA LAVEUSE ..................................................... 65

Nettoyage de la laveuse ............................................................. 65

Tuyaux d'arrivee d'eau ............................................................... 66

Precautions h prendre avant les vacances, un entreposage

ou un demenagement ................................................................ 66

DEPANNAGE ................................................................................. 67

ASSISTANCE OU SERVICE ......................................................... 70

GARANTI E .................................................................................... 71

IODO Le QUE I_AGINA

WASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer follow basic precautions,

including the following:

m Read all instructions before using the washer. mDo not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

mDo not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

mUnder certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during this time.

SAVE THESE INSTRUCTIONS

_,Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

_,Before the washer is removed from service or discarded,

remove the door or lid.

_,Do not reach into the washer if the drum, tub or agitator is

moving.

_,Do not install or store the washer where it will be exposed to

the weather.

_,Do not tamper with controls. _,Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and have the skills to carry out.

_,See "Electrical Requirements" for grounding instructions.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation. The parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses

• Pliers (that open to 1%6" [39.5 mm])

• Flashlight (optional) Tools needed for installation

• Open end wrenches 17 mm and 13 mm

• Level

• Wood block

• Ruler or measuring tape

Parts supplied:

A B

A. Drain hose form B. Inlet hose (2)

C. Inlet hose washer (4)

Alternate Parts

Your installation may require additional parts. Ifyou are interested in purchasing one of the items listed here, call the toll-free

number on the cover or in the "Assistance or Service" section.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already standpipe taller available) than 96" (2.4 m)

Overhead sewer Standard 20 gal. (76 L), 30" (76.2 cm) tall

drain tub or utility sink and sump pump (available from local plumbing suppliers)

Floor drain Siphon break, Part Number 285834;

additional drain hose Part Number 8318155; and connector kit,

Part Number 285835

D. Transport bolt hole plug (4)

E. Beaded strap

i ............................

Pedestal

You have the option of purchasing pedestals of different heights separately for this washer. You may select a 10" (25.4 cm) or a

15.5" (39.4 cm) pedestal. These pedestals will add to the total height of the washer for a total height of approximately 48" (121.9 cm) or 53.5" (135.9 cm).

A. 10" (25.4 cm) pedestal B. 15.5" (39.4 cm) pedestal

To order, call the dealer from whom you purchased your washer or refer to the "Assistance or Service" section of this manual.

Pedestal Color Part Number

Height

10" (25.4 cm) White WHP1000SQ

15.5" (39.4 cm) White WHP1500SQ

Stack Kit

Are you planning to stack your washer and dryer? To do so you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8541503.

Drain hose too 4 ft (1.2 m) drain hose extension kit, short Part Number 285863

Water faucets 2 longer water fill hoses: beyond reach of fill 6 ft (1.8 m) Part Number 76314, hoses 10 ft (3.0 m) Part Number 350008

Selectingtheproperlocationforyourwasherimproves performanceandminimizesnoiseandpossiblewasher"walk."

Yourwashercanbeinstalledunderacustomcounter,orina basement,laundryroom,closet,orrecessedarea.See"Drain System."

Companionappliancelocationrequirementsshouldalsobe considered.Properinstallationisyourresponsibility.

Youwillneed

• Awaterheatersettodeliver120°F(49°C)watertothe washer.

• Agroundedelectricaloutletlocatedwithin6ft(1.8m)of wherethepowercordisattachedtothebackofthewasher. See"ElectricalRequirements."

• Hotandcoldwaterfaucetslocatedwithin4ft(1.2m)ofthe hotandcoldwaterfillvalves,andwaterpressureof 20-100psi(137.9-689.6kPa).

Alevelfloorwithamaximumslopeof1"(2.5cm)under entirewasher.Installingthewasheronsoftfloorsurfaces, suchascarpetsorsurfaceswithfoambacking,isnot

recommended.

• Asturdyandsolidfloortosupportthewasherwithatotal weight(waterandload)of400Ibs(180kg).

Donotoperateyourwasherintemperaturesbelow32°F(0°C). Somewatercanremaininthewasherandcancausedamagein lowtemperatures.

Installation clearances

• The location must be large enough to allow the washer door to be fully opened.

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door, and floor moldings.

• Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce noise transfer.

• Companion appliance spacing should also be considered.

Washer Dimensions

Recommended installation spacing for custom undercounter installation

The dimensions shown are for the recommended spacing. Custom undercounter installation - Washer only

39" rnin=

(99=0cm)

1" _ 97"--_t<- 1"

(2,5cm) (68.5cm) (2.5cm)

Recommended installation spacing for recessed or closet installation, with or without a pedestal

The dimensions shown are for the recommended spacing. Recessed area or closet installation

_f 3"

48 in,2. _ _ -

(3!0 cm 2)

24 im2 * = __

(155crn2)

I1"I_-31w'-_14"1<-

(2.5 cm} (80 cm) (10.2 era)

A B

A. Side view - closet or confined area B. Closet door with vents

*Min, top and bottom air openings for closet door.

Recessed or closet installation - Washer on pedestal

I_ (45.7crn)

(7.6cm)

18"rain._

1"--_ _--!"

(2,5cm) (2.5era)(68.6cm)

A. Recessed area B. Side view - closet or confined area

(2.5cm) (80 cm) (!0.2 cm)

I1"I<-31W'91 4"1

Recommended installation spacing for recessed or closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in? *

(310 ¢rn2)

3" (7.6crn)

3" (7.6 cm)

24in2*

(155cm2)

1" (2.5crn)

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See

"Tools and Parts."

Standpipe drain system - wall or floor (views A & B) The standpipe drain requires a minimum diameter standpipe of

2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L)per minute.

The top of the standpipe must be at least 30" (76.2 cm) high and no higher than 96" (2.4 m) from the bottom of the washer.

76"

(193ore)

5_"**

(!4 ¢m)

*Min. top and bottom air openings for closet door.

**External exhaust elbow requires additional space.

***Wall, door and floor molding may require additional spacing.

Recommended installation spacing for cabinet installation

The dimensions shown are for the recommended spacing. For cabinet installation, with a door, the minimum ventilation

openings in the top are required.

" • ) 7" (I7,8 cm)

25cm

8.6ore)E (2.5crn)

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 30" (76.2 cm) above the floor.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See "Tools and Parts."

The siphon break must be a minimum of 28" (71 om) from the bottom of the washer. Additional hoses might be needed.

4 31Y2 I

(lO.2crn) (80,Ocm) (2,5cm) (2.5crn)(68.6crn) (2.5cm)

1 I

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS

EmectricatShockHazard

Plugintoagrounded3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Faimureto follow these }nstructions can resumt }n death,

fire, or emectr}cal shock.

A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.

This washer is equipped with a power supply cord having a 3 prong ground plug.

To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, ground-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

For a grounded, cord-connected washer: This washer must be grounded. In the event of a malfunction or breakdown, grounding wilI reduce the risk of electrical shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified eIectrician or serviceman if you are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet instaIled by a qualified

electrician. For a permanently connected washer:

This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on

the appliance.

INSTALLATIONINSTRUCTIONS

IMPORTANT: Position the washer so that the rear of the washer is within approximately 3 ft (90 cm) of its final location.

There are 4 bolts in the rear panel of the washer that support the suspension system during transportation. These bolts also retain the power cord inside the washer until the bolts are removed.

1. Using a 13 mm wrench, loosen each of the bolts.

2. Oncetheboltisloose,moveittothecenteroftheholeand completelypulloutthebolt,includingtheplasticspacer coveringthebolt.

3. Onceall4boltsareremoveddiscardboltandspacers.Then pullthepowercordthroughtheopeningoftherearpaneland closetheholewiththeattachedcap.

4. Closetheboltholeswiththe4transportboltholeplugs.

NOTE:Ifthewasheristobetransportedatalaterdate,callyour localservicecenter.Toavoidsuspensionandstructuraldamage toyourwasher,itmustbeproperlysetupforrelocationbya

certifiedtechnician.

6. Usingpliers,tightenthecouplingswithanadditional two-thirdsturn.

NOTE: Do not overtighten. Damage to the coupling can result.

Turn on the water faucets and check for leaks. NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

Makesurethewasherdrumisempty.

1. AttachthehosewiththeredcolorindicatortotheHot(left) inletvalve.Attachingtheredcouplingfirstmakesiteasierto

tightenconnectionwithpliers.Screwoncouplingbyhand untilitisseatedonthewasher.

2. AttachthehosewiththebluecolorindicatortotheCold (right)waterinletvalve.Screwoncouplingbyhanduntilitis

seatedonthewasher.

9 r ¸_

t4.Hot water inlet C.Cold water inlet

Using pliers, check the tightness of the hose couplings already attached to the washer.

NOTE: Do not overtighten. Damage to the coupling can result.

4. Attach the hose with the red color indicator to the hot water faucet. Screw on coupling by hand until it is seated on the

washer.

5. Attach the hose with the blue color indicator to the cold water faucet. Screw on coupling by hand until it is seated on the

washer.

Proper routing of the drain hose protects your floors from damage due to water leakage. Read and follow these

instructions.

Remove drain hose from washer cabinet

Gently pull the corrugated drain hose from the shipping clips.

Laundry tub drain or standpipe drain

Connect the drain hose form to the corrugated drain hose.

A. Snap either end of the drain hose form to the drain hose at

the point where the corrugation begins.

B. Bend drain hose over drain hose form and snap into place.

To keep drain water from going back into the washer:

• Do not straighten the drain hose, and do not force excess drain hose into standpipe. Hose should be secure, but loose enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. See Floor drain under "Tools and Parts."

Drape the power cord over the washer top.

Secure the drain hose to the laundry tub leg or standpipe with the beaded strap provided. (See illustrations A and B.)

If the washer faucets and the drain standpipe are recessed (see illustration C), put the hooked end of the drain hose in the standpipe. Tightly wrap the beaded strap around the

water inlet hoses and the drain hose.

Do not force excess drain hose into the standpipe.

Properly leveling your washer avoids excessive noise and vibration.

1. Check the levelness of the washer by placing a level on the top edge of the washer, first side to side, then front to back.

If the washer is against a wall, move the washer out slightly before tipping back. If the washer is not level, first prop the front with a wood block and adjust the feet as necessary; then prop the back and adjust feet as necessary. Repeat this step until washer is level.

Make sure all four feet are stable and resting on the floor. Then check that the appliance is perfectly level (use a level).

After the washer is level, use a 17 mm open-end wrench to turn the nuts on the feet tightly against the washer cabinet.

IMPORTANT: All four feet must be tightened. If the nuts are not tight against the washer cabinet, the washer may vibrate.

4. The washer should not move front to back, side to side, or diagonally when pushed on its top edges.

5. Slide the washer to its final location.

6. Confirm the levelness of the washer.

1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See "Electrical Requirements."

2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Check that the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

Electrical Shock Hazard Pmuginto a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can resumt in death,

fire, or electdcam shock.

Plug into a grounded 3 prong outlet.

Read "Washer Use."

Totest and to clean your washer, measure 1/2the detergent manufacturer's recommended amount of HE High Efficiency detergent for a medium-size load. Pour the detergent into the detergent dispenser. Select NORMAL/CASUAL, and then select START.Allow the washer to complete one whole cycle.

Use only HE High Efficiency detergent.

FEATURESANDBENEFITS

Electronic Controls Flexible electronic controls are easy to use whether you are a

beginner or an expert.

Smart Dispensers The Smart Dispensers make your washer truly automatic. This

washer provides a three-compartment dispenser which includes separate compartments for main wash detergent, fabric softener, and bleach. The dispenser has large pour zones. The dispenser is self-cleaning, and can be easily removed. Laundry products are diluted with fresh water and added to the load at the proper time in the wash cycle.

Auto Water Level This washer automatically adjusts water level for best cleaning

and rinsing performance. Two sensors determine load size, load composition, and suds level, then the sensors adjust the water level to the proper setting. This eliminates guesswork. The water level is just right for every wash load size.

Larger Load Size Since there is no agitator, you can wash larger, bulkier items such

as a king-sized bedspread. You are also able to wash more clothes at one time, which means fewer loads.

Stainless Steel Drum The stainless steel drum eliminates corrosion and enables higher

spin speeds for more water extraction, helping to reduce drying time.

High-Efficiency Wash System Your new front-loading, high-efficiency washer saves time with

fewer, larger loads. It also lowers your water and energy bills by helping conserve resources.

Spin Speeds This washer automatically selects the spin speed based on the

cycle selected. This factory setting can be changed, however. This washer offers up to five different spin speed choices.

Heating Element This washer has a heating element that automatically heats the

water to the best temperature on select cycles. This enables stepped cleaning, a process in which warm water is brought in and mixed with detergent first, then the water is heated. Stepped cleaning starts the wash cycle with warm water to remove stains (such as blood and grass). The water continues to be heated in order to remove stains such as perspiration.

6th Sense TM Technology Intuitive intelligence "knows every load" determining load sizes,

water levels and how much cleaning time is needed.

sense ._

Add A Garment When this option is available at the beginning of the cycle, the

Add a garment Status Light will glow for the first 8 minutes. This washer allows an 8-minute period in which other garments may

be added to a load.

Direct Injection Wash System This washer channels 100% of the water through the dispensers

to assure thorough rinse-out and mixture of all the laundry products before they touch any garments. The water is then sprayed from the top front onto the center of the load, providing even distribution and optimum cleaning performance. Itis normal for small amounts of water to remain in the dispensers when the wash cycle is complete.

Efficient Detergent System with Anti-Escape Valve This washer has a specially designed valve that closes during the

wash portion of the cycle so that 100% of the water and detergent mixture is used on the load. The Efficient Detergent System ensures that no water or detergent is wasted.

6-Point Suspension System Shock absorbers, 2 springs and electronic controls are specially

designed to help redistribute the load automatically and minimize movement of the wash drum during the spin cycle. The 6-Point Suspension System reduces the amount of force transmitted to the floor by the washer, resulting in reduced noise and vibration.

WASHERUSE

NORMAL

HAND DELl

Contro[ Lo kiU!_leck

14_ldf_r3 Se_nds

CLEANW,4_HER

NOTE: The panel shown above may be different from that of your model.

BULKY iTEMS S_AR? _timatedlime Remaining ExtraRinse

SOAK

D0orLocke

Before washing clothes for the first time, if not completed during the final installation step, choose the Normal/Casual cycle and run it without clothes. Use only HE High Efficiency detergent. Use

_/2the manufacturer's recommended amount for a medium-sized load. This initial cycle serves to ensure the interior is clean before

washing clothes.

DelayWash

_ _upel Hot " High

Warm Low _ Non'lal Soft

L Cok! NIpSpi_ I.igllt Off

@@®

W_terremp Si soil cycle

AllC01d Speed Leve_ _ign_l

;_as_s

First Wash Cycle Without Laundry

But/on Sound

Fire Hazard

Never place items in the washer that are dampened with gasoline or other fmammabmefmuids.

No washer can completemy remove oil Do not dry anything that has ever had any type of oH on

it (including cooking oils). Doing so can resumt in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance. The following is a guide to using your washer. Please refer to

specific sections of this manual for more detailed information. Do not store laundry products on the top surface of this washer.

Vibration is normal during operation.

:::{

Use only High Efficiency detergents. The package for this type of detergent will be marked "HE" or "High Efficiency." This wash

system, along with less water, will create too much sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer cycle times and reduced rinsing performance. It may also result in component failures and

noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance. Follow the manufacturer's instructions to determine the amount of detergent

to use.

For All Wash Cycles

Open the washer door by pulling on the handle. Sort laundry according to color and type of fabric. Place a load of sorted clothes in the washer. Do not overload washer. Overloading can cause poor cleaning.

• The washer can be fully loaded, but not tightly packed. Washer door should close easily.

• Mix large and small items and avoid washing single items. Load evenly.

• Wash small items, such as infant socks, in mesh garment bags. It is recommended that more than one garment bag be used, and that each garment bag be filled with equal

amounts of material.

• When unloading garments, check under the gray rubber seal at the front of the tub for small items.

Close the washer door by pushing it firmly until the lock clicks. The washer door will remain locked during the wash cycle.

NOTES:

• After any wash cycle is completed, the door must be opened and then closed before a new cycle can begin.

• The door can be opened only if PAUSE/CANCEL is selected while the Add A Garment light is glowing or if the cycle has been canceled.

• See "To cancel a cycle" in "Changing, Cycles, Options and Modifiers" section.

3. Open the dispenser drawer and add laundry products to the detergent, bleach, or fabric softener compartments. Close drawer slowly to avoid spills. See "Using the Dispenser."

Use only HE High Efficiency detergent.

4. Turn on the washer by selecting POWER. Select one of the cycles by turning the cycle selector. The indicator light for the selected cycle will glow green. When selecting a wash cycle, the preset options and modifiers (such as Water Temp, Spin Speed, and Soil Level) for the selected cycle will glow green. Selectable options will glow amber. If an option or modifier is unavailable with a selected cycle, the light will not illuminate. The display shows the estimated time remaining. The preset settings provide the recommended fabric care for the selected cycle. See "Cycles."

5. Select the desired Options. Not all options are available with all cycles. See "Options."

6. Select the desired modifiers such as Water Temp, Spin Speed and Soil Level. Not all modifiers are available with all cycles and options. See "Modifiers."

7. If desired, select the CYCLE SIGNAL. The signal is helpful when you are washing items that should be removed from the washer as soon as it stops. Select Loud, Soft or Off.

8. If desired, select the BU]q-ON SOUND. This feature makes a sound each time a button is pressed. Select Loud, Soft or Off.

9. Select and hold START for approximately 1 second.

• If you do not select START within 5 minutes of choosing a

cycle, the washer automatically shuts off.

• When the wash cycle is complete, the DONE status light

glows, the door unlocks, and the wash load can be removed from the washer. The washer powers down automatically 60 minutes after the cycle is complete and the DONE light goes off. To power down the washer manually after the wash cycle is complete, select PAUSE/

CANCEL once.

10. To use the same cycle again, press POWER first, then select START.

11. To begin the wash cycle later Select DELAY WASH until the desired delay time (in hours)

shows in the Estimated Time Remaining display. Select START. The countdown to the wash cycle will show in the display window.

IMPORTANT: When delaying a cycle, use only powdered detergents in the main wash compartment since liquid detergents may seep out of the compartment during Delay Wash, before the wash cycle begins.

Choosing the Right Detergent

Use only High Efficiency detergents. The package for this type of detergent will be marked "HE" or "High Efficiency." This wash system, along with less water, will create too much sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer cycle times and reduced rinsing performance. It may also result in component failures and noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance. Follow the

manufacturer's instructions to determine the amount of detergent to use.

Use only HE High Efficiency detergent.

To fill dispenser compartments

1. Pull out the dispenser drawer.

2. Add the desired laundry product to the proper compartment.

3. Push in the dispenser drawer slowly and completely (to avoid a spill).

Your new washer has a dispenser drawer with three separate compartments for your laundry products--one is for detergent, one is for liquid chlorine bleach, and one is for liquid fabric softener. Laundry products are diluted and dispensed automatically at the proper time during the wash cycle, making it unnecessary for you to return to the washer during the cycle to

add them. It is normal for small amounts of water to remain in the

dispensers when the wash cycle is complete. Do not put laundry products directly into the wash tub. Always

use the proper dispensers when adding laundry products.

Dispenser

A. Detergent type selector B. Main Wash detergent compartment C. Dispenser release lever D. Chlorine bleach compartment

E.Fabric softener compartment

Main Wash detergent compartment

(Letter B in Dispenser Illustration) Add liquid or powdered HE detergent to this compartment for

your main wash cycle. The detergent type selector (B) must always be in the correct position for the detergent type used.

IMPORTANT: If you are using the Delay Wash option, powdered detergent must be used in the Main Wash compartment, since

liquid detergents may seep out of the Main Wash compartment before the main wash begins.

• Do not fill beyond the "MAX" level. Use the detergent manufacturer's recommended amount for load size.

Liquid or powdered color-safe bleach may be added to the Main Wash compartment along with the same type of

detergent, liquid or powdered.

Liquid detergent:

1. To pause the washer at any time, press PAUSE/CANCEL.

2. To continue the cycle, press START (for approximately 1 second).

Not all Options and Modifiers are available with all cycles. Available modifiers will glow amber. If an option or modifier is

unavailable with a selected cycle, the light will not illuminate. Cycles, Options and Modifiers can be changed anytime before

START is selected. Options and Modifiers can be changed anytime after START is

selected and before the start of the selected Option or Modifier.

Selector in position for liquid detergent

A. Detergent type selector

Powdered detergent:

Selector in position for powdered detergent

A. Detergent type selector

Chlorine bleach compartment (Letter D in Dispenser Illustration)

Add no more than 2/3cup (160 mL) liquid chlorine bleach to this compartment. The bleach will be automatically diluted and dispensed at the optimum time during the first rinse after the wash cycle. This compartment cannot dilute powdered bleach.

• Always measure liquid chlorine bleach. Use a measuring cup with a pour spout; do not guess.

• Do not fill beyond the "MAX" level. Overfilling could cause garment damage.

Fabric softener compartment

(Letter E in Dispenser Illustration) Pour measured liquid fabric softener into the fabric softener

dispenser, if desired. IMPORTANT: Dilute all fabric softener with water for a total of 1/4cup (60 mL).

• Do not overfill. The dispenser holds 1/4cup (60 mL).

• Do not spill or drip any fabric softener onto the clothes.

NOTES:

• Use only liquid fabric softener in this dispenser.

• Do not use fabric softener dispensing balls in this washer. Dispensing balls will not operate correctly with this washer.

To cancel a cycle and select a new cycle

1. Press PAUSE/CANCEL twice.

2. Press POWER.

3. Select desired cycle.

4. Select the desired Options or modifiers such as Water Temp, Spin Speed and Soil Level.

5. Press START (for approximately 1 second) to restart the washer at the beginning of the new cycle.

To cancel a cycle

1. Press PAUSE/CANCEL twice.

2. The washer powers down, the door unlocks, and clothes can be removed.

NOTE: If the water level or the temperature is too high, the washer will drain automatically before the door unlocks.

To change Options or Modifiers after the cycle has started

1. Press PAUSE/CANCEL once.

2. Select the desired Options or modifiers such as Water Temp, Spin Speed and Soil Level. Available selections will glow

amber.

3. Press START (for approximately 1 second) to continue the cycle.

To drain the washer manually

1. Press PAUSE/CANCEL twice.

2. Press POWER.

3. Select DRAIN/SPIN.

4. Press START (for approximately 1 second) to begin the drain.

5. When the spin is complete, the door unlocks. Items can be removed from the washer.

_ill

These lights show which portion of the cycle the washer is operating. They also indicate when you can add an additional item to the wash cycle and when the controls are locked.

EstmatedTimeRe_r)_ing

Add a garment

This washer allows an 8-minute period in which other garments may be added to the load. You can add items to the washer if the Add a garment status light is glowing.

To add items when Add a garment light is glowing

1. Select PAUSE/CANCEL once. The washer door unlocks, and items can be added.

2. To continue the cycle, close the door and select and hold START (for approximately 1 second).

To add items when the Add a garment light is not glowing

1. Select PAUSE/CANCEL twice. This will cancel the wash cycle and options. The washer door unlocks, and items can be

added.

2. Close the door, press POWER and select the new cycle and options. Select and hold START (for approximately 1 second).

Done

The Done Status Light stays on for 60 minutes after the cycle is complete, and then the washer shuts off.

Controls Lock/Unlock

The Controls Lock avoids unintended use of the washer. You can also use the control lock feature to avoid unintended cycle or

option changes during a cycle. When Controls Lock is lit, all buttons are disabled except for Pause/Cancel and Start. You can lock the controls while the washer is operating.

To lock the controls

Press and hold CONTROLS LOCK/UNLOCK for 3 seconds.

ControlsLocldU_lack

The status light next to the CONTROLS LOCK/UNLOCK button will glow.

To unlock the controls

Press and hold CONTROLS LOCK/UNLOCK for 3 seconds until the status light turns off.

NOTE: To lock or unlock the controls when the washer is off, press and hold CONTROLS LOCK/UNLOCK for 3 seconds.

Door Locked

When the status light glows, the door is locked.

Estimated time remaining

The cycle time varies automatically based on your water pressure, water temperature, detergent and clothes load. The cycle time will be extended if oversudsing occurs or the load is

unbalanced. The SUDs routine removes extra suds and assures proper rinsing of your garments. During the unbalance routine the

time displayed may pause until this activity is complete, then resume with the cycle. These routines may add up to a half-hour to the default cycle time.

Cycles can be selected by turning the Cycle Control knob to the desired cycle. Each cycle is designed for different types of fabric and soil levels. The modifier indicator lights, on the right-hand side of the panel, will change as cycles are selected.

I/O[{MAL

DELICA]E 3ULKYITEMS

HAND HEAVYDUTY WASHABLE'

_HITES

SANITARY

Each cycle has a preset Soil Level (estimated cycle time), Water Temperature and Spin Speed, and may have preset options. The preset settings provide the recommended fabric

care for the selected cycle. The preset settings will glow green to show the preselected

options and modifiers, and be changed anytime before START is pressed. Not all options and modifiers are available with all

cycles. Available selections glow amber. (To change settings after the cycle has started, press PAUSE/CANCEL once, then

select the desired settings. Press START to continue the cycle.)

Powdered detergents may not dissolve well in a slow-speed cycle. For best results, use liquid detergent in slow-speed

cycles.

Preset cycle settings

Each cycle has a preset Soil Level (cycle time), Water Temperature, and Spin Speed. The preset settings provide the

recommended fabric care for the selected cycle. See chart.

Cycle Soil Level Water Temp Spin Speed

(cycle time)

Sanitary Normal Super Hot/Cold High

(1:50)

Whitest Normal Hot/Cold High Whites (1:15)

Heavy Duty Normal Hot/Cold High

(1:05)

Bulky Items Normal Warm/Cold Low

(0:55)

Normal/ Normal Warm/Cold High Casual (0:50)

Delicate Normal Warm/Cold Medium

(0:40)

Hand Normal Cold/Cold Low

Washables (0:30)

Clean N/A High

Washer

Soak Normal Warm/Cold No Spin

(0:30)

Rinse/Spin Normal Cold/Cold High

(o:2o)

Drain/Spin Normal N/A High

(0:11)

Tochangethepreset cycle settings

Press the selector of each available setting until the desired setting glows green.

Sanitary

Use this cycle to clean heavily soiled, colorfast fabrics. This cycle combines a super hot water temperature and fast speed tumbling to help ensure the removal of heavy soils and stains. It is recommended that you set your hot water heater to 120°F (49°C) to ensure proper performance during this cycle. Extra high speed spin helps shorten drying time.

Whitest Whites

This cycle is especially designed for cleaning loads of soiled white fabrics with the addition of bleach. Hot washing temperatures assure optimal bleach activity. An additional rinse

provides optimal rinse performance to avoid chlorine residues on your laundry. This cycle combines fast-speed tumbling, longer

wash time, and extra high speed spin to shorten drying time.

Hand Washables

Use this cycle to clean hand washable and special-care garments. Similar to the way garments are hand washed in a sink, the wash action of this cycle combines periods of low speed tumbling and soaking. CRADLE CLEAW Mmotion offers gentle fabric care for effective cleaning of delicate and hand washable garments. Low speed spin reduces wrinkling.

Clean Washer

Use the Clean Washer cycle once a month to keep the inside of your washer fresh and clean. This cycle uses a higher water level in combination with liquid chlorine bleach to thoroughly clean the

inside of your washing machine. See "Cleaning Your Washer." IMPORTANT: Do not place garments or other items in the washer

during the Clean Washer cycle. Use this cycle with an empty wash drum.

Soak

Heavy Duty

Use this cycle to wash loads of sturdy, colorfast fabrics and heavily soiled garments. This cycle combines fast-speed tumbling, longer wash time, and extra high speed spin to shorten drying times. Ifthe water temperature is lower than needed for this cycle, the heater will warm the water to the optimum temperature.

Bulky Items

Use this cycle to wash large items such as blankets and comforters. This cycle starts with a soak to thoroughly saturate your large load. This is followed by medium wash action and low- speed spin only to maintain load balance.

Normal/Casual

Use this cycle to wash loads of no-iron fabrics, such as sport shirts, blouses, casual business clothes, permanent press blends, cottons and linens, and synthetic fabrics. This cycle combines medium-speed tumbling, high-speed spin, and a load cooling process to reduce wrinkling.

NOTE: For the best energy performance, use the Normal/Casual Cycle.

Delicate

Use the Soak cycle to help remove small spots of set-in stains on fabrics. This cycle provides a soak time with warm or cold water followed by drain. Extra water, a short tumbling phase for equal

distribution of the laundry, and a soaking time without drum movement improve the removal of set-in stains. Drain without

spin assures gentle treatment, even for delicate articles.

Rinse/Spin

Use this cycle to get a rinse and spin only. This cycle combines fast-speed tumbling and extra high speed spin. Ifdesired, you can reduce the spin speed by selecting the speed you want from

the SPIN SPEED modifier.

A Rinse/Spin cycle is useful for

• Loadsthat need rinsing only.

• Adding fabric softener to a load.

Drain/Spin

Use this cycle to drain your washer or to drain and spin your wash load. The spin speed is preset to extra high. If desired, you can reduce the spin speed by selecting the speed you want from

the SPIN SPEED modifier. NOTE: Loads of synthetics, delicate fabrics, hand washables,

and woolens should be drained with no spin or low spin speed to avoid fabric stress.

Use this cycle to clean hand washable and special-care garments. Similar to the way garments are hand washed in a sink, the wash action of this cycle combines periods of low speed tumbling and soaking. CRADLE CLEAN TM motion offers gentle fabric care for effective cleaning of delicate and hand washable garments. Low speed spin reduces wrinkling.

• Use mesh garment bags to wash undergarments such as underwire bras, items with strings, and small items such as

infant socks.

As with any new product, you will hear sounds that you are not accustomed to. You may hear various sounds when the door is

locked and unlocked, and during the washing, rinsing, and spinning process. Between changes in wash actions, there will

be momentary pauses. You will hear water spraying and splashing during the wash and rinse cycles. These new sounds

and pauses are part of normal washer operation.

You can customize your wash by adding options to your cycle selections. You can add or change an option after starting a cycle anytime before the selected option begins. Not all options are available with all cycles. Available options will glow amber. Current selections will glow green. If an option is unavailable with a selected cycle, the light will not illuminate.

E×lra Rinse

[)elayWash

Cyde _uttos

Signal Sound

See the "Laundry Guide" for an overview of possible options for each Wash Cycle selection.

You can select more than one option for a cycle. Some options cannot be added to some cycles. If an option is unavailable with a selected cycle, there will be 3 short tones, and the light for that option will not glow when selected.

Preset cycle settings of Water Temperature, Spin Speed, and Soil Level can be changed. You can change a modifier after starting a cycle anytime before the selected modifier begins. Not all modifiers are available with all cycles and options. Available options will glow amber. Current selections will glow green. If a modifier is unavailable with a selected cycle, the light will not

illuminate. NOTE: The panel shown below may be different from that of your

model.

Super Hot " Flig_

Hot ;;_ Mediurr _4eay Wars ;; Low /10final

( Cold NoSpir' ght

@®®

Water_errrl SOn S0il

All¢_ld 5Deed Level

Rinses

• To change the water temperature, select the WATER TEMP button until the desired setting glows green.

• To change the spin speed, select the SPIN SPEED button until the desired setting glows green.

• To change cycle time, select SOIL LEVEL button until the desired setting glows green.

Delay Wash

Use this to begin the wash cycle later.

• Select DELAY WASH until the desired time (in hours) shows in the Estimated Time Remaining display.

• Select START. The countdown to the wash cycle will show in the display window.

When delaying a cycle, use only powdered detergents in the main wash compartment since liquid detergents may seep out of the compartment during Delay Wash, before the wash cycle begins.

Extra Rinse

An extra rinse can be used to aid in the removal of detergent or bleach residue from garments. This option provides an additional rinse with the same water temperature as the first rinse.

Cycle Signal

This signal is helpful when you are removing items from the washer as soon as it stops. Press CYCLE SIGNAL to select Loud,

Soft or Off.

Button Sound

Button sounds are used to notify you of what has been selected or to let you know when something is not available. Press

BUTTON SOUND to select Loud, Soft or Off.

Wash/Rinse Temp

Select a water temperature based on the type of load you are washing. Use the warmest wash water safe for fabrics. Follow garment label instructions.

In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve well. Soils may be difficult to remove.

6TH SENSE TM Technology

The 6TH SENSE TM Technology control electronically senses and maintains a uniform water temperature. 6TH SENSE TM Technology control regulates incoming hot and cold water. 6TH SENSE TM Technology control is automatically turned on when a cycle is selected. See "Preset Cycle Settings" in "Cycles." 6TH SENSE TM Technology control ensures consistent cleaning.

• 6TH SENSE TM Technology control works for all wash temperature settings.

sense"

Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these wash cycles.

CYCLE SUGGESTED LOAD TYPE AVAILABLE OPTIONS

Delay Wash Extra Rinse

Sanitary Heavily soiled underwear, towels, work clothes, diapers, etc. v' v'

Whitest Whites Soiled white fabrics v' v'

Heavy Duty Sturdy, colorfast fabrics and heavily soiled garments, v' v' Bulky Items Normally soiled blankets and comforters v' v' Normal/Casual Normally soiled blouses, shirts, overalls, etc., made of polyester, v' v'

nylon, cotton, linen, or cotton blends Delicate Special-care items marked "Hand Washable" v' v' Hand Washables Special-care items marked "Hand Washable" v' i/

Clean Washer No clothes v' Soak Fabrics made of cotton, linen, polyester or nylon v'

Rinse/Spin Fabrics made of cotton, linen, polyester or nylon v' i/ Drain/Spin Fabrics made of cotton, linen, polyester or nylon v'

LAUNDRYTIPS

Preparing clothes for washing

Follow these recommendations to help you prolong the life of your garments.

• Use only High Efficiency detergents, The package for this type of detergent will be marked "HE" or "High Efficiency." This wash system, along with less water, will create too much sudsing with a regular non-HE detergent. Using regular detergent will likely result in washer errors, longer cycle times and reduced rinsing performance, It may also result in component failures and noticeable mold or mildew. HE detergents are made to produce the right amount of suds for the best performance, Follow the manufacturer's instructions to determine the amount of detergent to use.

Use only HE High Efficiency detergent.

Close zippers, snaps, and hooks to avoid snagging other items. Remove pins, buckles, and other hard objects to avoid

scratching the washer interior. Remove non-washable trim and ornaments.

Empty pockets and turn them inside-out. Turn down cuffs; brush away lint and dirt. Turn synthetic knits inside-out to avoid pilling.

Tie strings and sashes so they will not tangle. Mend tears, loose hems, and seams.

Treat spots and stains. Stained or wet garments should be washed promptly for best

results. Mix large and small items, avoid washing single items, and

load evenly. Wash small items, such as infant socks, in a mesh garment

bag. To create a balanced load it is recommended that more than one garment bag be used, and that each garment bag

be filled with equal amounts of material. NOTE: If you are washing only small items, it is

recommended that more than one mesh garment bag be used, and that each garment bag be filled with equal

amounts of material,

Sorting

• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together. Separate lint-givers (towels, chenille) from lint-takers (corduroy, synthetics, permanent press), When possible, turn lint-givers inside-out.

• Separate dark colors from light colors, colorfast items from noncolorfast items.

• Sort by fabric and construction (sturdy cottons, knits, delicate items).

Unloading

• Remove clothes from washer after the cycle is completed. Metal objects such as zippers, snaps, and buckles may rust if left in the washer basket for a long time.

• When unloading garments, occasionally check under the gray colored seal at the front of the tub for small items.

Loading suggestions Heavy Work Clothes

4 jeans 2 sweatpants 4 workpants 2 sweatshirts

4 workshirts

Towels 10 bath towels

10 hand towels

Mixed Load

3 sheets (1 king, 2 twin) 9 T-shirts 4 pillowcases 9 shorts

3 shirts 10 handkerchiefs 3 blouses

14 washcloths

WASHERCARE

The Washer Maintenance procedure should be performed on a monthly basis.

3. Open the dispenser drawer and immediately add ¾ cup

Cleaning the Door Seal

1. Open the washer door and remove any clothing or items from the washer.

2. Inspect the gray colored seal between the door opening and the basket for stained areas. Pull back the seal to inspect all areas under the seal and to check for foreign objects.

A. Seal

3. If stained areas are found, wipe down these areas of the seal, using the procedure that follows.

a} Mix a dilute solution, using ¾ cup (177 mL) of liquid

chlorine bleach, and 1 gal. (3.8 L) of warm tap water.

b} Wipe the seal area with the dilute solution, using a damp

cloth.

c} Let stand 5 minutes. d} Wipe down area thoroughly with a dry cloth and let the

washer interior air dry with door open.

IMPORTANT:

• Wear rubber gloves when cleaning for prolonged periods.

• Refer to the bleach manufacturer's instructions for proper

use.

Washer Maintenance Procedure

This washer has a special cycle that uses higher water volumes in combination with liquid chlorine bleach to thoroughly clean the

inside of the washer.

NOTES:

• Read these instructions completely before beginning the cleaning process.

If necessary, the cleaning cycle may be interrupted by pressing the Pause/Cancel button. This will stop the cycle. A Rinse/Spin cycle must then be run to thoroughly rinse the remaining bleach from the washer. Failure to do so will cause damage to the washer and clothing added to the next cycle.

Begin procedure

1. Open the washer door and remove any clothing or items from the washer.

2. Close the washer door.

(160 mL) of liquid chlorine bleach to the bleach compartment. NOTE: Do not add any detergent to this cycle. Use of more

than ¾ cup (160 mL) of bleach will cause product damage over time.

4. Be sure the dispenser drawer is closed.

5. Select the CLEAN WASHER cycle.

6. Press START. NOTE: The basket will rotate, then the door will unlock, lock

again, and then the cycle will continue.

• The machine will not fill, but the basket will rotate while

The cycle will determine whether clothing or other items are in the washer.

8. Once the cycle has begun, allow the cycle to complete.

9. After the cycle is complete, leave the door open slightly, to allow for better ventilation and drying of washer interior.

Always do the following to maintain washer freshness

• Useonly HEHigh Efficiency detergent.

Leave the door slightly open after each cycle to allow for better ventilation and drying of washer interior.

Repeat the cleaning procedure monthly, using ¾ cup (160 mL) of liquid chlorine bleach.

If the procedure does not sufficiently improve the machine freshness, please evaluate your installation and usage

conditions for other causes.

Cleaning the exterior

Use a soft damp cloth or sponge to wipe up any spills. Occasionally wipe the outside of your washer to keep it looking new. Use mild soap and water. Do not use abrasive products.

Cleaning the dispenser drawer

The dispenser drawer is removable for easy cleaning.

1. Unlock the dispenser drawer by pressing the Release Lever in the Main Wash detergent compartment. See "Using the Dispenser." Remove the drawer.

2. Remove the inserts (the siphon from the softener and bleach compartments and the detergent selector).

3. Wash the parts under running water.

4. Replace the inserts and return the dispenser to the drawer.

the washer runs a short sensing cycle. This will take approximately 3 minutes.

If no items are detected in the washer, it will proceed to Step 8.

If any items are detected in the washer, all the Cycle lights will flash, "rL" or "F-34" will be displayed, and the WASH and CONTROLS LOCKED lights will remain lit.

The door will unlock.

• Press PAUSE/CANCEL to cancel the failure code. Then repeat steps 1,2 and 6 to start the cycle

again.

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear or leaks are found.

When replacing your inlet hoses, record the date of replacement.

Install and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can damage your washer. If storing or moving your washer during freezing weather,

winterize it.

Non-use or vacation care:

Operate your washer only when you are at home. If you will be on vacation or not using your washer for an extended period of time,

you should:

• Unplug washer or disconnect power.

• Turn off the water supply to the washer. This helps avoid unintended flooding (due to awater pressure surge) while you are away.

• Slightly open door to provide ventilation.

To winterize washer:

1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.

2. Run washer on a Drain/Spin cycle.

3. Unplug washer or disconnect power.

4. Shut off both water faucets.

5. Disconnect water inlet hoses from faucets and drain.

To use washer again:

1. Flush water pipes. Reconnect water inlet hoses to faucets. Turn on both water faucets.

To transport the washer:

1. If washer will be moved during freezing weather, put in 1 qt (1 L) of R.V.-type antifreeze in the drum. Run washer on a Drain/Spin cycle.

2. Unplug the power cord.

3. Disconnect the drain hose from the drain system and attach to rear panel clips.

4. Shut off both water faucets.

5. Disconnect the water inlet hoses from faucets, then drain the hoses and clip them to the rear panel of the washer.

IMPORTANT: Call for service. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid suspension and structural damage to your washer, it must be properly set up for relocation by a certified technician.

Reinstalling the washer

1. Follow the "Installation Instructions" to locate, level and connect the washer.

2. Run the washer through the Normal/Casual cycle with 1/2the manufacturer's recommended amount of HE detergent for a medium-size load, to clean the washer and remove the antifreeze, if used.

Emectricat Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter,

Do not use an extension cord. Faimureto follow these instructions can result in death,

fire, or emectrical shock.

Plug in washer or reconnect power.

Run the washer through the Normal/Casual cycle with 1/2the manufacturer's recommended amount of HE detergent for a

medium-size load, to clean the washer and remove the antifreeze, if used.

TROUBLESHOOTING

Firsttry the solutions suggested here to possibly avoid the cost of a service call...

Washer displaying code message and tone sounds

"F20" (Water Inlet Problem--no water or insufficient

water supply)

Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.

Check the following: Are water faucets completely turned on?

Are screens at inlet hose connection to washer clogged? Are water inlet hoses kinked?

Are water inlet hoses frozen? Plug in washer or reconnect power. Re-select cycle and press

START. If the problem remains, call for service.

• "F21"(Drain Problem) Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.

Check the following: Is the drain hose kinked?

Is the drain hose frozen? Is the drain hose clogged?

Is the drain hose more than 96" (2.4 m) above the floor? Plug in washer or reconnect power. Re-select cycle and press

START. If the problem remains, call for service. "SUD" (Suds Routine)

When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. "SUD" is displayed during rinsing and at the end of the cycle to inform you that Suds Routine was activated. Use only HE (High Efficiency) detergents.

• "F22" (Front door lock) Select PAUSE/CANCELtwice to cancel the cycle.

Check the following: Is the washer door firmly shut? The door must be completely closed for the washer to operate. The door may look closed, but may not be latched. Open the door and close firmly.

Were you washing a large load? Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to tumble freely. An overloaded basket may keep the door from shutting completely. Reduce your load size if needed.

Press POWER and select START.

• "F" codes other than F2O, F21 or F22 Select PAUSE/CANCEL twice to cancel the cycle. Select

DRAIN/SPIN if there is excessive water in the washer. Re-select cycle and press START. Ifthe problem remains, call

for service.

Washer won't start

E_ectrical Shock Hazard

P_ug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

• Check the following: Is the power cord plugged into a grounded 3 prong outlet?

Is the washer door firmly closed? Has a cycle been selected, but START has not been selected

and held for 1 second? Was the door open after completion of last cycle?

Washer won't fill, wash or rinse

• Check the following: Is the power cord plugged into a grounded 3 prong outlet?

Is there power at the plug? Check electrical source or call an electrician.

Are the hot and cold water faucets turned on? Is the water inlet hose kinked?

Are the water inlet valve screens clogged? Turn off the water and remove inlet hoses from the washer.

Remove any accumulated film or particles. Reinstall hoses, turn water on and check for leaks.

Washer stops

• Checkthe following: Is the power cord plugged into a grounded 3 prong outlet?

Is there power at the plug? Check electrical source or call an electrician.

Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. Ifthe problem

continues, call an electrician. Are you using an extension cord?

Do not use an extension cord.

Washer won't drain or spin

Washer odor

• Is the drain hose clogged, or the end of the drain hose more than 96" (2.4 m) above the floor?

• Is your voltage low? Check electrical source or call electrician. Do not use an

extension cord.

• Is the "SUD" routine active? Cycle will complete once extra suds are removed.

• Is the load balanced? A single or bulky item may cause imbalance. Add more items

or redistribute the load.

Washer makes noise or vibrates

Is the washer level? The washer must be level. The four feet should be properly

installed, and the nuts should be tightened against the washer cabinet.

Is the washer gurgling or humming? As water is drained from the washer, you may hear air being

pulled through the pump. This happens during the end of draining. It is normal.

Are you washing items with metal snaps, buckles or zippers?

You may hear metal items touching the washer drum. This is normal.

Is washer installed on a sturdy and solid floor? Refer to the "Installation Instructions" for flooring •

requirements. Noise and vibration may be reduced by placing a piece of 3_,,(19.1 mm) plywood underneath your washer.

The plywood may extend underneath both washer and dryer • to keep them at equal heights.

Washer leaks

• Check household plumbing for leaks.

Dispensers clogged or leaking

Are the laundry products in the correct dispenser compartment?

Add the correct amounts of detergent, fabric softener or liquid chlorine bleach to the correct compartments. Add •

powdered or liquid color-safe bleach to the Main Wash compartment. Be sure to match powdered color-safe bleach with powdered detergent or match liquid color-safe bleach • with liquid detergent.

Is the detergent type selector in the correct position? Selector should be in the lower position when using liquid detergent and in the upper position when using powdered detergent.

See "Cleaning Your Washer."

Are you using HE detergent?

Use of non-HE detergent can cause a film residue which can result in odor.

Did you leave the door open after use? This washer has a tight seal to avoid water leaks. To avoid odors, leave the door open to allow the washer to dry

between uses.

Load too wet

• Did you use the right cycle for the load being washed? Select a cycle with a higher spin speed.

Did you wash a single item or bulky items or have you overloaded the washer?

A single item, bulky items, or overloading may cause imbalance. Add items or try to evenly distribute your wet

laundry in the drum, and start a DRAIN/SPIN cycle. If the laundry is still wet, take half of the load out of the washer and

try again.

Residue or lint on load

• Did you add detergent to the dispenser? For best results, add detergent to the detergent

compartment. Do not add detergent to the washer drum.

Did you sort properly?

Sort lint givers (towels, chenille) from lint takers (corduroy, synthetics). Also sort by color.

Did you overload the washer? Do not overload the washer. The washer can be fully loaded, but not tightly packed. The wash load must be balanced. Lint can be trapped in the load if overloaded.

Check the following: Was paper or tissue left in pockets?

Did you use enough HE detergent? Use enough detergent to remove lint and hold it in suspension. Use only HE detergent. Follow the

manufacturer's instructions to determine the amount of detergent to use.

Is your water colder than 60°F (15.6°C)? Wash water colder than 60°F (15.6°C) may not completely dissolve the detergent.

Are you using a low-speed wash cycle?

Powdered detergents may not dissolve well in a slow-speed cycle. For best results, use liquid detergent for slow-speed cycles such as Delicate and Hand Washables.

+ 50 hidden pages