Welltech ATA-171P, ATA-171, ATA-172 V 1.6 Manual

Download

Page 1

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

ATA-171/172/17

(ATA-S1/S2/P)

User’s Guide

V.1.6

2006/10/27

Page 2

ATA-171/172/171P (ATA-S1/S2/P)

1 Introduction....................................................................................................................................... 2

1.1 Hardware Overview...............................................................................................................2

1.2 Software Overview ................................................................................................................2

2 Keypad Interface for The ATA........................................................................................................... 3

3 Setup the ATA by Web Browser........................................................................................................ 4

3.1 Login......................................................................................................................................4

3.2 System Information for the ATA.............................................................................................5

3.3 Phone Book...........................................................................................................................5

3.4 Phone Setting........................................................................................................................6

3.5 Network ...............................................................................................................................13

3.6 IP Settings ...........................................................................................................................18

3.7 NAT Trans. ..........................................................................................................................25

3.8 Others..................................................................................................................................26

3.9 System Auth. .......................................................................................................................31

3.10 Save Change ......................................................................................................................34

3.11 Update.................................................................................................................................35

3.12 Reboot.................................................................................................................................37

4 Setup the ATA by using Console (Hyper Terminal)......................................................................... 38

4.1 Configure the COM port ......................................................................................................38

4.2 Login into the ATA ...............................................................................................................39

4.3 Using CLI command to configure the ATA ..........................................................................40

5 How to make a phone call .............................................................................................................. 46

User’s Guide

Page 3

ATA-171/172/171P (ATA-S1/S2/P)

1 Introduction

This user’s manual is for 1-port FXS VoIP terminal adapter (ATA). This user’s manual will explain the IVR instruction, web configuration, and command line configuration for the ATA. Before using the ATA, some setup processes are required to make the ATA work properly. Please refer to the Setup Menu for further information.

1.1 Hardware Overview

The ATA has the following interfaces for Networking, telephone interface, LED indication, and power connector.

1.1.1 Two RJ-45 Networking interface, these two interfaces support 10/100Mps Fast Ethernet. you can connect one RJ-45 Fast Ethernet port to the ADSL or Switch, and connect the other one to your computer.

1.1.2 One RJ-11 Type analog telephone jack interfaces. You can connect one analog telephone to the terminal adapter.

1.1.3 LED Indication: There are three LED indicators in the ATA to show the Power, Register, and Off-Hook indication.

1.2 Software Overview

Network Protocol Tone

User’s Guide

• SIP v1 (RFC2543), v2 (RFC3261)

• IP/TCP/UDP/RTP/RTCP

• IP/ICMP/ARP/RARP/SNTP

• TFTP Client/DHCP Client/ PPPoE Client

• Telnet/HTTP Server

• DNS Client

• NAT/DHCP Server

Codec

• G.711: 64k bit/s (PCM)

• G.726: 16k / 24k / 32k / 40k bit/s (ADPCM)

• G.729A: 8k bit/s (CS-ACELP)

• G.729B: adds VAD & CNG to G.729

Voice Quality

• VAD: Voice activity detection

• CNG: Comfortable noise generator

• LEC: Line echo canceller

• Packet Loss Compensation

• Adaptive Jitter Buffer

Call Function

• Call Hold

• Call Waiting

• Call Forward

• Caller ID

• 3-way conference

DTMF Function

• In-Band DTMF

• Out-of Band DTMF

• SIP Info

SIP Server

• Registrar Server (three SIP account)

• Outbound Proxy

• Ring Tone

• Ring Back Tone

• Dial Tone

• Busy Tone

• Programming Tone

Phone Function

• Volume Adjustment

• Speed dial key

• Phone book

• Flash

IP Assignment

• Static IP

• DHCP

• PPPoE

Security

• HTTP 1.1 basic/digest authentication for Web setup

• MD5 for SIP authentication (RFC2069/ RFC 2617)

QoS

• ToS field

NAT Traversal

• STUN

Configuration

• Web Browser

• Console/Telnet

• IVR/Keypad

Firmware Upgrade

• TFTP

• Console

• HTTP

Page 4

ATA-171/172/171P (ATA-S1/S2/P)

2 Keypad Interface for The ATA

You can use the PSTN phone keypad to operate the ATA. Please follow the instruction to configure

your terminal adapter.

Group IVR Action IVR Menu Choice Parameter(s) Notes:

Funcrion

Function

Function Reboot

Function Factory Reset

Info

Info Check IP Type

Info

Setting Set DHCP client

Setting

Setting Set Codec

Setting

Dial out from

PSTN Line

Unlock keypad

setting

Check WAN IP

Address

Check LAN IP

Address

Check the Phone

Number

Check Network

Mask

Check Gateway

IP Address

Check Primary

DNS Server

Setting

Check Firmware

Version

Set Static IP

Address

Set Network

Mask

Set Gateway IP

Address

Set Primary DNS

Server

Set Handset

Gain

Set Handset

Volume

0＊＊＊＊

#190#

#195#

#198#

#126#

#120#

#121#

#122#

#123#

#124#

#125#

#128#

#111#

#112xxx*xxx*xxx*xxx#

#113xxx*xxx*xxx*xxx#

#114xxx*xxx*xxx*xxx#

#115xxx*xxx*xxx*xxx#

#130+[1-8]#

#131+[00~15]#

#132+[00~12]#

None

Enter IP address using numbers on the telephone keypad. Use the * (star) key when entering a decimal point. Enter value-using numbers on the telephone keypad. Use the * (star) key when entering a decimal point. Enter IP address using numbers on the telephone keypad. Use the * (star) key when entering a decimal point. Enter IP address using numbers on the telephone keypad. Use the * (star) key when entering a decimal point. 1:G.711 u-Law, 2: G.711 a-Law, 4: G.729a, 5: G.726 16K, 6: G.726 24K, 7: G.726 32K, 8: G.726 40K,

Handset Gain from 0~15

Handset Volume from 0~12

Press O# can pass relay to PSTN Line, user can dial out from PSTN Line. (For 171P only) After you unlock keypad setting, then you may configure the ATA. After you hear “Option Successful,” hang-up. The system will reboot automatically. System will automatically Reboot. WARNING: ALL “User-Changeable” NONDEFAULT SETTINGS WILL BE LOST! This will include network and service provider data. IVR will announce the current WAN IP address of the ATA IVR will announce the current LAN IP address of the ATA IVR will announce if DHCP in enabled or disabled. IVR will announce current in use VoIP number IVR will announce the current network mask of the ATA. IVR will announce the current gateway IP address of the ATA.

IVR will announce the current setting in the Primary DNS field.

IVR will announce the version of the firmware running on the ATA. The system will change to DHCP Client type

DHCP will be disabled and system will change to the Static IP type.

Must set Static IP first.

You can set the codec you want to the first priority.

You can set the Handset gain to proper value, default is 6 You can set the Handset volume to proper value, default is 10

User’s Guide

Page 5

ATA-171/172/171P (ATA-S1/S2/P)

3 Setup the ATA by Web Browser

The ATA provides a built-in web server. You can use Web browser to configure the ATA. First please input the IP address in the Web page. In the end of IP address, please add the port number “:9999”. Ex: http://192.168.1.100:9999

3.1 Login.

3.1.1 Please input the username and password into the blank field. The default setting is:

1. For Administrator, the username is: root; and the password is: null. If you use the account login, you can configure all the setting.

2. For normal user, the username is: user; and the password is: test. If you use the account login, but you cannot configure the SIP setting.

3. WAN port IP address is DHCP mode, please use #126# to hear WAN port get IP address.

3.1.2 Click the “Login” button will move into the ATA web based management information page.

3.1.3 If you change the setting in the Web Management interface, please do remember to click the

“Submit” button in that page. After you finished the change of the setting, click the “Save” function in the left side, and click the Save Button. When you finished the setting, please click the Reboot function in the left side, and click the Reboot button in that page. After the system restart, all the setting can work properly.

User’s Guide

Figure 1. Login

Page 6

3.2 System Information for the ATA.

3.2.1 When you login the web page, you can see the ATA current system information like firmware

version, company… etc in this page.

3.2.2 Also you can see the function lists in the left side. You can use mouse to click the function you

want to set up.

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

3.3 Phone Book

3.3.1 In Phone Book page contains (from page 1~14).

3.3.2 Phone : show serial number.

3.3.3 Name : setting other side telephone number

3.3.4 URL : other side IP address

Figure 2. System Information

Example :

When you dial 1# the device should search phone book,if search match number 1 will send out “070000002@192.168.15.210”, if not got match number will send out 1.

-1- If you need to add a phone number into the phone book, you need to input the position, the name, and the phone number (by URL type). When you finished a new phone list, just click the “Add Phone” button.

-2- If you want to delete a phone number, you can select the phone number you want to delete then click “Delete Selected” button.

-3- If you want to delete all phone numbers, you can click “Delete All” button.

Page 7

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

3.4 Phone Setting

3.4.1 In Phone Setting contains Call Forward, SNTP Settings, Volume Settings, Block Setting,

3.4.2 Call Forward function: you can setup the phone number you want to forward in this page.

Figure 3. Speed Dial

Caller ID, Auto Dial Setting, Flash Time Setting, Call Waiting, and T.38(FAX) Setting functions.

There are three type of Forward mode. You can choose All Forward, Busy Forward, and No Answer Forward by click the icon.

-1- All Forward: All incoming call will forward to the number you choosed. You can input the name(description) and the phone number in URL field. If you select this function, then all the incoming call will direct forward to the speed dial number you choose.

-2- Busy Forward: If you are on the phone, the new incoming call will forward to the number you choosed. You can input the name(description) and the phone number in URL field.

-3- No Answer Forward: : If you can not answer the phone, the incoming call will forward to the number you choosed. You can input the name(description) and the phone number in URL field. Also you have to set the Time Out time for system to start to forward the call to the number you choosed.

-4- When you finished the setting, please click the Submit button.

-5- If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Page 8

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 4. Forward Setting

3.4.3 SNTP Setting function: you can setup the primary and second SNTP Server IP Address, to get the date/time information. Also you can base on your location to set the Time Zone, and how long need to synchronize again. When you finished the setting, please click the Submit button.

Figure 5. SNTP Setting

Page 9

ATA-171/172/171P (ATA-S1/S2/P)

3.4.4 Volume Setting function: you can setup the Handset Volume, Ringer Volume, and the Handset Gain. When you finished the setting, please click the Submit button.

-1- Handset Volume is to set the volume for you can hear from the handset.

-2- Ringer Volume is to set the ringer volume for you can hear.

-3- PSTN-Out Volume is is to set the volume for you can hear from the PSTN side.

-4- Handset Gain is to set the volume send out to the other side’s handset.

-5- PSTN-In Gain is to set the volume send out to the other side.

-6- When you finished the setting, please click the Submit button.

-7- If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

Figure 6. Volume Setting

3.4.5 DND Setting function: you can setup the DND Setting to keep the phone slience. You can choose Always Block or Block a period.

-1- Always DND: All incoming call will be blocked until disable this feature.

-2- DND Period: Set a time period and the phone will be blocked during the time period. If the “From” time is large than the “To” time, the Block time will from Day 1 to Day 2.

-3- When you finished the setting, please click the Submit button.

-4- If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Page 10

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 7. DND Setting

3.4.6 Caller ID function: you can set the device to show Caller ID in your PSTN Phone or IP Phone.

-1- There are four selection of Caller ID. You need to base on your environment to set the Caller ID function for FSK or DTMF. When you change the setting, please also double check the PTT seting in Others. You need to choose the correct country code then the Caller ID will be effect.

-2- When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Figure 8. Caller ID Setting

Page 11

ATA-171/172/171P (ATA-S1/S2/P)

3.4.7 Auto Dial Setting function: This function is when you input the phone number by the keypad but you don’t need to press “#”. After time out the system will dial directly. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

Figure 9. Auto Dial Setting

Drop Prefix - No (add number): when the rule match will direct add

number。

- Yes (reduce number): when the rule match will cut match number then add you setting number。

Replace rule1

Auto Dial Time Wait setting time then auto dial number Submit [Button]

Reset [Button]

For example:

Setting dial number rule。 +: or。 xxx: number limit。

Save setting value。 Clean all setting。

Page 12

ATA-171/172/171P (ATA-S1/S2/P)

1: Drop prefix: No, Replace rule 1: 002, 8613+8662。

Comment 1：when you dial number match 8613，device will auto add 002；dial out number is

[002+8613+xxx]。

Comment 2：when you dial number match 8662，device will auto add 002；dial out number is

[002+8662+xxx]。

2：Drop prefix: Yes, Replace rule 2: 006, 002+003+004+005+007+009；

comment 1：when you dial number has 002，device should drop all the 002，then change to 006；

dial out number is [006+xxx]。

Comment 2：when you dial number has 003，device should drop all the 003，then change to

006；dial out number is[006+xxx]。

3:Drop prefix: No, Replace rule 3: 009, 12。

Comment 1：when you input 12，device should match 12 number auto add 009；dial out number

is [009+12+xxx]。

4:Drop prefix: No, Replace rule 4: 007, 5xxx+35xx+21xx。

Comment 1：if you input number is 5xxx，when device search match 5 and after 3 number should

auto add 007；device dial out number is [007+5xxx]。

Comment 2：if you dial out number is 534，when device search match 5 and after add 2 number

date ；this rule is not match above dial number rule;dial out number is [534]。

Comment 3：if you input number has 35xx，device search match 35 and after add 2 data should

auto add 007；dial out number is[007+35xx]。

Comment 4：if you dial out number not match setting rule ,device should dial out you dial

number 。

3.4.8 Flash Time Setting function: When you use the PSTN Phone and you need to press the Hook to do the Flash (Switch to the other phone line or HOLD), this function is for you to set the time you press the Hook to represent the Flash function. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

Page 13

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 10. Flash Time Setting

3.4.9 Call Waiting Setting function: You can Enable/Disable the Call Waiting function, When you are talking with someone, there is a new incoming call, you will hear the call waiting tone. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Figure 11. Call Waiting Setting

3.4.10 T.38 Setting function: You can Enable/Disable the T.38 function. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the

Page 14

ATA-171/172/171P (ATA-S1/S2/P)

Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

Figure 12. T.38 (FAX) Setting

3.5 Hot line

This function is support auto dial to you setting hot line number, when you setting this function device should can not dial any number.

3.6 Alarm setting

Page 15

ATA-171/172/171P (ATA-S1/S2/P)

Alarm time: setting telephone ring time,when you setting time with current time are match device should produce a ring ,this time format is 24 hours.

3.7 Network

3.7.1 In Network you can check the Network status, WAN setting,LAN setting,DDNS settings and VLAN Settings.

3.7.2 Network Status: You can check the current Network setting in this page.

User’s Guide

Figure 13. Network Status

3.7.3 WAN and LAN Settings:

-1- If you change the WAN port’s setting to Fix IP Mode, then you have to make sure the IP address. Net Mask, Gateway, and DNS setting is suitable in your current network environment

-2- The WAN port is DHCP Client mode, You can change the setting to Fixed IP or PPPoE Mode.

-3- If you change the WAN port’s setting to PPPoE Mode, you have to input a correct username/password to get the IP address from your Internet Service Provider..

-4- The LAN port’s default IP address is 192.168.123.1, Net Mask is 255.255.255.0., and DHCP Server enabled. The start IP address if 150, end IP adress is 200. It is not necessary to change the LAN settings.

-5- You can connect your PC to the LAN port, set your PC as DHCP Client mode, then you can get IP addreess from the TA.

-6- When you finished the setting, please click the Submit button.

Page 16

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 14. Network Settings

Bridge Setting: If you don’t want to use the NAT Mode, then you can set the network setting in this page.

-8- The TCP/IP Configuration item is to setup the LAN port’s network environment. You may refer to your current network environment to configure the VoIP Phone properly.

-9- If you change the LAN port’s setting to Fix IP Mode, then you have to make sure the IP address. Net Mask, Gateway, and DNS setting is suitable in your current network environment.

-10- If you change the LAN port’s setting to DHCP Client Mode, then you have to make sure in your current network environment has a DHCP server, then the TA will get the IP address from the DHCP Server.

-11- If you change the LAN port’s setting to PPPoE Mode, you have to input a correct username/password to get the IP address from your Internet Service Provider.

-12- If you set the Bridge On, then the two Fast Ethernet ports will be transparent. Usually, we suggest you set the Bridge Mode is Enable, it will easy for you to connect any one of the port to the IP Network.

-13- When you finished the setting, please click the Submit button.

-14- If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Page 17

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 155. WAN Settings

Page 18

ATA-171/172/171P (ATA-S1/S2/P)

3.7.4 DDNS Setting: You can configure the DDNS setting in this page. You need to have the DDNS account and input the informations properly. You can have a DDNS account with a public IP address then others can call you via the DDNS account. But now most of the VoIP applications are work with a SIP Proxy Server. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

Figure 16. DDNS Setting

Page 19

ATA-171/172/171P (ATA-S1/S2/P)

3.7.5 VLAN Setting: You can set the VLAN setting in this page. There are two parts in this page. First one is to set the packets related to the TA, and the second parts is if you use the VLAN setting in the NAT Mode.

-1- There are two kind of destination packets will come from the TA’s WAN port, one kind of packets will go to the TA, the other will go through the LAN port to the PC.

-2- VLAN Packets: if you enable the first VLAN Packets and set the VID, User Priority, and CFI, then all the incoming packets will be check with the IP Address and the VID.

-3- VID: You can follow your service provider to set your VID.

-4- User Priority: Defines user priority, giving eight (2^3) priority levels. IEEE 802.1P defines the operation for these 3 user priority bits. Usually this will be defined by your service provider.

-5- CFI: Canonical Format Indicator is always set to zero for Ethernet switches. CFI is used for compatibility reason between Ethernet type network and Token Ring type network. If a frame received at an Ethernet port has a CFI set to 1, then that frame should not be forwarded as it is to an untagged port.

-6- When you enable the first VLAN Packets and set the VID, User Priority, and CFI, then all the incoming packets with the TA’s IP address and the same VID will be accept by the TA. If the incoming packets with the TA’s IP address but the different VID then the packets will be discard by the TA. The Other incoming packets with different IP address will go through the LAN port to the PC.

-7- NAT VLAN Setting: When you set your device in NAT mode, the TA can help you to filter the wrong incoming packets. You can separate the other device connectd behind the TA into 4 VLAN group. You can set different VID for these 4 groups. When the incoming packets go through the TA’s WAN port then the TA will check the VID, if the packets is not going to the TA(with the TA’s IP address and the correct VID), and the VID is not these four VID you set, then the packets will be discard by the TA.

-8- If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

Figure 17. VLAN Setting

3.8 Virtual Server Setting

Page 20

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Virtual Server Page To browse through different pages, click on the drop down box and select

the page number you wish to view.

Num This column displays the serial numbers, ranging from 0-23. There are

24 records in total.

Enable Click on the check box to enable this option, the default option is

unchecked (disabled). Protocol Displays the TCP and UDP port information. In Port Displays the internal port number Ex Port Displays the external port number Server IP Shows the IP address of the Server Select To select a specific Virtual Server and perform configurations, click on the

check box according to the server that you wish to configure. Enable Selected [Button] Delete Selected [Button] Delete All [Button]

Reset [Button] Num [Button] Specify which record to insert the server on the table. The allowable

Enable the selected server

Delete the selected server

Delete all data。

Clean all data。

range is 0-23.

Page 21

ATA-171/172/171P (ATA-S1/S2/P)

3.9 PPTP setting

PPTP Server : the server address provided by your ISP. PPTP Username : the username is provided by your ISP. PPTP Password : the password is provided by your ISP.

3.10 SIP Settings

User’s Guide

3.10.1 In SIP Settings you can setup the Service Domain, Port Settngs, Codec Settings, RTP Setting, RPort Setting and Other Settings. If the VoIP service is provided by ISP, you need to setup the related informations correctly then you can register to the SIP Proxy Server correctly.

3.10.2 Subscribe for MWI : this function is offer voice mail notify.

3.10.3 I In Service Domain Function you need to input the account and the related informations in this page, please refer to your ISP provider. You can register three SIP account in the TA. You can dial the VoIP phone to your friends via first enable SIP account and receive the phone from these three SIP accounts. For the second phone you can use the same way to register.

-1- First you need click Active to enable the Service Domain, then you can input the following items: (1-1) Display Name: you can input the name you want to display. (1-2) User Name: you need to input the User Name get from your ISP. (1-3) Register Name: you need to input the Register Name get from your ISP. (1-4) Register Password: you need to input the Register Password get from your ISP. (1-5) Domain Server: you need to input the Domain Server get from your ISP. (1-6) Proxy Server: you need to input the Proxy Server get from your ISP. (1-7) Outbound Proxy: you need to input the Outbound Proxy get from your ISP. If your

ISP does not provide the information, then you can skip this item.

(1-8) Register Period: you need to input the Register Period get from your ISP. This is

count in minute.

(1-9) You can see the Register Status in the Status item. If the item shows “Registered”,

then your TA is registered to the ISP, you can make a phone call direcly.

(1-10) If you have more than one SIP account, you can following the steps to register to the

other ISP. (1-11) When you finished the setting, please click the Submit button. (1-12) If there is nothing need to change, please click the Save Change Item in the left

side, then click the Save button. The change you made will save into the system

and the system will Reboot automatically.

Page 22

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 18. Service Domain Setting

3.10.4 Port Settings: you can setup the SIP and RTP port number in this page. Each ISP provider will have different SIP/RTPport setting, please refer to the ISP to setup the port number correctly. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Page 23

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 19. Port Setting

3.10.5 Codec Settings: you can setup the Codec priority, RTP packet length, and VAD function in this page. You need to follow the ISP suggestion to setup these items. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Figure 20. Codec Setting

Page 24

ATA-171/172/171P (ATA-S1/S2/P)

3.10.6 Codec ID Setting: Sometimes 2 VoIP device with different Codec ID will cause the interopability issue. If you are talking with others got some problems, you may ask the other one what kind of Codec ID he use, then you can change your Codec ID. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

Figure 21. Codec ID Setting

3.10.7 DTMF Setting: you can setup the RFC2833 Out-Band DTMF, Inband DTMF and Send DTMF SIP Info in this page. To change this setting, please following your ISP information. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Page 25

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 22. DTMF Setting

3.10.8 RPort Function: you can setup the RPort Enable/Disable in this page. To change this setting, please following your ISP information. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Figure 23. RPort Setting

Page 26

ATA-171/172/171P (ATA-S1/S2/P)

3.10.9 Other Settings: you can setup the Hold by RFC, Voice/SIP QoS and SIP expire time in this page. To change these settings please following your ISP information. When you finished the setting, please click the Submit button. The QoS setting is to set the voice packets’ priority. If you set the value higher than 0, then the voice packets will get the higher priority to the Internet. But the QoS function still need to cooperate with the others Internet devices. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

3.11 NAT Trans.

Figure 24. Other Setting

3.11.1 In NAT Trans. you can setup STUN function. These functions can help your ATA working properly behind NAT.

3.11.2 STUN Setting: you can setup the STUN Enable/Disable and STUN Server IP address in this page. This function can help your TA working properly behind NAT. To change these settings please following your ISP information. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Page 27

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 205. STUN Setting

3.12 Others

3.12.1 In Others you can setup Auto Config, FXS Port Setting and MAC clone Setting function. The function can configure your VoIP Phone automatically.

3.12.2 Auto Config: you can setup the Auto Configuration Enable/Disable and auto configuration by FTP or TFTP. You need to select the way to do the Auto Configurationand set the Server IP address in this page. This function can automatically download the configure file to setup your TA.

3.12.3 When you finished the setting, please click the Submit button.

3.12.4 If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

Page 28

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 216. Auto Configuration Setting

Auto Configuration Default setting is Off (not executed). Specify the methods on how auto

configuration will be performed, the options are TFTP, FTP or HTTP.

TFTP Server Set the TFTP Server’s location, you can input IP address or Domain Name

information in this text box.

HTTP Server Set the HTTP Server’s location, you can input IP address or Domain Name

information in this text box.

HTTP Path Specify the path to store data, for e.g. /123/

FTP Server Set the FTP Server’s location, you can input IP address or Domain Name

information in this text box.

FTP Username

FTP Password Enter the relevant password associated with the inputted username to log

File Path Specify the path to store data, for e.g. /123/

Submit [Button] Saves the configuration

Reset [Button] Erases the configuarion

Enter the relevant Username to log on to the FTP Server。

on to the FTP Server

Page 29

ATA-171/172/171P (ATA-S1/S2/P)

3.12.5 Auto configuration example

User’s Guide

Example 1: Auto Configuration: HTTP，HTTP Server: 192.168.1.50，HTTP Path: /file/。

Explanation： device will connect to the HTTP Server’s /file/ folder path and search the matching

file。

2：Auto Configuration: FTP，FTP Server: 192.168.1.150，FTP Username: test，FTP Password: test，

File Path: /file/。

Comment 1：device will connect to the FTP Server’s /file/ folder path and search the matching

file 。

Page 30

ATA-171/172/171P (ATA-S1/S2/P)

3.12.6 How to produce auto Configuration file.

1： Firstly, you need to find the MAC address of the device that you want to configured，for e.g. MAC Address: 00059e812118。

User’s Guide

Explanation 1：open the [MACList.txt] file then enter the these information in order[MAC Address,

Display Name, User Name, Register Name, Register Pass](example ：00059e812118, UN_DO, 105, 105, 105)，when completed, please save your file.

Explanation 2：open the [StandardCFG.dat] file (use Windows notepad program to open the

file)，then change the configurations parameters accordingly, once finished, please save the file。

Explanation 3：open the [MakeMACF.exe] file ，download [MAC File: MACList.txt, Standard File:

StandardCFG.dat]，select [Start]，then encrypt the file。

Explanation 4：the program will produce a encrypted string [00059e812118.dat] as the filename。 Explanation 5：please insert the name of the newly encrypted filename [00059e812118.dat] to

your [HTTP or FTP or TFTP Server] file path。

3.12.7 Advanced Setting

1. ICMP Setting: you can setup the ICMP echo Enable/Disable in this page. This function can

disable echo when someone ping this device, it can avoid haker try to attack the device. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

2. Send anonymous CID: this function is anonymous your all caller id.

3. Polarity Reverasl:when callee side pick up telephone will send a reversal.

4. Send flash event:this function must your proxy server has support.when you active this function

press flash key should send a event to proxy server to do the transfer or flash.

Page 31

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 228. Advanced Setting

3.12.8 FXS impedence Setting: you can setup the FXS in this page. When you are using different country’s PSTN Phone, you have to set the country’s setting to meet the requirement. When you finished the setting, please click the Submit button. (For ATA-171P only)

Figure 239. FXS impedence Setting

Page 32

ATA-171/172/171P (ATA-S1/S2/P)

(based on the arrangement of time).

Default setting is 14 days, which means the system will take 14 days to

3.13 MAC Clone setting

MAC Clone setting: This function changes the MAC Addresses of workstations in a LAN to which that

are identical to the WAN port; this is done due to the fact that some ISP companies restrict the use of multiple MAC Addresses through PPPoE.

3.14 Auto update

User’s Guide

Update via Default setting is “Off” (do not execute update). There are three

methods provided for automatic update, these are; TFTP, FTP, HTTP. Check new Firmware

Scheduling (Date)

Default option is “Scheduling”

Checks whether or not there is a newer version provided. “Power On”

option checks for newer version everytime when the system is powered

on, while scheduling is based on the arranged time.

- Power On + Scheduling: checks if a newer version is available everytime

the system is booted as well as the time it has been assigned to perform

the task.

Page 33

ATA-171/172/171P (ATA-S1/S2/P)

check if a newer version is available. The least amount of days that can

be specified is 1, while the most is 30. Scheduling (Time) Default setting is AM 00:00 – 05:59. Specifies the time sector to conduct

the check and update process. The exact time during the time sector is

randomly chosen by the system. There are four time sectors to choose

from, these are; AM 00:00 - 05:59, AM 06:00 – 11:59, AM 12:00 – 17:59,

AM 18:00 – 23:59. Automatic Update Default setting is Notify only. Automatic update requests will be notified

to users, the Automatic option will execute without any prior notice.

- Notify only: It will send messages to notify that there is a newer

version available, but automatic updates will not be performed. For

phones, the LCD will display the messages, while for Gateway, it will notify

with a series of beeping noise when the phone is picked up for the first

time.

-Automatic: Automatically execute the update process. Firmware File Prefix Next update time The time that the next check and update process will be on. Submit [Button] Saves the configuration. Reset [Button] Erases the configuration.

Example 1：Update via: HTTP，Check new firmware: Scheduling，Scheduling (Date: 14)，Scheduling

(Time): AM 00:00-05:59，Automatic Update: Automatic；Firmware File Prefix: TA1S。 Explanation 1：Based on the defined configuration, update will commence everything 14 days.

It will check the HTTP Server to identify if any newer versions are available, if there is, it will automatically execute the update process.

Explanation 2：Auto Update must comply with Auto Configuration Setting, therefore set the

relevant settings in the Auto Configuration Setting as; Auto Configuration: HTTP, HTTP Server 192.168.1.50, HTTP Path: /file/

Example 2： Update via: FTP，Check new firmware: Power，Scheduling (Date: 30)，Scheduling (Time):

AM 00:00-05:59，Automatic Update: Notify；Firmware File Prefix: TA1S。 Explanation 1：Based on the defined configuration, update will commence everything 14 days.

It will check the FTP Server to identify if any new versions are available, if there is, a notification message will be sent. If the user is using a phone and picks it up, 3 series of beep will be heard. At this point, if the user wants to force the update procedure, please press “#190#” to unlock the keypad function, then press “#160#” to execute the update process.

Explanatio 2: Auto Update must comply with Auto Configuration Setting, therefore set the

relevant settings in the Auto Configuration Setting as; Auto Configuration: FTP, FTP Server: 192.168.1.150, FTP Server: 192.168.1.150, FTP Username: test, FTP Password: test, File Path: /file/

Default setting is the product’s firmware number. Checks the relevant firmware version by matching the product’s firmware number.

User’s Guide

Page 34

ATA-171/172/171P (ATA-S1/S2/P)

3.14.1 Creation of The Auto Update File

Example 1：Create a filename “TA1S_ver.dat”,and input this string [Version: 0609100, Name:TA1S_]

in the first line of the content.

User’s Guide

Explanation 1：Create a file, where the filename is the Firmware File Prefix+_ver.dat，e.g.

TA1S_ver.dat.

Explanation 2: The contents of the file is [Version: 0609100, Name:TA1S_ ]. The “Version:

0609100” field represents the newer version of the firmware that the system will use for the auto update process (in this example it is 0609100), while the “Name:TA1S” field represents the Firmware File Prefix.

Explanation 3: The system will check the Firmware File Prefix+_ver.dat file, and at the same

time, check the version number, if the version is a newer version than the current version, auto update will commence. After it has been updated, the version name will be the combination of the Name+Version fields, e.g. TA1S_0609100.gz. Therefore, please make sure that the filename is correct.

Explanation 4: Place the TA1S_ver.dat and the new version of the firmware into the specified

path by the HTTP, FTP or TFTP Server.

3.14.2 (Call Transfer Operation)

Blind Transfer (Unconditional Transfer)

B calls A, A and B establishes a connection and during the conversation, A performs a call transfer to a third party. Firstly, A holds B’s conversation channel, presses #510# then keys in the number of the third party. After that, A presses the hash symbol “#” to initiate the call transfer to the third party.

Attendant Transfer

B calls A, A and B establishes a connection and during the conversation, A performs a call transfer to a third party. Firstly, A holds B’s conversation channel, presses #511# then keys in the number of the third party. After that, A presses the hash symbol “#” to initiate the call transfer to the third party C. C accepts the incoming call and establishes a conversation channel by answering the incoming ring tone, when A hangs up during the conversation with C, the call is transferred where B and C will be in the same conversation channel, allowing them to talk to each other.

Page 35

ATA-171/172/171P (ATA-S1/S2/P)

3.14.3 3-way calling (Conference)

B calls A, A and B establishes a connection and during the conversation, A would like to add another third party to the conversation. A holds the conversation channel with B, presses #512# then keys in the number of the third party. After that, A presses the hash symbol “#” to initiate the call to the third party C. Once C accepts the incoming call, A will then press the function button “flash” to enable the 3-way calling mode, where all three parties can now talk to one another.

3.14.4 (Call Waiting/Answering a Call on Waiting)

During the conversation between A and B, another third party C calls A, which A will notice from the call waiting tone that can be heard from A’s side of the conversation channel. A will then hold B on standby, while switching to a different line in order to communicate with C. If B is still on hold, and A would like to talk to B again, A can release the hold off B and continue the original conversation.

3.15 System Auth.

3.15.1 In System Authority you can change your login name and password. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically.

User’s Guide

Figure 30. System Authority

3.16 Save Change

3.16.1 In Save Change you can save the changes you have done. If you want to use new setting in the ATA, You have to click the Save button. After you click the Save button, the ATA will automatically restart and the new setting will effect.

Page 36

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 31. Save Change

3.17 Update Rom firmware:

3.17.1 In Update you can update the ATA’s firmware to the new one or do the factory reset to let the ATA back to default setting.

3.17.2 In New Firmware function you can update new firmware via HTTP in this page. You can ugrade the firmware by the following steps:

-1- Select the firmware code type, ROM code.

-2- Click the “Browse” button in the right side of the File Location or you can type the correct path and the filename in File Location blank.

-3- Select the correct file you want to download to the ATA then click the Update button.

-4- After finished the update firmware process, the system will Reboot automatically.

-5- This update page is special webpage you must add “update.htm” in you IP address. http://xxx.xxx.xxx.xxx:9999/update.htm.

Page 37

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 32. Update Firmware

3.17.3 In Default Setting you can restore the TA to factory default in this page. You can just click the Restore button, then the TA will restore to default and automatically restart again. The Default Setting will be NAT Mode, WAN port is DHCP Client Mode, LAN port is Fixed IP Mode and the IP Address is 192.168.123.1.

Page 38

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Figure 33. Restore Default Setting

3.18 Reboot

3.18.1 Reboot function you can restart the ATA. If you want to restart the ATA, you can just click the Reboot button, then the ATA will automatically.

Figure 34. Reboot System

Page 39

ATA-171/172/171P (ATA-S1/S2/P)

4 Setup the ATA by using Console (Hyper Terminal)

4.1 Configure the COM port

First Open the hyper terminal window, select the connection by the COM port, and then click the “Setting” button.

User’s Guide

Figure 24. Console Setting-1

Set the COM port’s setting as following setting. Then click OK.

Figure 25. Console Setting-2

Page 40

ATA-171/172/171P (ATA-S1/S2/P)

4.2 Login into the ATA

After finished the setting, click the “Connect” button (looks like a telephone icon). Then the hyper terminal is ready to connect to the ATA. Press “Enter” and the hyper terminal will show the “Login: “. Input “root” and press the “Enter” button. Then hyper terminal will show the “Password: “. Input “test” and press the “Enter” button. Now you already login the ATA. Please follow the CLI command list to configure the ATA with proper instruction and value.

User’s Guide

Figure 26. Console Screen

Page 41

4.3 Using CLI command to configure the ATA

4.3.1 CLI command list as below:

Index

1 ? Show CLI Command 2 arp ARP Configuration 3 ipconfig Interface Configuration 4 save Save to flash 5 reboot Reboot 6 exit Exit 7 debugmode Enter Debug Mode 8 update Update Flash Code/RAM

9 auth Change User Name and Password 10 nat NAT Configuration 11 dns DNS Configuration 12 ping ping [-lN] [IP-addr|host-name] 13 sip SIP Configuartion 14 ddns DDNS Configuartion 15 sntp SNTP Configuartion 16 vlan VLAN Configuartion 17 time Get System Time 18 mactab Show MAC Learning Table 19 dump Read/Write Memory 20 book Edit phone book 21 reload Reload Factory Setting 22 watchdog WatchDog Function 23 phone Phone Setting 24 weblogo Change Web's logo 25 dsp Show dsp type 26 addport Add Nat Port Mapping 27 cid Select slic Cid 28 slic read or write slic registers 29 ver Firmware Version

-1- “?” function is to show CLI command list in the screen.

-2- arp function Index

1 ? Show 'arp' Option 2 -a Show ARP Table 3 -d Delete ARP Table 4 -s Set Static ARP Table 5 (null) Show ARP Table

-3- ipconfig function Index

1 ? Show 'ipconfig' Option 2 -if0 Interface 0 3 -if1 Interface 1 4 -if2 Interface 2 5 -h Set Host Name 6 -a Set ARP Cache Expire 7 -r Restore Current Setting 8 (null) Show IP Setting

(3-1) ipconfig –ifN function  N is 0, 1, 2

Index

Command Description

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Page 42

ATA-171/172/171P (ATA-S1/S2/P)

1 ? Show 'ipconfig -ifN' Option 2 -t Set Host Type 3 -m Set MAC Address 4 -i Set IP Address 5 -nm Set Net Mask 6 -g Set Gateway 7 -dns0 Set Primary DNS server 8 -dns1 Set Secondary DNS server 9 -dr Set Default Route

10 -nat Set NAT

11 on Enable Interface 12 off Disable Interface 13 -dhcps DHCP Server Setting 14 -ddns Set DDNS 15 -bridge Set Bridge 16 -dev0 Set Device 0 Setting 17 -dev1 Set Device 1 Setting 18 -dev2 Set Device 2 Setting 19 (null) Show Interface Setting

-4- save function Index

1 ? Show 'save' Option 2 -book Save phone book 3 -sys Save system setting

-5- reboot function is to restart the system.

-6- exit function is to exit the CLI.

-7- debugmode function is to enter the debugmode.

-8- update function Index

1 ? Show 'update' Option 2 -os Update OSImage(IP filename) 3 -dsp Update DSP Image(IP filename) 4 -all Update All Image(IP filename) 5 -server Update Server (IP filename length) 6 -pcm PCM(IP filename)

-alaw alaw (IP filename)

-ulaw ulaw (IP filename)

-g729 g729 (IP filename)

-g726.16 g726.16 (IP filename)

-g726.24 g726.24 (IP filename)

-g726.32 g726.32 (IP filename)

-g726.40 g726.40 (IP filename) IP is the TFTP server’s IP address, and the filename is the image you want to download into the system.

-9- auth function Index

1 ? Show 'auth' Option 2 -admin Change Administrator user name/password 3 -sys0 Change System user0 user name/password

Command Description

User’s Guide

Page 43

ATA-171/172/171P (ATA-S1/S2/P)

4 -sys1 Change System user1 user name/password 5 -sys2 Change System user2 user name/password 6 -sys3 Change System user3 user name/password 7 -sys4 Change System user4 user name/password 8 -norm0 Change Normal user0 user name/password 9 -norm1 Change Normal user1 user name/password

10 -norm2 Change Normal user2 user name/password

11 -norm3 Change Normal user3 user name/password 12 -norm4 Change Normal user4 user name/password 13 -ppp Change PPP user name/password 14 (null) Show auth Setting

In each item includes

Index

1 ? Show 'auth' Option 2 -user Change User Name.'auth -sys3 -user xxx ' 3 -pass Change Password. 'auth -sys3 -pass xxx xxx' 4 (null) Show auth's System/PPP Setting

If you want to change the password, you need to type the password twice in the CLI.

-10- nat function Index

1 ? Show 'nat' Option 2 -vs Set 'nat -vs' Option 3 -dmz Set 'nat -dmz' Option 4 (null) Show NAT Setting

In DMZ item includes

Index

1 ? Show 'nat -dmz' Option 2 on EnableDMZ 3 off EnableDMZ 4 -ip Set DMZ IP address 5 (null) Show DMZ Setting

-11- dns function Index

1 ? Show 'dns' Option 2 -q DNS query. dns -q domain-name 3 (null) Show DNS Table

-12- ping function Index

1 ? Show 'ping' Option 2 -l ping [-l N] [IP-addr|host-name] 3 (null) ping [IP-addr|host-name]

Command Description

User’s Guide

Page 44

ATA-171/172/171P (ATA-S1/S2/P)

-13- sip function Index

1 ? Show 'sip' Option 2 -proxy0 sip -proxy0 3 -proxy1 sip -proxy1 4 -proxy2 sip -proxy2 5 -upnp sip -upnp on/off/show 6 -exts sip -exts sip upnp external-port 7 -extr sip -extr rtp upnp external-port 8 -sipp sip udp port 9 -rtpp sip rtp port

10 -stun sip -stun on/off

11 -rport sip -rport on/off 12 -sserver sip -sserver stun-server 13 -out sip -out outbound-proxy 14 -dump sip –dump 15 -log sip -log on/off 16 -drtp sip -drtp 0/1/2 17 -rtpnc sip -rtpnc on/off 18 -wanip sip –wanip 19 -nattype sip –nattype 20 -hbyrfc sip –hbyrfc 21 -dereg sip -dereg 22 -restart sip -restart 23 -jbt sip -jitter buffer Threshold 24 (null) Show SIP Setting

-14- ddns function Index

1 ? Show 'ddns' Option 2 -type Set DDNS Type 3 -host Set Host Name 4 -wild Set Wild Card Mode 5 -mx Set Mail Exchanger 6 -backmx Set Mail Exchanger Mode 7 -offline Set Offline Mode 8 -user Set Login User Name 9 -pass Set Login Password

10 (null) Show DDNS Setting

-15- sntp function Index

1 ? Show 'sntp' Option 2 -on Enable SNTP Client 3 -off Disable SNTP Client 4 -ip1 Set SNTP Server1 IP 5 -ip2 Set SNTP Server2 IP 6 -mode Set SNTP Client Mode 7 -zone Set GMT Time Zone: [+|-][hour]:[min] 8 -adjust Set Adjustment Time: [second] 9 (null) Show SNTP Setting

Command Description

User’s Guide

Page 45

ATA-171/172/171P (ATA-S1/S2/P)

-16- vlan function Index

1 ? Show 'vlan' Option 2 -tx Tx Vlan setting 3 -rx Rx Vlan setting 4 (null) Show Vlan Setting

-17- time function Index

1 ? Show 'Time' Option 2 -t Modify Time: hour:min:sec 3 -d Modify date: year:mon:date 4 (null) Show Data & Time

-18- mactab function is to show MAC learning table.

-19- dump function Index

1 ? Show 'dump' Option 2 -r dump -r XXXXxxxx 3 -w dump -w XXXXxxxx XX

-20- book function Index

1 ? Show 'book' Option 2 -a Show answer list 3 -c Show call list 4 -s speed dial 5 -p phone book

-21- reload function is to Reload Factory Setting, please make sure you want to do the factory

reset.

-22- watchdog function Index

1 ? Show 'WatchDog' Option 2 on Enable WatchDog 3 off Disable WatchDog 4 (null) Show WatchDog Setting

-23- phone function Index

1 ? Show 'phone' Option 2 -autoanswer phone auto answer 3 -vol Volume setting 4 -block Block Incoming call 5 -ring Set Melody Ringer 6 -forward Auto-forward Incall to Phone[0-9] in Book 7 (null) Show Phone Setting

Command Description

User’s Guide

Page 46

ATA-171/172/171P (ATA-S1/S2/P)

-24- weblogo function Index

1 ? Show 'weblogo' Option 2 -on Vender Logo 3 -off Default Logo 4 (null) Show weblogo Setting

-25- dsp function is to show dsp code type.

-26- addport function is to add Nat Port Mapping

-27- cid function Index

1 ? Show 'cid' Option 2 -off Disable Slic Cid signal 3 -1 Tx FSK after 1st Ring 4 -2 Tx FSK before 1st Ring 5 -3 Tx DTMF before 1st Ring 6 -4 Tx FSK with Line reversal before 1st Ring 7 -5 Tx DTMF with Line reversal before 1st Ring 8 -time FSK cid with time message 9 -single Single type FSK CID

10 (null) Show Cid Option

-28- slic function Index

1 ? Show 'slic' Option 2 -ring Issue Ring signal 3 -r read slic addr 4 -w write slic addr 5 -a read all slic reg 6 (null) Show slic register

-29- ver function is to show Firmware Version.

Command Description

User’s Guide

Page 47

5 How to make a phone call

When your ATA is configured properly, you can make a phone call to your friend in the same Service

provider.

If you want to make a phone call, you can dial the phone number and press “#” button to start to dial the

phone number.

The ATA also provides some functions that list as below:

1. Call Waiting: When a new call is coming while you are talking, you can push the Flash button to switch to the new call. You can push the Flash button to switch between the two calls.

2. Call Hold: You can push the Hold key to hold the current call for a while, then push Hold key again to keep talking.

3. 3-way conference: If you want to make a 3-way conference call, you can make a phone call to the first phone number. After the call is established, push the Flash button then you can hear the Dial tone, then make a phone call to the second phone number. When the second call is established, press the Flash button again.

ATA-171/172/171P (ATA-S1/S2/P)

User’s Guide

Welltech ATA-171P, ATA-171, ATA-172 V 1.6 Manual

Specifications and Main Features

Frequently Asked Questions

User Manual