WELLTECH ATA-151, ATA-152 Quick Manual

ATA-151/152

ATA-151/152

Quick Guide

Quick Guide

1. Copyright declaration

The copyright of the content which been
mentioned in this manual is owned by Welltech
computer Co., Ltd.

The copyright of brand and mark which been

mentioned is belong to its own company.

2005 Copyright Welltech computer Co., Ltd.

2. Before installation

Please check the following items before the
installation, that can avoid some unknown
problems during installation:

1.Preparing the following equipment for

installation:

a. A pc with network connection.
b. Ethernet RJ-45 cable
c. Phone and RJ-11 cable

2.Prepareing 1 of the following Network connection:

a. Static IP: a valid fixed IP address
b. DHCP: Make sure the DHCP server is

available.

c. PPPoE: Prepare a valid username and

password, further more,
confirm the XDSL modem is
functional.

3.Power

Make sure the power supply is adaptable.

3. Check the accessories

Please check the accessories after you open the
packing, there should have the parts as list in
below:

a. ATA mainframe X 1
b. 1M Ethernet RJ-45 cable with X 1
c. DC 12V, 1A Power adapter X 1
d. Document CD X 1, there is User guide and Quick

guide is embedded.

4

4.Physical Interface

4.1 Indicator

4.2 Connection port

6.For backing to factory default if this button is
pressed over 5 seconds.

7.For PC to connect to network with a RJ-45

ethernet cable that via ATA-151/152.

8. For ATA-151/152 to connect to a private network

or internet with a RJ-45 ethernet cable.

9. For connecting to PSTN(Fixed line) with a RJ-11

cable as backup if network failed.

10. For connecting to a analog telephone with a RJ-

11 cable.

11. Connect power adapter here.

1.PC connecting indicator

Light on: PC is connected
Light off: PC is disconnected

2.Network connecting indicator

Light on: Network is standby
Light off: Network is failed
Light flash: Data is transmitting

3.Phone active indicator

Light on: Phone is picked up
Light off: Phone is standby
Light flash: Incoming call

4.Registration indicator

Light on: Register is successful
Light flash: Register is failed

5.Power indicator

Light on: Power is ok
Light off: Power is failed

t

atu

S

s

P

h eon

L

AN

C

P

w

e

r

Po

ATA-151

1

2

6

7 8

9

1

0

11

ATA-151

ATA-152

4

4.Physical Interface

4.1 Indicator

4.2 Connection port

6.For backing to factory default if this button is
pressed over 5 seconds.

7.For PC to connect to network with a RJ-45

ethernet cable that via ATA-151/152.

8. For ATA-151/152 to connect to a private network

or internet with a RJ-45 ethernet cable.

9. For connecting to PSTN(Fixed line) with a RJ-11

cable as backup if network failed.

10. For connecting to a analog telephone with a RJ-

11 cable.

11. Connect power adapter here.

1.PC connecting indicator

Light on: PC is connected
Light off: PC is disconnected

2.Network connecting indicator

Light on: Network is standby
Light off: Network is failed
Light flash: Data is transmitting

3.Phone active indicator

Light on: Phone is picked up
Light off: Phone is standby
Light flash: Incoming call

4.Registration indicator

Light on: Register is successful
Light flash: Register is failed

5.Power indicator

Light on: Power is ok
Light off: Power is failed

tt

uS a

s

he

P o

n

L

A

N

C

P

w

e

rP

o

ATA-151

Figure 1.

1

2

3
4
5

Figure 2.

6

7 8

9

1

0

11

ATA-151

ATA-152

5. Start to installation

The following will show you how to install and

configure the ATA-151/152 step by step.

Scenario 1. XDSL connection

Connect to XDXL modem directly.
Please refer the figure 3 to install.

Step 1.

Plug RJ-45 cable for connecting from LAN port to

XDSL modem..

Step 2.

Plug RJ-11 cable for connecting to a valid analog

phone.

Step 3.

Plug RJ-11 cable CO PSTN line into PSTN port.

Step 4.

Plug the power adapter with valid power into DC 12V

port for getting adaptable power to ATA.

Step 5.

Now, please check the LED indicator for make sure if

the LED status as the following:

1. Power: ON

2. Status: Blinking

3. Phone: It should be off, if the handset of
analog phone is not picked up

4. LAN: ON

5. PC: ON

Step 6.

Plug RJ-45 cable for connecting from PC port.

Note:
Please disable the fuirewall to prevent some

error that during configuration if there is any
firewall software is installed. You can restart
the firewall after the configuration is finished.

PSTN

CO line

XDSL Modem

PC

Figure 3.

6

Scenario 1.1. Cordless connection

Also you can connect a cordless phone to ATA for

instead of a cord phone as figure 5 if you don't
want to be limited by a annoying cord, and there is
no any special setting.

Scenario 2 HUB connection

Connect to HUB or switch HUB directly.
Please refer the figure 6 to install.
All of step of setup is same with scenario 1.

PSTN

CO line

XDSL Modem

PC

Figure 5.

7

PSTN

CO line

XDSL Modem

PC

Figure 6.

HUB

Scenario 1.1. Cordless connection

Also you can connect a cordless phone to ATA for

instead of a cord phone as figure 5 if you don't
want to be limited by a annoying cord, and there is
no any special setting.

Scenario 2 HUB connection

Connect to HUB or switch HUB directly.
Please refer the figure 6 to install.
All of step of setup is same with scenario 1.

PSTN

CO line

XDSL Modem

PC

Figure 5.

7

PSTN

CO line

XDSL Modem

PC

Figure 6.

HUB