Weed Eater EBV200 Owner’s Manual
Trademark
Por favor, no devuelva el aparato al lugar de compra.
Please do not return unit to retailer.
Veuillez ne pa8 retourner routil au detaillant.
• 1-800-554-6723
www.weedeater.com
Instruction Manual
Manual de Instrucciones
Manuel d'lnstructions
EBV 200
FOR HOUSEHOLD USE ONLY
PARA USO CASERO SOLAMENTE
POUR UTILISATION .& DES FINS
DOMESTIQUES SEULEMENT
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTEN ClA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez life le manuel d'instructions et bien respecter tousles
avertissements et toutes les instructions de securit& Tout defaut
de le faire pourrait entraTner des blessures graves.
Electrolux Home Products, Inc. Electrolux Canada Corporation
104Warren Road 6150 McLaughlin Road
Augusta, GA30907 Mississauga, Ontario L5R4C2
[_ The Electrolux Group. The world's No. 1choK_.
KITCHEN, CLEANING AND OUTDOOR AppuANC_S COMBINED
Copyright =2004 Electrolux Home Products, inc. 530165112 5/15/04
IMPORTANT WARNINGS AND
SAFETY INSTRUCTIONS
,AWARNING:
When using electric gardening appliances, basic safety precautions should always
be followed to reduce the risk of fire, electric shock, and serious injury. The warnings
and safety instructions in this manual must be followed to reduce the risk of fire, elec-
tric shock, or injury, and to provide reasonable safety and efficiency in using this unit.
The operator is responsible for following the warnings and instructions in this manual
and on the unit. Read the entire instruction manual before assembling and using the
unit! Restrict the use of this unit to persons who read, understand, and follow the
warnings and instructions in this manual and on the unit. Never allow children to use
this unit. Close attention is necessary when used near children.
OPERATOR SAFETY
• Always wear safety glasses or similar
eye protection when operating, servic-
ing, or performing maintenance on your
unit. Wearing eye protection can help to
prevent rocks or debris from being
blown or ricocheting into eyes and face
which can result in blindness or serious
injury.
• Always wear a respirator or face mask
when working with the unit in dusty envi-
ronments.
• Dress safely in long pants. Do not go
barefoot or wear short pants or sandals.
• Do not operate the unit when you are
tired, ill, upset, or if you are under the in-
fluence of alcohol, drugs, or medication.
• Secure hair so it is above shoulder
length. Keep loose hair, loose clothing,
fingers, and all other parts of the body
away from openings and moving parts.
Hair, jewelry, loose clothing, or clothing
with loosely hanging straps, ties, tas-
sels, etc., can be caught in moving
parts.
ELECTRICAL SAFETY
_I_WARNING: Avoid a dangerous
environment. To reduce the risk of elec-
trical shock, do not use in rain, in damp
or wet locations, or around swimming
pools, hot tubs, etc. Do not expose to
snow, rain, or water to avoid the possibil-
ity of electrical shock. Do not handle ex-
tension cord plug or unit with wet hands.
• Use only a voltage supply as shown on
the nameplate of the unit.
• Avoid dangerous situations. Do not use
in presence of flammable liquids or
gases to avoid creating a fire or explo-
sion and/or causing damage to unit.
• Avoid dangerous environments. Do not
use in unventilated areas or where dust
or explosive vapors can build up.
• To reduce the risk of electrical shock,
use extension cords specifically marked
as suitable for outdoor appliances. The
electrical rating of the cord must not be
less than the rating of the unit. The cord
must be marked with the suffix "W-A" (in
Canada, '_#V"). Make sure your exten-
sion cord is in good condition. Inspect
extension cord before use and replace if
damaged. An undersized extension
cord will cause a drop in line voltage re-
sulting in loss of power and overheating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the
heavier the cord.
(NOTE: The correct size to be used de-
pending on the cord length is shown in
this manual. See SELECT AN EXTEN-
SION CORD in the ASSEMBLYsection).
• Inspect the insulation and connectors
on the unit and extension cord before
each use. Ifthere is any damage, do not
use until damage is repaired by your au-
thorized service dealer. Do not pull or
carry by cord; do not use cord as a han-
dle, close a door on cord, or pull cord
around sharp edges or corners. Keep
cord away from heated surfaces. Do not
unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
• Tie cord to cord retainer and connect to
recessed plug as shown in this manual
to prevent damage to unit and/or exten-
sion cord and to reduce the possibility of
the extension cord disconnecting from
the unit during operation.
• Do not use the unit ifthe switch does not
turn the unit on and off properly. Have
the unit repaired by your authorized ser-
vice dealer.
2
• Keeptheextensioncordclearofoper-
atorandobstaclesatalltimes.Donot
exposecordstoheat,oil,water,or
sharpedges.
• Avoidanybodycontactwithany
groundedconductor,suchasmetal
fences,orpipes,toavoidthepossibility
ofelectricshock.Don'thandleplugor
unitwithwethands.
• Donotusewithdamagedcordorplug.If
unitisnotworkingasitshould,hasbeen
dropped,damaged,leftoutdoors,or
droppedintowater,returnittoyourau-
thorizedservicedealerforrepair.
• GroundFaultCircuitInterrupter(GFCI)
protectionshouldbeprovidedonthecir-
cuitoroutlettobeusedforthisunit.Re-
ceptaclesareavailablehavingbuilt-in
GFCIprotectionandmaybeusedfor
thismeasureofsafety.
• Keepothersincludingchildren,animals,
bystanders,andhelpersaminimumof
30feet(10meters)away.Stopthemo-
torimmediatelyifyouareapproached.
Donotallowtheunittobeusedasatoy.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help
protect against electric shock. Double
insulation construction consists of two
separate "layers" of electrical insula-
tion instead of grounding.
Tools and appliances built with a
double insulation system are not in-
tended to be grounded. No grounding
means is provided on this unit, nor
should a means of grounding be add-
ed to this unit. As a result, the exten-
sion cord used with your unit can be
plugged into any standard 120 volt
electrical outlet. Safety precautions
must be observed when operating any
electrical tool. The double insulation
system only provides added protection
against injury resulting from an internal
electrical insulation failure.
WARNING: All electrical repairs to
this unit, including housing, switch, motor,
etc., must be diagnosed and repaired by
qualified service personnel. Replacement
parts for a double insulated appliance
must be identical to the parts they replace.
A double insulated appliance is marked
with the words "double insulation" or
"double insulated". The symbol []
(square within a square) may also be
marked on the appliance. Failure to have
the unit repaired by Sears service person-
nel can cause the double insulation con-
struction to become ineffective and result
in serious injury.
UNIT/MAINTENANCE SAFETY
• Turn off all controls and allow the motor
to stop before disconnecting the unit
from the power source.
• Disconnect the unit from the power
source when not in use. Do not leave
the unit when it is plugged into outlet.
• Do not set the unit on any surface ex-
cept a clean, hard area while the unit is
running. Debris such as gravel, sand,
dust, grass, etc., could be picked up by
the air intake and thrown out through the
discharge opening, damaging the unit,
property, or causing serious injury to by-
standers or operator.
• Do not overreach or use from unstable
surfaces such as ladders, trees, steep
slopes, rooftops, etc. Use extra care
when cleaning on stairways. Keep firm
footing and balance at all times. Keep
hands out of tubes.
• Inspect the entire unit before each use
for worn, loose, missing, or damaged
parts. Do not use until the unit is in
proper working order.
• Disconnect unit from power source be-
fore servicing, cleaning, performing
maintenance, or storing.
• This unit is double insulated. See the
DOUBLE INSULATION CONSTRUCTION
section. Have all internal service per-
formed by qualified service repair per-
sonnel to avoid creating a hazard or
voiding your warranty.
• Have all maintenance other than the
recommended procedures described in
the instruction manual performed by
your authorized service dealer.
• Always see your authorized service
dealer to replace a damaged impeller.
Parts that are chipped, cracked, broken,
or damaged in any other way can fly
apart and cause serious injury. Replace
damaged parts before using the unit.
• Never place any object in the air intake
opening as this could restrict proper air
flow and cause damage to the unit.
• Never douse the unit with water or other
liquids or squirt with awater hose. Clean
the unit using a damp cloth. Wipe off
with a clean dry cloth. See MAINTE-
NANCE.
• Check air intake openings and tubes
frequently, always with the unit stopped
and power source disconnected. Keep
vents and tubes free of debris which can
accumulate and restrict proper air flow.
• Do not burn, incinerate, or expose this
unit to extreme heat.
• Store the unit unplugged in a high, cool,
dry, indoor area out of the reach of chil-
dren.
• Useonlyrecommendedattachments
andreplacementpartstoavoidcreating
ahazardand/orvoidingwarranty.
• Maintaintheunitaccordingtorecom-
mendedprocedures.
• UseonlyforjobsexplainedintheOP-
ERATIONsectionofthismanual.
BLOWER SAFETY
• Use only in daylight or in good artificial
light.
• Inspect the area before using the unit.
Remove all debris and hard objects
such as rocks, glass, wire, etc., that can
ricochet, be thrown, or otherwise cause
injury or damage during operation.
• Avoid accidental starting. Be sure the
switch is in the OFF position and keep
your hand and fingers away from the
switch while connecting the unit to the
power source or when carrying a unit
connected to the power source.
• Never run the unit without the proper
equipment attached. When used as a
blower, always install a blower tube. Use
only recommended attachments. Do
not use with any opening blocked, Keep
free of dust, lint, hair and anything that
may reduce air flow.
• To avoid spreading fire, do not use blow-
er near leaf or brush fires, fireplaces,
barbecue pits, ashtrays, etc.
• Never place objects inside the blower
tubes; always direct the blowing debris
away from people, animals, glass, and
solid objects such as trees, automo-
biles, walls, etc. The force of air can
cause rocks, dirt, or sticks to be thrown
or to ricochet which can hurt people or
animals, break glass, or cause other
damage.
• Never use for spreading chemicals, fer-
tilizers, or any other substances which
may contain toxic materials.
VACUUM SAFETY
• Stop the motor and disconnect tile pow-
er source before opening the air inlet
door or attempting to insert or remove
the vacuum tubes. The motor must be
stopped and the impeller blades no
longer turning to avoid serious injury
from the rotating blades.
• Hard objects can be thrown through the
collection bag or the housing and be-
come dangerous missiles which can
cause serious injury to the operator or
others.
• When using the vacuum attachment,
the unit is designed to pick up dry mate-
rial such as leaves, grass, small twigs,
and bits of paper. Do not vacuum
stones, gravel, metal, broken glass, etc.,
to avoid severe damage to the impeller.
To avoid the possibility of electrical
shock, do not attempt to vacuum water
or other liquids.
• Never run the unit without the proper
equipment attached. When used as a
vacuum, always install vacuum tubes
and collection bag assembly. Make sure
the collection bag assembly is com-
pletely zipped when unit is running to
avoid flying debris. Use only recom-
mended attachments.
• Avoid situations which could set the col-
lection bag on fire. Do not vacuum dis-
carded matches, cigars, cigarettes, or
ash from fireplaces, barbecue pits,
brush piles, etc. To avoid spreading fire,
do not use blower near leaf or brush
fires, fireplaces, barbecue pits, ash-
trays, etc.
• Always use the collection bag shoulder
strap when vacuuming to avoid loss of
control.
• Check air intake openings, elbow tube,
and vacuum tubes frequently, always
with the unit stopped and the power
source disconnected. Keep vents and
tubes free of debris which can accumu-
late and restrict proper air flow. Do not
use with any opening blocked, Keep
free of dust, lint, hair and anything that
may reduce air flow.
STANDARDS
This product is listed by Underwriters Lab-
oratories, Inc., in accordance with UL
Standard 1017.
If situations occur which are not covered
in this manual, use care and good judg-
ment. If you need assistance, contact
your authorized service dealer or call
1-800-554-6723. Failure to follow all
Safety Rules and Precautions can result
in serious injury.
SAVE THESE INSTRUCTIONS
A________
dt_WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover or attempting to in-
sert or remove the inlet restrictor, blower
tube, or vacuum tubes. The motor must
be stopped and the impeller blades no
longer turning to avoid serious injury from
the rotating blades.
_k, WARNING: If received assembled,
ensure your unit is properly assembled
and all fasteners are secure.
• A standard screwdriver is required for
assembly.
BLOWER ASSEMBLY
NOTE: Assembly instructions for using
your unit as a vacuum follow this section.
Attaching the blower tube
Ifyou have already assembled your unit
for use as a vacuum, refer to the section
HOW TO CONVERT UNIT FROM VACUUM
USE TO BLOWER USE.
To attach blower tube:
1. Align the grooves on the blower tube
with the grooves on the blower outlet.
2. Push the blower tube onto the blower
outlet until it snaps into place (tube is
secured by red tube release button).
3. To remove the blower tube, press the
tube release button while pulling on
tube.
Re easeButton
B,owerTobe
VACUUM ASSEMBLY
NOTE: Assembly instructions for using
your unit as a blower are explained in the
previous section.
If you have already assembled your unit
for use as a blower, remove the blower
tube.
Remove the inlet restrictor
An inlet restrictor is used when using your
unit as a blower. This restrictor is not used
during vacuum use and must be removed
during assembly for vacuum use.
NOTE: Be sure to keep the inlet re-
stricter for using your unit as a blower.
1. Ensure unit is stopped and extension
cord is unplugged.
2. Open the inlet cover by inserting the
tip of a screwdriver into the latch area
on the blower unit. Gently tilt handle
of screwdriver toward the front of the
unit to release the latch while pulling
up on the vacuum inlet cover with
your other hand.
Bottom view Latch Area
of unit
Vacuum Inlet Cover (closed)
Impelle Latch Area
Vacuum' nletCover (opened)
3. Turn the inlet restrictor counterclock-
wise and remove it from the unit. Do
not close the inlet door. You will next
attach the vacuum tubes.
l_"_l'_ V_/eCtcmver
Inlet _
Restdct_r _f'_/'_
Attaching the vacuum tubes
There are 2 vacuum tubes, an upper
tube and a lower tube. The upper tube
has a vacuum assist handle attached to
one end and is cut straight on both ends.
The upper tube attaches to the blower
unit. The lower tube has an angled end
that you point toward the ground during
vacuum use. The lower tube attaches to
the upper tube.
1. Ensure unit is stopped and exten-
sion cord is unplugged.
2. While holding inlet cover open, place
the hooks of the vacuum assist handle
on the retaining posts of the unit.
3. Raise the tube until it is secured to the
blower unit by the red inlet cover latch.
vUaPuPermV,_cuiutHTUnOcte
__Ji/
!_ Retah?ing Post
4.Toattachthelowervacuumtubeto
theuppervacuumtube,firstalignthe
arrowsonthetwotubes.Then,press
thetwotubestogetheruntilthelower
tubeissecurelyseatedintheupper
tube(about3inches).
_p_ UpperTubeLowerTube
r sonupper
" andlowertubes
COLLECTIONBAG ASSEMBLY
1. Open the zipper on the collection
bag and insert the elbow tube.
2. Push the small end ofthe elbow tube
through the small opening in the bag.
NOTE: Make sure edge of the small
opening is flush against the flared area
of the elbow tube and the hole for the
tube release button is on top.
Elbow Tube Tube
Zipper _1
Opening Opening
3. Close the zipper on the bag. Make
sure the zipper is closed completely.
4. Align the grooves on the elbow tube
with the grooves on the blower outlet.
5. Push the elbow tube onto the blower
outlet until it snaps into place (elbow
tube is secured by red tube release
button).
ADJUSTING THE SHOULDER STRAP
ON THE COLLECTION BAG
1. Carefully loop the shoulder strap
through the buckle as shown in the il-
lustration below.
Last IntQ _
2. Position the unit on your right-hand
side, blower outlet and bag pointing
toward the rear. Hold the unit in an
upright position with the lower vacu-
um tube on the ground to support it.
3. Place the shoulder strap over your
head and onto your left shoulder.
Release
Button
Hole
4. Adjust the strap to allow a free flow of
air from the blower. If the collection
bag is kinked, the unit will not operate
properly.
NOTE: The strap is designed to posi-
tion the collection bag on your shoulder
without kinks. The strap is not intended
to support the weight of the unit.
Shoulder strap
on left shoulder
No kinks in bag
allows
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
1. Stop unit and unplug the extension
cord.
2. Remove the vacuum tubes by insert-
ing the tip of a screwdriver into the
latch area on the vacuum assist han-
dle. Gently tilt handle of screwdriver
toward the front of the unit to release
the latch while pulling up on the vacu-
um assist handle with your other hand.
Latch Area
3. Install the inlet restrictor that was re-
moved when assembling forvacuum
use.
NOTE: If you are unable to locate the
inlet restrictor, the unit will still operate.
This restrictor improves the blower
function.
4. Remove the collection bag.
5. Close the inlet cover and make sure
it is latched closed.
6. Re-install the blower tube. Refer to AT-
TACHING THE BLOWER TUBE for
instructions on how to attach this item.
SELECT AN EXTENSION CORD
Use only a 120 A.C. voltage supply as
shown on nameplate of the unit to
power your blower.
• To reduce the risk of electrical shock,
this equipment has a polarized plug
(one blade is wider than the other) and
will require the use of a polarized
6
extensioncord.Theapplianceplug
willfitintoapolarizedextensioncord
onlyoneway.Iftheplugdoesnotfit
fullyintotheextensioncord,reverse
theplug.Iftheplugstilldoesnotfit,
obtainacorrectpolarizedextension
cord.Apolarizedextensioncordwill
requiretheuseofapolarizedwall
outlet.Thisplugwillfitintothe
polarizedwalloutletonlyoneway.If
plugdoesnotfitfullyintothewall
outlet,reversetheplug.Ifitstilldoes
notfit,contactaqualifiedelectricianto
installtheproperwalloutlet.Donot
changetheequipmentplug,extension
cordreceptacle,orextensioncord
pluginanyway.
Theextensioncordusedtoreachthe
powersourcemustbe:
• Specificallymarkedassuitableforout-
dooruse.Thecordmustbemarkedwith
thesuffix'_JV-A"(inCanada"W").
• Heavyenoughtocarryfullcurrentfrom
thepowersourcetotheunit.Otherwise,
lossofpowerandoverheatingcanoc-
curcausingdamagetounit.Referto
tableforminimumwiregaugerecom-
mendations.Thecordmustbemarked
withtheproperwiregauge.(Appropriate
extensioncordsareavailable.)Donot
usemultiplecords.
• Ingoodcondition.Cordinsulationmust
beintactwithnocracksordeterioration.
Plugconnectorsmustbeundamaged.
DONOTusemultiplecords.
MINIMUMWIREGAUGE
RECOMMENDATIONS
50 F'R 100 FT.
A.WG* A W.G.*
16 14
*American Wire Gauge
Secure the extension cord to the unit by
threading the cord through the cord re-
tainer (see illustration). Insert the cord
receptacle into the recessed plug.
CAUTION: Failure to use cord retain-
er could result in damage to the unit,
extension cord, or both.
C°rcdeptacI_ _ Recessed
oor
Retainer t_
KNOWYOUR ELECTRIC BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations to your unit to familiarize yourself with the location of
the various controls and adjustments. Save this manual for future reference.
Collection Bag
Elbow
Tube
Tube
Vacuum Assist Handle
Upper Vacuum Tube
Blower Tube
Lower Vacuum Tube
_// =====i
_Iet Restrictor
/
Z ====
ON/OFF SWITCH
The ON/OFF SWITCH is used to activate
the motor.
INLET COVER LATCH
The INLET COVER LATCH is used to open
and close the inlet cover and to secure
the upper vacuum tube to the blower
unit.
BLOWER TUBE
The BLOWER TUBE is designed to direct
the flow of air.
Zx
,_LWARNING: You MUST make sure
the tubes are secure before using the
unit.
£x _______
41SWARNING: Do not use the unit
without the tubes or collection bag proper-
ly attached to avoid flying debris and/or
impeller contact which can cause serious
injury. Always wear eye protection to pre-
vent rocks or debris from being blown or
ricocheting into the eyes and face which
can result in blindness or serious injury.
STOPPING YOUR UNIT
Slide the ON/OFF switch to the OFF
position.
INLET RESTRICTOR
Tile INLET RESTRICTOR improves the
blower function.
TUBE RELEASE BUTTON
The TUBE RELEASE BUTTON secures the
blower tube or elbow tube to the blower
unit during operation. Also, pressing the
tube release button allows removal of the
blower tube or elbow tube.
STARTING YOUR UNIT
Your unit has two run positions, LOW
and HIGH. Slide the switch to one of
these positions to turn on the unit.
OPERATING POSITION
Eye Protection Eye Protection
Blower Vacuum
USING YOUR UNIT AS A BLOWER
dt_WARNING: Inspect the area be-
fore using the unit. Remove all debris
and hard objects such as rocks, glass,
wire, etc., that can ricochet, be thrown,
or otherwise cause injury or damage
during operation.
Use your unit as a blower for:
• Sweeping debris or grass clippings from
driveways, sidewalks, patios, etc.
• Blowing grass clippings, straw, or
leaves into piles, or removing debris
from corners, around joints, or between
bricks.
Direct air flow by directing the blower
tube down or to one side. Always work
away from solid objects such as walks,
large stones, vehicles, and fences.
Clean corners by starting in corners and
moving outward. This will help prevent
an accumulation of debris which could
fly into your face.
Be careful when working near plants.
The force of the air could damage
tender plants.
USING YOUR UNIT AS A VACUUM
_,WARNING: Do not vacuum
stones, gravel, metal, broken glass,
etc., to avoid severe damage to the im-
peller. To avoid the possibility of electri-
cal shock, do not attempt to vacuum wa-
ter or other liquids.
Use your unit as a vacuum to pick up
dry material such as leaves, grass,
small twigs, and bits of paper.
• For best results during vacuum use,
operate your unit at high speed.
• Move slowly back and forth over the
material as you vacuum. Avoid forc-
ing the unit into a pile of debris as
this can clog the unit.
• Keep the vacuum tube about an inch
above the ground for best results.
_ILWARNING: If the unit becomes
clogged, stop the unit and unplug the ex-
tension cord. Wait until the impeller has
completely stopped turning, then re-
move the vacuum tubes. Carefully
reach into the vacuum opening and
clear out the clogged debris.
_ WARNING: Disconnect power
source before performing maintenance.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to opera-
tor abuse or negligence. To receive full
value from the warranty, the operator must
maintain unit as instructed in this manual.
Various adjustments will need to be made
periodically to properly maintain your unit.
BEFORE EACH USE
CHECK FOR LOOSE
FASTENERS AND PARTS
• Inlet Cover
• Blower Tube
• Vacuum Tubes
• Collection Bag
CHECK FOR DAMAGED OR
WORN PARTS
Contact your authorized service dealer
for replacement of damaged or worn
parts.
• ON/OFF Switch - Ensure switch func-
tions properly by moving the switch to
the OFF position. Make sure motor
stops; then restart motor and continue.
• Inlet Cover - Discontinue use of unit if
inlet cover fails to latch properly or if it is
damaged in any way.
AFTER EACH USE
INSPECT AND CLEAN UNIT & LABELS
Stop unit and unplug extension cord.
• After each use, inspect complete unit
for loose or damaged parts. Clean the
unit using a damp cloth.
• Wipe off unit with a clean dry cloth.
CLEAN COLLECTION BAG
IMPORTANT: THE COLLECTION BAG
MUST BE PROPERLY EMPTIED.
• You must properly empty and maintain
the collection bag to avoid deterioration
and obstruction of air flow.
• Remove the collection bag from the unit
and empty after each use. Do not store
bag without emptying the bag of all con-
tents (grass, leaves, etc.).
• Wash the bag once a year. Remove the
bag from the blower and turn the bag in-
side out. Wash the bag with a water
hose. Allow the bag to hang and dry
completely before you reuse the bag.
HOW TO REMOVE AN OBJECT
FROM THE AIR INTAKE
_,WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover. The motor must
be stopped and the impeller blades no
longer turning to avoid serious injury
from the rotating blades.
1. While holding the inlet cover open,
remove the vacuum tubes. The inlet
cover must be held open through all
remaining steps.
2. Carefully reach into the vacuum
opening and clear out the air intake
area. Clear all debris from impeller.
3. Inspect the impeller for cracks. If
cracked or damaged, do not use the
unit. Have parts replaced by your au-
thorized service dealer. Do not at-
tempt to replace them yourself.
il_ WARNING: Perform the following
steps after each use:
• Stop unit and disconnect from the pow-
er source.
• Allow motor to cool before storing or
transporting.
• Store unit with all guards in place. Posi-
tion unit so that any sharp object cannot
accidentally cause injury.
• Store unit unplugged, well out of the
reach of children.
SEASONAL STORAGE
Prepare unit for storage at the end of
the season or if it will not be used for
30 days or more.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source before
performing all ofthe recommended remedies below except remedies that re-
quire unit to be operating.
SYMPTOM CAUSE REMEDY
Unit fails to 1. Switch in the OFF position= 1=Slide switch to ON position.
operate. 2= Extension cord discon- 2=Reconnect extension cord.
Unit 1. Mechanical failure 1. Contact your authorized
vibrates service dealer.
abnormally.
Impeller will 1. Debris in air intake area. 1. Clean unit. Remove any
not turn 2. Mechanical failure, debris.
freely. 2. Contact your authorized
nected.
3=Circuit breaker tripped, or 3= Reset circuit breaker or
fuse blown, fuse.
4=Mechanical failure 4= Contact your authorized
If your blower is to be stored for a period
of time:
• Stop unit and disconnect from the pow-
er source.
• Clean the entire unit before lengthy stor-
age.
• Open inlet cover and clean any dirt,
grass, or debris that has collected. In-
spect the blower and all tubes. Close
and make sure the cover is latched.
• Clean air vents and air inlet of debris.
• Store your unit and extension cord in a
well ventilated area and covered, if pos-
sible, to prevent dust and dirt accumula-
tion. Do not cover with plastic. Plastic
cannot breathe and may cause con-
densation and eventual rust or corro-
sion.
• Check entire unit for loose screws. Re-
place any damaged, worn, or broken
parts.
service dealer.
service dealer.
10
ELECTROLUX HOME PRODUCTS,
INC., warrants to the original purchaser
that each new Weed Eater o brand elec-
tric or cordless product is free from de-
fects in material and workmanship and
agrees to repair or replace under this
warranty any defective Weed Eater_
brand electric or cordless product within
two (2) years from the original date of
purchase.
If your Weed Eater ® brand electric or
cordless product should fail within the
limited warranty period, return it, com-
plete, prepaid, with proof of purchase, to
the dealer from whom it was purchased
for repair or replacement at the option of
ELECTROLUX HOME PRODUCTS,
INC.
This warranty is not transferable and
does not cover damage or liability
caused by improper handling, improper
maintenance or the use of accessories
and/or attachments not specifically rec-
ommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Addi-
tionally, this warranty does not cover
parts that will wear and require replace-
ment with reasonable use during the
warranty period. This warranty does not
cover predelivery setup or normal ad-
justments explained in the instruction
manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTALOR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU,
The policy of ELECTROLUX HOME
PRODUCTS, INC., to continuously im-
prove its products. Therefore, ELEC-
TROLUX HOME PRODUCTS, INC., re-
serves the right to change, modify, or
discontinue models, designs, specifica-
tions, and accessories of all products at
any time without notice or obligation to
any purchaser.
11
Loading...