1234567
8
Need help?
Besoin d'aide?
¿Necesita ayuda?
1-800-727-4023
Wagner Technical Service
http://www.wagnerspraytech.com
Visit us on the world wide web!
Model 905 Power Steamer™
Owner’s Manual • Read this manual for complete instructions.
Guide d’utilisation • Ce manuel contient les instructions complètes.
Manual del propietario • Lea este manual para obtener instrucciones completas.
Read all warnings
Lisez tous les avertissements
Lea todas las advertencias
Allow unit to heat
Laissez chauffer l'appareil.
Deje que la unidad se caliente
Fill container (3 cups max)
Remplissez le réservoir (3
pot-verseur gradué maximum)
Llene el contenedor (3 taza
medidora máximas)
Score and remove wall paper
Éraflez légèrement le papier peint,
puis enlevez-le.
Marque y retire el papel tapiz
Call us for answers fast
In the United States, call:
Appelez-nous pour des résponses rapides.
Aux États-Unis, téléphonez sans frais au:
Llámenos primero para obtener respuestas
rapidas.
En los Estados Unidos, llame gratis al:
Attach trigger to steam plate
Assemblez la détente et la
plaquette de décollage
Coloque el gatillo en la placa
de vapor
Switch OFF (O) and unplug
Placez l'interrupteur en position
d'arrêt (O) et débranchez l'appareil
Apague la unidad (O) y desenchufe
Plug in power cord, switch ON (l)
Branchez le cordon d'alimentation et
mettez l'interrupteur en marche (l)
Enchufe el cable de alimentación y
encienda la unidad (l)
Allow unit to cool and refill
Laissez refroidir l'appareil et
remplissez-le de nouveau.
Deje que la unidad se enfríe y
vuelva a llenarla
0506 • Form No. 0282763A
EnglishFrançaisEspañol
WARNING
Read all safety information before operating the equipment
(A)
(C)
(B)
azard: Hot steam and parts. May cause injury,
H
Prevention:
• Stay clear of steam, hose, hose fittings and steam plate
surface. DO NOT place hand in front of steam plate.
Water drops are hot and may burn skin. Use extreme
•
c
e
gloves when using this steamer.
• Allow parts to cool before changing accessories and /or
opening fill cap.
• Never point steam plate or accessories at anyone.
• Hot water may eject from accessories and when trigger is
activated.
• DO NOT over fill water container.
• DO NOT strain or kink hose. Never repair a damaged
hose.
ncluding skin burns or property
i
amage. Temperatures exceed 212° F
d
100ºC).
(
aution when using steam plate overhead, and routinely
mpty water from steam plate. Wear eye protection and
• Read all instructions and warnings before each use.
Grounding Instructions
This product should be grounded. In the event of an electrical
hort circuit, grounding reduces the risk of electric shock by
s
providing an escape wire for the electric current. This product is
equipped with a cord having a grounding wire with an
appropriate grounding plug. The plug must be plugged into an
utlet that is properly installed and grounded in accordance with
o
all local codes and ordinances.
ANGER — Improper installation of the grounding plug can
D
result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, have
your nearest Wagner Authorized Service Center replace it.
Check with a qualified electrician or serviceman if the grounding
instructions are not completely understood, or if in doubt as to
whether the product is properly grounded. Do not modify the
plug provided; if it will not fit the outlet, have the proper outlet
installed by a qualified electrician.
Hazard: Fire. May cause severe injury and/or
Prevention:
• DO NOT allow water to boil dry. Boiling dry may cause
• DO NOT allow water or steam to enter light switches or
Hazard: Electrical Shock. May cause severe
Prevention:
• Power cord must be connected to grounded (3 prong)
• DO NOT use the unit if the power cord is worn or damaged.
• DO NOT pull water container by power cord.
• DO NOT allow water or steam to enter light switches or
Hazard: General. May cause injury and/or property
Prevention:
• DO NOT stand or sit on water container. (Use a step
•
• Water container must rest on a sturdy, level surface and in
•
• NEVER leave power steamer unattended.
property damage.
overheating and fire.
sockets.
injury.
outlet.
Never repair a power cord.
sockets.
damage.
ladder.)
DO NOT modify parts or components. Never repair
damaged or worn parts.
upright position.
Keep power steamer away from children.
Extension Cords
Use only a 3-wire extension cord that has a 3-blade grounding
plug, and a 3-slot receptacle that will accept the plug on the
product. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. An undersized cord
will cause a drop in line voltage resulting in loss of power and
overheating. For lengths up to 100 feet, use 14 AWG extension
cords.
Thermal Safety Fuse Reset
Always fill the unit before plugging it in. If the steamer is
plugged in before it is filled with water, or if the steamer is
allowed to run dry, a thermal safety fuse will open, causing the
unit to turn of
cool for at least 10 minutes. The safety fuse will reset itself.
f. If this happens, unplug the unit and allow it to
English
The water container, heating element and hose are not
serviceable. Should a problem occur with the steamer,
contact W
2
agner T
echnical Service.
Parts and Components:
(a)
(b)
(c)
(d)
(e)
(
f)
(g)
(n) (o)
(k)
(l)
(h)
(j)
(m)
(i)
Item Description
a) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power switch
b) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steam hose
c) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Jet nozzle
d) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Amber indicator light
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
e)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
f)
g). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water container (boiler)
h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steam plate
Trigger mechanism
Fill cap
Item Description
i). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extensions (2)
j) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Large cleaning brush
k) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Squeegee
l) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning towel
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
m)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
n)
o). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Measuring cup
Replaceable parts:
These parts can be ordered or replaced by calling Wagner Customer Service (1-800-727-4023).
Description
Steam plate
Jet nozzle and brushes (4)
Extension
Squeegee
Cleaning brush
Cleaning brush rags (3)
Replacement funnel and measuring cup
Nozzle brushes (4)
Funnel
3
English
Setup:
Amount of
water
16 oz.
32 oz.
48 oz.
Steam
time
15 min
30 min
45 min
1. Insert the carrying handle into its slot on the container as
shown. Secure the handle using the magnetic screwdriver
and screw.
2. Attach the steam plate or cleaning accessory to the trigger
mechanism. If using the jet nozzle, assemble the brush onto
the nozzle. If using an extension, attach the extension to the
trigger mechanism, then attach the accessory to the extension.
NOTE - The screw can be found in a bag down inside
the carrying handle.
NOTE - Before unscrewing the filler cap and filling
the reservoir, make sure any remaining water has
cooled for at least twenty (20) minutes. Empty any
remaining water to avoid over-filling.
NOTE - Never use more than two extensions when
using the steamer.
Never attach extensions or accessories while
unit is emitting steam.
3. Press trigger button to remove any remaining steam from
the system. Flip up filler cap lid and carefully unscrew filler
cap. Using the funnel and measuring cup, fill the steamer
with clean tap water (distilled water recommended). DO
NOT OVERFILL.
Do not look directly down
into the fill hole when
filling. Keep your free
hand and others at a safe
distance.
5. Plug in the power cord and turn the switch ON (switch light
will turn on).
face down on any surfaces. Once the switch is turned ON,
it will take about 4-12 minutes to produce steam. Once the
amber indicator light on the container turns off, you are
ready to begin steaming.
NOTE - The amber indicator light may illuminate during
usage. This is normal. If you notice a drop in steam
pressure, release trigger until the indicator light turns off
DO NOT leave steam plate unattended, or
4. Use the chart below as a guide to determine how much
water you will need based on how long you need to use
the steamer. Replace fill cap and shut filler cap lid when
filled with desired amount.
6. You can control the flow of steam from the steam plate by
activating the trigger
from the plate, the trigger can be locked into place:
a) Press and hold trigger
b) Slide the switch lock forward.
c) Slide the switch lock back to
release.
. To have a contiuous flow of steam
.
English
4
Cooling / Refilling:
ollow these steps whenever you are finished or need to refill the container.
F
1. Shut the unit OFF.
2. Activate trigger until all pressure has been released.
3. Unplug power cord.
4. Allow steamer to cool for at least twenty (20) minutes.
5. Once unit has sufficiently cooled, repeat steps 3-5 in Setup to continue. If finished steaming, drain remaining water from
the container. NEVER store the unit with water in the container.
Wallpaper Removal:
1. For best results, use a scoring tool
or a putty knife and gently score
the wallpaper in a crisscross
pattern before removal. The
perforations will allow the steam to
penetrate the wallpaper.
2. To remove wallpaper, hold the steam
plate flat against the scored wallpaper
and hold for 15-20 seconds. Move the
steam plate to a new section and
remove the steamed section with the
scraper blade.
DO NOT operate the steamer
once the water container is
empty. Make sure to wear
gloves and eye protection.
Steam Cleaning - General Notes:
Using Steam on Delicate Materials
Always check the suitability of materials before steam cleaning. Steam is being generated at temperatures in excess of 212ºF
(100ºC). Do not use on any surfaces that cannot withstand this temperature. Always test a small area of the material, preferably
an area that is normally out of view. Do not soak materials being cleaned. Only a light application of steam is required. See
below for more information on steam cleaning.
DO NOT attempt to use the steam plate included with this unit as a cleaning device. The steam plate is designed
for wallpaper removal only. This unit is not recommended to be used on self-adhesive vinyl tiles.
Pressurized steam may bounce back off cleaning surface.
• Using the cleaning accessories generally require less water than wallpaper removal. Using less water will decrease time it
takes for the unit to make steam.
• Activate the trigger as needed for sufficient steam supply. Use the soft bristles to brush away dirt, grease, unwanted dried
paint, etc.
Use only clean tap water or distilled water when using the steamer
•
• When cleaning upholstery or clothing,
view and wait 24 hours before checking whether the material has been affected. If material has been adversely affected, DO
NOT CONTINUE!
DO NOT over-scrub the surface unless you are cleaning tiles or stone.
. No detergents or any other additives are needed.
DO NOT soak the material. Try cleaning an inconspicuous area that is normally not in
5
English
Using the Cleaning Accessories:
(a)
(b)
(c)
(d)
The accessories are excellent tools for cleaning a variety of surfaces.
OTE - Using the optional accessories for cleaning generally requires less water than wallpaper removal. Using less
N
water will decrease time it takes for the unit to make steam.
The Large Cleaning Brush (a)
The large cleaning brush and towel can be used to clean large, solid areas or upholstery. It
can be used on surfaces such as ceramic, stone, parquet, marble, linoleum and carpet (see
Steam Cleaning Tips, below before cleaning).
Window / Tile squeegee (b)
The squeegee is an excellent tool for cleaning windows and also tiles. The rubber blade can
be used to scrape away dirt and other particles as steam is applied.
The Extensions (c)
The extensions can be used for floor cleaning and to help you reach into higher or harder to
reach areas.
The Jet Nozzle (d)
The jet nozzle is recommended for steam cleaning smaller, harder to reach areas.
Steam Cleaning Tips - Read before starting
Flooring and Carpeting:
• This unit is not recommended for use on surfaces that can be damaged by heat or water, such as self-adhesive vinyl tiling, or
wood flooring as the steam may cause the floor boards to swell. Always check with floor manufacturer before using steamer.
• Some carpets contain stain resistant treatments which may be affected by steam cleaning. Try cleaning a small, normally
unseen area of carpet, and allow 24 hours to verify any unusual effects on the carpet. If this occurs,
TO USE. Check with your carpet supplier for further information.
Windows and Tiles:
• Be careful not to pick up dirt or grit particles on the rubber blade as this could scratch the glass.
Antique and stained glass may be brittle and may crack under extreme temperatures.
•
• Do not use on glass when the temperature is below 32ºF (0ºC). Glass may crack in cold temperatures.
If your window has been treated or coated in any way, check with manufacturer before using steamer.
•
Upholstery and Fabrics:
Some upholstery and fabrics contain stain resistant treatments which may be affected by steam cleaning.
•
small, normally unseen area and allow 24 hours to verify any unusual effects. If this occurs, DO NOT CONTINUE TO USE.
Check with material supplier for further information.
• Always check the suitability of materials before steam cleaning. Do not use on any surfaces that cannot withstand
temperatures in excess of 212ºF (100ºC).
On clothing, always check the garmet label or check with the clothing retailer before steam cleaning.
•
• When cleaning upholstery or clothing,
oo much steam can leave water marks or other damage.
T
DO NOT soak the material. Only a small amount of steam is sufficient for cleaning.
DO NOT CONUTINUE
Try cleaning a
General:
Activate the trigger as needed for suf
•
grease, unwanted dried paint, etc.
Use only clean tap water or distilled water when using the steamer
•
Read this manual for complete instructions. Follow all warnings.
•
English
ficient steam supply. Use the soft bristles on the accessories to brush away dirt,
DO NOT over-scrub the surface unless you are cleaning tiles or stone.
. No detergents or any other additives are needed.
6
Loading...