Go to www.vtechphones.com
6
U
]K
X
O
T
M
U
T
to register your product for
enhanced warranty support
and latest VTech product news.
VM2251-2
Quick start guide
What’s in the box
VM2251-2 baby monitor system
Baby’s room Living room
Connect and power on - Baby unit Connect and power on - Parent unit
The rechargeable batter y is pre-installed in your parent unit.
The default volume of your parent unit
•
is level 3. If you experience high-pitched
screeching noise from your baby monitor
while positioning:
Make sure your baby unit and parent unit
-
are more than 1 meter (3 feet) apart, OR
Turn down the volume of your parent unit.
-
Status check
Once you power on your baby monitor, your parent unit displays image from baby unit, and the signal status can be
checked on the LCD screen.
The POWER LED light of baby units turn on.
Change different views - View
Press and then or to choose . Press to open the submenu. After that, press or to select a camera
number to enter SINGLE mode.
Switch among the
baby un it s
Change different views - Patrol
Press and then or to choose . Press to open the submenu. After that, press or to select to
enter PATROL mode to alternately view the image from one baby unit to the next one in every 10 seconds.
10s
Overview - Parent unit
LED lights
Zoom
Main screen
Power indicator
TALK
MENU/SELECT
Arrow keys and
+ / VOL / -
MIC
Battery indicator
ON/OFF
Power jack
Speaker
Stand
Overview - Baby unit
Sound-activated Screen
On
O
Basic operation - Parent unit
Microphone
Camera
Light sensor
PAIR button
Speaker
Power jack
ON/OFF
Power indicator
Basic operation - Baby unit Night vision
Adjust speaker volume
Press + / VOL / - to adjust your parent unit speaker
volume. It determines the volume of sound
transmitted from your baby units.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold TALK and speak to your parent unit.
Your voice is transmitted to the baby unit.
Sound activation
Turn off the screen
Press to enter the main menu when the parent
1.
unit is idle.
Press or to choose , then press to open
2.
the submenu.
Press or to choose the desired time period to
3.
automatically turn off screen
( / - 5 min./ - 30 min. / - 60min.), then
press to confirm your selection and return to
idle screen.
Use the menu
Press to enter the menu, choose a menuo enter the menu, choose a menu
item, or save a setting.
While in the menu:
Press or to scroll among the menu
•
options. Press to enter the desired
sub-menu.
Press or to select an an item.
•
Press to confirm your selection.
•
Turn off the parent unit
Slide ON/OFF switch to power off your parent
unit.
Turn off the baby unit
Slide the ON/OFF switch to OFF to power off your baby unit.
Mount the baby monitor (optional)
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When
the baby unit detects low light levels, the infrared
LEDs turn on automatically. The images from this
baby unit is in black and white, andunit is in black and white, and appears
on screen.
It is normal if you see a short white glare on your
•
parent unit screen as the baby unit is adapting to the
dark enviro nment.
When the i nfrared LEDs are on, t he image i s in
•
black and white. This is nor mal due to ex ternal l ight
source s.
Depending on the surroundings and other
•
interfering factors, like lightings, objects, colors and
backgrounds, the display resolution may vary. Adjust
the baby unit’s angle, or place the baby unit at a
higher level to prevent glare and blurry display.
Automatically turns on the parent unit screen when the baby
unit being viewed detects a sound after the screen is turned
off. When no sound is detected within 50 seconds, the
screen is automatically turned off to save power.
Check for reception strength and
•
camera angle before drilling the holes.
Use a pencil to mark two holes in
parallel. Make sure they are the
same distance apart as the wall
mount at the bottom of the baby unit.
Drill two holes in the wall (7/32 inch
drill bit). If you dirll the holes into a
stud, insert the screws into the holes.
Tighten the screws until only 1/4 inch
of the screws are exposed.
Align the wall mount bracket and screws
with the holes in the wall as shown.
Slide the wall mount down until it locks
into place.
Place the baby unit on the wall mount
bracket. Make sure the baby unit is fixed
on the wall.
Pan or tilt to adjust the baby unit angle.
Specifications are subject to change without notice.
© 2017 VTech Communications, Inc. All rights reserved.
10/17. VM2251-2_QSG_V1.
Document order number: 96-011937-010-100