Videx Security SL5488 User Manual
USER INSTRUCTION
Art.
SL
54
8
8
Telephone
Door release
button
:
Privacy Switch:
Privacy LED
3
:
STEP 1
STEP 2
LED4:
Bus relay button
Spare service buttons:
Red LED indicates if
privacy is on or off.
LED 1:
Talk Button LED 2:
Pressing this button after a
call is made will open the
speech path, pressing it
again will end the
conversation. Pressing the
talk button in standby will
recall the picture (press the
talk button the number of
times of the door to recall).
During a call press and hold
to speak in simplex mode,
release button to allow
speech from panel.
To activate the privacy facility (i.e.
No calls will be received).
Press and hold the button and
the button (for approx. 3
seconds). The privacy on LED3 will
illuminate.
Speech
Volume
Ring
Volume
To deactivate the privacy facility
before the time out period.
Press and hold the button and
the button (for approx. 3
seconds). The privacy on LED3 will
turn off.
Brightness
Control
Colour
Control
Press and hold this button along
with the talk button to switch
privacy on and off.
Door open LED
Pressing this during a call
will open the door. Also used
for intercommunicating
between other monitors
when in standby.
Bus relay button. To activate a bus
relay pick up the handset and press
as many times as the address value of
the relay. (Please note this relay will
not be fitted on all systems)
USER INSTRUCTION
STEP 1
STEP 2
ST
EP 3
Art.
SL
54
8
8 Telephone
An incoming call will be signalled by
an audible tone from the videophone
and the picture will appear (the
picture will only appear on extension
phone 1).
Adjusting the number of rings, privacy time and intercommunication:
Number of rings: - To program the number of rings the monitor must be in programming mode. This is achieved by
pressing the two following buttons at the same time – the left button of the volume control and the right button of
the colour intensity control. When the programming mode is entered LED1 starts flashing, this will automatically
reset after 20 seconds of idle time. When in the programming mode press and hold the button, LED1 will stop
flashing and LED2 will start to flash showing the number of rings (each flash = 1 ring, i.e. 6 flashes = 6 rings) once the
required value of rings has been reached, release the button. LED1 will start flashing again to signal that other
programming operations can be performed. After a short period with no further buttons being pressed, programming
mode will end.
Press the button once and speak
with the caller, alternatively hold the
button for 3 seconds to activate
simplex speech. Then pressing and
holding the button will allow speech
to the door and releasing it will allow
speech from the door.
To open the door press the
button. To end the call press the
button.
Privacy Operation: - Press and hold the button and the button (for approx. 3 seconds) to enable the
privacy function. LED3 next to the button illuminates and the unit emits a beep. To set the privacy duration press
and hold the button, LED 1 will stop flashing and LED 3 will start to flash showing the number of times the
button is pressed (each flash = 15 minutes i.e. 8 flashes = 2 hours). Once the duration has been reached release
the button. Wait approx 10 seconds for LED1 to stop flashing to signal that the new value is stored.
Intercommunication: - Firstly please note that extension 1 is mandatory. One extension in each apartment must
be set as extension 1. To intercommunicate with another device in the same apartment simply press the
button the number of times of the extension to call i.e. to call extension 3 press the button 3 times and wait. To
intercommunicate with another apartment (dip-switch 1 on SW3 only) simply press the button the number
of times of the phone ID to call and wait for an answer.
UISL5488 1.0
Loading...