Videx Security 6378 User Manual

6300 Series
Art.6378 3.5" hands free colour display videophone
27 mm 102 mm
182 mm
B
C
E
D
PT2
PT3
+VD
+20V1V/2V
GNDVL–LBAL
ON
ON
PT1 VR1
A
6 7 8 5 4 3 2 1
4 3 2 1
DSW1
DSW2
SW1
DOL
EXTCSWSW
12Vo
12Vi–VM
H
FG
Fig. 1
ART.6378 VX2200 6300 SERIES HANDS FREE VIDEOPHONE FOR SYSTEMS USING COMPOSITE VIDEO SIGNAL COAX OR BALANCED TWISTED PAIR
Surface mount hands free intelligent videophone incorporating a 3.5” Hi-Res full colour active matrix LCD monitor, with “answer/ camera recall”, “door open/concierge call”, “privacy” and one “service” button plus 2 LED’s one for generic use (door opening usually) and one to indicate privacy service enabled. Program­mable settings: video mode (coax or balanced), privacy dura­tion, melody and number of rings. Adjustments: call tone volume (3 levels), speech volume, pic­ture hue, contrast and brightness.
PUSH BUTTON OPERATION DURING STANDBY FIG. 1
Service button When pressed, shorts terminal “SW “ to “SW “ (max 24Vdc 50mA).
Privacy service
Press to enable the privacy service. The LED “ “ turns on. The service is deactivated by pressing again the same button or when the programmed time expires.
Call the concierge
Press to book a call to the digital concierge if installed on the system.
Camera recall
Press a number of times equal to the ID value of the door panel to switch ON. The LED “ “ turns on. When the connection is made, press again to end the call.
Fig. 2
LEGEND
A
Connection terminals
B
8 Way dip switch bank to set videophone address
C
4 Way dip switch bank to set video mode
D
Contrast adjustment trimmer
E
Hue adjustment trimmer
F
Speech volume control
G
Brightness control
H
Call tone volume switch
Art.6378 - Installation instructions
1
66251230-EN - V1.4 - 15/06/16
6300 Series
Art.6378 3.5" hands free colour display videophone
PUSH BUTTON OPERATION DURING A CALL FIG. 1
Service button When pressed, shorts terminal “SW “ to “SW “ (max 24Vdc 50mA).
Reject the call
During an incoming call, press this button to reject the call. The visitor doesn’t receive any warning of the call rejected.
Open the door
Press to activate the door open relay of the outdoor unit and end the connection. The unit emits 5 “beeps“ and the“ “ LED will ash, then returns to stand-by mode.
Answer a call
Press to answer the call and start the conversation. The“ “ LED turns on.
PUSH BUTTON OPERATIONS DURING A CONVERSATION FIG. 1
Service button When pressed, shorts terminal “SW “ to “SW “ (max 24Vdc 50mA).
Open the door
Press to activate the door open relay of the outdoor unit and end the connection after 10 seconds. The unit emits 5 “beeps“ and the“ “ LED will ash, then returns to stand-by mode.
End conversation
Press to end a call. The“ “ LED turns o.
Simplex button.
Pressing and holding the button for more than 3 seconds will switch the videomonitor into SIMPLEX speech mode. Press and hold the button to speak to the caller ( LED will ash rapidly), release the button to listen ( for 10 seconds the videomonitor will switch o. The videomonitor will revert to duplex speech when another call is made.
LED will ash slowly). If the button is not pressed
LEDS FIG. 1
Privacy on LED.
LED
LED
LED
PROGRAMMING
All programming options are available only when the system is in stand-by.
PRIVACY SERVICE DURATION
1. Press and keep pressed “ and the unit emits a “beep“;
2. Press “ “ button as many times as required. Each press is equal to 15 minutes: the unit emits a “beep“ every time the button is pressed. I.E.: press 4 times for 1 hour, 12 for 3 hours. Default: innite. Max value: 20 hours. To program innite privacy time don’t press any buttons;
3. Wait for some seconds: the “ “ LED turns o and the unit emits a “beep“ that conrms the new setting is properly stored;
4. The unit returns to stand-by mode.
It illuminates when the privacy service is enabled, when pressing the service button or during programming mode.
Generic use LED.
It is controlled from the terminal “DOL”. Normally used to signal the door status (open or closed).
ON LED.
It illuminates when the videophone is switched ON or ashes quickly in “Push To Talk“ mode.
“ button for 10 seconds to enter privacy service duration programming mode: the “ “ LED turns on
CONTROLS FIG. 1 AND FIG. 2
Speech volume control
VR1
(sliding wheel). Call tone volume switch
SW1
(3 levels). Brightness control
PT1
(sliding wheel).
PT2
PT3
Hue adjustment trimmer (rotate left to increase or right to decrease).
Contrast adjustment trimmer (rotate left to increase or right to decrease).
MELODY TYPE
1. Press and keep pressed “ and then a “beep“;
2. After the “beep” press “ “ buttons to select the next melody: a new melody will play for some seconds then the unit emits a “beep“. There are 9 melodies available. Note: press “ “ buttons only after the melody is over and the unit emits the “beep“;
3. When desired melody is playing, wait for some seconds: the unit completes the melody and emits a “beep”, then the unit emits a dou­ble “beep“ that conrms the new setting is properly stored;
4. The unit returns to stand-by mode.
Note: To set the melody it is required that the videophone is connected in a system where the +20Vdc voltage from Art.893N1 is always enabled.
Art.6378 - Installation instructions
“ button for 10 seconds to enter melody type programming mode: the unit plays the current melody
2
66251230-EN - V1.4 - 15/06/16
6300 Series
Art.6378 3.5" hands free colour display videophone
NUMBERS OF RINGS
1. Press and keep pressed “ unit emits a “beep“;
2. Press “ “ button as many rings as required: the unit emits a “beep“ every time the button is pressed. I.E.: press 3 times for 3 rings. Default value: 6 rings. Max value: 9 rings;
3. Wait for some seconds: the “ “ LED turns o and the unit emits a “beep“ that conrms the new setting is properly stored;
4. The unit returns to stand-by mode.
VIDEO MODE SW2
The video mode setup is carried out by the 4 way Dip-Switch accessible from the rear side of the videophone.
Switches 3 and 4 adjust the video signal impedance. When using more than one videomonitor in parallel (without a video splitter) put both switches in the OFF position on all but the last videomonitor (end of line).
“ button for 10 seconds to enter numbers of rings programming mode: the “ “ LED turns on and the
VIDEO MODE
Switches 1,2 Mode
Coax
Balanced
VIDEOMONITOR/INTERCOM ADDRESS, VIDEO MODE AND TERMINATION SETUP DSW1
Each intercom is addressed in binary (PHONE ID) using the 8 way dipswitches located on the rear of the unit. Each switch corre­sponds to one bit which can have a value 0 (OFF) or 1 (ON). Each bit corresponds to a decimal weight depending on the position: Switch 1 = decimal 1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. I.E. to set the address 37, put switches 1, 3 and 6 on (1+4+32=37).
SWITCHES DECIMAL WEIGHT ADDRESS
8 7 6 5 4 3 2 1 128 64 32 16 8 4 2 1
OFF OFF OFF OFF OFF OFF OFF ON 0 0 0 0 0 0 0 1 1 OFF OFF OFF OFF OFF OFF ON OFF 0 0 0 0 0 0 1 0 2 OFF OFF OFF OFF OFF OFF ON ON 0 0 0 0 0 0 1 1 3 OFF OFF OFF OFF OFF ON OFF OFF 0 0 0 0 0 1 0 0 4
OFF OFF ON OFF OFF ON OFF ON 0 0 1 0 0 1 0 1 37
ON OFF ON ON OFF ON OFF OFF 1 0 1 1 0 1 0 0 180
75 OHM VIDEO TERMINATION
Switches 3,4 Termination
Enabled
Disabled
CABLING 6378 USING CAT.5 CABLE* Connections:
• One pair must be used to double up the BUS line “L”;
• One pair must be used to double up the power supply ground. The bus ground
must be connected with power supply ground (“GNDV” & “–”);
• One pair must be used to double up the positive power supply +20V;
• One pair must be used for the video signals “V1” and “V/V2”;
• A link is required between “12Vo” & “12Vi”;
• An additional PSU Art.893N1 is required every 50 videomonitors installed in the system.
Max Distance**: 70 metres. System type: Audio/video door entry systems.
* When this cable is used, in case more videophones are connected in parallel in the same apartment, a local power supply for additional videophones is required. ** By max distance we mean the maximum distance between the door panel and the furthest videophone/intercom
3
Art.6378 - Installation instructions
66251230-EN - V1.4 - 15/06/16
6300 Series
Art.6378 3.5" hands free colour display videophone
ART.6378  SIGNALS
+VD
V/V2
GNDV Video power supply ground reference
DOL 12Vdc input to supply Aux LED
EXTC Call tone output for extension sounder (Art.512A)
12Vo +12Vdc stabilized output
12Vi Stand-by +12Vdc power supply input
12Vdc output to supply coax video distributor Art.894N
+20 Video power supply 17÷20Vdc
V1 Balanced video signal V1 sync. (balanced video signal mode)
Balanced video signal V2 sync. (balanced video signal mode) Composite video signal (coax video signal mode)
L BUS line – BUS line ground reference
LB Local bell input (active low) AL Alarm input (active low)
SW Service button connection SW Service button connection
Power supply ground input / coax video ground
Auxiliary input 200mA 12Vdc for video memory
VM
(Art.6378/MV)
Max 24 Vdc
50mA
TECHNICAL SPECIFICATION Working Voltage: 17÷20Vdc
Power Consumption: Standby: 10mA
During a conversation: 150mA Max: 250mA Working Temperature: -10°C +50°C
Art.6378 - Installation instructions
4
66251230-EN - V1.4 - 15/06/16
6300 Series
224kvd119.dw
g
Art.6378 3.5" colour display videophone
Address N.3
Address N.1
13V
ART.521B
115
0
Art.6378
Art.6378
+
swsw
ON/OFF
Art.6378
Address N.4
It is required an additional power supply for videophones with memory board. For Art.6378/MV it is required 1 AMR2-12 each 8 videophones with memory board
Art.AMR2-12
12Vdc
Art.6378/MV
Address N.2
+B
ART.893N1
0
Art.4202RV
coax
B.V.
SE
12Vac
GND
Titolo:
Videx Electronics S.p.A.
Via del Lavoro 1, 63846 Monte Giberto (FM)
Phone: +39 0734 631669 - Fax +39 0734 631669
www.videx.it - info@videx.it
Notes:
Note:
Art.6378 - Installation instructions
+12
_
L
BSSLNCCNO
A
316x
V1
V2 / V
TRD
GNDV
PTE
12T
others
Foglio
Data creazione:Title:
11/03/2015
11
Data modifica:
10/11/2015
Autore:
Marco Rongoni
Cod.File:
/
5
66251230-EN - V1.4 - 15/06/16
6300 Series
224kvd120.dw
g
Art.6378 3.5" colour display videophone
Address N. 3
Address N. 1
13V
ART.521B
115
0
Art.6378
Art.6378
+
swsw
ON/OFF
Art.6378
Address N. 4
Art.6378
Address N. 2
+B
ART.893N1
0
Unit ID:
Art.4283-1
blu giallo
1C
Art.4845
Titolo:
Videx Electronics S.p.A.
Via del Lavoro 1, 63846 Monte Giberto (FM)
Phone: +39 0734 631669 - Fax +39 0734 631669
www.videx.it - info@videx.it
Notes:
Note:
Art.6378 - Installation instructions
1
Dry Contact Relay
87465321ON109
Relè a contatti puliti
Unit ID:
12Vac
6
5
4
SE
3
Art.4283-1
1
2
1
12Vac
87465321ON109
12Vac
SE
Data creazione:Title:
Foglio
13/03/2015
11
Data modifica:
06/07/2015
Autore:
Marco Rongoni
Cod.File:
/
6
66251230-EN - V1.4 - 15/06/16
6300 Series
www.videx.it - info@videx.it
228kvd001a.dw
g
Art.6378 3.5" colour display videophone
Art.6378
Address N.3
Art.6378
Address N.1
Art.6378
Address N.4
Art.6378
Address N.2
ART.893N1
0
Titolo:
Videx Electronics S.p.A.
Via del Lavoro 1, 63020 Monte Giberto (AP)
Phone: +39 0734 631669 - Fax +39 0734 631669
Notes:
Note:
Art.6378 - Installation instructions
13V
ART.521B
115
0
Art.8844
h g f e d c b a
8 7 6 5 4 3 2 1
1
8203-0
BALANCE
Art.8830
87342 5 6
1
ON
NO
C NC SL BS
L
+12 Gnd
Coax
NC
12Vac
SE
+B
+
swsw
2
3
4
Foglio
Data creazione:Title:
13/03/2015
11
Data modifica:
17/03/2015
Autore:
Marco Rongoni
Cod.File:
/
7
66251230-EN - V1.4 - 15/06/16
6300 Series
www.videx.it - info@videx.it
228kvd013b.dw
g
Art.6378 3.5" colour display videophone
Art.6378
Address N.3
Art.6378
Address N.1
Art.6378
Address N.4
Art.6378
Address N.2
Titolo:
Videx Electronics S.p.A.
Via del Lavoro 1, 63846 Monte Giberto (FM)
Phone: +39 0734 631669 - Fax +39 0734 631669
Notes:
Note:
Art.6378 - Installation instructions
Art.8202-8202R
Art.8830
BALANCE
ART.893N1
0
+B
ART.521B
sw
1150 sw +
Coax
NC
SE
12Vac
Foglio
Data creazione:Title:
13/03/2015
11
Data modifica:
06/07/2015
Autore:
Marco Rongoni
Cod.File:
/
8
66251230-EN - V1.4 - 15/06/16
6300 Series
6300 Series Wall mounting instructions
D
Fig. 1
2
1
Fig. 2
135cm
E
C
Fig. 3
C
F
A
B
F
A
B
2
1
Fig. 4
1. In order to install the videophone, it is necessary to remove the cover, which contains all the electronics, from the base: press
lightly on the bottom part of the videophone and simultaneously pulling outwards the upper part as shown in Fig. 1.
2. Put the base of the unit on the wall at approx 135cm from the nished oor to match the points for the xing holes “A” (Fig. 2) remembering that the wires “D” (Fig. 3) must be fed through the large hole “E” (Fig. 3). If you use the ush mounting box 503, embed it into the wall vertically at approx. 140cm from the nished oor and the base.
3. Following Fig. 3, make the holes “A”, insert the wall plugs “B” and x the base with the screws “C” feeding the wires “D” through the hole “E”. If you have used the box 503, x the base to the wall through the holes “F” using the screws “C”.
4. As shown in Fig. 4, connect the wires to the removable terminals following the provided installation diagram. Connect the terminal blocks to the electronics contained in the cover as shown in Fig. 5. Test system before closing. Contrast and hue trimmers can be adjusted only if the videophone is open. To activate the display and see changes use the “Camera Recall” function by pressing
Note: while testing the system, it is advisable to hold the cover with your hand.
5. Once testing is complete and all the necessary adjustments are made, close the unit as shown in Fig. 6: rst hook in the bottom and the then the top until you hear a click.
Fig. 5
button.
Fig. 6
Art.6378 - Installation instructions
9
66251230-EN - V1.4 - 15/06/16
6300 Series
Note
Art.6378 - Installation instructions
10
66251230-EN - V1.4 - 15/06/16
6300 Series
Note
Art.6378 - Installation instructions
11
66251230-EN - V1.4 - 15/06/16
MANUFACTURER
The product is CE marked demonstrating its conformity and is for distribution
VIDEX ELECTRONICS S.P.A.
Via del Lavoro, 1 - 63846 Monte Giberto (FM) Italy Tel (+39) 0734 631669 - Fax (+39) 0734 632475 www.videx.it - info@videx.it
CUSTOMER SUPPORT
All Countries:
VIDEX ELECTRONICS S.P.A.
www.videx.it - technical@videx.it Tel: +39 0734-631669 - Fax: +39 0734-632475
UK Customers:
VIDEX SECURITY LTD
www.videx-security.com Tech Line: 0191 224 3174 - Fax: 0191 224 1559
Main UK oce:
VIDEX SECURITY LTD
1 Osprey Trinity Park Trinity Way LONDON E4 8TD Phone: (+44) 0870 300 1240 Fax: (+44) 020 8523 5825 www.videx-security.com marketing@videx-security.com
Greece oce:
VIDEX HELLAS Electronics
48 Filolaou Str. 11633 ATHENS Phone: (+30) 210 7521028 (+30) 210 7521998 Fax: (+30) 210 7560712 www.videx.gr videx@videx.gr
Northern UK oce:
VIDEX SECURITY LTD
Unit 4-7 Chillingham Industrial Estate Chapman Street NEWCASTLE UPON TYNE - NE6 2XX Tech Line: (+44) 0191 224 3174 Phone: (+44) 0870 300 1240 Fax: (+44) 0191 224 1559
Danish oce:
VIDEX DANMARK
Hammershusgade 15 DK-2100 COPENHAGEN Phone: (+45) 39 29 80 00 Fax: (+45) 39 27 77 75 www.videx.dk videx@videx.dk
Benelux oce:
VIDEX BENELUX
E3 Iaan, 93 B-9800 DEINZE Phone: (+32) 9 380 40 20 Fax: (+32) 9 380 40 25 www.videxbenelux.be info@videxbenelux.be
within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU (LVD); 2011/65/EU (RoHS): CE marking 93/68/EEC.
Loading...