Videx Security 6276 User Manual

6200 Series
Art.6276 3.5" colour display videophone
27 mm 144 mm
182 mm
+VD
+20
V1
V/V2
ENG
A
L
LB
GNDV
AL
SW
SW
DOL
EXTC
DSW1 DSW2
I
B
Fig. 1
ART.6276 VX2200 6200 SERIES VIDEOPHONE FOR SYSTEMS USING COMPOSITE VIDEO SIGNAL COAX OR BALANCED TWISTED PAIR
DESCRIPTION
Surface mount videophone incorporating a 3.5” Hi-Res full col­our active matrix LCD monitor, with “camera recall”, “door open/ concierge call”, “service” and “privacy” button. 2 LED’s one for generic use (door opening usually) and one to indicate privacy service enabled. Programmable settings: privacy duration, video mode (coax or balanced), melody and number of rings. Adjustments: call tone volume (3 levels), microphone volume, picture hue, contrast and brightness.
D
PT1
G
F
VR1
Fig. 2
PT2
PT3
E
SW2
LEGEND
A
Connection terminals
B
8 Way dip switch bank to set videophone address
C
4 Way dip switch bank to set video mode
D
Contrast adjustment trimmer
E
Hue adjustment trimmer
F
Microphone volume adjustment trimmer
G
Brightness control sliding wheel
H
Call tone volume switch
I
RJ-45 connector
C
H
PUSH BUTTONS
Service button When pressed, shorts terminal SW to SW (Max 24 Vdc 50mA).
Privacy service
Press to enable the privacy service. The LED turns on. The service is deactivated by pressing again the same but­ton or when the programmed time expires.
Door Open Push Button
• During a conversation, operation of this button will release the door from where the call originated. This will be
conrmed by an acoustic tone. If terminal DOL is connected, the “door open” LED under the symbol will also illuminate.
• When the system is in stand-by, picking up the handset and pressing the buttons will book a call to the concierge (If available).
Camera recall
When the system is in standby (no calls on the system), pick up the handset then press this button to open the SPEECH/VIDEO to the door station. Press as many time as the ID value of the door panel to connect to.
Art.6276 - Installation instructions
1
66251125-EN - V1.2 - 31/10/16
6200 Series
Art.6276 3.5" colour display videophone
LEDS FIG. 1
Privacy on LED
LED
LED
PROGRAMMING
The programmable settings are:
• Privacy service duration (from 15 minutes to 20 hours or innte);
• Melody (9 available);
• Number of rings (3 or 6);
• Video mode (coax or balanced);
• Videophone address (Phone ID).
It illuminates when the privacy service is enabled, when pressing the service button or during pro­gramming mode.
Generic use LED
It is controlled from the terminal DOL. Normally used to signal the door status (open or closed).
CONTROLS FIG. 1 AND FIG. 2
Contrast adjustment trimmer*
PT1
PT2
VR1
Rotate anticlockwise to increase or clockwise to decrease.
*Not available in some LCD versions.
Hue adjustment trimmer
Rotate anticlockwise to increase or clockwise to decrease.
Microphone volume adjustment trimmer
Rotate anticlockwise to decrease or clockwise to increase.
Brightness control sliding wheel
PT3
Rotate anticlockwise to increase or clockwise to decrease (when videophone is closed).
Call tone volume switch
SW2
3 levels: low, medium and high.
TO SET PRIVACY SERVICE DURATION
1. Press and keep pressed the unit emits a “beep“;
2. Press button as many times as required. Each press is equal to 15 minutes: the unit emits a “beep“ every time the button is pressed. I.E.: press 4 times for 1 hour, 12 for 3 hours. Default: innite. Max value: 20 hours. To program innite privacy time don’t press any buttons;
3. Wait for some seconds: the LED turns o and the unit emits a “beep“ that conrms the new setting is properly stored;
4. The unit returns to stand-by mode.
TO SET MELODY
1. Press and keep pressed button for 10 seconds until the unit plays the current programmed melody and emits a “beep” at the end.
2. Press again button to listen to the available melodies (maximum 9);
3. Once the selected melody has been reached, wait 5 seconds for a “beep”;
4. The new melody will be stored.
Note: To set the melody it is required that the videophone is connected in a system where the +20Vdc voltage from Art.893N1 is always enabled.
TO SET THE NUMBER OF RINGS 6 OR 3:
Default setting is 6, to set 3 proceed as follows:
1. Turn o the videophone by unplugging the connector from the PCB;
2. Make a short between terminals GNDV and LB on the connector;
3. Plug the connector in and wait for a beep before removing the short;
4. To go back to 6 rings, do the same but two “beeps” will be emitted.
button for 10 seconds to enter privacy service duration programming mode: the LED turns on and
Art.6276 - Installation instructions
2
66251125-EN - V1.2 - 31/10/16
6200 Series
Art.6276 3.5" colour display videophone
TO SET THE VIDEO MODE AND TERMINATION
The videophone can operate with either composite video signal (coax cable) or balanced video signal (two wires). Switches 1 & 2 of DSW2 are used to set video mode while switches 3 & 4 are for video termination.
VIDEO MODE  DSW2
Switches 1,2 Mode
Coax
Balanced
Switches 3 and 4 adjust the video signal impedance. when using more than one videomonitor in parallel (without a video splitter) put both switches in the OFF position on all but the last videomonitor (end of line).
VIDEOMONITOR/INTERCOM ADDRESS, VIDEO MODE AND TERMINATION SETUP DSW1
Each intercom is addressed in binary (PHONE ID) using the 8 way dipswitches located on the rear of the unit. Each switch corre­sponds to one bit which can have a value 0 (OFF) or 1 (ON). Each bit corresponds to a decimal weight depending on the position: Switch 1 = decimal 1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. I.E. to set the address 37, put switches 1, 3 and 6 on (1+4+32=37).
SWITCHES DECIMAL WEIGHT ADDRESS
8 7 6 5 4 3 2 1 128 64 32 16 8 4 2 1
OFF OFF OFF OFF OFF OFF OFF ON 0 0 0 0 0 0 0 1 1 OFF OFF OFF OFF OFF OFF ON OFF 0 0 0 0 0 0 1 0 2 OFF OFF OFF OFF OFF OFF ON ON 0 0 0 0 0 0 1 1 3 OFF OFF OFF OFF OFF ON OFF OFF 0 0 0 0 0 1 0 0 4
75 OHM VIDEO TERMINATION  DSW2
Switches 3,4 Termination
Enabled
Disabled
OFF OFF ON OFF OFF ON OFF ON 0 0 1 0 0 1 0 1 37
ON OFF ON ON OFF ON OFF OFF 1 0 1 1 0 1 0 0 180
CONNECTION TERMINALS SIGNALS
12Vdc output to supply coax video distributor
+VD
Art.894N
+20 Video power supply 17÷20Vdc
Balanced video signal V1 sync. (balanced video signal
V1
mode) Balanced video signal V2 sync. (balanced video signal
V/V2
GNDV Video power supply ground reference
EXTC Call tone output for extension sounder (Art.512A)
mode) Composite video signal (coax video signal mode)
L BUS line – BUS line ground reference
LB Local bell input (active low) AL Alarm input (active low)
DOL 12Vdc input to supply Aux LED
SW
Service button connection
SW
Max 24 Vdc
50mA
TECHNICAL SPECIFICATION Working Voltage: 17÷20Vdc
Power Consumption: 200mA during a call
120mA during a conversation Working Temperature: -10°C +50°C
Art.6276 - Installation instructions
3
66251125-EN - V1.2 - 31/10/16
6200 Series
CUSTOMER SUPPORTMANUFACTURER
VIDEX ELECTRONICS S.P.A.
Via del Lavoro, 1 - 63846 Monte Giberto (FM) Italy Tel (+39) 0734 631669 - Fax (+39) 0734 632475 www.videx.it - info@videx.it
The product is CE marked demonstrating its conformity and is for distribution
Art.6276 3.5" colour display videophone
USING RJ45 PLUG TO CONNECT THE VIDEOPHONE EIA/TIA568B
8 7 6 5 4 3 2 1
BR br
G b B g O o
EIA/TIA-568B
o O g B b
O br BR
EIA/TIA568A
8 7 6 5 4 3 2 1
BR br
O b B o G g
EIA/TIA-568A
g
G
o
B
b
O br BR
NOTE: DO NOT USE CROSS OVER CABLES.
IMPORTANT NOTE: SOLID COPPER CABLES MUST BE USED. COPPER COATED STEEL CCS AND COPPER COATED ALUMINIUM CCA CAN NOT BE USED ON THE SYSTEM.
MEMORY BOARD
This device is also available in the version with memory board (Art.6276/VM). If you have that version, please refer to the “6200, 6300, 6400 and 6700 Series Memory Board” user manual for installation and use. The manual is available for download at the following link:
https://www.dropbox.com/s/492p16btyqhxmpu/66250782-EN.pdf?dl=0
RJ-45 pin VX2200 Signal
1
1 and 2 (white-orange / orange) L
2 3
3 and 4 (white-green / blue)
4 5 6
5 and 6 (white-blue / green) +
7 8
7 (white-brown) V1 8 (brown) V2
RJ-45 pin VX2200 Signal
1
1 and 2 (white-green / green) L
2 3
3 and 4 (white-orange / blue)
4 5 6
5 and 6 (white-blue / orange) +
7 8
7 (white-brown) V1 8 (brown) V2
Art.6276 - Installation instructions
All Countries:
VIDEX ELECTRONICS S.P.A.
www.videx.it - technical@videx.it Tel: +39 0734-631669 Fax: +39 0734-632475
within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU (LVD); 2011/65/EU (RoHS): CE marking 93/68/EEC.
4
UK Customers:
VIDEX SECURITY LTD
www.videx-security.com Tech Line: 0191 224 3174 Fax: 0191 224 1559
66251125-EN - V1.2 - 31/10/16
6200 Series
Art.6276 3.5" colour display videophone
Art.6276 - Installation instructions
5
66251125-EN - V1.2 - 31/10/16
6200 Series
www.videx.it - info@videx.it
224KVD139A.dwg
Art.6276 3.5" colour display videophone
BALANCED
ON
SW2 SW1
ON
123456781234
13V
ART.521B
115
0
Art.6276
Address N. 3
+
swsw
ON/OFF
Address N. 1
+B
ART.893N1
Art.6378
0
L
-
V1
LB
+20
+VD
AL
V/V2
GNDV
­VM
SW
SW
12Vi
DOL
12Vo
EXTC
Art.6778
Address N.
A
L - + - V1V2
SW2 SW1
Art.6778
Address N.
VID
C
L-+-
V1V2
4
BALANCED
ON
ON
123456781234
L
-
V1
LB
+20
+VD
AL
V/V2
GNDV
­VM
SW
SW
12Vi
DOL
12Vo
EXTC
2
2
1.50mm21.50mm21.50mm21.50mm21.00mm21.00mm
L - + - V1 V2
SE
12Vac
Title:
Titolo:
Videx Electronics S.p.A.
Via del Lavoro, 1 - 63846 Monte Giberto (FM)
Phone: +39 0734 631669 - Fax +39 0734 631669
Notes:
Note:
Art.6276 - Installation instructions
Art.4202RV
coax
B.V.
_
+12
GND
A
SL
L
BS
NCCNO
GNDV
PTE
12T
others
316x
V1
V2 / V
TRD
1/2
Data creazione:
Foglio
16/09/2016
Data modifica:
20/10/2016
Autore:
Marco@videx.it
Cod.File:
6
66251125-EN - V1.2 - 31/10/16
/
11
6200 Series
Art.6276 3.5" colour display videophone
L - + - V1V2
VID
OClose
L-+-
V1V2
Art.6276
Address N. 11
Art.6378
Address N. 9
Art.6276
Address N. 12
A
Art.6378
L - + - V1V2
VID
C
L - + - V1V2
Address N. 10
Art.6276
Address N. 7
Art.6276
Address N. 5
A = MAX 40mt
Art.6276 - Installation instructions
Art.6276
Address N. 8
MAX 400mt
A
Art.6276
L-+-
V1V2
VID
C
L - + - V1V2
Address N. 6
2/2
7
66251125-EN - V1.2 - 31/10/16
6200 Series
B
6200 Series Videophone wall mounting instructions
2
D
C
A
Fig. 1
A
1
B
A
B
Fig. 2
F
E
F
135cm
C
Fig. 3
2
G
1
Fig. 4
1. In order to install the videophone, it is necessary to remove the cover, which contains all the electronics, from the base: rstly disconnect the handset from the videophone (by removing its plug from the videophone), then press lightly the bottom part of the videophone and simultaneously pulling outwards the upper part as shown in Fig. 1.
2. Put the base of the unit on the wall at approx 135cm from the nished oor to mark the points for the xing holes “A” (Fig. 2) remembering that the wires “D” (Fig. 3) must be fed through the hole “E” (Fig. 3). If you use the ush mounting box 503, embed it into the wall vertically at approx. 140cm from the nished oor and the base.
3. Following Fig. 3, make the holes “A”, insert the wall plugs “B” and x the base with the screws “C” feeding the wires “D” into the hole “E”. If you have used the box 503, x the base to the wall through the holes “F” using the screws “C”.
4. As shown in Fig. 4A, connect the wires to the removable terminals following the provided installation diagram. Connect the ter­minal blocks to the electronics contained in the cover as shown in Fig. 4B. Reinsert the handset and test system before closing.
Note: Contrast and hue trimmers can be adjusted only if the videophone is open. Note while testing the system, it is advisable to hold the cover with your hand closing manually the hook switch of the handset (see Fig. 4B reference “G”).
5. Once testing is complete and all the necessary adjustments are made, disconnect the handset from the cover and close the unit as shown in Fig. 5: rst hook it on the bottom then push in the top until you hear the clip.
6. Reconnect the handset and hang it as shown in Fig. 6.
Fig. 5
Fig. 6
Art.6276 - Installation instructions
8
66251125-EN - V1.2 - 31/10/16
Loading...