Uniden BCD396XT remote commands

REMOTE COMMAND

【 Remote Communication Format 】

BPS rate : 4800/9600/19200/38400/57600/115200 bps Start/Stop bit : 1 bit, 1 bit Data Length : 8 bit Parity Check : None Code : ASCII Flow Control : None Return Code : Carriage Return only

【 FORMAT OF THIS DOCUMENT 】

<COMMAND NAME> Summary explanation of the function of the command

Controller → Radio Command format

Radio → Controller Response format

NOTE

1. Commands are required to wait a response from the scanner, then, next command is accepted.

2. All memory access commands are acceptable in only Program Mode.

Use PRG command to enter Program Mode, and EPG command to exit.

3. Error messages aren’t described for each command, but the scanner returns error message to the controller

as follows.

1) Command format error / Value error : ERR[\r]

2) The command is invalid at the time : NG[\r]

3) Framing error : FER[\r]

4) Overrun error : ORER[\r]

4. [\r] means "to hit the Enter key" or "to send the Return code".

5. Several commands or responses with long format are described like multi-line because of the page width

but their formats are only single line, actually.

In set command, only "," parameters are not changed.

6. The set command is aborted if any format error is detected.

7. [INDEX] or [xxx_INDEX] is the index of internal memory chain.

Dynamic Memory Allocation Structure always uses it as a handle to access data and to trace forward/reverse or up/down index. The range of the index is from 1 to maximum memory block (about 45000).

8. [FRQ], [BASEx] and [LIMIT_x] are frequency format.

It is showed by 8 digit number without decimal point. The order of the digits is from 1 GHz digit to 100 Hz digit. ex. 08510125 means 851.0125MHz

9. [TGID] shows TGID format. The formats depend on Trunked System Type.

See another Appendix to get further information.

10. [NAME] shows each custom name. If you set only a space character, the name will return to

default name.

11. [LATITUDE] shows North or South Latitude.

The data shows “DDMMSSssL” at DMS Format.

DD : Degree ( 00 - 90 : Double figure fixation ) MM : Minute ( 00 - 59 : Double figure fixation ) SSss : Second ( SS : 00 - 59 : Double figure fixation )

( ss : 00 - 99 : Double figure fixation )

L : Bearing ( N : North / S : South ) ex ) “North Latitude 40°42’51.12” shows “40425112N”.

220

12. [LONGITUDE] shows West or East Longitude.

No.

Category

Command

Function

Program Mode Only

Remote Control

GID

Get Current TalkGroup ID Status

KEY

Push KEY

POF

Power Off

QSH

Go to quick search hold mode

QSC

Set current frequency and get reception status

CSC

Go to Custom search and get reception status

PWR

Get RSSI Level

STS

Get Current Status

GLG

Get Reception Status

JPM

Jump Mode

JNT

Jump to Number Tag

MNU

Menu Mode

System Information MDL

Get Model Info

VER

Get Firmware Version

Program Control Mode PRG

Enter Program Mode

EPG

Exit Program Mode

System Settings

BLT

Get/Set Backlight

O BSV

Get/Set Battery Info

O COM

Get/Set COM port setting

O CLR

Clear All Memory

O KBP

Get/Set Key Beep and setting

O OMS

Get/Set Opening Message

O PRI

Get/Set Priority Mode

O AGV

Get/Set Auto Gain Control

O SCT

Get System Count

O

Scan Settings

SIH

Get System Index Head

O SIT

Get System Index Tail

O QSL

Get/Set System/Site Quick Lockout

O QGL

Get/Set Group Quick Lockout

O CSY

Create System

O DSY

Delete System

O SIN

Get/Set System Info

O TRN

Get/Set Trunk Info

O AST

Append Site

O SIF

Get/Set Site Info

O MCP

Get/Set Motorola Custom Band Plan

O ABP

Get/Set APCO-P25 Band Plan

O

The data shows “DDDMMSSssL” at DMS Format.

DDD : Degree ( 000 - 180 : Triple figure fixation ) MM : Minute ( 00 - 59 : Double figure fixation ) SSss : Second ( SS : 00 - 59 : Double figure fixation )

( ss : 00 - 99 : Double figure fixation )

L : Bearing ( W : West / E : East ) ex ) “West Longitude 74°00’23.05” shows “074002305W”.

Remote Command List

221

TFQ

Get/Set Trunk Frequency Info

O AGC

Append Channel Group

O AGT

Append TalkGroup ID Group

O DGR

Delete Group / Site

O GIN

Get/Set Group Info

O ACC

Append Channel / Trunk Frequency

O ACT

Append TalkGroup ID

O DCH

Delete Channel

O CIN

Get/Set Channel Info

O TIN

Get/Set TalkGroup ID Info

O GLI

Get Lockout TalkGroup ID (for Rvw L/O ID)

O SLI

Get Search L/O TalkGroup ID

O ULI

Unlock TalkGroup ID (for Rvw L/O ID)

O LOI

Lockout ID (TalkGroup ID)

O REV

Get Rev Index

O FWD

Get Fwd Index

O RMB

Get Remains of Memory Block

O MEM

Get Memory Used

O

Location Setting

LIH

Get Location Alert System Index Head

O LIT

Get Location Alert System Index Tail

O CLA

Create Location Alert System

O DLA

Delete Location Alert System

O LIN

Get/Set Location Alert System Info

O

Search / Close Call Settings

SCO

Get/Set Search/Close Call Settings

O

BBS

Get/Set Broadcast Screen Band Settings

O SHK

Get / Set Search Key Settings

O GLF

Get Global Lockout Freq

O ULF

Unlock Global L/O

O LOF

Lock Out Frequency

O CLC

Get/Set Close Call Settings

O Service Search Settings

SSP

Get/Set Service Search Settings

O

Custom Search Settings

CSG

Get/Set Custom Search Group

O

CBP

Get/Set C-Ch Only Custom search MOT Band Plan

O CSP

Get/Set Custom Search Settings

O

Weather Settings WXS

Get/Set Weather Settings

O SGP

Get/Set SAME Group Settings

O Tone-Out Setting

TON

Get/Set Tone-Out Settings

O LCD Contrast Settings

CNT

Get/Set LCD Contrast Settings

O Scanner Option Settings

SCN

Get/Set Scanner Option Settings

O Volume Level Settings

VOL

Get/Set Volume Level Settings

Squelch Level Settings

SQL

Get/Set Squelch Level Settings

APCO Data Settings

P25

Get/Set APCO Data Settings

Default Band Coverage Settings

DBC

Get/Set Default Band Coverage Settings

O GPS Settings

GDO

Get/Set GPS Format

O Band Scope Settings

BSP

Get/Set Band Scope Settings

O

IF exchange list Settings GIE

Get Global IF exchange Frequency

O CIE

Clear IF exchange Frequency

O RIE

Register IF exchange Frequency

O

TEST BAV

Get Battery Voltage

WIN

Get Window Voltage

222

<COMMAND GID> Get Current TGID Status

Controller → Radio GID[\r]

Radio → Controller GID,[SITE_TYPE],[TGID],[ID_SRCH_MODE],[NAME1],[NAME2],[NAME3][\r]

[SITE_TYPE] : Site Type

CNV : CONVENTIONAL system site MOT : MOTOROLA system site EDC : EDACS Narrow / Wide system site EDS : EDACS SCAT system site LTR : LTR system site P25S : P25 STANDARD system site P25F : P25 One Frequency TRUNK system site

[TGID] : TGID

[ID_SRCH_MODE] : ID SCAN / ID SEARCH Mode 0:ID SCAN Mode / 1:ID SEARCH Mode ) [NAME1] : SYSTEM / SITE NAME (Alpha Tag) [NAME2] : GROUP NAME (Alpha Tag) [NAME3] : TGID NAME (Alpha Tag)

FUNCTION This command return TGID currently displayed on LCD. If you get the TGID once, the scanner returns ,,,,,[\r] until next reception.

NOTE : This command return ,,,,,[\r], when TGID is not displayed.

223

<COMMAND KEY> Push KEY

Controller → Radio KEY,[KEY_CODE],[KEY_MODE][\r]

Radio → Controller KEY,OK[\r]

[KEY_CODE] M : MENU F : FUNC H : HOLD S : SCAN/SEARCH L : L/O 1 : 1 2 : 2 3 : 3 4 : 4 5 : 5 6 : 6 7 : 7 8 : 8 9 : 9 0 : 0 .(dot) : ./NO E : E/YES > : VFO RIGHT * Set "P" to KEY_MODE. < : VFO LEFT * Set "P" to KEY_MODE. ^ : VFO PUSH P : POWER/LIGHT/LOCK

[KEY_MODE] P : Press L : Long Press H : Hold (Press and Hold until Release receive) R : Release (Cancel Hold state)

Ex.1) Press MENU KEY → KEY,M,P[\r] ← OK[\r]

Ex.2) Press F + SCAN KEY → KEY,F,P[\r] : Hold F KEY ← OK[\r] → KEY,S,P[\r] : Press SCAN KEY (F + SCAN KEY operation) ← OK[\r] → KEY,F,P[\r] : Release F KEY → OK[\r]

Ex.3) Press and Hold L/O KEY → KEY,L,L[\r] ← OK[\r]

The status of KEY HOLD does time-out in 10 seconds after having received the command of KEY HOLD when there is not communication.(For example, “KEY,F,H”.)

224

<COMMAND POF> Power OFF

Controller → Radio POF[\r]

Radio → Controller POF,OK[\r]

Turns off the scanner. After this command, the scanner doesn't accept any command.

<COMMAND QSH> Go to quick search hold mode

Controller → Radio QSH,[FRQ],[RSV],[MOD],[ATT],[DLY],[RSV],[CODE_SRCH],[BSC],[REP],[RSV], [AGC_ANALOG],[AGC_DIGITAL],[P25WAITING][\r]

Radio → Controller QSH,OK[\r] or QSH,NG[\r]

[FRQ] : Frequency (The right frequency)

[MOD] : Modulation (AUTO/AM/FM/NFM/WFM/FMB) [ATT] : Attenuation (0:OFF / 1:ON) [DLY] : Delay Time (-10,-5,-2,0,1,2,5,10,30) [CODE_SRCH] : CTCSS/DCS/P25 NAC Search

(0:OFF / 1: CTCSS/DCS / 2: P25 NAC Search)

[BSC] : Broadcast Screen (16digit: ########･･#) (each # is 0 or 1) ||||||||･･+- Band10

0 means OFF |||||||| : 1 means ON |||||||+---- Band 2

||||||+----- Band 1 |||||+------ Reserve ||||+------- NOAA WX |||+-------- VHF TV ||+--------- UHF TV |+---------- FM +----------- Pager

[REP] : Repeater Find (0:OFF / 1:ON)

[AGC_ANALOG] : AGC Setting for Analog Audio (0:OFF / 1:ON)

[AGC_DIGITAL] : AGC Setting for Digital Audio (0:OFF / 1:ON)

[P25WAITING] : P25 Waiting time

(0,100,200,300, .... , 900,1000)

0 : 0ms 100 : 100ms 200 : 200ms 300 : 300ms 400 : 400ms 500 : 500ms 600 : 600ms 700 : 700ms 800 : 800ms 900 : 900ms 1000 : 1000ms

[RSV] : Reserve Parameter * This is always only “,”. This command is invalid when the scanner is in Menu Mode, during Direct Entry operation, during Quick Save operation.

225

FUNCTION UASD specifies arbitrary frequency and changes to Quick Search Hold (VFO) mode. Parameter, such as STP, changes the contents of Srch/CloCall option. Note: Even when only [FRQ] parameter is set, this command will work.

<COMMAND QSC> Set current frequency and get reception status

Controller → Radio QSC,[FRQ],[RSV],[MOD],[ATT],[DLY],[RSV],[CODE_SRCH],[BSC],[REP],[ RSV], [AGC_ANALOG],[AGC_DIGITAL],[P25WAITING] [\r]

Radio → Controller QSC,[RSSI],[FRQ],[SQL][\r] or QSC,NG[\r]

[FRQ] : Frequency (The right frequency)

[MOD] : Modulation (AUTO/AM/FM/NFM/WFM/FMB) [ATT] : Attenuation (0:OFF / 1:ON) [DLY] : Delay Time (-10,-5,-2,0,1,2,5,10,30)

[CODE_SRCH] : CTCSS/DCS Search

(0:OFF / 1: CTCSS/DCS Search / 2: P25 NAC Search)

[BSC] : Broadcast Screen (16digit: ########･･#) (each # is 0 or 1) ||||||||･･+- Band10

0 means OFF |||||||| : 1 means ON |||||||+---- Band 2

||||||+----- Band 1 |||||+------ Reserve ||||+------- NOAA WX |||+-------- VHF TV ||+--------- UHF TV |+---------- FM

+----------- Pager [REP] : Repeater Find (0:OFF / 1:ON) [RSSI] : RSSI A/D Value (0-1023)

[SQL] : Squelch Status (0:CLOSE / 1:OPEN) [AGC_ANALOG] : AGC Setting for Analog Audio(0:OFF / 1:ON) [AGC_DIGITAL] : AGC Setting for Digital Audio (0:OFF / 1:ON)

[P25WAITING] : P25 Waiting time

(0,100,200,300, .... , 900,1000)

0 : 0ms 100 : 100ms 200 : 200ms 300 : 300ms 400 : 400ms 500 : 500ms 600 : 600ms 700 : 700ms 800 : 800ms 900 : 900ms 1000 : 1000ms

[RSV] : Reserve Parameter * This is always only “,”.

226

This command is invalid when the scanner is in Menu Mode, during Direct Entry operation, during Quick Save operation.

FUNCTION UASD specifies arbitrary frequency and changes to Quick Search Hold (VFO) mode. Parameter, such as STP, changes the contents of Srch/CloCall option.

<COMMAND CSC> Go to Custom search and get reception status

Controller → Radio

① CSC,ON[\r] ② CSC,OFF[\r]

Radio → Controller ① CSC,[RSSI],[FRQ],[SQL][\r]

CSC,[RSSI],[FRQ],[SQL][\r] CSC,[RSSI],[FRQ],[SQL][\r]

....

CSC,[RSSI],[FRQ],[SQL][\r]

② CSC,OK[\r] [RSSI] : RSSI A/D Value (0-1023) [FRQ] : Current Frequency

[SQL] : Squelch Status (0:CLOSE / 1:OPEN)

This command outputs custom search status of each frequency sequentially. Use CSC,OFF command to stop the output.

This command is invalid when the scanner is in Menu Mode, during Direct Entry operation, during Quick Save operation.

<COMMAND PWR> *Get RSSI Level

Controller → Radio PWR[\r]

Radio → Controller PWR,[RSSI],[FRQ][\r]

[RSSI] : RSSI A/D Value (0-1023) [FRQ] : Current Frequency

Returns current RSSI level and its frequency. The order of the frequency digits is from 1 GHz digit to 100 Hz digit.

227

<COMMAND STS> Get Current Status

Controller → Radio STS[\r]

Radio → Controller STS,[DSP_FORM],[L1_CHAR],[L1_MODE],[L2_CHAR],[L2_MODE],[L3_CHAR],[L3_MODE],

[L4_CHAR],[L4_MODE],････,[L8_CHAR],[L8_MODE],[SQL],[MUT],[BAT],[WAT],[RSV], [RSV],[SIG_LVL],[BK_COLOR],[BK_DIMMER][\r]

[DSP_FORM] : Display Form (4 - 8dight:########) (each # is 0 or 1) 0 means Small Font / 1 means Large Font.

[L1_CHAR] : Line1 Characters 16char (fixed length)

[L1_MODE] : Line1 Display Mode 16char

[L2_CHAR] : Line2 Characters 16char (fixed length)

[L2_MODE] : Line2 Display Mode 16char

[L3_CHAR] : Line3 Characters 16char (fixed length)

[L3_MODE] : Line3 Display Mode 16char

[L4_CHAR] : Line4 Characters 16char (fixed length)

[L4_MODE] : Line4 Display Mode 16char

:

[L8_CHAR] : Line8 Characters 16char (fixed length)

[L8_MODE] : Line8 Display Mode 16char

[SQL] : Squelch Status (0:CLOSE / 1:OPEN)

[MUT] : Mute Status (0:OFF / 1:ON)

[RSV] : Reserve Parameter * This is always only “0”.

[BAT] : Battery Low Status (0:No Alert / 1:Alert)

[WAT] : Weather Alert Status (0:No Alert / 1: Alert / $$$: Alert

SAME CODE)

[SIG_LVL] : Signal Level ( 0 – 5 )

[BK_COLOR] : Backlight Color

(OFF,BLUE,RED,MAGENTA,GREEN,CYAN,YELLOW,WHITE)

[BK_DIMMER] : Backlight Dimmer (0:OFF / 1:Low / 2:Middle / 3:High )

NOTE : ) Display Mode for Line1 – Line8 (space) : NORMAL CHAR, *: REVERSE CHAR _ (Under bar) : Underline If all 16chars are normal, only "," is sent.

The number of [Lx_CHAR] and [Lx_MODE] depend on Display Form.

Ex.1) ┌---------------┐ │ -- M E N U -- | Squelch Status : OPEN │Program System | Mute Status : OFF │Program Location| Battery Low Status : No Alert │Srch/CloCall Opt| Weather Alert Status : No Alert └---------------┘ → STS[\r] ← 1111,

-- M E N U -- , ← [L1_CHAR] ________________, ← [L1_MODE] Program System , ← [L2_CHAR] ****************, ← [L2_MODE] Program Location, ← [L3_CHAR]

228

, ← [L3_MODE] Srch/CloCall Opt, ← [L4_CHAR] , ← [L4_MODE]

1,0,0,0,,,0,GREEN,,[\r] Returns current scanner status.

Ex.2) ┌----------------┐ ｜ HOLD L/O | │System 1 ｜ Squelch Status : CLOSE │ 851.0125MHz | Mute Status : ON │ P NFM ATT | Battery Low Status : No Alert │S1: 5 | Weather Alert Status : Alert ｜GRP 2 WX | └----------------┘ → STS[\r] ← 011000, HOLD L/O , ← [L1_CHAR] , ← [L1_MODE] SYSTEM 1 , ← [L2_CHAR] , ← [L2_MODE]

851.0125MHz , ← [L3_CHAR] , ← [L3_MODE] P NFM ATT , ← [L4_CHAR] , ← [L4_MODE] S1: 5 , ← [L5_CHAR] , ← [L5_MODE] GRP 2 WX, ← [L6_CHAR] , ← [L6_MODE]

0,1,0,0,,,1,GREEN,,[\r]

Returns current scanner status.

<COMMAND GLG> Get Reception Status

Controller → Radio GLG[\r]

Radio → Controller GLG,[FRQ/TGID],[MOD],[ATT],[CTCSS/DCS],[NAME1],[NAME2],[NAME3],[SQL],[MUT], [SYS_TAG],[CHAN_TAG],[P25NAC][\r] GLG,,,,,,,,,,[\r]

[FRQ/TGID] : Frequency or TGID [MOD] : Modulation (AM/FM/NFM/WFM/FMB) [ATT] : Attenuation (0:OFF / 1:ON) [CTCSS/DCS] : CTCSS/DCS Status (0-231)

*See CTCSS/DCS CODE LIST about the details of this code. [NAME1] : System, Site or Search Name [NAME2] : Group Name [NAME3] : Channel Name [SQL] : Squelch Status (0:CLOSE / 1:OPEN) [MUT] : Mute Status (0:OFF / 1:ON)

229

[SYS_TAG] : Current system number tag (0-999/NONE) [CHAN_TAG] : Current channel number tag (0-999/NONE)

[P25NAC] : P25 NAC Status ( 0-FFF: 0-FFF / NONE: Nac None)

Get reception status. The Scanner returns GLG,,,,,,,,,[\r] until it detects a frequency or a TGID.

<COMMAND JPM> Jump Mode

Controller → Radio JPM,[JUMP_MODE],[INDEX][\r]

Radio → Controller JPM,OK[\r]

[JUMP_MODE] : SCN_MODE Scan mode SVC_MODE Service Search mode CTM_MODE Custom Search mode CC_MODE Close Call Only mode WX_MODE WX SCAN mode FTO_MODE Tone-Out mode [INDEX] : SCN_MODE Channel Index SVC_MODE PublicSafety News HAM Marine Railroad Air CB FRS/GMRS/MURS Racing FM Special Military CTM_MODE RESERVE CC_MODE RESERVE WX_MODE NORMAL A_ONLY SAME_1 SAME_2 SAME_3 SAME_4 SAME_5 ALL_FIPS FTO_MODE RESERVE

Note) Scanner returns NG in the state that the mode switch cannot be done.

230

<COMMAND MNU> Menu Mode

Controller → Radio MNU,[MENU_INDEX][\r]

Radio → Controller MNU,OK[\r]

[MENU_INDEX] : SVC_MENU : Service Search Select Menu WX_MENU : WX Select Menu CCBAND_MENU : Close Call Band Filter Menu SCR_OPT_MENU : Broadcast Screen Band Menu GL_LIST_MENU : Search Global Lockout List Review Menu SETTING_MENU : Setting Menu

Note) Scanner returns NG in the state that the mode switch cannot be done.

<COMMAND JNT> Jump to Number Tag

Controller → Radio JNT,[SYS_TAG],[CHAN_TAG][\r]

Radio → Controller JNT,OK[\r]

[SYS_TAG] : System Number Tag (0-999/NONE) [CHAN_TAG] : Channel Number Tag (0-999/NONE)

When both [SYS_TAG] and [CHAN_TAG] are set as blank, scanner returns error. When [SYS_TAG] is set as blank, [CHAN_TAG] is set with a number tag, scanner jump to the channel number tag in current system. When [SYS_TAG] is set with a number tag, [CHAN_TAG] is set as blank, scanner jump to the first channel of the system number tag.

<COMMAND MDL> Get Model Info

Controller → Radio MDL[\r]

Radio → Controller MDL,BCD396XT[\r]

Returns Model Information.

<COMMAND VER> Get Firmware Version

Controller → Radio VER[\r]

Radio → Controller VER,Version 1.00.00[\r]

Returns Firmware Version.

231

<COMMAND PRG> Enter Program Mode

Controller → Radio PRG[\r]

Radio → Controller PRG,OK[\r] PRG,NG[\r]

This command is invalid when the scanner is in Menu Mode, during Direct Entry operation, during Quick Save operation.

The scanner goes to Program Mode. The scanner displays "Remote Mode" on first line and "Keypad Lock" on second line in Program Mode.

<COMMAND EPG> Exit Program Mode

Controller → Radio EPG[\r]

Radio → Controller EPG,OK[\r]

The scanner exits from Program Mode. Then the scanner goes to Scan Hold Mode.

<COMMAND BLT> Get/Set Backlight

Controller → Radio BLT[\r] BLT, [EVNT], [COLOR], [DIMMER] [\r]

Radio → Controller BLT, [EVNT], [COLOR], [DIMMER] [\r] BLT,OK[\r] [EVENT] IF : INFINITE 10 : 10sec 30 : 30sec KY : KEYPRESS SQ : SQUELCH [COLOR] : (BLUE,RED,MAGENTA,GREEN,CYAN,YELLOW,WHITE) [DIMMER] : Backlight Dimmer (1:Low / 2:Middle / 3:High)

Get/Set Backlight Setting. This command is only acceptable in Programming Mode.

232

<COMMAND BSV > Get/Set Battery Info

Controller → Radio BSV [\r] BSV,[BAT_SAVE],[CHARGE_TIME][\r]

Radio → Controller BSV, [BAT_SAVE],[CHARGE_TIME] [\r] BSV,OK[\r]

[BAT_SAVE] Battery Save (0:OFF / 1:ON) [CHARGE_TIME] Battery Charge Time (1-16)

< COMMAND COM > Get/Set COM port setting

Controller → Radio COM,[/r] COM,[BAUDRATE],[RSV][/r]

Radio → Controller COM,[BAUDRATE],[RSV][/r] COM,OK[/r]

[BAUDRATE] : OFF :OFF 4800 :4800bps 9600 :9600bps 19200 :19200bps 38400 :38400bps 57600 :57600bps 115200:115200b Note: When receive “COM,OK”, next command should not be send in 2 second. Only PC Control (Baud Rate) does not become an initial-setting value. <COMMAND CLR> Clear All Memory

Controller → Radio CLR[\r]

Radio → Controller CLR,OK[\r]

All the memories are set for initial setting. This command is only acceptable in Programming Mode.

Note : It takes dozens of seconds. Only PC Control (Baud Rate) does not become an initial-setting value.

233

<COMMAND KBP> Get/Set Key Beep and setting

Controller → Radio KBP[\r] KBP,[LEVEL],[LOCK],[SAFE][\r]

Radio → Controller KBP,[LEVEL],[LOCK],[SAFE][\r] KBP,OK[\r]

[LEVEL] : Beep Level (0:Auto / 1-15 / 99:OFF) [LOCK] : Key Lock status (0:OFF / 1:ON) [SAFE] : Key Safe status (0:OFF / 1:ON)

Get/Set Key Beep Setting. This command is only acceptable in Programming Mode.

<COMMAND OMS> Get/Set Opening Message

Controller → Radio OMS[\r] OMS,[L1_CHAR],[L2_CHAR],[L3_CHAR],[L4_CHAR][\r]

Radio → Controller OMS,[L1_CHAR],[L2_CHAR],[L3_CHAR],[L4_CHAR][\r] OMS,OK[\r]

[L1_CHAR] : Line1 Characters (max.16char) [L2_CHAR] : Line2 Characters (max.16char) [L3_CHAR] : Line3 Characters (max.16char) [L4_CHAR] : Line4 Characters (max.16char)

If only space code is set in character area, the message returns default message. This command is only acceptable in Programming Mode.

<COMMAND PRI> Get/Set Priority Mode

Controller → Radio PRI[\r] : Get Priority Mode Setting PRI,[PRI_MODE],[MAX_CHAN],[INTERVAL][\r]

Radio → Controller PRI,[PRI_MODE],[MAX_CHAN],[INTERVAL][\r] PRI,OK[\r]

[PRI_MODE] : Priority Setting (0:OFF / 1:ON / 2:PLUS ON) [MAX_CHAN] : Priority Scan max channels at once (1-100) [INTERVAL] : Priority Scan Interval time (1-10)

Get/Set Priority Mode. This command is only acceptable in Programming Mode.

234

<COMMAND AGV> Get/Set Auto Gain Control

Controller → Radio AGV[\r] AGV,[RSV],[RSV],[A_RES],[A_REF],[A_GAIN],[D_RES],[A_GAIN] [\r]

Radio → Controller AGV,[RSV],[RSV],[A_RES],[A_REF],[A_GAIN],[D_RES],[A_GAIN] [\r] AGV,OK[\r]

[A_RES] : Analog Response Time (-4 - +6) [A_REF] : Analog Reference Gain (-5 - +5) [A_GAIN] : Analog Gain Range ( 0 - 15) [D_RES] : Digital Response Time (-8 - +8) [D_GAIN] : Digital Reference Gain(-5 - +5) [RSV] : Reserve Parameter * This is always only “,”.

Get/Set AGC Setting. This command is only acceptable in Programming Mode.

<COMMAND SCT> Get System Count

Controller → Radio SCT[\r]

Radio → Controller SCT,###[\r] : ### (0 - 500)

Returns the number of stored System. This command is only acceptable in Programming Mode.

<COMMAND SIH> Get System Index Head

Controller → Radio SIH[\r]

Radio → Controller SIH,[SYS_INDEX][\r]

Returns the first index of stored system list. This command is only acceptable in Programming Mode.

<COMMAND SIT> Get System Index Tail

Controller → Radio SIT[\r]

Radio → Controller SIT,[SYS_INDEX][\r]

Returns the last index of stored system list. This command is only acceptable in Programming Mode.

235

<COMMAND QSL> Get/Set System/Site Quick Lockout

Controller → Radio QSL[\r] QSL,[PAGE0],[PAGE1],[PAGE2],[PAGE3],[PAGE4],[PAGE5],[PAGE6],[PAGE7],[PAGE8], [PAGE9][\r]

Radio → Controller QSL,[PAGE0],[PAGE1],[PAGE2],[PAGE3],[PAGE4],[PAGE5],[PAGE6],[PAGE7],[PAGE8], [PAGE9][\r] QSL,OK[\r]

[PAGE0] – [PAGE9] : ########## (each # is 0 - 2) 0 : Not assigned (Displayed as “-“ on the scanner.) 1 : On (Displayed as each number on the scanner.) 2 : Off (Displayed as “*” on the scanner.) The Order of Quick Key is as same as LCD Icon.

[PAGE0] : Quick Key 1 - 9, 0 [PAGE1] : Quick Key11 - 19,10 [PAGE2] : Quick Key21 - 29,20 [PAGE3] : Quick Key31 - 39,30 [PAGE4] : Quick Key41 - 49,40 [PAGE5] : Quick Key51 - 59,50 [PAGE6] : Quick Key61 - 69,60 [PAGE7] : Quick Key71 - 79,70 [PAGE8] : Quick Key81 - 89,80 [PAGE9] : Quick Key91 - 99,90

This command is only acceptable in Programming Mode. It cannot turn on/off the Quick Key that has no System / Site.

<COMMAND QGL> Get/Set Group Quick Lockout

Controller → Radio QGL,[SYS_INDEX][\r] QGL,[SYS_INDEX],##########[\r]

Radio → Controller QGL,##########[\r] QGL,OK[\r]

########## (each # is 0 - 2) : Group Quick Key status of [SYS_INDEX]. 0 : Not assigned (Displayed as “-“ on the scanner.) 1 : On (Displayed as each number on the scanner.) 2 : Off (Displayed as “*” on the scanner.)

The Order of Quick Key is as same as LCD Icon (1 – 9, 0). This command is only acceptable in Programming Mode. It cannot turn on/off the Quick Key that has no Group.

236

<COMMAND CSY> Create System

Controller → Radio CSY,[SYS_TYPE],[PROTECT][\r]

Radio → Controller CSY,[SYS_INDEX][\r]

[SYS_TYPE] : System Type

CNV : CONVENTIONAL

MOT : MOTOROLA TYPE

EDC : EDACS Narrow / Wide

EDS : EDACS SCAT

LTR : LTR

P25S : P25 STANDARD

P25F : P25 One Frequency TRUNK

[SYS_INDEX] : The Index of Created System

[PROTECT] : Protect bit Status (0:OFF / 1:ON)

Creates a system and return created system index. The index is a handle to get/set system information. Returns -1 if the scanner failed to create because of no resource. This command is only acceptable in Programming Mode.

<COMMAND DSY> Delete System

Controller → Radio DSY,[SYS_INDEX][\r]

Radio → Controller DSY,OK[\r]

[SYS_INDEX] : System Index

This command deletes a System. This command is only acceptable in Programming Mode.

237

<COMMAND SIN> Get/Set System Info

Controller → Radio SIN,[INDEX][\r] SIN,[INDEX],[NAME],[QUICK_KEY],[HLD],[LOUT],[DLY],[RSV],[RSV],[RSV],[RSV], [RSV],[START_KEY],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[NUMBER_TAG], [AGC_ANALOG],[AGC_DIGITAL],[P25WAITING][\r]

Radio → Controller SIN,[SYS_TYPE],[NAME],[QUICK_KEY],[HLD],[LOUT],[DLY],[RSV],[RSV],[RSV],[RSV], [RSV],[REV_INDEX],[FWD_INDEX],[CHN_GRP_HEAD],[CHN_GRP_TAIL],[SEQ_NO], [START_KEY],[RSV],[RSV],[RSV],[RSV],[RSV], [NUMBER_TAG],[AGC_ANALOG], [AGC_DIGITAL],[P25WAITING],[PROTECT],[RSV][\r] SIN,OK[\r]

[INDEX] : System Index [SYS_TYPE] : System Type

CNV : CONVENTIONAL

MOT : MOTOROLA TYPE

EDC : EDACS Narrow / Wide

EDS : EDACS SCAT

LTR : LTR

P25S : P25 STANDARD

P25F : P25 One Frequency TRUNK [NAME] : Name (max.16char) [QUICK_KEY] : Quick Key (0-99/.(dot) means none) [HLD] : System Hold Time (0-255) [LOUT] : Lockout (0:Unlocked / 1:Lockout) [DLY] : Delay Time (-10,-5,-2,0,1,2,5,10,30)

[REV_INDEX] : Reverse System Index of the Scan Setting [FWD_INDEX] : Forward System Index of the Scan Setting [CHN_GRP_HEAD] : Channel Group Index Head of the conventional system

or Site Index Head of the Trunked System

[CHN_GRP_TAIL] : Channel Group Index Tail of the conventional system

or Site Index Tail of the Trunked System [SEQ_NO] : System Sequence Number (1 - 500) [START_KEY] : Startup Configuration Key (0-9/.(dot) means none) [NUMBER_TAG] : Number tag (0-999 / NONE) [AGC_ANALOG] : AGC Setting for Analog Audio (0:OFF / 1:ON) [AGC_DIGITAL] : AGC Setting for Digital Audio (0:OFF / 1:ON)

[P25WAITING] : P25 Waiting time (0,100,200, .... , 900,1000)

[PROTECT] : Protect bit Status (0:OFF / 1:ON) [RSV] : Reserve Parameter * This is always only “,”.

Get/Set System Information. The scanner returns only "," to punctuate for parameters which are not appropriate the system type. In set command, the scanner neglects the parameters that are not appropriate the system type. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode. When the system protect bit is ON, except [SYS_TYPE], [NAME], [REV_INDEX], [FWD_INDEX], [CHN_GRP_HEAD], [CHN_GRP_TAIL], other parameters will be send as a reserve parameter in the Radio -> Controller command.

238

<COMMAND TRN> Get/Set Trunk Info

Controller → Radio TRN,[INDEX][\r] TRN,[INDEX],[ID_SEARCH],[S_BIT],[END_CODE],[AFS],[RSV],[RSV],[EMG],[EMGL], [FMAP],[CTM_FMAP],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV] , [MOT_ID],[EMG_COLOR],[EMG_PATTERN],[P25NAC],[PRI_ID_SCAN][\r]

Radio → Controller TRN,[ID_SEARCH],[S_BIT],[END_CODE],[AFS],[RSV],[RSV],[EMG],[EMGL],[FMAP], [CTM_FMAP],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV], [TGID_GRP_HEAD],[TGID_GRP_TAIL],[ID_LOUT_GRP_HEAD],[ID_LOUT_GRP_TAIL], [MOT_ID],[EMG_COLOR],[EMG_PATTERN],[P25NAC],[PRI_ID_SCAN][\r] TRN,OK[\r]

[INDEX] : System Index [ID_SEARCH] : ID Search/Scan (0:ID Scan mode / 1: Search Mode) [S_BIT] : Motorola Status Bit (0:Ignore, 1:Yes)

[END_CODE] : Motorola End Code(0:Ignore,1:Analog,2:Analog and Digital)

[AFS] : EDACS ID Format (0:Decimal / 1:AFS) [EMG] : Emergency Alert (0:Ignore / 1-9:Alert) [EMGL] : Emergency Alert Level (0:OFF / 1 - 15)

[FMAP] : Fleet Map (0-16, 0-15:Preset, 16:Custom)

[CTM_FMAP] : Custom Fleet Map Setting (######## : # is 0-E) # means Size Code of each BLOCK (from 0 to 7)

0 : Size Code 0 5 : Size Code 5 A : Size Code 10

1 : Size Code 1 6 : Size Code 6 B : Size Code 11

2 : Size Code 2 7 : Size Code 7 C : Size Code 12

3 : Size Code 3 8 : Size Code 8 D : Size Code 13

4 : Size Code 4 9 : Size Code 9 E : Size Code 14

[TGID_GRP_HEAD] : TGID Index Head of the System [TGID_GRP_TAIL] : TGID Index Tail of the System [ID_LOUT_GRP_HEAD]: L/O TGID Group Index Head of the System [ID_LOUT_GRP_TAIL]: L/O TGID Group Index Tail of the System

[MOT_ID] : Motorola/P25 ID Format (0:Decimal / 1:HEX ) [EMG_COLOR] : Emergency Alert Light color

(OFF,BLUE,RED,MAGENTA,GREEN,CYAN,YELLOW,WHITE) [EMG_PATTERN] : Emergency Alert Light Pattern(0:ON/1:SLow /2:Fast) [P25NAC] : P25 NAC Status (0-FFF:0-FFF/SRCH:Nac Search) [PRI_ID_SCAN] : Priority ID Scan ( 0:OFF / 1: ON) [RSV] : Reserve Parameter * This is always only “,”.

Get/Sets Trunked System Information. The scanner returns only "," to punctuate for parameters which are not appropriate the system type. In set command, the scanner neglects the parameters that are not appropriate the system. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. When the system protect bit is ON, except [TGID_GRP_HEAD], [TGID_GRP_TAIL], [ID_LOUT_GRP_HEAD], [ID_LOUT_GRP_TAIL], other parameters will be send as a reserve parameter in the Radio -> Controller command. This command is only acceptable in Programming Mode.

239

<COMMAND AST> Append Site

Controller → Radio AST,[SYS_INDEX],[RSV][\r]

Radio → Controller AST,[SITE_INDEX][\r]

[SYS_INDEX] : System Index [SITE_INDEX] : Appended Site Index

Append Site to the system. Returns "-1" if the scanner failed to create because of no resource. This command is only acceptable in Programming Mode.

<COMMAND SIF> Get/Set Site Info

Controller → Radio SIF,[INDEX][\r] SIF,[INDEX],[NAME],[QUICK_KEY],[HLD],[LOUT],[MOD],[ATT],[RSV],[RSV],[RSV], [START_KEY],[LATITUDE],[LONGITUDE],[RANGE],[GPS_ENABLE],[RSV],[MOT_TYPE], [EDACS_TYPE],[P25WAITING],[RSV][\r]

Radio → Controller SIF,[RSV],[NAME],[QUICK_KEY],[HLD],[LOUT],[MOD],[ATT],[C-CH],[RSV],[RSV], [REV_INDEX],[FWD_INDEX],[SYS_INDEX],[CHN_HEAD],[CHN_TAIL],[SEQ_NO], [START_KEY],[LATITUDE],[LONGITUDE],[RANGE],[GPS_ENABLE],[RSV],[MOT_TYPE], [EDACS_TYPE],[P25WAITING],[RSV][\r] SIF,OK[\r]

[INDEX] : Site Index [NAME] : Name (max.16char) [QUICK_KEY] : Quick Key (0-99/.(dot) means none) [HLD] : Site Hold Time (0-255) [LOUT] : Lockout (0:Unlocked / 1:Lockout) [MOD] : Modulation (AUTO/FM/NFM) [ATT] : Attenuation (0:OFF/1:ON) [C-CH] : This parameter is always “1” [REV_INDEX] : Reverse Site Index of the Scan Setting [FWD_INDEX] : Forward Site Index of the Scan Setting [SYS_INDEX] : System Index [CHN_HEAD] : Channel Index Head of the Group List [CHN_TAIL] : Channel Index Tail of the Group List [SEQ_NO] : Site Sequence Number (1-256)

[START_KEY] : Startup Configuration (0-9/.(dot) means none) [LATITUDE] : North or South Latitude [LONGITUDE] : West or East Longitude [RANGE] : Range (1-250 : 1= 0.5 mile or km) [GPS_ENABLE] : GPS Location detection (0:OFF/1:ON) [MOT_TYPE] : Band type for MOT/EDACS(STD/ SPL/CUSTOM) [EDACS_TYPE] : EDACS (WIDE/NARROW)

[P25WAITING] : P25 Waiting time(0,100,200,300, .... , 900,1000)

[RSV] : Reserve Parameter * This is always only “,”.

Get/Set Site Information.

240

The scanner returns only "," to punctuate for parameters which are not appropriate the site type. In set command, the scanner neglects the parameters that are not appropriate the system type. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. When the system protect bit is ON, except [REV_INDEX], [FWD_INDEX], [SYS_INDEX], [CHN_HEAD], [CHN_TAIL], other parameters will be send as a reserve parameter in the Radio -> Controller command. This command is only acceptable in Programming Mode.

<COMMAND MCP> Get/Set Motorola Custom Band Plan

Controller → Radio MCP,[INDEX][\r] MCP,[INDEX],[LOWER1],[UPPER1],[STEP1],[OFFSET1],[LOWER2],[UPPER2],[STEP2], [OFFSET2],[LOWER3],[UPPER3],[STEP3],[OFFSET3],[LOWER4],[UPPER4],[STEP4], [OFFSET4],[LOWER5],[UPPER5],[STEP5],[OFFSET5],[LOWER6],[UPPER6],[STEP6], [OFFSET6][\r],

Radio → Controller MCP,[LOWER1],[UPPER1],[STEP1],[OFFSET1],[LOWER2],[UPPER2],[STEP2], [OFFSET2],[LOWER3],[UPPER3],[STEP3],[OFFSET3],[LOWER4],[UPPER4],[STEP4], [OFFSET4],[LOWER5],[UPPER5],[STEP5],[OFFSET5],[LOWER6],[UPPER6],[STEP6], [OFFSET6][\r], MCP, OK[\r]

[INDEX] : Site Index [LOWER n] : Lower Frequency n

[UPPER n] : Upper Frequency n

[STEP n] : Step n "500": 5.0k “625": 6.25k "1000": 10.0k

"1250": 12.5k "1500": 15.0k "1875": 18.75k

"2000": 20.0k “2500": 25.0k "3000": 30.0k

"3125": 31.25k "3500": 35.0k "3750": 37.5k

"4000": 40.0k "4375": 43.75k "4500": 45.0k

"5000": 50.0k "5500": 55.0k “5625": 56.25k

"6000": 60.0k "6250": 62.5k "6500": 65.0k

"6875": 68.75k "7000": 70.0k "7500": 75.0k

"8000": 80.0k “8125": 81.25k "8500": 85.0k

“8750": 87.5k "9000": 90.0k “9375": 93.75k

"9500": 95.0k "10000": 100.0k

[OFFSETn] : Offset n (-1023 to 1023)

Get/Sets Band Plan Setting for MOT 800 custom/VHF/UHF site.

In set command, if only "," parameters are send the Band Plan setting of the site will not changed. The set command is aborted if any format error is detected. When the system protect bit is ON, all the parameters will be send as a reserve parameter in the Radio -> Controller command. Before using this command, user should set Band Plan type as “Custom” first by using SIF command. This command is only acceptable in Programming Mode.

241

<COMMAND ABP> Get/Set APCO-P25 Band Plan

Controller → Radio ① ABP,[INDEX][\r] ②

ABP,[INDEX],[BASE_FREQ_0],[SPACING_FREQ_0],[BASE_FREQ_1],[SPACING_FREQ_1], . . . [BASE_FREQ_E],[SPACING_FREQ_E],[BASE_FREQ_F],[SPACING_FREQ_F][\r]

Radio → Controller ① ABP,[BASE_FREQ_0],[SPACING_FREQ_0],[BASE_FREQ_1],[SPACING_FREQ_1], . .

. [BASE_FREQ_E],[SPACING_FREQ_E],[BASE_FREQ_F],[SPACING_FREQ_F][\r]

② ABP,OK[\r]

[INDEX] : Site Index

[BASE_FREQ_n] : Base frequency (MHz)(25.0000MHz to 1300.0000MHz,

5.0Hz step)

Base_FREQ_n = (base frequency * 10^6) / 5

(Hexadecimal number) [SPACING_FREQ_n] : Spacing frequency(kHz)(0.125kHz to 128.0kHz,

0.125kHz step)

SPACING_FREQ_n = (spacing frequency *10^3)/125

(Hexadecimal number)

*n : Base Plan number

EX.) Base frequency = 851.00625MHz, Spacing frequency = 6.25kHz [BASE_FREQ_n] = (851.00625*10^6)/5 = A2510A2(H) [SPACING_FREQ_n] = (6.25*10^3)/125= 32 (H)

Band Plan that has no data returns “0”. When the system protect bit is ON, all the parameters will be send as a reserve parameter in the Radio -> Controller command. This command is only acceptable in Programming Mode.

242

<COMMAND TFQ> Get/Set Trunk Frequency Info

Controller → Radio TFQ,[CHN_INDEX][\r] TFQ,[CHN_INDEX],[FRQ],[LCN],[LOUT],[RSV],[NUMBER_TAG],[VOL_OFFSET], [RSV] [\r]

Radio → Controller TFQ,[FRQ],[LCN],[LOUT],[REV_INDEX],[FWD_INDEX],[SYS_INDEX],[GRP_INDEX],[RSV], [NUMBER_TAG],[VOL_OFFSET],[RSV][\r] TFQ,OK[\r]

[CHN_INDEX] : Trunk Frequency Index [FRQ] : Trunk Frequency [LCN] : LCN (EDACS WIDE/NARROW system: 0 to 20 LTR system: 0 to 30)

[LOUT] : Lockout (0:Unlocked / 1:Lockout)

[REV_INDEX] : Reverse Frequency Index of the Site [FWD_INDEX] : Forward Frequency Index of the Site [SYS_INDEX] : System Index of the Frequency [GRP_INDEX] : Index of the Site

[NUMBER_TAG] : Number tag (0-999 / NONE) [VOL_OFFSET] : Volume Offset (-3 - +3)

In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode. For Motorola or EDACS SCAT System, [LCN] is ignored. When the system protect bit is ON, except [REV_INDEX], [FWD_INDEX], [SYS_INDEX], [GRP_INDEX], other parameters will be send as a reserve parameter in the Radio -> Controller command. [NUMBER_TAG] and [VOL_OFFSET] are just used for SCAT system.

<COMMAND AGC> Append Channel Group

Controller → Radio AGC,[SYS_INDEX][\r]

Radio → Controller AGC,[GRP_INDEX][\r]

[SYS_INDEX] : System Index [GRP_INDEX] : appended Channel Group Index

Append Channel Group to the system. Returns "-1" if the scanner failed to create because of no resource. This command is only acceptable in Programming Mode.

243

<COMMAND AGT> Append TGID Group

Controller → Radio AGT,[SYS_INDEX][\r]

Radio → Controller AGT,[GRP_INDEX][\r]

[SYS_INDEX] : System Index [GRP_INDEX] : appended TGID Group Index

Append TGID Group to the system. Returns "-1" if the scanner failed to create because of no resource. This command is only acceptable in Programming Mode.

<COMMAND DGR> Delete Group / Site

Controller → Radio DGR,[INDEX][\r]

Radio → Controller DGR,OK[\r]

[INDEX] : Group / Site Index

This command deletes a Channel Group, TGID Group or Site. This command is only acceptable in Programming Mode.

<COMMAND GIN> Get/Set Group Info

Controller → Radio GIN,[GRP_INDEX][\r] GIN,[GRP_INDEX],[NAME],[QUICK_KEY],[LOUT],[LATITUDE],[LONGITUDE],[RANGE], [GPS ENABLE][\r]

Radio → Controller GIN,[GRP_TYPE],[NAME],[QUICK_KEY],[LOUT],[REV_INDEX],[FWD_INDEX],[SYS_INDEX], [CHN_HEAD],[CHN_TAIL],[SEQ_NO] ,[LATITUDE],[LONGITUDE],[RANGE],[GPS ENABLE] [\r] GIN,OK[\r]

For Group Information [GRP_INDEX] : Group Index [GRP_TYPE] : Group Type (C: Channel Group / T: TGID Group) [NAME] : Name (max.16char) [QUICK_KEY] : Quick Key (1-9,0: means 10, .(dot): means none) [LOUT] : Lockout (0:Unlocked / 1:Lockout) [REV_INDEX] : Reverse Group Index of the System [FWD_INDEX] : Forward Group Index of the System [SYS_INDEX] : System Index [CHN_HEAD] : Channel Index Head of the Group List [CHN_TAIL] : Channel Index Tail of the Group List [SEQ_NO] : Group Sequence Number of the System

[LATITUDE] : North or South Latitude [LONGITUDE] : West or East Longitude [RANGE] : Range (1-250 : 1= 0.5 mile or km) [GPS ENABLE] : GPS Location detection (0:OFF/1:ON)

244

Get/Set Group Information. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. When the system protect bit is ON, except [NAME], [REV_INDEX], [FWD_INDEX], [SYS_INDEX], [CHN_HEAD], [CHN_TAIL], other parameters will be send as a reserve parameter in the Radio -> Controller command. This command is only acceptable in Programming Mode.

<COMMAND ACC> Append Channel / Trunk Frequency

Controller → Radio ACC,[GRP_INDEX][\r]

Radio → Controller ACC,[CHN_INDEX][\r]

[GRP_INDEX] : Channel Group Index [CHN_INDEX] : Appended Channel Index

- or [GRP_INDEX] : Site Index [CHN_INDEX] : Appended Trunk Frequency Index

Append Channel to the group. Or, append Trunk Frequency to the Site. Returns "-1" if the scanner failed to create because of no resource. This command is only acceptable in Programming Mode.

<COMMAND ACT> Append TGID

Controller → Radio ACT,[GRP_INDEX][\r]

Radio → Controller ACT,[INDEX][\r]

[GRP_INDEX] : TGID Group Index [TGID_INDEX] : appended TGID Index

Append TGID to the group. Returns "-1" if the scanner failed to create because of no resource. This command is only acceptable in Programming Mode.

<COMMAND DCH> Delete Channel

Controller → Radio DCH,[INDEX][\r]

Radio → Controller DCH,OK[\r]

[INDEX] : Channel Index, TGID Index or Trunked Frequency Index

This command deletes a Channel and TGID. This command is also valid for deleting a Trunk Frequency. This command is only acceptable in Programming Mode.

245

<COMMAND CIN> Get/Set Channel Info

Controller → Radio CIN,[INDEX][\r] CIN,[INDEX],[NAME],[FRQ],[MOD],[CTCSS/DCS],[TLOCK],[LOUT],[PRI],[ATT],[ALT], [ALTL],[RSV],[AUDIO_TYPE],[P25NAC],[NUMBER_TAG],[ALT_COLOR],[ALT_PATTERN], [VOL_OFFSET] [\r]

Radio → Controller CIN,[NAME],[FRQ],[MOD],[CTCSS/DCS],[TLOCK],[LOUT],[PRI],[ATT],[ALT],[ALTL], [REV_INDEX],[FWD_INDEX],[SYS_INDEX],[GRP_INDEX],[RSV],[AUDIO_TYPE],[P25NAC], [NUMBER_TAG],[ALT_COLOR],[ ALT_PATTERN],[VOL_OFFSET] [\r] CIN,OK[\r]

[INDEX] : Channel Index [NAME] : Name (max.16char) [FRQ] : Channel Frequency [MOD] : Modulation (AUTO/AM/FM/NFM/WFM/FMB) [ATT] : Attenuation (0:OFF / 1:ON)

[CTCSS/DCS] : CTCSS/DCS Status (0-231 )

*See CTCSS/DCS CODE LIST about the details of this code. [TLOCK] : CTCSS/DCS Tone Lockout(0:OFF / 1:ON) [LOUT] : Lockout (0:Unlocked / 1:Lockout) [PRI] : Priority (0:OFF / 1:ON) [ALT] : Alert Tone (0:OFF / 1-9:Tone No) [ALTL] : Alert Tone Level (0:AUTO/ 1-15) [REV_INDEX] : Reverse Channel Index of the Chan0nel Group [FWD_INDEX] : Forward Channel Index of the Channel Group [SYS_INDEX] : System Index of the Channel [GRP_INDEX] : Group Index of the Channel [AUDIO_TYPE] : Audio Type (0:All/1:Analog Only/2:Digital Only) [P25NAC] : P25 NAC Status ( 0-FFF: 0-FFF / SRCH: Nac Search) [NUMBER_TAG] : Number tag (0-999 / NONE) [ALT_COLOR] : Alert Light color

(OFF,BLUE,RED,MAGENTA,GREEN,CYAN,YELLOW,WHITE) [ALT_PATTERN] : Alert Light Pattern(0:ON / 1:SLow / 2:Fast) [VOL_OFFSET] : Volume Offset (-3 - +3)

Get/Set Channel Information. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode. When the system protect bit is ON, except [REV_INDEX], [FWD_INDEX], [SYS_INDEX], [GRP_INDEX], other parameters will be send as a reserve parameter in the Radio -> Controller command.

246

<COMMAND TIN> Get/Set TGID Info

Controller → Radio TIN,[INDEX][\r] TIN,[INDEX],[NAME],[TGID],[LOUT],[PRI],[ALT],[ALTL],[RSV],[AUDIO_TYPE], [NUMBER_TAG],[ ALT_COLOR],[ALT_PATTERN],[VOL_OFFSET][\r]

Radio → Controller TIN,[NAME],[TGID],[LOUT],[PRI],[ALT],[ALTL],[REV_INDEX],[FWD_INDEX], [SYS_INDEX],[GRP_INDEX],[RSV],[AUDIO_TYPE], [NUMBER_TAG],[ ALT_COLOR], [ALT_PATTERN],[VOL_OFFSET] [\r] TIN,OK[\r]

[INDEX] : TGID Index [NAME] : Name (max.16char) [TGID] : TGID [LOUT] : Lockout (0:Unlocked / 1:Lockout)

[PRI] : Priority (0:OFF / 1:ON)

[ALT] : Alert Tone (0:OFF / 1-9:Tone No)

[ALTL] : Alert Tone Level (0:AUTO/ 1-15) [REV_INDEX] : Reverse TGID Index of the Group

[FWD_INDEX] : Forward TGID Index of the Group [SYS_INDEX] : System Index of the TGID [GRP_INDEX] : Group Index of the TGID

[AUDIO_TYPE] : Audio Type (0:All/1:Analog Only/2: Digital Only) [NUMBER_TAG] : Number tag (0-999 / NONE) [ALT_COLOR] : Alert Light color

(OFF,BLUE,RED,MAGENTA,GREEN,CYAN,YELLOW,WHITE) [ALT_PATTERN] : Alert Light Pattern(0:ON / 1:SLow / 2:Fast) [VOL_OFFSET] : Volume Offset (-3 - +3)

Get/Set TGID Information. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode. When the system protect bit is ON, except [REV_INDEX], [FWD_INDEX], [SYS_INDEX], [GRP_INDEX], other parameters will be send as a reserve parameter in the Radio -> Controller command.

<COMMAND GLI> Get Lockout TGID (for Rvw L/O ID)

Controller → Radio GLI,[SYS_INDEX][\r]

Radio → Controller GLI,[TGID][\r] GLI,-1[\r] : No more lockout TGID

This command is used to get L/O TGID list of a system. You should call this command again and again to get all L/O TGID until the

scanner returns “-1”. “-1” means that no more L/O TGID exists.

When the system protect bit is ON, only “-1” will be send in the Radio -> Controller command. This command is only acceptable in Programming Mode.

247

<COMMAND SLI> Get Search L/O TGID

Controller → Radio SLI,[SYS_INDEX][\r]

Radio → Controller SLI,[TGID][\r] SLI,-1[\r] : No more lockout TGID

This command is used to get Search L/O TGID list of the system. Search L/O TGID is the L/O TGID which doesn't belong to any group in the system as a TGID. Compared with GLI command, this command doesn't return any L/O TGID which is belong to one of group in the system. You should call this command again and again to get all L/O TGID until the

scanner returns “-1”. “-1” means that no more L/O TGID exists.

This command is only acceptable in Programming Mode.

<COMMAND ULI> Unlock TGID (for Rvw L/O ID)

Controller → Radio ULI,[SYS_INDEX],[TGID][\r]

Radio → Controller ULI,OK[\r]

This command unlocks a L/O TGID in a system. The TGID is deleted from L/O list. This command is only acceptable in Programming Mode.

<COMMAND LOI> Lockout ID (TGID)

Controller → Radio LOI,[SYS_INDEX],[TGID][\r]

Radio → Controller LOI,OK[\r]

This command locks out a TGID for the system. The TGID is added to L/O list. This command is only acceptable in Programming Mode.

<COMMAND REV> Get Rev Index

Controller → Radio REV,[INDEX][\r]

Radio → Controller REV,[INDEX][\r]

[INDEX] : Index of system, site, group, channel, TGID or Location Alert System.

Returns reverse(backward) index of the index in the memory chain. Returns -1 if no more index exists. This command is only acceptable in Programming Mode.

248

<COMMAND FWD> Get Fwd Index

Controller → Radio FWD,[INDEX][\r]

Radio → Controller FWD,[INDEX][\r]

[INDEX] : Index of system, site, group, channel, TGID or

Location Alert System.

Returns forward index of the index in the memory chain. Returns -1 if no more index exists. This command is only acceptable in Programming Mode.

<COMMAND RMB> Get Remains of Memory Block

Controller → Radio RMB[\r]

Radio → Controller RMB,#####[\r]

Returns the number of idle(free) memory block. : ##### (not zero-padding) This command is only acceptable in Programming Mode.

<COMMAND MEM> Get Memory Used

Controller → Radio MEM[\r]

Radio → Controller MEM,[MEMORY_USED],[SYS],[SITE],[CHN],[LOC][\r]

[MEMORY_USED] : The percent of memory that is used (0 - 100) [SYS] : The number of systems that is created (0 – 500) [SITE] : The number of sites that is created (0 - 1000) [CHN] : The number of channels that is created (0 – 25000) [LOC] : The number of location system that is created (0 – 1000)

This command is only acceptable in Programming Mode.

<COMMAND LIH> Get Location Alert System Index Head

Controller → Radio LIH,[LAS_TYPE][\r]

Radio → Controller LIH,[INDEX][\r]

[LAS_TYPE] : Location Alert Type (POI:POI / DROAD:Dangerous Road / DXING :Dangerous Xing)

Returns the first index of stored location alert system list. This command is only acceptable in Programming Mode.

249

<COMMAND LIT> Get Location Alert System Index Tail

Controller → Radio LIT,[LAS_TYPE][\r]

Radio → Controller LIT,[INDEX][\r]

[LAS_TYPE] : Location Alert Type (POI:POI / DROAD:Dangerous Road / DXING :Dangerous Xing)

Returns the last index of stored location alert system list. This command is only acceptable in Programming Mode.

<COMMAND CLA> Create Location Alert System

Controller → Radio CLA,[LAS_TYPE][\r]

Radio → Controller CLA,[INDEX][\r]

[LAS_TYPE] : Location Alert Type (POI: POI / DROAD: Dangerous Road / DXING: Dangerous Xing) [INDEX] : Location Alert System Index

Creates a system and return created location alert system index. The index is a handle to get/set location alert system information. Returns “-1” if the scanner failed to create because of no resource. This command is only acceptable in Programming Mode.

<COMMAND DLA> Delete Location Alert System

Controller → Radio DLA,[INDEX][\r]

Radio → Controller DLA,OK[\r]

[INDEX] : Location Alert System Index

This command deletes a location alert system. This command is only acceptable in Programming Mode.

250

<COMMAND LIN> Get/Set Location Alert System Info

Controller → Radio LIN,[INDEX][\r] LIN,[INDEX],[LAS_TYPE],[NAME],[LOUT],[ALT],[ALTL],[LATITUDE],[LONGITUDE], [RANGE],[SPEED],[DIR],[ALT_COLOR],[ALT_PATTERN][\r]

Radio → Controller LIN,[LAS_TYPE],[NAME],[LOUT],[ALT],[ALTL],[REV_INDEX],[FWD_INDEX],[SEQ_NO], [LATITUDE],[LONGITUDE],[RANGE],[SPEED],[DIR],[ALT_COLOR],[ALT_PATTERN] [\r] LIN,OK[\r]

[INDEX] : Location Alert System Index [LAS_TYPE] : Location Alert Type

(POI: POI / DROAD: Dangerous Road / DXING: Dangerous Xing) [NAME] : Name (max.16char) [LOUT] : Lockout (0:Unlocked / 1:Lockout) [ALT] : Alert Tone (0:OFF/1 - 4:Tone No.) [ALTL] : Alert Tone Level (0:AUTO/1-15) [REV_INDEX] : Reverse System Index of Location Alert System [FWD_INDEX] : Forward System Index of Location Alert System [SEQ_NO] : Location Alert System Sequence Number [LATITUDE] : North or South Latitude [LONGITUDE] : West or East Longitude [RANGE] : Range (1-80: 1=0.05 mile or km) [SPEED] : Speed Limit (0-200: 1 means 1 mile/hour or km/h) [DIR] : Heading (0-358/360 : 2' step, 360=All range) [ALT_COLOR] : Alert Light color

(OFF,BLUE,RED,MAGENTA,GREEN,CYAN,YELLOW,WHITE)

[ALT_PATTERN] : Alert Light Pattern(0:ON / 1:SLow / 2:Fast)

Get/Set Location Alert System Information. In set command, the scanner neglects the parameters that are not appropriate the system type. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode.

251

<COMMAND SCO> Get/Set Search/Close Call Settings

Controller → Radio SCO[\r] SCO,[RSV],[MOD],[ATT],[DLY],[RSV],[CODE_SRCH],[BSC],[REP],[RSV],[RSV], [MAX_STORE],[RSV],[AGC_ANALOG],[AGC_DIGITAL],[P25WAITING][\r]

Radio → Controller SCO,[RSV],[MOD],[ATT],[DLY],[RSV],[CODE_SRCH],[BSC],[REP],[RSV],[RSV], [MAX_STORE],[RSV],[AGC_ANALOG],[AGC_DIGITAL],[P25WAITING] [\r] SCO,OK[\r]

[MOD] : Modulation (AUTO/AM/FM/NFM/WFM/FMB)

[ATT] : Attenuation (0:OFF / 1:ON) [DLY] : Delay Time (-10,-5,-2,0,1,2,5,10,30) [CODE_SRCH] : CTCSS/DCS Search

(0:OFF / 1: CTCSS/DCS / 2: P25 NAC Search)

[BSC] : Broadcast Screen (16digit: ########･･#) (each # is 0 or 1) ||||||||･･+- Band10

0 means OFF ||||||| : 1 means ON ||||||+---- Band 2

||||||+----- Band 1 |||||+------ Reserve ||||+------- NOAA WX |||+-------- VHF TV ||+--------- UHF TV |+---------- FM +----------- Pager

[REP] : Repeater Find (0:OFF / 1:ON)

[MAX_STORE] : Max Auto Store (1-256) [AGC_ANALOG]: AGC Setting for Analog Audio (0:OFF / 1:ON) [AGC_DIGITAL]: AGC Setting for Digital Audio (0:OFF / 1:ON)

[P25WAITING]: P25 Waiting time (0,100,200,300, .... , 900,1000)

Get/Set Search/Close Call Settings. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode.

<COMMAND BBS> Get/Set Broadcast Screen Band Settings

Controller → Radio BBS,[INDEX][\r] BBS,[INDEX],[LIMIT_L],[LIMIT_H][\r]

Radio → Controller BBS,[LIMIT_L],[LIMIT_H][\r] BBS,OK[\r]

[INDEX] : Index (1-9,0 means 10) [LIMIT_L] : Lower Limit Frequency (00000000 –99999999) [LIMIT_H] : Upper Limit Frequency (00000000 –99999999)

Get/Set Broadcast Screen Band Settings. This command is Only acceptable in Programming Mode.

252

<COMMAND SHK> Get/Set Search Key Settings

Controller → Radio SHK[\r] SHK,[SRCH_KEY_1],[SRCH_KEY_2],[SRCH_KEY_3],[RSV],[RSV],[RSV][\r]

Radio → Controller SHK,[SRCH_KEY_1],[SRCH_KEY_2],[SRCH_KEY_3],[RSV],[RSV],[RSV][\r],SHK,OK[\r]

[SRCH_KEY_1] - [SRCH_KEY_3] : Search Range

.(dot) : Not assign PublicSafety: Public Safety range CUSTOM_1: Custom 1 range News : News range CUSTOM_2: Custom 2 range HAM : HAM Radio range CUSTOM_3: Custom 3 range Marine : Marine range CUSTOM_4: Custom 4 range Railroad : Railroad range CUSTOM_5: Custom 5 range Air : Air range CUSTOM_6: Custom 6 range CB : CB Radio range CUSTOM_7: Custom 7 range FRS/GMRS/MURS: FRS/GMRS/MURS range CUSTOM_8: Custom 8 range Racing : Racing range CUSTOM_9: Custom 9 range FM : FM Broadcast range CUSTOM_10: Custom 10 range Special : Special range TONE_OUT: Tone Out mode Military : Military Air range B_SCOPE: Band Scope

Get/Set Search Key Settings. This command is only acceptable in Programming Mode.

<COMMAND GLF> Get Global Lockout Freq

Controller → Radio GLF[\r]

Radio → Controller GLF,[FRQ][\r] GLF,-1[\r]

[FRQ] : Lockout Frequency (250000-13000000)

This command is used to get Global L/O frequency list. You should call this command again and again to get all-global L/O frequency until the scanner returns "-1". "-1" means that no more L/O frequency exists. This command is only acceptable in Programming Mode.

<COMMAND ULF> Unlock Global L/O

Controller → Radio ULF,[FRQ][\r]

Radio → Controller ULF,OK[\r]

[FRQ] : Lockout Frequency (250000-13000000)

This command unlocks a L/O frequency. The frequency is deleted from L/O list. This command is only acceptable in Programming Mode.

253

<COMMAND LOF > Lock Out Frequency

Controller → Radio LOF,[FRQ][\r]

Radio → Controller LOF,OK[\r]

[FRQ] : Frequency (250000-13000000) This command locks out a frequency. The frequency is added to L/O list. This command is only acceptable in Programming Mode.

<COMMAND CLC> Get/Set Close Call Settings

Controller → Radio CLC[\r] CLC,[CC_MODE],[CC_OVERRIDE],[RSV],[ALTB],[ALTL],[ALTP],[CC_BAND],[LOUT], [HLD],[QUICK_KEY],[NUMBER_TAG],[ ALT_COLOR],[ALT_PATTERN][\r]

Radio → Controller CLC,[CC_MODE],[CC_OVERRIDE],[RSV],[ALTB],[ALTL],[ALTP],[CC_BAND],[LOUT], [HLD],[QUICK_KEY],[NUMBER_TAG],[ ALT_COLOR],[ALT_PATTERN][\r] CLC,OK[\r]

[CC_MODE] : Mode ( 0:OFF / 1:CC PRI / 2:CC DND) [CC_OVERRIDE] : Override (1:ON / 0:OFF) [ALTB] : Alert Beep (0:OFF / 1-9:Tone No) [ALTL] : Alert Tone Level (0:AUTO/ 1-15) [ALTP] : Close Call Pause

3 : 3 sec 5 : 5 sec 10 : 10 sec 15 : 15 sec 30 : 30 sec 45 : 45 sec 60 : 60 sec INF : Infinite

[CC_BAND] : Close Call Band (7digit ####### )

(each # is 0 or 1) ||||||+- 800MHz+ 0 means OFF |||||+-- UHF 1 means ON ||||+--- VHF HIGH2 |||+---- VHF HIGH1 ||+----- AIR BAND |+------ VHF LOW2 +------- VHF LOW1

[LOUT] : Lockout for CC Hits with Scan(0:Unlocked/1:Lockout) [HLD] : System Hold Time for CC Hits with Scan (0-255) [QUICK_KEY] : Quick Key for CC Hits with Scan (0 – 99/.(dot) ) *”.(dot)” means that nothing is assigned. [NUMBER_TAG] : Number tag (0-999 / NONE) [ALT_COLOR] : Alert Light color

(OFF,BLUE,RED,MAGENTA,GREEN,CYAN,YELLOW,WHITE)

[ALT_PATTERN] : Alert Light Pattern(0:ON / 1:SLow / 2:Fast) [RSV] : Reserve Parameter * This is always only “,”.

Get/Set Close Call Settings. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode.

254

<COMMAND SSP> Get/Set Service Search Settings

Controller → Radio SSP,[SRCH_INDEX][\r] SSP,[SRCH_INDEX],[DLY],[ATT],[HLD],[LOUT],[QUICK_KEY],[START_KEY],[RSV], [NUMBER_TAG],[AGC_ANALOG],[AGC_DIGITAL],[P25WAITING] [\r]

Radio → Controller SSP,[SRCH_INDEX],[DLY],[ATT],[HLD],[LOUT],[QUICK_KEY],[START_KEY],[RSV], [NUMBER_TAG],[AGC_ANALOG],[AGC_DIGITAL],[P25WAITING] [\r] SSP,OK[\r]

[SRCH_INDEX] : Service Search Range 1 : Public Safety 6 : Air 12 : Special 2 : News 7 : CB Radio 15 : Military Air 3 : HAM Radio 8 : FRS/GMRS/MURS 4 : Marine 9 : Racing 5 : Railroad 11 : FM Broadcast

[DLY] : Delay Time (-10,-5,-2,0,1,2,5,10,30) [ATT] : Attenuation (0:OFF/1:ON) [HLD] : System Hold Time for Search with Scan(0-255) [LOUT] : Lockout for Search with Scan(0:Unlocked/1:Lockout) [QUICK_KEY] : Quick Key ( 0 – 99 / .(dot) ) [START_KEY] : Startup Configuration Key ( 0 – 9 / .(dot) ) [NUMBER_TAG] : Number tag (0-999 / NONE) [AGC_ANALOG] : AGC Setting for Analog Audio (0:OFF / 1:ON) [AGC_DIGITAL] : AGC Setting for Digital Audio (0:OFF / 1:ON)

[P25WAITING] : P25 Waiting time (0,100,200,300, .... , 900,1000)

The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode.

<COMMAND CSG> Get/Set Custom Search Group

Controller → Radio CSG[\r] CSG,##########[\r] : Status of Each Search Range

Radio → Controller CSG,##########[\r] CSG,OK[\r]

########## (each # is 0 or 1) : 0 : valid / 1 : invalid

The Order of Range is as same as LCD Icon (1 – 10). Get/Set current status of the custom search range. This command is only acceptable in Programming Mode. *It can not set all Custom Search Ranges to "0".

255

<COMMAND CBP> Get/Set C-Ch Only Custom Search MOT Band Plan Settings

Controller → Radio CBP,[SRCH_INDEX][\r] CBP,[SRCH_INDEX],[MOT_TYPE],[LOWER1],[UPPER1],[STEP1],[OFFSET1],[LOWER2], [UPPER2],[STEP2],[OFFSET2],[LOWER3],[UPPER3],[STEP3],[OFFSET3],[LOWER4], [UPPER4],[STEP4],[OFFSET4],[LOWER5],[UPPER5],[STEP5],[OFFSET5],[LOWER6], [UPPER6],[STEP6],[OFFSET6][\r],

Radio → Controller CBP,[MOT_TYPE],[LOWER1],[UPPER1],[STEP1],[OFFSET1],[LOWER2],[UPPER2],[STEP2], [OFFSET2],[LOWER3],[UPPER3],[STEP3],[OFFSET3],[LOWER4],[UPPER4],[STEP4], [OFFSET4],[LOWER5],[UPPER5],[STEP5],[OFFSET5],[LOWER6],[UPPER6],[STEP6], [OFFSET6][\r], CBP, OK[\r]

[SRCH_INDEX : Index (1-9,0 means 10)

[MOT_TYPE] : Band type for MOT(STD/ SPL/CUSTOM)

[LOWER n] : Lower Frequency n

[UPPER n] : Upper Frequency n

[STEP n] : Step n "500": 5.0k “625": 6.25k "1000": 10.0k "1250": 12.5k "1500": 15.0k "1875": 18.75k

"2000": 20.0k “2500": 25.0k "3000": 30.0k "3125": 31.25k "3500": 35.0k "3750": 37.5k "4000": 40.0k "4375": 43.75k "4500": 45.0k "5000": 50.0k "5500": 55.0k “5625": 56.25k "6000": 60.0k "6250": 62.5k "6500": 65.0k "6875": 68.75k "7000": 70.0k "7500": 75.0k "8000": 80.0k “8125": 81.25k "8500": 85.0k “8750": 87.5k "9000": 90.0k “9375": 93.75k "9500": 95.0k "10000": 100.0k

[OFFSETn] : Offset n (-1023 to 1023)

Get/Sets Band Plan Setting for MOT 800custom/VHF/UHFsite when trunking control channel in custom search.

In set command, if only "," parameters are send the Band Plan setting will not changed. The set command is aborted if any format error is detected. If [MOT_TYPE] is not CUSTOM, any other setting will be ignored.

This command is only acceptable in Programming Mode.

256

<COMMAND CSP> Get/Set Custom Search Settings

Controller → Radio CSP,[SRCH_INDEX][\r] CSP,[SRCH_INDEX],[NAME],[LIMIT_L],[LIMIT_H],[STP],[MOD],[ATT],[DLY],[RSV], [HLD],[LOUT],[C-CH],[RSV],[RSV],[QUICK_KEY],[START_KEY],[RSV],[NUMBER_TAG], [AGC_ANALOG],[AGC_DIGITAL],[P25WAITING][\r]

Radio → Controller CSP,[NAME],[LIMIT_L],[LIMIT_H],[STP],[MOD],[ATT],[DLY],[RSV],[HLD],[LOUT], [C-CH],[RSV],[RSV],[QUICK_KEY],[START_KEY],[RSV],[NUMBER_TAG],[AGC_ANALOG], [AGC_DIGITAL],[P25WAITING][\r] CSP,OK[\r]

[SRCH_INDEX] : Index (1-9,0 means 10) [NAME] : Name (max.16char) [LIMIT_L] : Lower Limit Frequency (250000-13000000) [LIMIT_H] : Upper Limit Frequency (250000-13000000) [STP] : Search Step AUTO : AUTO 833 : 8.33k 2000 : 20k 500 : 5k 1000 : 10k 2500 : 25k 625 : 6.25k 1250 : 12.5k 5000 : 50k

750 : 7.5 k 1500 : 15k 10000 : 100k [MOD] : Modulation (AUTO/AM/FM/NFM/WFM/FMB) [ATT] : Attenuation (0:OFF / 1:ON) [DLY] : Delay Time (-10,-5,-2,0,1,2,5,10,30) [HLD] : System Hold Time (0-255)

[LOUT] : Lockout (0:Unlocked / 1:Lockout)

[C-CH] : Control Channel Only (0:OFF / 1:ON) [QUICK_KEY] : Quick Key (0 – 99 / .(dot) )

[START_KEY] : Startup Configuration Key (0 - 9/ .(dot)) [NUMBER_TAG] : Number tag (0-999 / NOE) [AGC_ANALOG] : AGC Setting for Analog Audio (0:OFF / 1:ON) [AGC_DIGITAL] : AGC Setting for Digital Audio (0:OFF / 1:ON)

[P25WAITING] : P25 Waiting time(0,100,200,300, .... , 900,1000)

Get/Set Custom Search Settings. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode.

257

<COMMAND WXS> Get/Set Weather Settings

Controller → Radio WXS[\r] WXS,[DLY],[ATT],[ALT_PRI],[RSV],[AGC_ANALOG],[RSV][\r]

Radio → Controller WXS,[DLY],[ATT],[ALT_PRI],[RSV],[AGC_ANALOG],[RSV] [\r] WXS,OK[\r]

[DLY] : Delay Time (-10,-5,-2,0,1,2,5,10,30) [ATT] : Attenuation (0:OFF / 1:ON) [ALT_PRI] : Weather Alert Priority (0:OFF / 1:ON)

[AGC_ANALOG]: AGC Setting for Analog Audio (0:OFF / 1:ON)

Get/Set Weather Priority Settings. This command is only acceptable in Programming Mode.

<COMMAND SGP> Get/Set SAME Group Settings

Controller → Radio SGP,[SAME_INDEX][\r] SGP,[SAME_INDEX],[NAME],[FIPS1],[FIPS2],[FIPS3],[FIPS4],[FIPS5],[FIPS6], [FIPS7],[FIPS8][\r]

Radio → Controller

SGP,[NAME],[FIPS1],[FIPS2],[FIPS3],[FIPS4],[FIPS5],[FIPS6],[FIPS7],[FIPS8][\r]

SGP,OK[\r]

[SAME_INDEX]: SAME Index (1 – 5 ) [NAME] : SAME Group Name (max.16char) [FIPS1-8] : FIPS Code (6digit:000000-999999, or ------ means none)

Get/Set SAME Group Settings. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected. This command is only acceptable in Programming Mode.

258

<COMMAND TON> Get/Set Tone-Out Settings

Controller → Radio TON,[INDEX][\r] TON,[INDEX],[NAME],[FRQ],[MOD],[ATT],[DLY],[ALT],[ALTL],[TONE_A],[RSV], [TONE_B],[RSV],[RSV],[RSV] ,[ALT_COLOR],[ALT_PATTERN],[AGC_ANALOG],[RSV], [RSV] [\r]

Radio → Controller TON,[INDEX],[NAME],[FRQ],[MOD],[ATT],[DLY],[ALT],[ALTL],[TONE_A],[RSV], [TONE_B],[RSV],[RSV],[RSV] ,[ALT_COLOR],[ALT_PATTERN],[AGC_ANALOG],[RSV], [RSV] [\r] TON,OK[\r]

[INDEX] : Index (1-9,0 means 10) [NAME] : Name (max.16char) [FRQ] : Channel Frequency

[MOD] : Modulation (AUTO / FM / NFM)

[ATT] : Attenuation (0:OFF / 1:ON) [DLY] : Delay Time (0,1,2,5,10,30 / INF : Infinite) [ALT] : Alert Tone (0:OFF/1-9:Tone No.) [ALTL] : Alert Tone Level (0:AUTO/1-15) [TONE_A] : Tone A Frequency ex.) 10000 means 1000.0Hz 00000 means 0.0Hz [RSV] : Reserve Parameter * This is always only “,”. [TONE_B] : Tone B Frequency

[ALT_COLOR] : Alert Light color

(OFF,BLUE,RED,MAGENTA,GREEN,CYAN,YELLOW,WHITE) [ALT_PATTERN]: Alert Light Pattern(0:ON / 1:SLow / 2:Fast) [AGC_ANALOG]: AGC Setting for Analog Audio (0:OFF / 1:ON)

Get/Set Tone-Out Settings. This command is only acceptable in Programming Mode.

<COMMAND CNT> Get/Set LCD Contrast Settings

Controller → Radio CNT[\r] CNT,[CONTRAST][\r]

Radio → Controller CNT,[CONTRAST][\r] CNT,OK[\r]

[CONTRAST] : LCD Contrast (1 - 15)

Get/Set LCD Contrast Settings. This command is only acceptable in Programming Mode.

259

<COMMAND SCN> Get/Set Scanner Option Settings

Controller → Radio SCN[\r] SCN,[DISP_MODE],[RSV],[CH_LOG],[G_ATT],[RSV],[P25_LPF][RSV],[RSV],[RSV], [RSV],[RSV], [RSV],[RSV],[RSV],[RSV],[RSV], [RSV],[RSV],[RSV],[RSV],[RSV][\r]

Radio → Controller SCN,[DISP_MODE],[RSV],[CH_LOG],[G_ATT],[RSV],[P25_LPF],[RSV],[RSV],[RSV], [RSV], [RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV],[RSV][\r] SCN,OK[\r]

[DISP_MODE] : DISPLAY MODE ( 1:MODE1 / 2:MODE2 / 3:MODE3 )

[CH_LOG] : Control Channel Logging ( 0:OFF / 1:ON / 2:Extend ) [G_ATT] : Global attenuator ( 0: OFF / 1: ON ) [P25_LPF] : P25 Low-Pass Filter (0: OFF / 1: ON) [RSV] : Reserve Parameter * This is always only “,”.

Get/Set Scanner Option Settings This command is only acceptable in Programming Mode.

<COMMAND VOL> Get/Set Volume Level Settings

Controller → Radio VOL[\r] VOL,[LEVEL][\r]

Radio → Controller VOL,[LEVEL][\r] VOL,OK[\r]

[LEVEL] : Volume Level ( 0 - 15 )

<COMMAND SQL> Get/Set Squelch Level Settings

Controller → Radio SQL[\r] SQL,[LEVEL][\r]

Radio → Controller SQL,[LEVEL][\r] SQL,OK[\r]

[LEVEL] : Squelch Level (0:OPEN / 1-14 / 15:CLOSE)

<COMMAND P25> Get/Set APCO Data Settings

Controller → Radio P25[\r]

Radio → Controller P25,[RSV],[RSV],[ERR_RATE][\r]

[ERR_RATE] : Error Rate (from 0 to 99)

260

<COMMAND DBC> Get/Set Default Band Coverage Settings

Controller → Radio DBC,[BNAD_NO][\r] DBC,[BNAD_NO],[STEP],[MOD][\r]

Radio → Controller DBC, [STEP],[MOD] [\r] DBC,OK[\r]

[BAND_NO] : Band No (1-31)

Band number of band coverage [STP] : Search Step

500 : 5k 625 : 6.25k 750 : 7.5 k

833 : 8.33k 1000 : 10k 1250 : 12.5k 1500 : 15k 2000 : 20k 2500 : 25k 5000 : 50k 10000 : 100k

[MOD] : Modulation (AM / NFM / FM / WFM / FMB)

This command is only acceptable in Programming Mode.

<COMMAND GDO> Get/Set GPS Disp Option

Controller → Radio GDO[\r] GDO,[DISP_MODE],[UNIT],[TIME_FORMAT],[TIME_ZONE],[POS_FORMAT][\r]

Radio → Controller GDO,[DISP_MODE],[UNIT],[TIME_FORMAT],[TIME_ZONE],[POS_FORMAT][\r] GDO,OK[\r]

[DISP_MODE] : Display GPS Mode

( 0:ETA / 1:Clock / 2:Elevation / 3:Speed / 4:Location )

[UNIT] : Distance Unit ( 0: mile / 1: km ) [TIME_FORMAT]: Time Format ( 0: 12 H / 1: 24H) [TIME_ZONE] : Time Zone (-14.0/-13.5/.../-0.5/0.0/0.5/.../13.5/14.0)

ex) “-14.0” means “- 14.0 H”.

[POS_FORMAT]: Position Format ( DMS / DEG )

This command is only acceptable in Programming Mode.

261

<COMMAND BSP> Get/Set Band Scope System Settings

Controller → Radio BSP[\r] BSP,[FRQ],[STP],[SPN],[MAX_HOLD][\r]

Radio → Controller BSP,[FRQ],[STP],[SPN],[MAX_HOLD][\r] BSP,OK[\r]

[FRQ] : Center Frequency [STP] : Search Step 500 : 5k 625 : 6.25k 750 : 7.5 k

833 : 8.33k 1000 : 10k 1250 : 12.5k 1500 : 15k 2000 : 20k 2500 : 25k 5000 : 50k 10000 : 100k

[SPN] : Sweep Span

0.2M, 0.4M, 0.6M,

0.8M, 1M, 2M, 4M, 6M, 8M, 10M, 20M, 40M, 60M, 80M, 100M, 120M, 140M, 160M, 180M, 200M, 250M, 300M, 350M, 400M, 450M, 500M

[MAX_HOLD] : Max Hold Display (0:OFF / 1:ON)

Get/Set Band Scope System Settings. In set command, only "," parameters are not changed. The set command is aborted if any format error is detected.

This command is only acceptable in Programming Mode.

<COMMAND GIE> Get Global IF exchange Frequency

Controller → Radio GIE [\r]

Radio → Controller GIE,[FRQ][\r] GIE,-1[\r]

[FRQ] : IF Exchange Frequency (250000-13000000)

This command is used to get Global IF exchange frequency list. You should call this command again and again to get all global IF exchange frequencies until the scanner returns "-1". "-1" means that no more IF exchange frequency exists. This command is only acceptable in Programming Mode.

262

<COMMAND CIE> Clear IF exchange Frequency

Controller → Radio CIE,[FRQ][\r]

Radio → Controller CIE,OK[\r]

[FRQ] : IF Exchange Frequency (250000-13000000)

This command clear Frequency from Global IF exchange Frequency list. This command is only acceptable in Programming Mode.

<COMMAND RIE> Register IF exchange Frequency

Controller → Radio RIE,[FRQ][\r]

Radio → Controller RIE,OK[\r]

[FRQ] : IF Exchange Frequency (250000-13000000)

This command register Frequency to Global IF exchange Frequency list. This command is only acceptable in Programming Mode.

<COMMAND BAV> *Get Battery Voltage

Controller → Radio BAV[\r]

Radio → Controller BAV,####[\r] : A/D Value (0-1023)

Battery Level[V] = (3.2[V] * #### * 2 )/1023

Returns current battery voltage. This command is for test mode.

<COMMAND WIN> *Get Window Voltage

Controller → Radio WIN[\r]

Radio → Controller WIN,###,[FRQ][\r] : ### : A/D Value (0-255)

Returns current window voltage and its frequency. The order of the frequency digits is from 1 GHz digit to 100 Hz digit. This command is for test mode.

263

Uniden BCD396XT remote commands

Specifications and Main Features

Frequently Asked Questions

User Manual