Ubiquiti UniFi UVC-Pro Quick Start Manual

1080p Indoor/Outdoor IP
Camera with Infrared and

3xOptical Zoom

Model: UVC-Pro

Introduction

Thank you for purchasing the Ubiquiti Networks™ UniFi® Video
Camera PRO

. This Quick Start Guide is designed to guide you
through the installation of the camera and show you how to
access the Camera Configuration Interface. This Quick Start
Guide also includes the warranty terms.

The UniFi® Video software and User Guide are available for
download at downloads.ubnt.com/unifivideo

Package Contents

Camera PoE Adapter

(48V, 0.5A)

Power Cord Hex

Keys

Metal

Strap

1080p Indoor/Outdoor IP
Camera with Infrared and

3xOptical Zoom

Model: UVC-Pro

Pan Head Screws

(M4x30, Qty. 4)

Screw Anchors

(Qty. 4)

Ethernet

Sleeve

Mounting

Template

Quick Start

Guide

Installation Requirements

Wall-Mounting:

• Drill

• Drill bit, 7 mm

• Hole saw, 45 mm (optional)

• Phillips screwdriver

Pole-Mounting:

• Screwdriver or 7 mm socket driver

TERMS OF USE: Shielded Ethernet cable and earth grounding must be used as conditions of
product warranty. TOUGHCable™ is designed for outdoor installations. It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, and Dynamic Frequency Selection (DFS) requirements.

Optional Accessories

Ubiquiti Networks offers additional accessories that can be
purchased for use with the UniFi Video Camera PRO. For
accessory installation instructions, refer to the Quick Start
Guide that accompanies the product.

Cable Accessory (UVC-Pro-C)

The UniFi Video Camera PRO Cable Accessory provides
additional connectivity options for UniFi Video Camera PRO,
including audio in/out and mFi® mPort options. There is also a
reset button and PoE/Ethernet connector.

Audio In/Out

Reset

mPort

POE/Ethernet

Connects to

UVC-Pro

Large Pole Mount (UVC-Pro-M)

The UniFi Video Camera PRO Large Pole Mount accommodates
larger poles up to 160 mm wide.

Hardware Overview

Camera Adjustment

Adjusts Camera Up or Down

Rotates CameraRotates Base

Waterproof Gland

The UniFi Video Camera PRO has a waterproof gland for
connecting Ethernet. Below are the components that make up
the waterproof gland:

Seal

Housing

Compression Nut

Ethernet Connector

Reset Pins

To reset the UniFi Video Camera PRO to factory default
settings, use the hex keys or an electric conductor to short the
pins. (The two Reset Pins are called out in the diagram above.)

Installation Overview

The installation process differs depending on if you are
mounting the camera on a wall or on a pole. Follow the
instructions for the installation that you are performing.

Wall Mount

1. Remove the adhesive Mounting Template from the backing

and place the label on the wall where you want the camera.

2. Use a 7 mm drill bit to drill the four anchor holes in the wall.

(Optional) If threading the cabling through the wall, drill
the center hole using a 45 mm hole saw.

3. Insert the four Screw Anchors into the wall.

*640-00059-03*

640-00059-03

4. Thread the cabling through the wall or one of the recessed

areas on the Mounting Bracket Base.

Note: There are two recessed areas for an Ethernet

cable on the Mounting Bracket Base. Place the Ethernet
cable in the recessed area closest to your power
source.

5. Use a Phillips screwdriver to secure the camera to the wall

with the four Pan Head Screws.

Proceed to “Connecting Power and Ethernet”.

Pole Mount

To mount the camera on a pole, use the included Metal Strap:

1. Open the Metal Strap by turning the locking screw

counter-clockwise.

2. Slide the Metal Strap through the back of the camera.

3. Wrap the Metal Strap around the pole. Use a screwdriver or

7 mm socket drive to turn the locking screw clockwise and
securely fasten the strap to the pole.

Connecting Power and Ethernet

1. Disassemble the waterproof gland by turning the

Compression Nut counter-clockwise.

2. Seperate the Seal from the Housing.

3. Insert the Ethernet cable through the Compression Nut and

the Housing. Ensure the threads of the Compression Nut
face the notches on the Housing.

4. Wrap the Seal around the Ethernet cable.