UBIQUITI UBI UVC-G3 Instructions
1080p Indoor/Outdoor
IP Camera with Infrared
Model: UVC-G3
Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi® Video
Camera G3. This Quick Start Guide is designed to guide you
through installation and also includes warranty terms.
Package Contents
UVC-G3
Cable Gland
Pole Mount
* Only the single-pack of the UVC-G3 includes a PoE adapter and a
power cord.
Bracket
PoE Adapter (24V, 0.5A)
with Mounting Bracket*
Screw Anchors
(Qty. 2)
Machine Screws
(Qty. 2)
Power Cord*
Self-Tapping Screws
(Qty. 2)
1080p Indoor/Outdoor
IP Camera with Infrared
Model: UVC-G3
Quick Start
Guide
Installation Requirements
• Shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded
through the AC ground of the PoE.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). Shielded Ethernet
cable and earth grounding must be used for outdoor installations as conditions of product
warranty. TOUGHCable™ is designed for outdoor installations. It is the professional installer’s
responsibility to follow local country regulations.
www.ubnt.com/toughcable
Hardware Overview
IR LED
Camera Lens
Ethernet
Camera Lock
Tilt/Mount Lock
Adjustable Base
Cable Gland
Mounting Base
Cable Slot
Ethernet Connects to the Ubiquiti PoE adapter for 24V
passive PoE power and data.
Reset To reset to factory defaults, press and hold the
Reset button for more than 10 seconds while the camera is
poweredon.
Reset
Hardware Installation
The UniFi Video Camera G3 can be mounted on a wall, ceiling,
or pole. Follow the appropriate steps for your installation:
Wall/Ceiling Mount
1. Remove the Mounting Base from the camera by turning the
Tilt/Mount Lock counterclockwise.
2. Mark the mounting holes on the wall or ceiling.
Note: If you are running the cable along the wall or ceiling,
position the Cable Slot towards the direction you want the
cabling to run. For outdoor installations, position the Cable
Slot downward.
3. Use a 7 mm drill bit to drill the mounting holes in the wall
or ceiling.
Note: If
you are running the Ethernet cable through
the wall, cut a hole centered between the mounting
holes that is large enough to feed the cable through.
4. Insert a Screw Anchor into each mounting hole.
5. If you are feeding the Ethernet cable through the wall or
ceiling, do so now and feed it through the Mounting Base.
If not, feed the Ethernet cable through the Mounting Base
and place the cable in the Cable Slot.
show the Cable Slot positioned downward.
These instructions
IMPORTANT: If you are installing your camera outdoors,
create a drip loop in the cable below the camera to
prevent wateringress.
6. Fasten the Mounting Base to the wall or ceiling using two
Self-Tapping Screws.
7. Remove the camera from the Adjustable Base by turning
the Camera Lock counterclockwise.
8. Feed the Ethernet cable through the Cable Gland and
Adjustable Base.
pressing around its edges.
Ethernet Port on the camera.
IMPORTANT: For proper weather sealing, the Cable
Gland must fit securely within the Adjustable Base when
the camera is mounted. Ensure that the Cable Gland is
securely seated during installation and cable routing.
9. Connect the camera back to the Adjustable Base by turning
the Camera Lock clockwise.
Seal the Cable Gland in place by firmly
Then connect the cable to the
Cable Gland
10. Set the pan angle of the Adjustable Base while connecting
it to the Mounting Base. Then lock the camera to the
Mounting Base by turning the Tilt/Mount Lock clockwise.
Pole Mount
To mount the UVC-G3 on a pole, a metal strap or hose clamp is
required (not included).
1. Feed the metal strap through the slots on the Pole Mount
Bracket.
Loading...