Transition Networks SSDTF1014-100, SSDTF1015-100, SSDTF1011-100, SSDTF1013-100, SSDTF1012-100 User Manual

...

COMPLIANCE INFORMATION

UL Listed C-UL Listed (Canada) CISPR22/EN55022 Class A + EN55024 CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques appropriées

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

© 2001, 2002 TRANSITION Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A. 33202.C

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten

verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur

Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

TRANSITION Networks SSDTF10xx-100 series media converters encode and decode T1 or E1 twisted-pair copper signals over duplex fiber-optic cable to extend the distance and transmission reliability of high speed T1 or E1 data traffic.

*In SSDTF10xx model designation, 10 represents the T1 or E1 RJ-45 connector; xx represents the selectable fiber connector installed on the media converter.

T1/E1 Twisted-Pair Copper

to Fiber

Media Converters

SSDTF10xx*-100

USER’S GUIDE

SSDTF1011-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and a set of RX/TX ST connectors to 850 nm multimode duplex fiber-optic cable.

SSDTF1012-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX ST connector to 1300 nm singlemode duplex fiber-optic cable.

SSDTF1013-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC connector to 850 nm multimode duplex fiber-optic cable.

SSDTF1014-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC-SM connector to 1300 nm singlemode duplex fiber-optic cable.

SSDTF1015-100 (long haul)

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC-LH connector to 1300 nm singlemode duplex fiber-optic cable.

SSDTF1022-100 (long haul)

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX ST connector to 1300 nm singlemode duplex fiber-optic cable.

SSDTF10xx in the Network . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . .7

Fault Isolation and Correction . . . . .8

Cable Specifications . . . . . . . . . . . . .9

Technical Specifications . . . . . . . . .11

Compliance Information . . . . . . . . .12

9-12 VDC INPUT

T!/E1 TP to Fiber

Media Converter

SSDTF10xx IN THE NETWORK

NOTE: THE SSDTF10xx REQUIRES A CSU BETWEEN THE MEDIA CONVERTER AND THE PUBLIC TELEPHONE NETWORK.

NOTE: T1/E1 MEDIA CONVERTERS MUST BE USED IN PAIRS. A TRANSITION Networks SSDTF10xx stand-alone media converter can be used with another SSDTF10xx stand-alone media converter, with a CSDTF10xx chassis media converter, or with a previous model TRANSITION Networks T1/E1 media converter, such as a C/T1E1-CF-01 or a T1E1-CF-01.

Features

• Media converter is framing independent (as ESF vs D4) and supports all common line codes, (AMI, B8ZS, HDB3).

• Dry relay contacts allow media converter to be tied into separate alarm circuit

• All Ones Insertion (AIS) on loss of signal at copper and/or fiber interface.

TECHNICAL SPECIFICATIONS

Standards Emissions: CISPR A

T1/E1 Physical Layer: ITU-T, ANSI, AT&T, ETSI

Dimensions 2.9" x 4.8" x 1.4" Weight 8 oz (approximate) Power Source 7.5-15.9 VDC AC Adapter

Power Consumption 5 watts Power Supply Requirements Replace power supply with only the equivalent

input rating (see below) and output rating (regulated 9VDC at 550 mA).

TN PN Requirement Location

25034 or 3525 240 volts, 50 hertz United Kingdom 25034 or 3525 230 volts, 50 hertz Europe 3518 120 volts, 60 hertz USA/Canada/Mexico 3514 100 volts, 50-60 hertz Japan 25034 or 3525 240 volts, 50 hertz Australia

Environment Typical Operating Temperature*: 0°

to 50°C (32° to 122°F )

Storage Temperature: -20°

to 85°C (-4° to 185°F)

Humidity 10-90%, non condensing Altitude 0-10,000 feet

Warranty Lifetime

DECLARATION OF CONFORMITY

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA Model: SSDTF10xx Series Copper-to-Fiber Media Converter Part Number: SSDTF1011-100, SSDTF1012-100, SSDTF1013-100,

SSDTF1022-100

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the SSDTF10xx to which this declaration refers is in

conformity with the following standards. EN 55022:1994; EN 55024:1998; FCC Part 15 Class A; EN 60950 A4:1997; UL 1950

I, the undersigned, hereby declare that the equipment specified above conforms to the

above Directive(s) and Standard(s).

_January 8, 2001_____

Stephen Anderson, Vice-President of Engineering Date

T1 Network Extension

PWR

SPD

PWR

LKF

DB-9

FLNK

FRX

RXF

CLNK

CRX

LKC

RXC

100BASE-FX

10BASE-FL

RESET

INIT

12C

PWR

10BASE-T

12C-1TERM

LNK

CFETF100

ASTER

CETTF100

PWR

SPD

PWR

SPD

FLNK

FRX

FLNK

FRX

CRX

CLNK

CRX

CLNK

TX 100BASE-FX

10/100SX

10/100TX

CFETF110

CSU

+ 4 hidden pages