TP-Link TL-WPA8631P Quick guide
Quick Installation Guide
Powerline
TL-WPA8631P
* TL-WPA8631P (European version) is used for demonstration in this guide.
* Images may dier from actual products.
Existing Powerline Device
(for demonstration only)
3
Pair the powerline devices.
A
Press the Pair button on the existing powerline
device for 1 second. The Power LED starts blinking.
Note: If the Power LED does not blink, press the Pair
button again.
Blinking
Within 2 minutes
4
Relocate the extender to the Wi-Fi “dead” zone.
Connect your devices to the internet using the
default SSIDs (network name) and password
the label at the side of the extender
B
Within 2 minutes, press the Pair button on the new
extender for 1 second. The Power LED starts blinking.
When the Powerline LED on the new extender turns
on, the pairing process is complete.
If the powerline LED is o, try another wall socket
Note:
or pair again.
Blinking
On
New Extender TL-WPA8631PExisting Powerline Device
on
.
SSID:TP-Link_XXXX
SSID:TP-Link_XXXX_5G
Wireless Password:XXXXXXXX
New Extender
TL-WPA8631P
1
Plug in the new extender near one of your existing powerline devices.
2
Check the new extender’s Powerline LED . Is it on?
Step 4>
Step 3>
If you cannot nd the SSIDs in your Wi-Fi network list, your new extender has automatically
copied over the existing wireless settings. In this case, use the SSID and password of your
existing powerline network to connect.
If you want to unify your Wi-Fi networks, refer to the back page for instructions.
Attention
1. Use the product only in the upright direction.
2. Plug powerline devices into wall outlets instead of power strips.
Using a power strip will aect network performance and may even cause dropped connections.
Wall Outlet Power Strip
©2020 TP-Link 7106508595 REV3.0.0
Unify Your Wi-Fi Networks
WPS
Personalize Your Networks
Copy SSID and password from your router via any of the methods below to create one unied Wi-Fi network
throughout your home.
Note: If your router doesn’t support the two methods below, refer to Personalize Your Networks section to manually change the extender’s Wi-Fi settings.
Method ONE: Via Wi-Fi button
Note: You can use this method when your router has a WPS button.
1.
Press your router’s WPS button
.
2. (Within 2 minutes) press the extender’s Wi-Fi button for 1 second.
The extender’s 2.4 GHz and 5 GHz Wi-Fi LEDs should start
blinking. When
Note: If Wi-Fi settings are not copied within 2 minutes, manually change the
extender’s Wi-Fi settings.
3. Relocate the extender and enjoy the internet using your router’s
they turn solid on, Wi-Fi settings have been copied
.
Wireless Router
Within 2 minutes
Wi-Fi
Extender
SSID and password.
Method TWO: Via OneMeshTM
Note: You can use this method when your router supports OneMeshTM.
1.
Connect your computer to the extender wirelessly. Then visit
tplinkplc.net
2.
Go to OneMesh and toggle on Join OneMesh. When the
extender’s 2.4 GHz and 5 GHz Wi-Fi LEDs turn solid on, Wi-Fi
settings are copied.
3. Enjoy the internet using your router’s SSID and password.
changes to the Wi-Fi settings of your router will be automatically
copied to the extender.
.
SAME
Any
SSID & Password
Blinking
On
Manage your powerline devices using any of the methods below. You
can change the SSID and password, set Wi-Fi schedules, create a guest
network and more.
tpPLC App
For easy management via your smartphone or
tablet, download the app from Apple App Store or
Google Play, or simply scan the QR code.
Scan to download tpPLC App
tpPLC Utility
For easy management via your computer, download the utility on the
product’s Support page at https://www.tp-link.com.
Note: For detailed instructions, refer to the utility manual on the product’s Support page.
Web Interface
To access all settings, connect to an extender wirelessly and visit
http://tplinkplc.net.
Note: For detailed instructions, refer to the product manual on the product’s Support page.
OneMeshTM with Seamless Roaming
TP-Link OneMeshTM router and extenders work together to form one unied
Wi-Fi network. Walk through your home and stay connected with the fastest
possible speeds thanks to OneMesh’s seamless coverage.
Unied Wi-Fi Network
Router and extenders share the same wireless settings, including network name,
password and more.
Seamless Roaming
Devices automatically switch between your router and extenders as you move
through your home for the fastest possible speeds.
Easy Setup and Management
Easily set up and manage a unied Mesh network.
Physical Appearance
Extender TL-WPA8631P
a
Integrated Electrical Socket
Used as a pass-through AC outlet to power other devices. It also
reduces some electrical noise that may interfere with powerline
performance.
b
LED Button
Press for 1 second to turn all LEDs on or o.
c
Reset Button
Press for at least 5 seconds until all LEDs turn o to reset the
extender to factory default settings.
d
Wi-Fi Button
Press for 1 second to begin or stop copying Wi-Fi settings from
the router.
Press and hold for about 5 seconds to turn Wi-Fi on or o.
e
Pair Button
Press for 1 second on two powerline devices within two minutes
to pair them.
a
b
c
d
e
Frequently Asked Questions
Q1. How do I reset my extender to factory default settings?
A. With the extender plugged into an electrical outlet, press and hold the Reset button until
all LEDs turn o. When the LEDs turn back on, the reset process is complete.
Q2. What should I do if my powerline network has no internet connection?
A1. Make sure all powerline adapters and extenders are on the same electrical circuit.
A2. Make sure each device’s Powerline LED is on. If not, pair all devices again.
A3. Make sure all devices are correctly and securely connected.
A4. Check if you have an internet connection by connecting the computer directly to the
modem or router.
Q3. What should I do if a successfully-paired extender does not
reconnect after it is relocated?
A1. Make sure all powerline adapters and extenders are on the same electrical circuit.
A2. Pair it again with another Powerline device, and make sure the Powerline LED is on
before relocating it.
TM
To check full list of TP-Link OneMesh
devices, scan the QR
code, or visit https://www.tp-link.com/One-Mesh/compatibility.
A3. Check for possible interference due to a washing machine, air conditioner or
other household appliance that may be too close to one of the powerline devices.
Plug the appliance into the integrated electrical socket to remove the electrical
noise if your powerline device has an integrated electrical socket.
To ask questions, find answers, and communicate with TP-Link users or engineers,
please visit https://community.tp-link.com to join TP-Link Community.
If you have any suggestions or needs for our product guides, you are welcome
to email techwriter@tp-link.com.cn.
For technical support, replacement services, user guides, and other information,
please visit https://www.tp-link.com/support, or simply scan the QR code.
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant
provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU
declaration of conformity may be found athttps://www.tp-link.com/en/ce.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use the device where wireless devices are not allowed.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
For passthrough devices, plug the power strips into the integrated electrical sockets of the
devices, but devices of the same or another type not be stacked in normal use.
Plug the powerline devices directly into the wall outlets but not the power strips.
Loading...