TP-Link TL-POE2412G, TL-POE4824G Installation Guide

Installation Guide

Passive PoE Adapter

TL-POE2412G/TL-POE4824G

Package Contents: passive PoE adapter, power cord, wall mount kits

Note: TL-POE2412G is used as an example throughout this guide. Other models may dier in appearance.

Connection

Use the passive PoE adapter to simultaneously supply power and transmit data to a passive PoE device.

For technical support and other information, please visit

https://www.tp-link.com/support, or simply scan the QR code

7106508124 REV1.0.2

AC Power Cord

Passive PoE Devices

IP Camera AP

Note: Before connecting a passive PoE device, please check the required voltage in its product manual.

CPE

Passive PoE Adapter

Installation

Note: To ensure the passive PoE adapter is attached most securely, it is recommended to install the adapter with the Ethernet port facing upward.

1. Drill two holes on the wall and insert the plastic wall anchors into the the holes. Secure the mounting bracket to the wall. Make sure the shoulders at the corners of the mounting bracket are on the outside and pointing upward.

2. Attach the passive PoE adapter to the mounting bracket by sliding the adapter in the direction of the arrows until it locks into place.

Ethernet Device

(switch, router, etc.)

LED & Button

Power

On: Power on

O: Power o

Specications

General Specications

IEEE802.3i, IEEE 802.3u, IEEE 802.3abStandards

Output Power

Cable Type

Ports

Environmental and Physical Specications

Operationg Temperature 0˚C to 40˚C (32˚F to 104˚F)

Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)

Operationg Humidity 10% to 90%RH non-condensing

Storage Humidity 5% to 90%RH non-condensing

TL-POE2412G: 24V/0.5A TL-POE4824G: 48V/0.5A

UTP/STP of Cat. 5e or above (based on the standards that the connected devices comply with)

10/100/1000Mbps Auto-Negotiation RJ45 LAN port 10/100/1000Mbps Auto-Negotiation RJ45 POE port

PWRLED

FAQ

Q1. Can the PoE adapter supply power to a passive PoE device which doesn’t have a gigabit Ethernet port?

A: Yes. Both the LAN and the PoE ports of the PoE adapter

comply with IEEE 802.3i and IEEE 802.3u standards and support 10/100Mbps Auto-Negotiation.

Q2. Can the Passive PoE adapter supply power to all my PoE devices?

A: If your devices support passive PoE and the voltage

standards of the devices match that of the passive PoE adapter, the passive PoE adapter can supply power to them.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce.

SAFETY NOTICES

Cautions

Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

限用物質含有情況標示聲明書

限用物質及其化學符號

產品元件名稱

PCB

外殼

電源線

備考1. "超出0.1 wt %" 及 "超出0.01 wt %" 系指限用物質之百分比含量超出百分比含量基準值。備考2. "○"系指該項限用物質之百分比含量未超出百分比含量基準值。備考3. " - " 系指該項限用物質為排除項目。

鉛

鎘

汞

六價鉻

CrVI

多溴聯苯

PBB

多溴二苯醚

PBDE

Explanation of the symbols on the product label

DC voltage

RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment

Indoor use only

AC voltage

Energy eciency Marking