TP-Link TL-POE160S Installation Guide

Installation Guide

Connection

PoE+ Injector

To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.

If you have any suggestions or needs on the product guides, welcome
to email [e-mail].

© 2020 TP-Link 7106509022 REV1.0.0

Powered Device (PD)

IP Camera AP IP Phone

PWR

PoE+ Injector
TL-POE160S

PWR+DATA OUT DATA I N

Ethernet Device

(switch, router, etc.)

The PoE+ Injector supplies steady power and data connectivity to a powered device such as PoE IP Camera, PoE AP and PoE IP Phone

through an Ethernet cable.

Power LED Explanation

Specications

General Specifications

PWR

PWR+DATA OUT DATA IN

On: Supplying power normally

O: No power supply

FAQ

Q1. Can the PoE injector supply power to a PoE device which
doesn’t have a gigabit PoE port?

A:

Yes. All RJ45 ports of the PoE injector support 10/100/1000 Mbps.

Q2. What can I do if my PoE injector doesn’t supply power to
the powered device or the supplied power is unstable?

Standards

LED

Cable Type

Ports

Dimensions
(L×W×H)

Wall
Mountable

IEEE 802.3i, IEEE802.3u, IEEE 802.3ab, IEEE 802.3af
IEEE 802.3at

PWR

UTP/STP of Cat. 5 or above (based on the standards that the
connected devices comply with)

10/100/1000 Mbps RJ45 DATA IN Port
10/100/1000 Mbps RJ45 PWR+DATA OUT Port
AC 100–240 V 50/60 Hz Power Input Port

4.9×2.3×1.4 in (125×59.4×36.8 mm)

Ye s

Environmental and Physical Specifications

Operating Temperature 0˚C to 40˚C (32˚F to 104˚F)

Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)

Operating Humidity 10% to 90% non-condensing

Storage Humidity 5% to 90% non-condensing

A1: Ensure the PD is PoE-compliant and its connecting port supports the PoE

function.

A2: Ensure the power consumption of the PD doesn’t exceed 30 W, otherwise

the overload protection of the PoE injector will be activated. The quality

and length of the Ethernet cable may inuence the reception of the power

supply.

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use any other chargers than those recommended.
Do not use damaged charger or USB cable to charge the device.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.

Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper
use of the device. Please use this product with care and operate at your own
risk.

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at
https://www.tp-link.com/en/ce.

FCC compliance information statement

Product Name: PoE Injector

Model Number: TL-POE160S

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link Nor th America, Inc.

Address: 145 South State College Blvd. Suite 400, Brea, CA 92821

Website: https://www.tp-link.com/us/

Tel: [phone]

Fax: [phone]

E-mail: [e-mail]

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including inter ference that may cause undesired operation.

Any changes or modications not expressly approved by the part y responsible for compliance could void the user’s

authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the
applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the
equipment is properly maintained and operated.

Issue Date: 2020..9.4

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio inter ference, in which case the user

may be required to take adequate measures.

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。こ
の場合には使用者が適切な対策を講ずるよう要求されることがあります。

VCCI-A

BSMI Notice

安全諮詢及注意事項

請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。

此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的
對策。

限用物質含有情況標示聲明書

限用物質及其化學符號

產品元件名稱

PCB

外殼

電源供應器

備考1： "○"系指該項限用物質之百分比含量未超出百分比含量基準值。
備考2： " - " 系指該項限用物質為排除項目。

鉛
Pb

○

○

-

鎘

Cd

○

○

○ ○ ○ ○ ○

汞
Hg

○

○

Explanation of the symbols on the product label

Indoor use only

AC voltage

RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment

(WEEE). This means that this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer
when he buys a new electrical or electronic equipment.

Energy eciency marking (level VI)

六價鉻

+6

Cr

○

○

多溴聯苯

PBB

○

○

多

溴二苯醚

PBDE

○

○

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including inter ference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.

Polarity of output terminals

Class II equipment

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 7 mm

in length. When the screws are xed on the wall, the distance bet ween the screw head and the wall should be more than

1.5 mm.