TP-LINK TD-W8151N User Guide

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router

Rev: 1.0.0

1910010402

Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2010 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarant ee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National Restrictions

2400.0-2483.5 MHz Country Restriction Reason/remark

Bulgaria

France

Italy

Luxembourg None

Norway Implemented

Russian Federation

Note: Please don’t use the product outdoors in France.

Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz

General authorization required for outdoor use and

public service

Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

If used outside of own premises, general authorization is required

General authorization required for network and service supply(not for spectrum)

This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund

Only for indoor applications

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment: Product Description: 150Mbps Wireless N ADSL2+ Modem Router Model No.: TD-W8151N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical

regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC The above product is in conformity with the following standards or other normative documents

ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.8.1:2008& ETSI EN 301 489-17 V2.1.1:2009 EN60950-1:2006

Recommendation 1999/519/EC

EN62311:2008

Directives 2004/108/EC The above product is in conformity with the following standards or other normative documents

EN 55022:2006 +A1:2007 EN 55024:1998+A1:2001+A2:2003 EN 61000-3-2:2006 EN 61000-3-3:1995+A1:2001+A2:2005

Directives 2006/95/EC The above product is in conformity with the following standards or other normative documents

EN60950-1:2006

Directive（ErP） 2009/125/EC Audio/Video, information and communication technology equipment- Environmentally conscious

design

EN62075:2008

Person is responsible for marking this declaration:

Yang Hongliang

Product Manager of International Business

TP-LINK TECHNOLOGIES CO., LTD.

South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan,

Shenzhen, P. R. China

CONTENTS

Package Contents....................................................................................................1

Chapter 1 Introduction.........................................................................................2

1.1 Product Overview..................................................................................2

1.2 Main Features....................................................................................... 2

1.3 Conventions..........................................................................................3

Chapter 2 Hardware Installation..........................................................................4

2.1 The Front Panel ....................................................................................4

2.2 The Back Panel.....................................................................................5

2.3 Installation Environment........................................................................6

2.4 Connecting the Router..........................................................................6

Chapter 3 Quick Installation Guide..................................................................... 8

3.1 Configure PC.........................................................................................8

3.2 Login...................................................................................................11

Chapter 4 Software Configuration .................................................................... 15

4.1 Status..................................................................................................15

4.2 Quick Start ..........................................................................................16

4.3 Interface Setup....................................................................................16

4.3.1 Internet .................................................................................................... 17

4.3.2 LAN ......................................................................................................... 21

4.3.3 Wireless................................................................................................... 23

4.4 Advanced Setup..................................................................................33

4.4.1 Firewall.................................................................................................... 33

4.4.2 Routing.................................................................................................... 34

4.4.3 NAT......................................................................................................... 35

4.4.4 QoS......................................................................................................... 38

4.4.5 VLAN....................................................................................................... 40

4.4.6 ADSL....................................................................................................... 42

4.5 Access Management........................................................................... 43

4.5.1 ACL ......................................................................................................... 43

4.5.2 Filter ........................................................................................................ 44

4.5.3 SNMP...................................................................................................... 51

4.5.4 UPnP....................................................................................................... 52

4.5.5 DDNS ...................................................................................................... 52

4.5.6 CWMP..................................................................................................... 53

4.6 Maintenance........................................................................................54

4.6.1 Administration.......................................................................................... 54

4.6.2 Time Zone ............................................................................................... 55

4.6.3 Firmware.................................................................................................. 56

4.6.4 SysRestart............................................................................................... 58

4.6.5 Diagnostics.............................................................................................. 59

4.7 Help..................................................................................................... 60

Appendix A: Specification.....................................................................................62

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Package Contents

The following contents should be found in your package:

¾ One TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router ¾ One Power Adapter for TD-W8151N ADSL2+ Router ¾ Quick Installation Guide ¾ One RJ45 cable ¾ Two RJ11 cables ¾ One ADSL splitter ¾ One Resource CD , including:

z This User Guide z Other Helpful Information

Note:

)

Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Chapter 1 Introduction

1.1 Product Overview

Thank you for choosing the TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router. The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network.

The TD-W8151N connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors. Multiple workstations can be networked and connected to the Internet using a single Wide Area Network (WAN) interface and single global IP address. The advanced security enhancements, IP/MAC Filter, Application Filter and URL Filter can help to protect your network from potentially devastating intrusions by malicious agents from the outside of your network.

Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the configuration. Network and Router management is done through the Web-based Utility which can be accessed through local Ethernet using any web browser.

ADSL

The TD-W8151N supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports dual latency ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer.

Wireless

In the most attentive wireless security, the Router provides multiple protection measures. It can be set to turn off the wireless network name (SSID) broadcast so that only stations that have the SSID can be connected. The Router provides wireless LAN 64/128-bit WEP encryption security, WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security.

1.2 Main Features

¾ One 10/100Mbps Auto-Negotiation RJ45 LAN port (Auto MDI/MDIX), one RJ11 port. ¾ Provides external splitter. ¾ Adopts Advanced DMT modulation and demodulation technology. ¾ Supports bridge mode and Router function. ¾ Multi-user sharing a high-speed Internet connection. ¾ Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps（With Annex M

enabled).

¾ Supports long transfers, the max line length can reach to 6.5Km. ¾ Supports remote configuration and management through SNMP ¾ Supports PPPoE, it allows connecting the internet on demand and disconnecting from the

Internet when idle.

¾ Provides reliable ESD and surge-protect function with quick response semi-conductive surge

protection circuit.

¾ High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.

and CWMP.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

¾ Supports All ADSL industrial standards. ¾ Compatible with all mainstream DSLAM (CO). ¾ Provides integrated access of internet and route function which face to SOHO user. ¾ Real-time Configuration and device monitoring. ¾ Supports Multiple PVC (Permanent Virtual Circuit). ¾ Built-in DHCP server. ¾ Built-in firewall, supporting IP/MAC filter, Application filter and URL filter. ¾ Supports Virtual Server, DMZ host and IP Address Mapping. ¾ Supports Dynamic DNS, UPnP and Static Routing. ¾ Supports system log and flow Statistics. ¾ Supports firmware upgrade and Web management. ¾ Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security. ¾ Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List).

1.3 Conventions

The Router or device mentioned in this User guide stands for TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router without any explanations.

Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Chapter 2 Hardware Installation

2.1 The Front Panel

Figure 2-1

The LEDs, locating on the front panel, indicates the device’s working status. For details, please refer to LED Explanation.

LED Explanation:

Name Status Indication

Power

Internet

WLAN

On Power is on. Off Power is off. On The LINE port is linked up.

Flash The ADSL negotiation is in progress. ADSL

Off The LINE port is linked down. On A successful PPP connection has been built.

Flash Data is being transferred over the Internet.

Off

Flash

Off On There is a successful connection on the LAN port but no activity.

There is no successful PPP connection or the Router works on Bridge mode.

The wireless function is enabled but no data is being transmitted.

There is wireless data being transmitted.

The wireless function is disabled.

LAN

QSS

Flash Data is being transferred over the LAN port.

Off

Flash

Off

There is no connection on the LAN port or the connection is abnormal.

A wireless device is connecting to the network by QSS function. This process will last in the first 2 minutes and then turn off.

A wireless device has been successfully added to the network by QSS function. The QSS LED will keep on for about 5 minutes and then turn off.

The QSS function is disabled or a wireless device is failed to add the network.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

2.2 The Back Panel

Figure 2-2

¾ POWER: The Power plug is where you will connect the power adapter. ¾ ON/OFF: The power switch for the Router. ¾ RESET: There are two ways to reset the Router's factory defaults.

Method one: With the Router powered on, use a pin to press and hold the Reset button for at least 5 seconds. And the Router will reboot to its factory default settings.

Method two: Restore the default setting from “Maintenance-SysRestart” of the Router's Web-based Utility.

¾ LAN: Through the port, you can connect the Router to your PC or the other Ethernet network

devices.

¾ LINE: Through the port, you can connect the Router with the telephone. Or you can connect

them by an external separate splitter. For details, please refer to “2.4 Connecting the Router”

¾ Antenna: Used for wireless operation and data transmit.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

2.3 Installation Environment

¾ The Product should not be located where it will be exposed to moisture or excessive heat. ¾ Place the Router in a location where it can be connected to the various devices as well as to a

power source.

¾ Make sure the cables and power cord are placed safely out of the way so they do not create a

tripping hazard.

¾ The Router can be placed on a shelf or desktop. ¾ Keep away from the strong electromagnetic radiation and the device of electromagnetic

sensitive.

2.4 Connecting the Router

Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it.

Step 1: Connect the ADSL Line.

Method one: Plug one end of the twisted-pair ADSL cable into the ADSL LINE port on the rear panel of TD-W8151N, and insert the other end into the wall socket.

Method two：You can use a separate splitter. External splitter can divide the data and

voice, and then you can access the Internet and make calls at the same time. The external splitter has three ports:

• LINE: Connect to the wall jack

• PHONE: Connect to the phone sets

• MODEM: Connect to the ADSL LINE port of TD-W8151N

Plug one end of the twisted-pair ADSL cable into the ADSL LINE port on the rear panel of TD-W8151N. Connect the other end to the MODEM port of the external splitter.

Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s

Ethernet port or a regular hub/switch port, and the other end to the LAN port on the TD-W8151N.

Step 3: Power on the computers and LAN devices. Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear

of the device and plug in the adapter to a wall outlet or power extension, and then power on the device.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Figure 2-3

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Chapter 3 Quick Installation Guide

3.1 Configure PC

After you directly connect your PC to the TD-W8151N or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it.

Step 1: Click the Start menu on your desktop, right click My Network Places, and then select

Properties (shown in Figure 3-1).

Figure 3-1

Step 2: Right click Local Area Connection (LAN), and then select Properties.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Figure 3-2

Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties

button.

Figure 3-3

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK.

Figure 3-4

Note:

)

You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above.

Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd or command in the field and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.

If the result displayed is similar to the screen below, the connection between your PC and the Router has been established.

Figure 3-5

If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Router.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Figure 3-6

You can check it follow the steps below:

1) Is the connection between your PC and the Router correct?

The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit.

2) Is the TCP/IP configuration for your PC correct?

If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of

192.168.1.2 ~ 192.168.1.254.

3.2 Login

Once your host PC is properly configured, please proceed as follows to use the Web-based Utility: Start your web browser and type the private IP address of the Router in the address field: http://192.168.1.1/.

After that, you will see the screen shown below. Enter the default User name admin and the default Password admin, and then click OK to access to the Quick Setup screen. You can follow the steps below to complete the Quick Setup.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Figure 3-7

Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen.

Click the NEXT button.

Figure 3-8

Step 2: Configure the time for the Router, and then click the NEXT button.

Figure 3-9

Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for

example here), and then click the NEXT button.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Figure 3-10

Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI

and Connection Type. Then click Next.

Figure 3-11

Step 5: Configure the rules for the WLAN, and click NEXT.

TD-W8151N 150Mbps Wireless N AD SL2+ Modem Router User Guide

Figure 3-12

Note:

)

If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection measures, please refer to section 4.3.3.

Step 6: Click NEXT to save the current settings.

Figure 3-13

Step 7: Click CLOSE to complete.

Figure 3-14

+ 48 hidden pages