TP-Link TD-VG5612 Telephony Feature Guide

Speed Dial

This feature allows you to create short numbers for your frequently used telephone numbers to make your
dialing more convenient. You just need to press one or two digits and the key # instead of the original
phone number to make a call.

Warm Line

With this feature enabled, a call will be automatically directed to a specified party without taking any
additional action when the phone goes off-hook for a certain time. To use this feature, you need to set
warm line numbers first on the web management page.

DND (Do Not Disturb)

With this feature enabled, all the incoming calls will be blocked and the caller will hear the busy tone.

Three-way Call

This feature allows three people to communicate at the same time.

To set up a three-way call, please follow the steps below:

1. Press the FLASH button to put the rst call on hold.

2. Dial the destination number.

3. Wait for the third party to answer and then press FLASH followed by the number 3. Now the three-way call is
successfully set up.

4. To drop yourself out of the call, simply hang up.

A three-way call can also be set up during a call with Call Waiting enabled. When hearing the call waiting tone during a
call, press FLASH followed by the number 3.

Note: The call will end if the initiator of the three-way call hangs up. However, the call will not end if anyone of the other two
parties hangs up. The left two parties remain connected to each other.

Telephony Feature Guide

TP-LINK TECHNOLOGIES CO., LTD.

E-mail: [e-mail]
Website: www.tp-link.com

Specications are subject to change without notice. TP-LINK is a registered trademark of TP-LINK
TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective
holders. Copyright©2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.

7106505724 REV1.0.0

TD-VG5612

300Mbps Wireless N VoIP VDSL/ADSL Modem Router

www.tp-link.com

Telephone Operation

TD-VG5612 allows you to configure some frequently used call features using keypads on your telephone.
To use this feature, you should first enable Feature Code function on the web management page. For the
features mentioned in this table, please refer to Telephony Features in this guide.

Code Description Usage

*193 Enable Wi-Fi. Pick up the phone and dial this code to enable Wi-Fi.

*093

Disable Wi-Fi.

*133

Enable DND (Do Not Disturb).

*033

Disable DND (Do Not Disturb).

*186

Enable Voice Mail.

*086

Disable Voice Mail.

Listen to voice messages stored in

*20

your USB storage device.

Store voice messages within the

*30

USB Storage device.

*27

Enable Redial on busy.

*54

Most Recent Call Return [Incoming]:

#

Internal Calls

*70

Activate PIN & PUK via FXS.

Pick up the phone and dial this code to disable Wi-Fi.

Pick up the phone and dial this code to enable DND.

Pick up the phone and dial this code to disable DND.

Pick up the phone and dial this code to enable Voice Mail
function.

Pick up the phone and dial this code to disable Voice Mail
function.

Pick up the phone to dial this code and then follow the voice
prompts for the operations below:
Press 1 to listen to the previous message.
Press 2 to listen to the current message again.
Press 3 to delete all messages.

Pick up the phone to dial this code and then follow the voice
prompts to record voice messages within the USB Storage device.

Pick up the phone to dial this code. You will hear the confirmation
tone and then the dial tone which will prompt you to dial the
destination number. If the called party is busy, the number will be
dialed again and again until there is response. To end the dialing,
hang up and then pick up your phone.

Pick up the phone to dial this code. The last incoming number will
be dialed automatically.

Pick up the phone to dial this code, and then dial the Internal
Number to make internal calls.

Pick up the phone and dial this code to activate PIN & PUK via FXS.
This feature is only used when the modem router is operating
under 3G/4G Router Mode.

Telephony Features

This section introduces what the following features are used for. For more detailed information, please
refer to the User Guide on the resource CD.

Call Holding

This feature allows you to put a call on hold, in which case the call is not ended but no verbal communica­tion is available.

To put a call on hold, press the FLASH button. To return to the original call, press the FLASH button again.

Call Transfer

This feature allows you to redirect the current call to another phone by using the FLASH button and dialing
the destination number.

To transfer a call, please follow the steps below:

1. Press FLASH button to put the current call on hold.

2. Dial the destination number.

Note: if you want to quit the transfer, press the FLASH button again to return to the original call before hearing the ringback
tone.

3. Hang up when hearing the ringback tone or wait for the newly called party to answer and then hang up. Now the
call is successfully transferred.

Call Waiting

With this feature enabled, if a calling party places a call to you while you are busy, you are able to suspend
the current call and switch to the new incoming call.

To swith to the new incoming call, press FLASH followed by the number 2. The rst call will be automatically put on
hold. You can switch between the two calls by pressing FLASH followed by the number 2.

USB Voice Mail

With this feature enabled and a USB storage device plugged in, the caller will be prompted to leave a voice
message upon the call or when there is no response for a certain time.

Call Forwarding

This feature allows an incoming call to be redirected to a specified party. There are two call forwarding
features, including Call Forwarding Unconditionally and Call Forwarding on No Answer.

With Call Forwarding Unconditionally enabled, no matter whether the called party is engaged or not, the
incoming call will be redirected to the specified party.
With Call Forwarding on No Answer enabled, the incoming call will be redirected to the specified party
when there is no response for a certain time.

Anonymous Calling

This feature allows you to make a call without your phone number or ID being displayed on the called
party's phone.

Anonymous Call Blocking

With this feature enabled, all anonymous calls will be blocked.