Page 1
Quick Start Guide
Smart Temperature and
Humidity Monitor
*Images may dier from actual products.
7106509797 REV1.0.0
Appearance
1
Vent Hole
2
Indicator Icons
3
Temperature*
4
Display/Reset
Button
5
Humidity*
*You can press the button to
switch display position.
Indicator Icons
Connection
• Blinking: Connecting to hub
• Solid On: Connected to hub
• O: No connection
Battery Level
Battery level < 20%
Battery level < 5%
Inside Comfort Level
Outside Comfort Level
The default comfort level is temperatures between 20℃ (68℉)
- 26℃ (78.8℉) while humidity is between 30% - 60%.
You can customize the comfort level on the Tapo app.
Display/Reset Button
• Single Press
Switch the temperature unit ℃/℉.
• Double Press
Switch the display position of temperature and
humidity.
• Press and hold for 5s
Reset your monitor to enter pairing mode.
Before You Start
A Tapo Hub is required. Make sure
your Tapo Hub is successfully added
via the Tapo app.
OR
1. Power Up Your Monitor1
Remove the back panel and insert the
batteries. The screen will light up.
Page 2
2. Set Up Your Monitor2
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete
setup.
3. Test Your Monitor3
Take the monitor to your preferred location.
Make sure the Connection icon on the
screen is solid on. If there is no connection
icon, move it closer to your hub.
4. Place Your Monitor4
Place it on a
table or a shelf
Option 1:
(The installation height should not be higher than 2 meters.)
Option 2:
Magnetically attach to
metallic surfaces
OR
OR
Option 3:
Stick to a clean wall with
the included adhesive
3M
For technical support, the user guide
and more information, please visit
https://www.tapo.com/support/
Risk of explosion if the battery is replaced by an incorrect type.
Avoid replacement of a battery with an incorrect type that can defeat
a safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically
crushing or cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of
ammable liquid or gas; Do not leave a battery subjected to
extremely low air pressure that may result in an explosion or the
leakage of ammable liquid or gas.
Operating Temperature: 0℃ (32℉) - 50℃ (122℉)
Please keep it away from harsh environments with high temperatures or high
humidity.
Do not immerse the vent hole into any liquid.
This monitor is designed to facilitate a healthy lifestyle, but should not be
used as a measuring tool.
Warning
Warning
Do not ingest battery, Chemical Burn Hazard
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper
use of the device. Please use this product with care and operate at your own risk.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be found at
https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment Regulations
2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)
©2022 TP-Link
Loading...