Page 1
Meet Your Temperature and Humidity Sensor
Before You Start
1. Power Up Your Sensor1
2. Set Up Your Sensor
2
3. Test Your Sensor
3
Quick Start Guide
Smart Temperature and
Humidity Sensor
*Images may dier from actual products.
7106509722 REV1.0.0
Measure the temperature and humidity of the environment and send you instant
notications when the environment changes. It is suitable for green houses, bedrooms,
nursery, incubators, and wine cellars.
Sensor
Detector
+
CR2450
LED
Battery Pinhole
Use a pin to press and
remove the cover
Reset Button
Single press: Eective range test
Press for 5s: Reset and enter
pairing mode
A Tapo Hub is required. Make sure your
Tapo Hub is successfully added via the
Tapo app.
OR
Remove the battery insulation tab to power
up your sensor. The LED should blink.
Note: If the LED is not blinking, use a pin to press the Reset
button for 5 seconds to reset your sensor and enter pairing
mode.
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete
setup.
Take your sensor to the preferred location.
Option 1
Single press the Reset button. Your hub
should make a voice prompt.
Reset
Option 2
Blow on the sensor detector. The
temperature and humidity displayed on
the Tapo app should change.
Page 2
4. Place Your Sensor4
Option 1: Hang with the Lanyard
(The installation height should not be higher than 2 meters.)
Option 2: Use Adhesive Magnets
a. Stick the included adhesive magnets to
the back panel.
x2
b. Magnetically attach the sensor to metallic
surfaces.
Metallic Surface
Option 3: Use 3M Adhesives
a. Stick the included 3M adhesives to the
back panel.
3M
3M
3M
3M
3M
3M
x2
b. Stick the sensor to your preferred location.
4. How to replace the battery?
1. Use a pin to press and remove the cover.
2. Replace the battery with a fresh cell.
3. Put the cover back.
+
CR2450
?
Need some help?
Visit www.tapo.com/support/
for technical support, user guides,
FAQs, warranty & more
This product contains a coin / button cell battery. If the coin / button
cell battery is swallowed, it can cause severe internal burns in just 2
hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the
product and keep it away from children.
If you think batteries might have been swallowed or placed inside
any part of the body, seek immediate medical attention.
Risk of explosion if the battery is replaced by an incorrect type.
Warning
Warning
Do not ingest battery, Chemical Burn Hazard
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing
or cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of ammable
liquid or gas; Do not leave a battery subjected to extremely low air
pressure that may result in an explosion or the leakage of ammable liquid
or gas.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the
device. We cannot guarantee that no accidents or damage will occur due
to improper use of the device. Please use this product with care and
operate at your own risk.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be found at
https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment
Regulations 2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)
©2022 TP-Link
Loading...