Before You Start
A Tapo Hub is required. Make sure
your Tapo Hub is successfully added
via the Tapo app.
1. Power Up Your Sensor1
Remove the battery insulation tab to power
up your sensor. The LED should blink.
Note: If the LED is not blinking, refer to the reverse side for reset
instructions.
2. Set Up Your Sensor
2
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete
setup.
3. Test Your Sensor3
Take your sensor to the preferred location
and wave your hand in front of the sensor
to test it. The Tapo app should show if the
sensor is triggered.
4. Place Your Sensor4
Option 1:
Magnetically attach to
metallic objects
Option 2:
Stick to a clean wall with
included adhesive
Option 3:
Place it on a shelf
or table
Detection Area
The sensor should be aligned with the detection area and placed as close as possible to
the edge of a table or cabinet. The installation height should not be higher than 2 meters.
OR
OR
Metallic Object Adhesive
3M
3M
OR
2m
120°
7m5m1m
Side View Top View
7m5m1m
Meet Your Motion Sensor
The Motion Sensor detects movement in a certain area and triggers dierent
actions in response. This makes your home safer and smarter.
Reset
Button
Sensor
Detector
LED
Cover
Mounting
Stand
+
CR2450
Battery
Compartment
How to replace the battery
How to reset your sensor
?
Option 1: With a Shim
1
3
2
CR2450
+
4 4
1 2
OR
3
Option 2: By Hand
CR2450
+
Use a pin to press and hold the Reset
button for 5 seconds until the front LED
starts blinking.
5s
Need some help?
Visit www.tapo.com/support/
for technical support, user guides,
FAQs, warranty & more
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell battery is
swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep
it away from children.
If you think batteries might have been swallowed or placed inside any part of the body,
seek immediate medical attention.
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing or cutting
of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding environment that
can result in an explosion or the leakage of ammable liquid or gas; Do not leave a
battery subjected to extremely low air pressure that may result in an explosion or the
leakage of ammable liquid or gas.
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC,
2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be found at
https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
©2022 TP-Link
Quick Start Guide
Smart Motion Sensor
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/
setup-video/#smart-sensors
7106509752 REV1.2.1 Images may dier from actual products.
Loading...