Toyota Sequoia 2002 Owners Manual

ᘽȧᝌᛆU
For your safety and comfort,
read carefully and keep in the vehicle.
02_SEQUOIA_U (L/O 0108)
Foreword
Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and quality construction of each vehicle we build.
This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For important information about this manual and your Toyota, read the following pages carefully.
When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your complete satisfaction. He will provide quality maintenance and any other assistance you may require.
If there is not a Toyota dealer near you, or you need emergency assistance for any reason, please call the following number:
U.S. OWNERS: Toyota Cus tomer Assis tance Center Toll−free:1−800−331−4331CANADIAN OWNERS: Toyota Canada Cus tomer Interac tion Centre Toll−free:1−888−TOYOTA−8 (1−888−869−6828)
Please leave this Owner’s Manual in this vehicle at the time of resale. The next owner will need this information also.
All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of continual product improvement, we reserve the right to make changes at any time without notice.
Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle.
© 2001 TOYOTA MOTOR CORPORATION
All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor Corporation.
i
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
Important information about this manual
Safety and vehicle damage warnings
Throughout this manual, you will see safety and vehicle dam­age warnings. You must follow these warnings carefully to avoid possible injury or damage.
The types of warnings, what they look like, and how they are used in this manual are explained as follows:
CAUTION
This is a warning against something which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk to yourself and other people.
NOTICE
This is a warning against something which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment.
Safety symbol
When you see the safety symbol shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.
ii
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
Important information about your Toyota
New vehicle warranty
Your new vehicle is covered by the following Toyota limited warranties:
New vehicle warranty
Emission control systems warranty
 
Others
For further information, please refer to the “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement”.
Your responsibility for
maintenance
It is the owner’s responsibility to make sure that the specified maintenance is performed. Section 6 gives de­tails of these maintenance requirements. Also included in Section 6 is general maintenance. For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.
Accessories, spare parts and
modification of your Toyota
A wide variety of non−genuine spare parts and accesso­ries for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their perfor­mance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
This vehicle should not be modified with non−genuine Toyota products. Modification with non−genuine Toyota products could affect its performance, safety or durabili­ty, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.
iii
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
Spark ignition system of your
Toyota
The spark ignition system in your Toyota meets all re­quirements of the Canadian Interference−Causing Equip­ment Standard.
Installation of a mobile
two−way radio system
As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as multiport fuel injection system/sequential multiport fuel injection system, electronic throttle control system, cruise control system, anti−lock brake system, traction control system (four−wheel drive models)/active traction control system (two−wheel drive models), vehicle skid control system, SRS airbag system and seat belt preten­sioner system, be sure to check with your Toyota dealer for precautionary measures or special instructions re­garding installation.
Scrapping of your Toyota
The SRS airbag and front seat belt pretensioner devices in your Toyota contain explosive chemicals. If the ve­hicle is scrapped with the airbags and pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you dispose of your vehicle.
iv
2002 MY SEQUOIA_U (OM34418U)
On−pavement and off−road
driving tips
This vehicle belongs to the utility vehicle class. Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle will handle and maneuver differently from an ordinary passenger car be­cause it is designed for off−road use also. In addition, this vehicle has a higher ground clearance and center of gravity than that of an ordinary passenger car. This vehicle design feature causes this type of vehicle to be more likely to rollover. Failure to operate this vehicle correctly may result in loss of control, accidents or vehicle rollover causing death or serious injury. Be sure to read “Off−road vehicle precautions” on page 212 in Section 2 and “Off−road driving precautions” on page 230 in Section 3.
02_SEQUOIA_U (L/O 0108)
v
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
vi
2002 MY SEQUOIA_U (OM34418U)
Table of contents
02_SEQUOIA_U (L/O 0108)
1 OPERATION OF INSTRUMENTS AND CONTROLS Page
1 O verview of instruments and controls 1. . . . . . . . . . . . . . . . . . . . . . . . . .
2 Keys and Doors 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Seat s , Seat belts, Steering wheel and Mirrors 35. . . . . . . . . . . . . . . . . .
4 Light s, Wipers and Defogger 109. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 G auges, Meters and Service reminder indicators 121. . . . . . . . . . . . . .
6 Ignition switch, Transmission and Parking brake 131. . . . . . . . . . . . . .
7 Car audio system 151. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 A ir conditioning system 171. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 Other equipment 183. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 INFORMATION BEFORE DRIVING YOUR TOYOTA 211. . . . . . . . . .
3 STARTING AND DRIVING 227. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 IN CASE OF AN EMERGENCY 243. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 CORROSION PREVENTION AND APPEARANCE CARE 263. . . . .
6 VEHICLE MAINTENANCE AND CARE 271. . . . . . . . . . . . . . . . . . . . . . .
7 DO−IT−YOURSELF MAINTENANCE
1 I ntroduct ion 277. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Engine and Chassis 283. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 E lect r ical components 295. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 SPECIFICATIONS 307. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 REPORTING SAFETY DEFECTS FOR U.S. OWNERS AND
UNIFORM TIRE QUALITY GRADING 317. . . . . . . . . . . . . . . . . . . . . . . . . .
10 INDEX 321. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vii
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
viii
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
SECTION 11
OPERATION OF INSTRUMENTS AND CONTROLS
Overview of instruments and controls
Instrument panel overview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument cluster overview 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator symbols on the instrument panel 5. . . . . . . . . . . . . . . . . . . . . . .
2002 MY SEQUOIA_U (OM34418U)
1
Instrument panel overview
02_SEQUOIA_U (L/O 0108)
1. Side vents
2. Instrument cluster
3. Center vents
4. Multi−information display
5. Personal lights
6. Garage door opener box or auxiliary box
7. Electric moon roof switches
8. Side defros ter outlet
9. Glove box
10. Power door lock switches
11. Power window switches
12. Power outlets
13. Seat heater switches
14. Rear console box
15. Rear air conditioning controls
16. Cup holders
17. Power rear view mirror control switches
18. Front drive control lever
19. Lower vent
20. Hood lock release lever
21. Parking brake pedal
22. Window lock switch
2
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
1. Power back window switch
2. Headlight and turn signal switch, and front fog light switch
3. Wiper and washer switches
4. Automatic transmission selector lever
5. Emergency flasher switch
6. Car audio
7. Air conditioning controls
8. Front passenger’s seat belt reminder light
9. Back window and rear view mirror defogger switch
10. Clock
11. Cup holder
12. “VSC OFF” switch (four−wheel drive models)
13. “TRAC OFF” switch (two−wheel drive models)
14. “4WD” switch
15. Ashtray
16. Cigarette lighter
17. Cruise control switch
18. Ignition switch
19. Tilt steering lock release lever
20. Instrument panel light control knob
2002 MY SEQUOIA_U (OM34418U)
3
Instrument cluster overview
02_SEQUOIA_U (L/O 0108)
1. Oil pressure gauge
2. Service reminder indicators and indicator lights
3. Tachometer
4
4. Speedometer
5. Volt meter
6. Fuel gauge
2002 MY SEQUOIA_U (OM34418U)
7. Trip meter reset knob
8. Odometer and two trip meters
9. Engine coolant temperature gauge
Indicator symbols on the instrument panel
Brake system warning light
Driver’s seat belt reminder light
1
1
02_SEQUOIA_U (L/O 0108)
Vehicle skid control system/traction control system (two−wheel drive models) or active traction control system (four−wheel drive models) warning light
1
Front passenger’s seat belt reminder light
Discharge warning light
Malfunction indicator lamp
Low fuel level warning light
or
Anti−lock brake system warning light
1
1
1
1
1
Open door warning light
SRS warning light
Unengaged “Park” warning light
Automatic transmission fluid temperature warning light
Low windshield washer fluid level warning
1
light
1
1
1
1
Engine immobiliser/theft deterrent system indicator light
2002 MY SEQUOIA_U (OM34418U)
5
Turn signal indicator lights
Headlight high beam indicator light
Overdrive−off indicator light
Automatic transmission indicator lights
Four−wheel drive and center differential lock indicator lights
Slip indicator light
Traction control system off indicator light
1
(two−wheel drive models)
02_SEQUOIA_U (L/O 0108)
1
: For details, see “Service reminder indicators and warning
buzzers” on page 125 in Section 1−5.
2
: If this light flashes, see “Cruise control” on page 148 in
Section 1−6.
Vehicle skid control system off indicator light
1
(four−wheel drive models)
Cruise control indicator light
6
2
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
SECTION 12
OPERATION OF INSTRUMENTS AND CONTROLS
Keys and Doors
Keys 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine immobiliser system 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side doors 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power windows 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power back window 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back door 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Theft det errent system 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank cap 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric moon roof 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2002 MY SEQUOIA_U (OM34418U)
7
Keys
02_SEQUOIA_U (L/O 0108)
Since the side doors can be locked with­out a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.
For information on use of the wireless remote control key, see “Side doors” on page 12 in this section.
Your vehicle is supplied with the two kinds of keys.
1. Master key (black)—This key works in every lock. Your Toyota dealer will need it to make you a new key with built−in transponder chip.
2. Sub key (gray)—This key also works in every lock.
A transponder chip for engine immobiliser system has been filled in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.
8
NOTICE
When using a key containing a trans­ponder chip, observe the following precautions:
z When starting the engine, do not
use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.
2002 MY SEQUOIA_U (OM34418U)
z When starting the engine, do not
use the key with other transponder keys around (including keys of oth­er vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after taking off other transponder keys (includ­ing keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.
02_SEQUOIA_U (L/O 0108)
z Do not bend the key grip.
z Do not cover the key grip with any
material that cuts off electromagnet­ic waves.
z Do not knock the key hard against
other objects.
z Do not leave the key exposed to
high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.
z Do not put the key in water or
wash it in an ultrasonic washer.
z Do not use the key with electromag-
netic materials.
2002 MY SEQUOIA_U (OM34418U)
9
02_SEQUOIA_U (L/O 0108)
Engine immobiliser system
KEY NUMBER PLATE Your key number is shown on the plate.
Keep the plate in a safe place such as your wallet, not in the vehicle.
If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number.
We recommend you to write down the key number and keep it in safe place.
10
The engine immobiliser system is a theft prevention system. When you in­sert the key in the ignition switch, the transponder chip in the key’s head transmits an electronic code to the ve­hicle. The engine will start, only when the electronic code in the chip corre­sponds to the registered ID code for the vehicle.
2002 MY SEQUOIA_U (OM34418U)
The system is automatically set when the key is removed from the ignition switch. The indicator light will start flashing to show the system is set.
If any of the following indicator conditions occurs, contact your Toyota dealer.
The indicator light stays on except
when the theft deterrent system is set­ting or activating. (See “Theft deterrent system” on page 29 in this section.)
The indicator light does not start flash-
ing when the key is removed from the ignition switch.
The indicator light flashes unsteady.
02_SEQUOIA_U (L/O 0108)
Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off.
For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you.
If you make your own duplicate key, you will not be able to cancel the sys­tem or start the engine.
NOTICE
Do not modify, remove or disas­semble the engine immobiliser sys­tem. If any unauthorized changes or modifications are made, the proper operation of the system cannot be guaranteed.
For vehicles sold in U.S.A.
FCC ID: MOZ RI−4ETY MADE IN JAPAN
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ­ing interference that may cause unde­sired operation.
CAUTION
Changes or modifications not ex­pressly approved by the party respon­sible for compliance could void the user’s authority to operate the equip­ment.
For vehicles sold in Canada
This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause interfer­ence, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
2002 MY SEQUOIA_U (OM34418U)
11
Side doors
LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn
it.
To lock: Turn the key forward. To unlock: Turn the key backward.
All the side doors and back door lock and unlock simultaneously with either front side door. In the driver’s door lock, turn­ing the key once will unlock the driver’s door and twice in succession will unlock all the side doors and back door simulta­neously.
02_SEQUOIA_U (L/O 0108)
This double key turning operation to un­lock all the side doors and back door can be changed to a single key turning opera­tion. For details, contact your Toyota deal­er.
When all the side doors and back door are unlocked simultaneously with a key, the interior light, luggage compartment light, ignition switch light and foot light come on for about 15 seconds and then fade out, even if the door is not opened. (For details, see “Center interior and per­sonal lights” on page 115, “Luggage compartment light” on page 116 and “Igni­tion switch light” on page 117 in Section 1−4.)
The windows and electric moon roof can be opened or closed with the key opera­tion in the driver’s door keyhole. (For de­tails, see “Power windows” on page 22 and “Electric moon roof” on page 32 in this section.)
LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward. To unlock: Pull the knob backward.
The both front doors can be opened from the inside even with the lock knob in the locked position.
Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve­hicle.
12
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
The front side doors cannot be locked if you leave the key in the ignition switch.
Driver’s side
LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH
Push the switch.
To lock: Push the switch on the front side. To unlock: Push the switch on the rear side.
All the doors lock or unlock simultaneous­ly.
When the front side doors are locked from the outside or locked with the wireless remote control transmitter, the power door lock switch will not work until either front door is unlocked with the key, lock knob, or wireless remote control transmitter.
If the vehicle is subjected to a severe impact from the front or rear, or from either side with the ignition switch at the “ON” position, all the door locks are auto­matically cancelled.
Passenger’s side
2002 MY SEQUOIA_U (OM34418U)
13
REAR DOOR CHILD−PROTECTORS Move the lock lever to the “LOCK”
position as shown on the label.
This feature allows you to lock a rear door so it can be opened from the outside only, not from inside. We recommend us­ing this feature whenever small children are in the vehicle.
02_SEQUOIA_U (L/O 0108)
CAUTION
Before driving, be sure that the doors are closed and locked, especially when small children are in the ve­hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve­hicle during an accident. It also helps prevent the doors from being opened unintentionally.
—Automatic door locking and unlocking functions
You can select the following modes of the automatic locking and unlocking functions. The initial mode is mode 1.
Mode 1—Automatic locking operation
linked to shift lever position
All doors are automatically locked when the shift lever is moved out of “P” position after the ignition switch is turned to the “ON” position and all the doors are closed.
Mode 2—Automatic locking operation
linked to vehicle speed
All doors are automatically locked when the vehicle speed goes above about 20 km/h (12 mph).
Mode 3—Automatic unlocking opera-
tion linked to the ignition switch
All doors are automatically unlocked when the driver’s door is opened within 10 seconds after the ignition switch is turned to the “ACC” or “LOCK” posi­tion, or the key is removed.
Mode 4—Automatic unlocking opera-
tion linked to shift lever position
All doors are automatically unlocked when the selector lever is moved to “P” position after the ignition switch is turned to “ON” position.
14
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
SETTING FUNCTIONS You can set the following functions by
yourself. To set the mode 1 (the automatic lock-
ing operation linked to shift lever posi­tion):
1. Set the parking brake, close all doors and turn the ignition switch to the “ON” position.
2. Shift the selector lever into the “P” position.
3. Press the driver’s side power door lock switch on the front side for about 5 seconds, within 10 seconds after the ignition switch is turned to the “ON” position.
4. The doors will be locked and unlocked to indicate that the function is set.
To cancel the function, do the above op­eration again.
To set the mode 2 (the automatic lock­ing operation linked to vehicle speed):
1. Set the parking brake, close all doors and turn the ignition switch to the “ON” position.
2. Shift the selector lever from the “P” into the “N” position.
3. Press the driver’s side power door lock switch on the front side for about 5 seconds, within 10 seconds after the ignition switch is turned to the “ON” position.
4. The doors will be locked and unlocked to indicate that the function is set.
To cancel the function, do the above op­eration again.
To set the mode 3 (the automatic un­locking operation linked to the ignition switch):
1. Set the parking brake, close all doors and turn the ignition switch to the “ON” position.
2. Shift the selector lever from the “P” into the “N” position.
3. Press the driver’s side power door lock switch on the rear side for about 5 seconds, within 10 seconds after the ignition switch is turned to the “ON” position.
4. The doors will be locked and unlocked to indicate that the function is set.
To cancel the function, do the above op­eration again.
To set the mode 4 (the automatic un­locking operation linked to shift lever position):
1. Set the parking brake, close all doors and turn the ignition switch to the “ON” position.
2. Shift the selector lever into the “P” position.
3. Press the driver’s side power door lock switch on the rear side for about 5 seconds, within 10 seconds after the ignition switch is turned to the “ON” position.
4. The doors will be locked and unlocked to indicate that the function is set.
To cancel the function, do the above op­eration again.
CAUTION
To prevent an accident, set and can­cel the function with the parking brake set securely.
2002 MY SEQUOIA_U (OM34418U)
15
—Wireless remote control
Locking operation
Unlocking operation
02_SEQUOIA_U (L/O 0108)
The wireless remote control system is designed to lock or unlock all the side doors and back door, or activate the “PANIC” mode from a distance within approximately 1 m (3 ft.) of the vehicle.
LOCKING AND UNLOCKING THE SIDE DOORS AND BACK DOOR
To lock and unlock all the side doors and back door, push the switches slow­ly and securely.
To lock: Push the “LOCK” switch. All the side doors and back door are locked si­multaneously. At this time one beep will be heard, and the parking lights and tail lights flash once.
Check to see that all the side doors and back door are securely locked.
If any of the side doors or back door is not securely closed, locking cannot be performed by the “LOCK” switch and a beep will sound continuously for 10 sec­onds. However, if the key is in the igni­tion, a beep will not sound.
To stop the buzzer, close all the doors securely or push the “UNLOCK” switch.
The buzzer can be disabled. For details, contact your Toyota dealer.
To unlock: Push the “UNLOCK” switch once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the side doors and back door simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the parking lights and tail lights flash twice.
This double switch operation to unlock all the side doors and back door can be changed to a single switch operation. For details, contact your Toyota dealer.
When all the side doors and back door are unlocked simultaneously with a wire­less remote control transmitter, the interior light, luggage compartment light, ignition switch light and foot light come on for about 15 seconds and then fade out, even if the door is not opened. (For details, see “Center interior and personal light” on page 115, “Luggage compartment light” on page 116 and “Ignition switch light” on page 117 in Section 1−4.)
You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the side doors and back door will be automati­cally locked again.
16
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
The timing for the automatic door lock function can be changed. For details, con­tact your Toyota dealer.
If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking opera­tion is not repeated. Release the button and then push again.
The wireless door locking or unlocking function can be erased. For details, con­tact your Toyota dealer.
SWITCHING BEEP SOUND ON AND OFF
You can switch the beep on and off. (The beep is on initially and after battery re­placement .)
To switch the beep on and off: With the driver’s door opened—
1. Insert the ignition key and remove it.
2. Within 5 seconds, insert the ignition key again and turn it to the “ON” posi­tion.
3. After 10 seconds, push the same “LOCK”, “UNLOCK”, “PANIC” switch or back window open button twice within 10 seconds. Two beep sounds inform you that the program has been switched on or off.
If this procedure is not followed exactly, the beep will not operate as expected.
Check the beep ON/OFF operation by pushing the transmitter switch after you finish this procedure. If the beep does not operate as expected, repeat this proce­dure from step 1.
2002 MY SEQUOIA_U (OM34418U)
OPENING THE BACK WINDOW To open the back window, push the
back window open switch of the trans­mitter for about 1 second. The window will fully open.
At this time, you can hear a beep. If the ignition switch is in the “ON” posi-
tion, the back window cannot be opened by the back window open switch.
To open the back window with the master key, see “Power back window” on page 25 in this section.
The back window opening program by wireless remote control can be changed or disabled. For details, contact your Toyota dealer.
17
02_SEQUOIA_U (L/O 0108)
“PANIC” SWITCH Pushing the “PANIC” switch blows the
horn intermittently and flashes the headlights and tail lights.
The “PANIC” switch is used to deter ve­hicle theft when you witness anyone at­tempting to break into or damage your vehic le.
The alarm will last for one minute. To stop alarm midway, push the “PANIC” or “UNLOCK” switch, or unlock any side door or back door with key. You can also stop the alarm by turning the ignition key from “LOCK” to the “ON” position.
The “PANIC” mode does not work when the ignition key is in the “ON” position.
This alarm function can be disabled. For details, contact your Toyota dealer.
WIRELESS REMOTE CONTROL TRANSMITTER
The wireless remote control transmitter is an electronic component. Observe the fol­lowing instructions in order not to cause damage to the transmitter.
Do not leave the transmitter on places
where the temperature becomes high such as on the dashboard.
Do not disassemble it.Avoid knocking it hard against other
objects or dropping it.
Avoid putting it in water.
You can use up to 4 wireless remote con­trol transmitters for the same vehicle. Contact your Toyota dealer for detailed information.
If the wireless remote control transmitter does not actuate the doors or operate from a normal distance:
Check for closeness to a radio trans-
mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.
The battery may have been consumed.
Check the battery in the transmitter. To replace the battery, see following “REPLACING THE BATTERY”.
If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an acci­dent. (See “If you lose your wireless re­mote control transmitter” on page 261 in Section 4.)
18
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
For vehicles sold in U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ­ing interference that may cause unde­sired operation.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec­tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc­tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer­ence to radio or television reception, which can be determined by turning the equipment off and on, the user is en­couraged to try to correct the interfer­ence by one or more of the following measures :
Reorient or relocate the receiving an-
tenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced
radio / TV technician for help.
FCC WARNING: Changes or modifications not ex­pressly approved by the party respon­sible for compliance could void the user’s authority to operate the equip­ment.
2002 MY SEQUOIA_U (OM34418U)
19
02_SEQUOIA_U (L/O 0108)
For vehicles sold in Canada
Operation is subject to the following two conditions:
(1) this device may not cause interfer­ence, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
REPLACING THE BATTERY
For replacement, use a lithium battery CR2016.
CAUTION
Special care should be taken that small children do not swallow the re­moved battery or components.
NOTICE
z When replacing the transmitter bat-
tery, be careful not to lose the com­ponents.
z Replace only with the same or
equivalent type recommended by the manufacturer.
z Dispose of used batteries according
to the local laws.
Replace the battery by the following pro­cedures :
1. Using a coin or equivalent, open the transmitter case.
20
2002 MY SEQUOIA_U (OM34418U)
02_SEQUOIA_U (L/O 0108)
z Be careful that dust or oils do not
adhere to the transmitter case.
z Close the transmitter case securely.
After replacing battery, check that the transmitter operates properly. If the trans­mitter still does not operate properly, con­tact your Toyota dealer.
2. Remove the discharged transmitter bat­tery.
3. Put a new transmitter battery with posi­tive (+) side up.
Close the transmitter case securely.
NOTICE
z Make sure the positive and negative
side of the transmitter battery should be faced correctly.
z Do not replace the battery with wet
hands. Water may cause unexpected rust.
z Do not touch or move any compo-
nents inside of the transmitter, or it may interfere with proper opera­tion.
2002 MY SEQUOIA_U (OM34418U)
21
Loading...
+ 310 hidden pages