TOA Electronics F-240W, F-160WP, F-160W, F-160G, F-240G, F-240GM, F-160GM, F-160WM, F-240WM User Manual

503.3 Kb

INSTRUCTION MANUAL

F SERIES SPEAKER SYSTEM

F-160G/F-160W

(Low impedance)

F-160GM/F-160WM

(High impedance)

F-160WP (High impedance/outdoor use)

F-240G/F-240W

(Low impedance)

F-240GM/F-240WM

(High impedance)

TABLE OF CONTENTS

 

1.

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

2.

DIMENSIONAL DIAGRAM AND NOMENCLATURE . . . . . .

3

3.

HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .

4

4. FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

5.

OVERLOAD PROTECTION CIRCUITRY INFORMATION

4

6.

IMPEDANCE CHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

7. REAR COVER USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

8.

LOGO BADGE REORIENTATION . . . . . . . . . . . . . . . . . . . . .

6

9.

OUTDOOR USE (F-160WP ONLY) . . . . . . . . . . . . . . . . . . . .

6

10. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7

11. CHARACTERISTIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . .

8

Thank you for buying the TOA speaker system.

Please read this manual carefully to get the best performance from this speaker.

TOA Corporation

1. SAFETY PRECAUTIONS

Be sure to read the instructions in this section carefully before use.

Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included.

We also recommend you keep this instruction manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages are used in this manual to prevent bodily injury and property damage which

could result from mishandling. The conventions of the symbols and messages are described below. Before

doing anything else, read this manual first so you are thoroughly aware of the potential safety hazards as well as understand the safety symbols and messages. Then before operating your product, read through the instruction manual so you are familiar with its general operation.

Symbols

Symbols of caution actions

Symbols of prohibited actions

CAUTION

PROHIBITION

Indicates a potentially hazardous situation which, if mishandled, WARNING could result in death or serious personal injury.

When Installing the Unit

Install the unit only in a location that can structurally support the weight of the unit and

 

the mounting bracket. Doing otherwise may result in the speaker falling down and

 

causing personal injury and/or property damage.

CAUTION

 

 

CAUTION

Indicates a potentially hazardous situation which, if mishandled,

could result in moderate or minor personal injury, and/or

property damage.

 

When the Unit is in Use

 

Do not stand or sit on a speaker as this may cause it to fall down or drop, resulting in

 

personal injury and/or property damage.

 

 

 

 

PROHIBITION

Do not operate the speaker for an extended period of time with the sound distorting.

 

This is an indication of a malfunction, which in turn can cause heat to generate and

 

result in a fire.

 

PROHIBITION

2

2. DIMENSIONAL DIAGRAM AND NOMENCLATURE

F-160 Series

(Unit: mm)

Push terminal

Push terminal

M5 screw mounting hole x 2

 

Depth: 14 (Top panel only)

 

Tweeter

Bass-reflex duct Woofer

F-240 Series

Low-impedance models

High-impedance models

Rotary switch

F-160G/F-160W

F-160GM/F-160WM/F-160WP

 

[Rear panel without a rear cover]

 

 

 

Cable feed slot

 

Rear cover

M5 screw mounting hole x 2

 

Depth: 14

(Unitmm)

Push terminal

Push terminal

M5 screw mounting hole x 2

Depth: 14 (Top panel only)

Low-impedance models

High-impedance models

Rotary switch

 

F-240G/F-240W

F-240GM/F-240WM

 

[Rear panel without a rear cover]

Cable feed slot

Tweeter

Bass-reflex duct

Woofer

Rear cover M5 screw mounting hole x 2

 

 

 

Depth: 14

3

3. HANDLING PRECAUTIONS

Use optional mounting brackets when mounting the speaker to the ceiling or wall.

Avoid using the speaker on the beach because the speaker's life can be greatly shortened by sea breezes.

TOA takes no responsibility for any accident or equipment failure due to inadequate installation places or incorrect installation methods or disassembly or modifications carried out for the purposes other than repair

service.

The F series speaker is not magnetically shielded. Install it as far away as possible from color televisions or

video monitors to avoid degradation in television picture quality.

4. FEATURES

Two-way bass-reflex system.

High efficiency, wide range, and high input power handling capacity.

F-160 series: High power capacity 13 cm woofer with a large 90 mm magnetic circuit, and high-efficiency

3 cm dome tweeter with a large 70 mm magnetic circuit.

F-240 series: High power capacity 16 cm woofer with a large 90 mm magnetic circuit, and high efficiency 3 cm dome tweeter with a large 70 mm magnetic circuit and a titanium diaphragm.

The tweeter employs a constant directivity horn which ensures uniform sound dispersion of 90 ° horizontal and 90° vertical.

Independent built-in overload protection circuitry for woofer and tweeter. (Low-impedance models only) A detachable rear cover cleanly conceals the speaker terminals.

Acoustically efficient polypropylene enclosure.

Optional wall and ceiling mounting brackets.

F-160WP: Drip-proof construction makes the speaker system ideal for outdoor use.

5. OVERLOAD PROTECTION CIRCUITRY INFORMATION

(LOW-IMPEDANCE MODELS ONLY)

The F-160G, F-160W, F-240G, and F-240W have a built-in overload protection circuitry.

If the excessive input is applied to a woofer or tweeter, the overload protection circuitry is activated and cuts off the signal supply to the speaker component.

A sudden drop of the volume level of either the high or low frequencies during speaker operation indicates that the overload protection circuitry has been activated. In such a case, reduce the amplifier volume and just

wait. The protection circuitry is automatically reset after approximately 3-30 seconds. After the circuitry is reset, set the volume at a lower level than before.

[Important Note]

This overload protection circuitry does not perfectly protect the speaker component. Depending upon the

excessive input to be applied, the protection circuitry may not operate, causing damage to the speaker component. In addition, the circuitry may not be restored to the previous state if the excessive input is applied

continuously for long time. Take special care that the excessive input is not applied to the speaker during use.

4

6. IMPEDANCE CHANGE (HIGH-IMPEDANCE MODELS ONLY)

Because the following models have a built-in matching transformer, connect them to the amplifier with a

high-impedance (70 or 100) line output.

F-160GM, F-160WM, F-160WP, F-240GM and F-240WM

Input impedance can be switched in five steps, as

Rotary switch

2 k

5 W

2.5 W

shown in the table at right (factory-preset to 330

 

1 k

10 W

5 W

ohms). To change, set the rotary switch to the

 

 

500

20 W

10 W

desired impedance using a screwdriver blade.

 

330

30W

15 W

 

 

NC

 

 

[Note]

 

170

 

30W

When using the 100 line, never set the impedance to 170 ohms. The speaker itself or the power amplifier may be damaged.

7. REAR COVER USAGE

F Series speakers feature a rear cover that cleanly

conceals the speaker terminals on the rear panel.

To remove the cover, insert a finger in the line feed slot and pull the cover away from the speaker. To reattach, simply snap the cover back into place.

If required, the positioning of the cover's line feed slot can be easily reversed by snapping the cover on

"upside down".

Model F-160WP must be mounted with the line feed

slot facing down.

Cable feed slot

Rear cover

F Series speaker

Speaker cable

Rear cover

 

Upward speaker cable routing

Downward speaker cable routing

(Line feed slot faces up.)

(Line feed slot faces down.)

5

8. LOGO BADGE REORIENTATION

The speaker's front grille logo badge is attached with double-sided tape. To change its orientation, carefully peel the

logo off the grille and stick it back on again in the same location

in the desired orientation.

Speaker grille

 

Logo badge

9. OUTDOOR USE (F-160WP ONLY)

 

Model F-160WP can be permanently installed outdoors, and

other F Series speakers cannot.

Rear cover

In the F-160WP, the rear cover prevents water from getting

into the terminal section. When installing the

F-160WP

outdoors, make sure that the rear cover is mounted with the line feed slot facing down.

If using a thicker speaker cable that does not easily fit through

the rear cover's cable guide, use a knife to cut out the rubber

cable guide along the imprinted groove, as shown in the

illustration at right.

[Note]

When mounting model F-160WP on the wall or under the eaves, be sure to use optional outdoor mounting brackets. Adjust the speaker installation angle and direction within the ranges shown in the figures below:

Speaker cable

The inside of the rear cover

Cable guide

When mounting on the wall

When mounting under the eaves

 

Horizontal 0°

 

 

 

 

 

Mounting bracket

 

Install within this range.

 

Downward 15

 

Downward 45

Mounting bracket

Install within this range.

Cannot be positioned vertically.

 

Downward 60 °

Model F-160WP features drip-proof construction. However, do not dash water over it when cleaning as this

may cause damage to the speaker components.

When installing the F-160WP outdoors in a snowy area, protect the speaker by preventing snow from piling up on it.

6

10. SPECIFICATIONS

Model No.

Enclosure Type

Speaker

Low frequency High frequency

Rated Impedance

Power Handling Capacity

F-160G

F-160W

F-240G

F-240W

 

Bass-reflex type

 

13 cm cone speaker

16 cm cone speaker

3 cm dome speaker (film diaphragm)

3 cm dome speaker (titanium diaphragm)

 

 

8

 

Continuous pink noise: 50W (*)

Continuous program: 150W

Output Sound Pressure Level

91 dB (1 W/1 m)(**)

 

 

92 dB (1 W/1 m) (**)

Crossover Frequency

 

4 kHz (passive network)

 

Frequency Response

100 - 20,000 Hz ( -10 dB)

 

65 - 20,000 Hz ( -10 dB)

 

150 - 13,000 Hz ( -3 dB)

 

130 - 15,000 Hz ( -3 dB)

InputConnector

 

 

Push terminal

 

Enclosure Material

 

 

Polypropylene resin

 

Color

Dark gray

White

 

Dark gray

White

Dimensions

250 (W) x 157 (H) x 169 (D) mm

 

355 (W) x 210 (H) x 226 (D) mm

Weight

Approximately 3.3 kg

 

 

Approximately 4.9 kg

Model No.

F-160GM

F-160WM

 

F-240GM

F-240WM

Enclosure Type

 

 

Bass-reflex type

 

Speaker

13 cm cone speaker

 

 

16 cm cone speaker

Low frequency

 

 

High frequency

3 cm dome speaker (film diaphragm)

3 cm dome speaker (titanium diaphragm)

Rated Impedance

100 Line: 330

(30 W), 500

(20 W), 1 k

(10 W), 2 k

(5W)

 

70 Line:170

(30 W), 330

(15 W), 500

(10 W),1 k

(5 W), 2 k (2.5 W)

Rated Input Power

 

 

 

30W

 

 

Output Sound Pressure Level

91 dB (1 W/1 m)(**)

 

 

92 dB (1 W/1 m) (**)

Crossover Frequency

 

4 kHz (passive network)

 

Frequency Response

100 - 20,000 Hz ( -10 dB)

 

65 - 20,000 Hz ( -10 dB)

 

150 - 13,000 Hz ( -3 dB)

 

 

130 - 15,000 Hz ( -3 dB)

Input Connector

Enclosure Material

Color

Dimensions

Weight

Model No.

Enclosure Type

Speaker

Low frequency High frequency

Rated Impedance

 

Push terminal

 

 

Polypropylene resin

 

Dark gray

White

Dark gray

White

250 (W) x 157 (H) x 169 (D) mm

355 (W) x 210 (H) x 226 (D) mm

Approximately 3.9 kg

Approximately 5.5 kg

F-160WP

 

 

 

Bass-reflex type

 

 

 

13 cm cone speaker (drip-proof)

3 cm dome speaker (film diaphragm)

100 Line : 330

(30

W), 500

(20 W), 1 k

(10 W), 2 k

(5 W)

70 Line : 170

(30

W), 330

(15 W), 500

(10 W), 1 k

(5 W), 2 k (2.5 W)

Rated Input Power

30W

Output Sound Pressure Level

91 dB (1 W/1 m)(**)

Crossover Frequency

4 kHz (passive network)

Frequency Response

100 - 20,000 Hz ( -10 dB)

 

150 - 13,000 Hz ( -3 dB)

Input Connector

Push terminal

Enclosure Material

Polypropylene resin

Color

Dark gray

Dimensions

250 (W) x 157 (H) x 169 (D) mm

Weight

Approximately 3.9 kg

 

(*) Continuous 24 hours pink noise of 50 Hz - 20 kHz

 

(**) Pink noise of 330 Hz - 3.3 kHz

Specifications are subject to change without notice.

7

11. CHARACTERISTIC DIAGRAM

F-160 Series Frequency Response (1 W/1 m)

F-160 Series Directional Characteristics

 

Vertical

Horizontal

1000 Hz

2000 Hz

4000 Hz

8000 Hz

10 dB/Div.

F-240 Series Frequency Response (1 W/1 m)

F-240 Series Directional Characteristics

 

Vertical

Horizontal

1000 Hz

2000 Hz

4000 Hz

8000 Hz

10 dB/Div.

TOA Corporation

8

The manual in English is provided at the back.

F-160G, F-160W

F-160GM, F-160WM

F-160WP

F-240G, F-240W

F-240GM, F-240WM

533-06-005-80

2

3

4

5

6

7

8