Z
Installation guide for the HA-P90SD USB DRIVER
For Windows only
Supported products
HA-P90SD
Recommended hardware
PC with Intel Core 2 Duo or faster processor and 1 GB or more
memory
Supported operating systems
Windows 7 (32/64-bit)
Windows 8 (32/64-bit)
Windows 8.1 (32/64-bit)
as of January, 2015
Precautions before installation
Install the dedicated driver software before connecting
the computer by USB.
Correct operation will not be possible if you connect the computer before installing the driver.
ASIO is a trademark and software of Steinberg Media Technologies
GmbH.
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other
countries.
3 Select the language that you want to use for instal-
lation and click “OK”.
4 Click “Next”.
Other company names and product names in this document are
the trademarks or registered trademarks of their respective owners.
Driver installation procedures
ATTENTION
The V1.0.0.1 driver supports HA-P90SD V1.02 and later firmware
versions. If the unit is using an older firmware version, update the
firmware before updating the driver.
1 Uncompress the downloaded le.
2 If using a 32-bit operating system, double-click the
TEAC_HA_P90SD_AsioDriver32bit.exe le to open
the installation wizard.
If using a 64-bit operating system, double-click the
TEAC_HA_P90SD_AsioDriver64bit.exe file to open
the installation wizard.
If a Software (program) use confirmation pop-up appears, click
“Run” or “Yes” to continue with installation of the driver file.
5 After confirming the contents of the License
Agreement, select “I accept the terms in the license
agreement” and click “Next”.
D01259810B
Continued on the next page e
1
Z
Installation guide for the HA-P90SD USB DRIVER
6 Click “Install”.
7 If a Windows security pop-up message appears
during installation, click “Install” or “Continue
A n y w a y ”.
Windows 8.1, Windows 8 and Windows 7
Connecting with a computer
The first time the unit is connected to one of the computer's USB
ports, a driver will be detected automatically.
The contents of the driver software installation window will change
as follows.
c
Display example
8 When the wizard's completion screen appears, click
“Finish” to nish the installation.
c
When “ Ready to use” appears, click “Close” to finish the installation.
2
Z
If the connected unit has been recognized properly, when you
open the Windows Sound Control Panel, “HA-P90SD” will have been
added as a playback device.
Windows 7 example
Installation guide for the HA-P90SD USB DRIVER
Setting the audio output device
When you open the Windows Sound Control Panel, the “HA-P90SD“
can be selected as the default device for sound playback.
The device selected here will be used to output Windows operation
sounds and the sound of playback from Windows Media Player.
When using Windows 8.1, Windows 8 or Windows 7,
you must change the settings as follows to set the
default device for sound playback.
1 After selecting “HA-P90SD” on the Sound Playback
screen, click “Properties”.
2 Click the Advanced tab at the top of the Speakers
Properties screen.
Click the field that shows the “Default Format” setting to open a
pull-down menu and select a sampling frequency of 192000Hz
or less.
3 Click “OK” to conrm the setting.
Continued on the next page e
3
Z
Installation guide for the HA-P90SD USB DRIVER
HA-P90SD Control Panel
If the computer being used meets the minimum system requirements, making the following adjustment should not be necessary.
If the playback sound is unstable due to the system being used,
increasing the buffer size might correct this.
Click the following icon in the Windows Control Panel.
The following window will appear.
If necessary, move the slider (inside the red box in the window
shown below) to change the buffer size.
Update history
V1.0.0.1
Sometimes a slight noise occurs immediately after starting playback,
pausing or between tracks during continuous playback, for example. This has been reduced.
Music playback software settings
To output audio from music playback software from this unit when
connected to a computer by USB, set the sound playback device to
“HA-P90SD“ in the settings of the software that you are using.
See the instructions for that software for details about how to set
the sound playback device.
If the software does not have a sound output device setting, usually
sound will be output from the device selected as the Default Device
set for Windows sound playback as described above.
o If you only want the sound from specific software to be output
from this unit, select “HA-P90SD” in the settings of that software,
but do not set “HA-P90SD” as the Default Device for sound playback in the Windows Sound Control Panel.
4
0315 MA-2157B
Loading...