TEAC AG-H600NT Owner's Manual

D01039120B

AG-H600NT

Stereo Receiver

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

ENGLISH

FRANÇAIS

ESPAÑO L

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip -over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

L’utilization de ce dispositif est au to risée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout

brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.

ENGLISH

< Do not expose this apparatus to drips or splashes. < Do not place any objects filled with liquids, such as vases, on the

apparatus.

< Do not install this apparatus in a confined space such as a book

case or similar unit.

< The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON position.

< The apparatus should be located close enough to the AC outlet

so that you can easily grasp the power cord plug at any time.

< The mains plug is used as the disconnect device, the disconnect

device shall remain readily operable.

< Products with Class I construction are equipped with a power

supply cord that has a 3-prong grounding plug. The cord of such a product must be plugged into an AC outlet that has a protective grounding connection.

< If the product uses batteries (including a battery pack or installed

batteries), they should not be exposed to sunshine, fire or excessive heat.

< CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an incorrec t type of battery. Replace only with the same or equivalent type.

< Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from earphones or headphones can cause hearing loss.

For U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications to the equipment not expressly approved by TEAC CORPORATION for compliance could void the user’s authority to operate this equipment.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE WITHIN!

< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED.

CAUTION Regarding Placement

To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below.

Left and Right Panels: 20 cm (8”) Rear Panel: 10 cm (4”) Top Panel: 5 cm (2”)

In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled exposure, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC RF Radiation Exposure Statement Caution : To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.

For the LAN port, shielded cable must be used with this unit to ensure compliance with the Class B FCC limits.

iPod is a trademark of Apple Inc., registered in the U.S. and other countries. “Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft. Windows XP and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

RealAudio and the Real Enabled logo are trademarks or registered trademarks of RealNetworks, Inc.

Before Use

Thank you for choosing TEAC. Read this manual carefully to get the best performance from this unit.

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Before Use ....................................................4

Connecting Antennas (AM/FM) ................................5

Connection ...................................................6

Internet Connection ..........................................8

System Connection ...........................................8

Speaker Connection ..........................................9

Remote Control Unit ..........................................9

Parts Identification ...........................................10

Basic Operation ..............................................12

Adjusting Bass, Midrange, Treble, and Balance of Speakers .....13

Listening to iPod .............................................14

Listening to FM/AM ..........................................16

Preset Tuning ................................................17

Internet Radio Initial Setup ...................................19

Listening to Internet Radio ...................................20

Internet Radio Menu Operations ..............................22

Network Configuration .......................................23

Radio Portal ..................................................24

Setting up Music Player ......................................24

Media Player Initial Setup .....................................28

Listening to Music Player (Shared Media) ......................29

Listening to Music Player (Shared Folders) .....................30

Read this before attempting any operations.

< When the unit is turned on, switching on the TV may cause lines

to appear on the TV screen, depending on the condition of the electric waves of the TV broadcast. This is not malfunction in the unit or the TV. In this case, turn off the unit.

< As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

Make sure there is at least 20 cm of space above and at least 5 cm

of space on each side of the unit. Do not place anything on top of the unit.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding this matter, consult an electrician.

< Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibrations and excessive dust, heat, cold or moisture.

< Do not place the unit on an amplifier/receiver.

< Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into the unit, contact your dealer or service company.

< When removing the power plug from the wall outlet, always pull

directly on the plug, never yank on the cord.

< Do not attempt to clean the unit with chemical solvents as this

might damage the finish. Use a clean, dry or slightly damp cloth.

Troubleshooting .............................................31

Specifications ................................................33

< Keep this manual in a safe place for future reference.

Connecting Antennas (AM/FM)

AM Indoor Loop Antenna

The high-performance AM loop antenna provided with this unit is sufficient for good reception in most areas.

To stand the loop antenna on a surface, fix the claw to the slot in the antenna base.

Connect the loop antenna‘s wires to the AM antenna terminals.

< Make sure to connect the black wire to the GND terminal.

Place the antenna on a shelf or hang it on a window frame, etc., in the direction which gives the best reception. Keep all other wires such as power cords, speaker wires or interconnect wires as far away as possible from the antenna.

AM Outdoor Antenna

If the AM loop antenna provided does not deliver suf ficient reception (often due to being too far from the transmitter or in a concrete building, etc.), it may be necessary to use an outdoor AM antenna.

FM Indoor Antenna

Connect the lead-type FM antenna to the FM 75Ω socket, extend the lead and tune in your favourite station (page 16). Adjust the antenna in a suitable location like a window frame or wall which gives the best reception and then fix the antenna in that position with thumb tacks or the like.

ENGLISH

FM Outdoor Antenna

In an area where FM signals are weak, it will be necessary to use an outdoor FM antenna. Generally, a 3-element antenna will be sufficient; if you live in an area where the FM signals are particularly weak, it may be necessary to use one with 5 or more elements.

< Disconnect the FM indoor antenna when using an outdoor

antenna.

Use either a high quality commercially available AM antenna or, if not available, an insulated wire more than 16 ft (5 m) long, strip one end, and connect this to the terminal as shown.

The antenna wire should be strung outdoors or indoors near a window. For better reception, connect the GND terminal to a reliable ground.

< Even when using an outdoor AM antenna, do not disconnect the

AM loop antenna.

Connection

VIDEO

S-VIDEO IN

LINE OUT

LINE

RLRL

F G

CAUTION

< Connect the power plug to a wall socket after completing all other connections.

< Be sure to thoroughly read through the instruction manuals of the equipment you will connect and

observe all instructions.

TV monitor, etc.

Cassette deck,

Turntable

Connect one of these cables.

CD recorder, etc.

AG-H600NT

CD player

(PD-H600, etc.)

LINE IN/OUT jacks

These jacks transmit an analog 2-channel audio signal. Connect the components using RCA cables.

< Make sure to connect the cables as follows:

white plug q white jack (L: left channel) red plug q red jack (R: right channel)

iPod dock port

Connect the iPod dock (option) to this port.

< Make sure the label A side of the plug is up. < Securely insert the plug until a slight “click” is heard.

To disconnect the dock

Push the buttons of the plug and pull.

White (L)

Red (R)

< Be sure to insert each plug securely. To prevent hum and noise,

avoid bundling the cables together with the AC power cord or speaker cables.

PHONO jacks

Connect the turntable’s RCA pin cord to the PHONO jacks.

< Make sure to connect the cables as follows:

white plug q white jack (L: left channel) red plug q red jack (R: right channel)

< Be sure to insert each plug securely. To prevent hum and noise,

avoid bundling the cables together with the AC power cord or speaker cables.

SIGNAL GND

To prevent hum and noise, connect the ground lead of the turntable to this terminal.

< This is not a safety earth.

White (L)

Red (R)

label

Compatible iPod Software

If your iPod does not work with the unit or with the remote control unit, software update may solve the problem. Visit the Apple web site and download the latest iPod Software.

VIDEO OUT terminal

This terminal outputs video signal from iPod. Use a composite video cable to connect the dock to the composite video connector of a television or monitor.

S-VIDEO OUT terminal

This terminal outputs S-video signal from iPod. Use an S-video cable to connect the dock to the S-video input of a suitably equipped television or monitor. Use this connec tion in preference to a composite video connection.

ENGLISH

AC Inlet

Use only the supplied power cord.

< Use of other power cord may result in fire or electric shock.

< Unplug the power cord when you are not going to use the unit

for an extended period of time.

System ConnectionInternet Connection

SYSTEM CONTROL

To enjoy the Internet Radio and the Music Player function, connect the unit to the broadband internet network.

< If you can use a wireless LAN in your installation site, connect the

supplied wireless LAN antenna to the WLAN jack.

< To use a wired Internet connection, connect the Ethernet port of

this unit to the Ethernet network using a commercially available Ethernet cable.

Wireless LAN antenna

AG-H600NT

If you have TEAC compact disc player PD-H600, convenient system control functions are possible.

PD-H600

AG-H600NT

Ethernet cable

< By pressing the STANDBY/ON button on the remote control unit

(RC-1181) of AG-H600 series receiver, you can switch on/standby both AG-H600 and PD-H600. You cannot switch on/standby PD-H600 using the remote control unit (RC-1182) of PD-H600.

< When you change the source on the AG-H600 series receiver

from CD to another, playback stops on PD-H600.

When you want to use the system control functions, connect the SYSTEM CONTROL jack of each component by a system control connection cord (supplied with PD-H600), and set the SYSTEM CONTROL SELECTOR switch on the rear panel of the PD-H600 to ”SYSTEM”.

ENGLISH

Remote Control UnitSpeaker Connection

AG-H600NT

Right Speaker Left Speaker

Caution

< Check the impedance of your speakers. Connect speaker with an

impedance of between 4 ohms and 8 ohms.

< The red speaker terminals are + (positive) and the black speaker

terminals are _ (negative).

Generally, the + side of the speaker cable is marked to make

it distinguishable from the _ side of the cable. Connect the marked side to the + terminal and the unmarked side to the black _ terminal.

< The metal portions of the two separate wires should not touch

or an electrical short can occur. Shorted wires can create a fire hazard or induce a failure in your equipment.

< Be sure to insert each plug securely. To prevent hum and noise,

avoid bundling the cables together with the AC power cord or other cables.

How to connect:

1. Turn the terminal cap counterclockwise to loosen it. The speaker terminal caps cannot be fully removed from the base.

2. Insert the wire into the terminal and turn the terminal cap clockwise to securely connect it:

The provided Remote Control Unit allows the unit to be operated from a distance. When operating the remote control unit, point it towards the remote sensor on the front panel of the unit.

< Even if the remote control unit is operated within the effective

range, remote control operation may be impossible if there are any obstacles between the unit and the remote control.

< If the remote control unit is operated near other appliances which

generate infrared rays, or if other remote control devices using infrared rays are used near the unit, it may operate incorrectly. Conversely, the other appliances may operate incorrectly.

Battery Installation

1. Remove the battery compartment cover.

2. Insert two “AAA” (R03, UM-4) dry batteries. Make sure that the

batteries are inserted with their positive “+” and negative “_” poles positioned correctly.

3. Close the cover.

Battery Replacement

If the distance required between the remote control unit and main unit decreases, the batteries are exhausted. In this case replace the batteries with new ones. For more information about collection of batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

< Make sure none of the wire insulation is under the terminal and

only the bare, stripped wire is touching the terminal.

3. Make sure the cable is fastened firmly by pulling the cable lightly.

Precautions concerning batteries

< Be sure to insert the batteries with correct positive “+” and

negative “_” polarities.

< Use batteries of the same type. Never use different types of

batteries together.

< Rechargeable and non-rechargeable batteries can be used. Refer

to the precautions on their labels.

< When the remote control unit is not to be used for a long time

(more than a month), remove the batteries from the remote control unit to prevent them from leaking.

< If the batteries leak, wipe away the liquid inside the battery

compartment and replace the batteries with new ones.

< Do not use any other batteries not specified. Do not mix new

batteries with old ones or use dif ferent types of batteries together.

< Do not heat or disassemble batteries and never throw them in

the fire or water.

< Do not carry or store batteries with other metallic objects. The

battery may short circuit, leak or explode.

< Never recharge a battery unless it is a verified rechargeable type.

Parts Identification

A B C D E F G H

LJ KI

POWER

Press this switch to turn the unit on or off. The standby indicator lights orange when the unit is in the standby mode. When the unit is turned on, the indicator lights blue.

SOURCE

Press this button to select a source.

TONE DIRECT

When this button is pressed, the tone control is bypassed. Press it again to turn to normal.

INFO

While listening to the Internet Radio and Music Player, use this button to change the information on the second line of the display. Please ignore “RDS” of the remote control unit. (RDS function does not work on this unit.)

TUNING MODE

Use this button to change the tuning mode.

MEMORY

Use this button to store preset stations into memory.

Remote Sensor

When using the remote control unit, point it towards the remote sensor.

PHONES

For private listening, insert the headphones plug into this jack, and adjust the volume by turning the VOLUME/SET knob.

Display

MULTI JOG/ENTER

Turn this knob to tune in FM/AM stations or to select parameters in menus. Press this knob to enter your selection.

While listening to the Internet Radio, press this button to open menus. While listening to iPod, use this button to go back to previous menu. This button is equivalent to the MENU button on your iPod.

VOLUME/SET

Turn this knob to adjust the volume. Press this knob to adjust tones and balance.

ENGLISH

D H

c d

Stop (H)

Use this button to stop playback of PD-H600 or iPod.

SHUFFLE

Use this button to change the random mode of PD-H600 or iPod.

Skip/Scroll (.°//‡)

Use these buttons to skip tracks/files during playback of the PD-H600. Use these buttons to scroll through menu items.

Play/Pause (y/J)

Use this button to start or pause playback of the PD-H600 or iPod.

MUTING

Use this button to mute the sound.

DIMMER

You can use this button to dim the display among three levels.

Search (m/,)

Use these buttons to search for a track /file during playback of the PD-H600. Use these buttons to skip tracks during playback of the iPod.

VOLUME (+/–)

Use these buttons to adjust the volume.

Note:

To simplify explanations, instructions refer to names of buttons

STANDBY/ON

Press this button to turn the unit on or standby.

TUNER, CD, iPod, AUX , PHONO

Use these buttons to select a source.

BAND

Use this button to select FM, AM or Internet Radio.

TUNING/PRESET (‡/°)

Use these buttons to tune in FM/AM stations.

TUNING MODE/AUTO TUNING

While listening to FM or AM, use this button to change the tuning mode.

and controls on the front panel, making no mention of the use of remote control unit.

MEMORY SCAN

While listening to FM or AM, use this button to check the list of preset stations.

FM MODE

While listening to FM, use this button to selec t stereo or monaural.

RE PEAT

Use this button to change the repeat mode of PD-H600 or iPod.

421

Press the power switch to turn the unit on.

standby indicator

The standby indicator lights blue.

Basic Operation

Start playback of the component, or tune in a radio station

on this unit.

Please read the instructions of each component.

Gradually turn up the volume to the required level by

turning the VOLUME/SET knob.

Muting

Press the MUTING button to mute the sound temporarily.

< When the system control functions are activated, always set this

switch on, and turn the unit on/standby using the remote control unit.

Select a source.

Each time you press the SOURCE button or the BAND button on the remote control unit, the source changes as follows:

iPod

AUX

PHONO

SOURCE

button

< To restore the sound, press the MUTING button again.

Internet Radio

Music Player

< You can also use the TUNER, CD, iPod, AUX and PHONO buttons

on the remote control unit to select each source.

BAND

button

ENGLISH

FM CH01 98.1MHz

Adjusting Bass, Midrange, Treble, and Balance of Speakers

Select the item to adjust.

Each time you press the DIMMER button, the display changes as follows:

NORMAL (Normal)

DIMMER (Dimmed)

LIGHT OFF (Display off)

< This setting is not memorized when the unit turns into standby.

The next time the unit is turned on, the display is illuminated as normal.

Each time you press the VOLUME/SET knob, the display changes as follows:

VOLUME (volume)

BASS

MID

TREBLE

BALANCE

DIMMER

< You can also use the SET button on the remote cntrol unit.

< When the unit is operated during the setting is “LIGHT OFF“, the

display turns normal briefly and will turn off again.

Turn the VOLUME/SET knob to change the setting.

< You can also use the VOLUME buttons (+/–) on the remote cntrol

unit.

Leave the unit idle for 3 seconds to exit the setup mode.

Tone Direct

Press the TONE DIRECT button to cancel the tone adjustments temporarily.

BASS

Adjusts the level of low frequency sound range. The level can be adjusted from –12 to +12.

MID

Adjusts the level of middle frequency sound range. The level can be adjusted from –12 to +12.

TREBLE

Adjusts the level of high frequency sound range. The level can be adjusted from –12 to +12.

BALANCE

Adjusts the balance of the volume level between left and right speakers.

DIMMER

Adjusts the dimming level of the display in 3 levels using the DIMMER button of the remote control unit.

When this function gets active, the Tone Direct indicator lights up temporarily.

Tone Direct indicator

< To cancel the Tone Direct function, press the button again.

< When this function is active and no operation is done for about

5 seconds, the display is turned off regardless of the dimmer setting.

Listening to iPod

Select iPod by pressing the SOURCE button repeatedly.

Insert the iPod into the dock.

Basic operations

To suspend playback temporarily (pause mode)

During playback, press the play/pause button (G/J). Playback stops at the current position.

< To resume playback, press the play/pause button (G/J) again.

To skip to the next or a previous track

During playback, press the search buttons (m/,) repeatedly until the desired track is found.

The iPod automatically turns on and starts playback from the iPod’s music list.

< When the iPod is inserted while a source other than iPod is

selected, the iPod will turn on and enter the pause mode.

< Make sure to use an appropriate dock adapter (see “Getting

Started” on the owner’s manual of the iPod dock).

< The iPod is recharged when it is plugged into the dock and the

AG-H600 series receiver is on. While the unit is on standby, the iPod is not recharged because the unit’s power consumption is minimised to meet the regulation of IEA.

< When headphones are plugged into the iPod, sound comes

from both the speakers of the AG-H600 series receiver and the headphones.

< When the search button (m) is pressed during playback, the

current track will be played from the beginning. If you want to play the previous tracks, press the search button (m) twice or more.

To search for a part of a track

During playback, hold down the search button (m or ,) and release it when the part you want to listen to is found.

ENGLISH

Menu operations

To go back to the previous menu

Press the MENU button.

< This button is equivalent to the MENU button on your iPod.

To select the menu item

Press the scroll buttons (.°//‡) to scroll to the menu item you want, and then press the ENTER button.

Shuffle playback

Each time the SHUFFLE button is pressed, the shuffle mode changes as follows:

Song (shuffle songs)

Album (shuffle albums)

Shuffle Off

< When you select “Song“, the iPod shuffles songs within the list

you choose to play.

< On the main unit, turn the MULTI JOG/ENTER knob to scroll to the

menu item you want, and then press the MULTI JOG/ENTER knob.

Repeat playback

Each time the REPEAT button is pressed, the repeat mode changes as follows:

One (repeat one song)

All (repeat all the songs in the list)

Repeat Off

< When you select “Album“, the iPod plays all the songs on an

album in order, and then randomly selects another album in the list and plays through it in order.

< During playback, the Shuffle icon (

display.

) appears in the iPod’s

Docking an iPod to this system

iPod video output

Make the following settings on your iPod’s menu to output video to a TV via the dock. In the [Video] menu, select [Video Settings]. Set [TV OUT] to [On] or [Ask]. If you have set [TV OUT] to [Ask], your iPod prompts you each time you play a video to specify whether to output it to a TV.

Note

< If you output video to a TV from your iPod, the video is not

displayed on the iPod’s screen.

< iPod touch does not contain this menu. You will have to

specify whether to a output video to a TV each time you play it.

< When you select the “One”, the Repeat One icon (

the iPod’s display.

< When you select the “All”, the Repeat icon ( ) appears in the

iPod’s display.

) appears in

Using the alarm on your iPod touch

If you specify [Slide to power off] on your iPod touch, you cannot use the alarm even if the iPod touch is docked to this system. To use the alarm on your iPod touch, do not select [Slide to power off]. (The screen can be turned off without any problem.)

< When video is displayed on your iPod touch’s screen, you

cannot use the alarm even if the iPod touch is docked to this system. To use the alarm on your iPod touch, select any item other than video.

Listening to FM/AM

FM ¤S

< >

108.00MHz

< A >

108.00MHz

< >

108.00MHz

FM CH01 108.00MHz

Se le ct FM or AM by pr essin g th e SOU RCE but to n

repeatedly.

< You can also use the BAND button on the remote control unit.

Select the desired tuning mode.

Select the station you want to listen to.

Manual tuning mode

Turn the MULTI JOG/ENTER knob (or press the TUNING/PRESET ‡/° button on the remote control unit) until the station you want to listen to is found. The frequency changes by a fixed step (FM: 50 kHz steps, AM: 9 kHz steps).

Auto tuning mode

Turn the MULTI JOG/ENTER knob (or press the TUNING/PRESET ‡/° button on the remote control unit) to begin auto tuning. Wh en a station is found, the unit tunes in th e station automatically. Repeat this step until the station you want to listen to is found.

Each time the TUNING MODE button is pressed, the tuning mode changes as follows:

Manual tune

Auto tune

Preset tune

< Press the TUNING MODE button to stop the auto tuning.

FM Mode

Pressing the FM MODE button alternates between Stereo mode and Mono mode.

Stereo:

FM stereo broadcasts are received in stereo and the stereo indicator is displayed.

Mono:

Select this mode when the signal is weak. Reception will be forced monaural, reducing unwanted noise.

ENGLISH

Preset Tuning (1)

1 2

2 4

3 5

FM ¤S CH01 108.00MHz

FM ¤S CH12 108.00MHz

Manual Preset (FM/AM)

You can store up to 30 FM and 30 AM stations.

Se le ct AM or FM by pres sing the S OURC E bu tt on

repeatedly.

< You can also use the BAND button on the remote control unit.

Within 4 seconds, press the MEMORY button.

The station is stored.

< To store more stations, repeat steps

< If you do not press the MEMORY button within 4 seconds after

selecting the preset number, presetting will be cancelled.

to 5.

Presetting Automatically

Tune in the station you want to store.

See the previous page for the procedure of tuning.

Press the MEMORY button.

With in 4 se conds , se lec t the preset nu mbe r fo r this

station.

Turn the MULTI JOG/ENTER knob.

Se le ct FM or AM by pr essin g th e SOU RCE but to n

repeatedly.

< You can also use the BAND button on the remote control unit.

Press and hold the MEMORY but ton for more than 3

seconds.

Up to 30 of the best received stations in your area will be stored automatically.

< You can also use the TUNING/PRESET buttons (‡/°) on the

remote control unit to scroll through menu items.

FM CH01 108.00MHz

Preset Tuning (2)

How to select preset stations (FM/AM)

Se le ct FM or AM by pr essin g th e SOU RCE but to n

repeatedly.

< You can also use the BAND button on the remote control unit.

Select the preset tuning mode.

Press the TUNING MODE button repeatedly until “CH” is displayed.

Checking preset stations (FM/AM)

You can see the list of preset stations.

Press the MEMORY SCAN button while listening to FM or AM.

Preset number and its frequency is displayed in turn. The unit turns to the preset tuning mode after all the preset stations have been displayed.

Select a preset channel by turning the MULTI JOG/ENTER

knob.

The selected preset channel is tuned in.

ENGLISH

Internet Radio Initial Setup

Most of Europe USA

Key:Ge 0123456789

005AD904JM2 [Wired]

/Ò

Ú°/Æ‡

ENTER

Initial setup

When you use the Internet radio function for the first time, the unit starts an initial setup procedure to connect to the Internet.

Select Internet Radio by pressing the SOURCE button

repeatedly.

Enter the correct password for the network if required.

< See “How to input characters” below.

Now the unit starts to connect to the Internet. When connection is established successfully, the Internet radio menu is displayed. See page 20 to select a station.

< If you have a problem connecting to the Internet, see page 23.

How to input characters

< You can input characters only from the remote control unit.

< You can also use the BAND button on the remote control unit.

Initial setup wizard starts.

Select your country/area.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

Select a network name you want to use.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

1. Press the skip/scroll buttons (.°//‡) to select a set

of characters.

2. Press the search buttons (m/,) to select the character

you want to input.

3. Press the ENTER button to input the selected letter. Repeat steps 1 to 3 to input next characters.

<: Deletes the last character. E: Enters your input. C: Cancels the operation and goes back to the previous screen.

Characters you can input

0123456789 ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz (space)!”#$%&’()*+,-./:;<=>?@[\]^_`{|}~

< To use a wired Internet connection, select “[Wired]”.

1 2

5 6 7

Last listened Station list

Location Genre

Listening to Internet Radio

My Favourites Stations

Listening to an Internet Radio station/a Podcast

Select Internet Radio by pressing the SOURCE button

repeatedly.

< You can also use the BAND button on the remote control unit.

Select “Stations” for Internet Radio stations, or “Podcasts”

for Podcasts.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

A list of search methods appears.

Select a search method.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

< When you use the Internet Radio function for the first time, the

unit starts an initial setup procedure. (page 19)

Open the Internet Radio menu.

Press the MENU button.

The Internet Radio menu appears.

< See page 22 for the details of the Internet Radio menu.

Select “Station list”.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

Location:

Search by the location of the broadcaster.

Genre:

Search by the genre of music played on the station/Podcast.

Search stations:

Search by the station’s name.

Search podcasts:

Search by the Podcast’s name.

Popular stations:

Select from a list of popular stations.

New stations:

Select from a list of recently added stations.

ENGLISH

Business News Celtic

Celtic Songs & D Buffering

Celtic Songs & D Opening...

Celtic Songs & D Playing

If you have selected “Location”, “Genre” or “Search

stations” in step

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

, search for the channel you want.

To change the displayed information

< For the operations of inputting characters, see “How to input

characters” on page 19.

A list of stations/Podcasts is displayed.

Select a station or a Podcast you want to listen to.

Turn the MULTI JOG/ENTER knob to select an item, and press the knob.

Each time the INFO button is pressed, information on the second line of the display changes.

Internet radio:

Playing

Signal strength

(for wireless LAN)

Format

Reliability

Description

Genre

Location

< The types of information displayed may vary depending on the

stations/Podcasts.

Podcast:

Playing

Signal strength

(for wireless LAN)

URL

Description

Language

City

State

Country

Bookmark

Now you can listen to the station.

To store the current station/Podcast as favourite

Press and hold the MEMORY button until “Favourite Added” is displayed.

Your favourite stations can be easily accessed from “My favourites” in “Station list”.

< You can also use the ENTER button on the remote control unit. < You can also add to your favourite stations using the Internet

radio portal. (page 24)

Last listened Station list

Internet Radio Menu Operations

You can access channel lists or setup menus using the Internet Radio menu of this unit.

To open the Internet Radio menu

While listening to the Internet Radio, press the MENU button to open the Internet Radio menu.

< Press the MENU button again to return to the playback display.

To scroll through the menu items

Turn the MULTI JOG/ENTER knob.

Items of the Internet Radio menu

Last listened

You can select the station/Podcast from the ones you listened to recently.

Station list

My favourites

List of stations/Podcast you stored as favourite is displayed. Select a station/Podcast you want to listen to. (page 21)

Stations

List of Internet Radio stations is displayed. (page 20)

Podcasts

List of Podcasts is displayed. (page 20)

My Added Stations

List of stations/Podcasts you personally added on the radio potal is displayed. Select a station/Podcast you want to listen to. (page 24)

Help

Get access code

The “access code” of the unit is displayed. (page 24)

FAQ

Audio FAQ is available.

< You can also use the scroll buttons (.°//‡) on the

remote control unit to scroll through menu items.

To select a menu item

Press the MULTI JOG/ENTER knob.

To go back to the previous screen

Press the search button (m) on the remote control unit.

Setup

System setup

Software and Internet settings are available. (page 23)

Info

Software version and the Radio ID of the unit can be displayed. (page 23)

< The Radio ID may be required when you contact our customer

support.

ENGLISH

Network Configuration

Internet setup Software update

Last listened Station list

Press ‘Info’ to X.X.X.XXX

Update finish Select to reboot

Software update

The software of the unit can be updated via the Internet connection, so that you are able to use the latest features of the unit. Regularly check for updates.

< You need the remote control unit for update operations. < You can check the current software version of your unit using the

Internet radio menu. Follow the menu items as follows:

Setup w Info w SW version

< Do not turn off the unit during updating process.

Se lec t Inter net Rad io by p ressing the BAND button

repeatedly.

< You can also use the SOURCE button on the main unit.

When an update is available, “Press ‘Info’ to update to

X. X.X. XXX” appears. Press INFO/RDS button to start update.

< You can also use the INFO button on the main unit. < When no update is required, “Software up to date” appears. Press

the MENU button to finish the operation.

When the update is completed, “Update finish Select

to reboot” appears. Press ENTER button to reboot the software.

Open the Internet radio menu.

Press the MENU button.

Select “Setup”, “System setup”, and then “Software

u pd a te ”.

Press the scroll buttons (.°//‡) to scroll to the menu item you want, and then press the ENTER button.

Performing the setup wizard

If you have moved or modified your network environment, or if you have a problem connecting to the Internet, perform the initial setup wizard to establish the Internet connection again. Follow the menu items as follows:

Setup w System setup w Internet setup w Wizard

Setting the wireless network

If you are using a wireless network for the unit and you have moved to a new location, change the area setting so that network connection is established properly. Follow the menu items as follows:

Setup w System setup w Internet setup w Wlan region

< On the main unit, turn the MULTI JOG/ENTER knob to scroll to the

menu item you want, and then press the MULTI JOG/ENTER knob.

Manual Internet setup

You can check and modif y detailed settings of the Internet connection. Follow the menu items as follows:

To check the current network settings

Setup w System setup w Internet setup w View settings

To configure settings

Setup w System setup w Internet setup w Manual settings

To delete a network profile

Setup w System setup w Internet setup w Network profile

Radio Portal

Access code SGPD7DM

Setting up Music Player (1)

Internet Radio portal

Access the radio portal on the Internet using your computer to fully enjoy the Internet Radio function of this unit.

< You can create a list of your favourite stations/Podcasts on the

portal. This list can be viewed from your unit, making it easier for you to find your usual programmes. You can see the list of your favourite stations in the Internet Radio menu as follows:

Station list w My favourites

< If the station/Podcast you want to listen to is not in the channel

list, you can create your own list. You can see the list of your added stations in the Internet Radio menu as follows:

Station list w My Added Stations

Accessing the Radio portal

1. Open your internet browser and access http://www. wifiradio-frontier.com.

2. Click on the “Register” link to start registration.

3. Input your access code and log in.

About the Music Player function

Using the Music Player function, you can play back the music files in your computers on the same LAN. There are two ways of connecting to the computer: using Shared Media and using Shared Folders.

Shared Media

Using the Shared Media function, AG-H600NT can play back the music files in the shared media library on your computer. Tag items such as artist names and album names can be viewed from AG-H600NT as well. You need a PC running on Windows XP or Windows Vista, and Windows Media Player 11 or later on it.

Shared Folders

Once you set the files on your computer open to access, AG-H600NT can connect to the computer and play back the files. To use this function, you need to configure the sharing settings of your music folders so that other computers or AG-H600NT can read the files. This function is available both on Windows and on Macintosh.

Checking the “access code” of your unit

Each unit of AG-H600 series receiver has its “access code”. This code is required to log in the Internet Radio portal.

Select Internet Radio by pressing the SOURCE button

repeatedly.

< You can also use the BAND button on the remote control unit.

Open the Internet Radio menu.

Press the MENU button.

Select “Station list”, “Help”, and then “Get access code”.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob. Repeat this operation until the menu you want appears.

The access code of your unit is displayed.

Preparations for Shared Media

Connect your computer to the LAN.

Connect the AG-H600NT to the LAN. (page 8)

< If you have a problem connecting to the LAN, see page 23.

If the files you want to share are not yet added to the

media library of Windows Media Player, add them to the media library.

< Refer to the manual of Windows Media Player for details.

On Windows Media Player, open “Library”, then “Media

sharing”.

Click on “Settings...”, and configure detailed sharing

settings.

< To listen to music files regardless of their rating, set “Star ratings”

to “All ratings”.

< Ensure that “Music” is checked under the “Media types” setting.

For the procedure of playback, see “Listening to Music Player (Shared Media)”. (page 29)

ENGLISH

Media Sharing window opens.

Activate “Share my media to:”.

The AG-H600NT appears in the device list as “Unknown Device”.

Select the “Unknown Device” and click “Allow”.

The AG-H600NT can now access to the shared library.

Setting up Music Player (2)

Preparations for Shared Folders (Windows XP)

Check the name of the Domain or the “Workgroup” your

computer belongs to.

To enable Shared Folders, your computer needs to be a member of a Domain or a “Workgroup”. Usually, your computer belongs to a “Workgroup” by default. To see the name of the Domain or the “Workgroup” your computer belongs to, check the PC setting as follows:

Control Panel w System w Computer Name

Check the user account name and its password.

To access the computer from AG-H600NT, you need the user account name and the password of the computer.

Right-click on the folder which contains the music files

you want to share, and select “Sharing and Security”.

Preparations for Shared Folders (Windows Vista)

Check the name of the Domain or the “Workgroup” your

computer belongs to.

Control Panel w System and Maintenance w System

Check the user account name and its password.

To access the computer from AG-H600NT, you need the user account name and the password of the computer.

Open “Control Panel”, “N etwork and Inte rnet”, th en

“Network and Sharing Center”.

Set “Public folder sharing” to “On (read only)”.

In the “Sharing” tab, check “Share this folder”.

Set “Password protected sharing” to “On”.

Copy the music files you want to enjoy on AG-H600NT into

the “Public Music” folder in the “Public” folder.

ENGLISH

Preparations for Shared Folders (Mac OSX 10.2.1 to 10.4.11)

Preparations for Shared Folders (Mac OSX 10.5.0 or higher)

Check the user account name and its password.

To access the computer from AG-H600NT, you need the user account name and the password of the computer.

In “System Preferences”, open “Sharing”.

Activate “Personal File Sharing” and “Windows Sharing”.

Open “Directory ac cess” in the “Utitlities ” fold er in

“Applications”, and check that the following items are enabled in the “Services” tab.

< App leTa lk < LDAPv3 < SLP < SMB/CIFS

Check the user account name and its password.

To access the computer from AG-H600NT, you need the user account name and the password of the computer.

In “System Preferences”, open “Sharing”.

Enable “File Sharing”, and then select “Read Only” for

“Everyone” in “Users” window. Then Click “Options...”.

Activate “Share files and folders using AFP” and “Share

files and folders using SMB”. In the same window, activate “On” for the account you want to use for file sharing.

Select “SMB/CIFS”, and click on “Configure...”, and select

an appropriate workgroup.

Preparation on the unit for Shared Folders (both Windows and Macintosh)

Connect your AG-H600NT to the LAN. (page 8)

< If you have a problem connecting to the LAN, see page 23.

Enter the user name and the password required to access

the computer.

Enter the user name and the password following the menu as follows:

Setup w System setup w Internet setup w PC Setup w User Name / Password

For the procedure of playback, see “Listening to Music Player (Shared Folders)”. (page 30)

3 4

Shared media Shared folders

Most of Europe USA

005AD904JM2 [Wired]

Music Player Initial Setup

Initial setup

When you use the Music player function for the first time, the unit starts an initial setup procedure to connect to the LAN.

Select M usic Player by pressing the SOURCE button

repeatedly.

Select a network name you want to use.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

< To use a wired Internet connection, select “[Wired]”.

Enter the correct password for the network if required.

< See “How to input characters” page19.

< You can also use the BAND button on the remote control unit.

Select “Shared media” or “Shared folders”.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

Select your country/area.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

< If you have a problem connecting to the LAN, see page 23.

Now the unit starts to connect to the LAN. When connection is established successfully, the Music Player menu is displayed.

ENGLISH

Shared media Shared folders

Music Video

Listening to Music Player (Shared Media)

Music 1 Music 2

HOME-PC: JOHN:

For the preparations of Shared Media, see page 25.

Select M usic Player by pressing the SOURCE button

repeatedly.

The Music Player menu appears.

< You can also use the BAND button on the remote control unit.

< When you use the Music player function for the first time, the

unit starts an initial setup procedure. (page 28)

Select “Shared media”.

Turn the MULTI JOG/ENTER knob to select “Shared media”, and then press the MULTI JOG/ENTER knob.

Select the folders until the file you want to listen to

appears.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob. Repeat this operation until the file you want appears.

< You can also search for files by selecting “<Search>”.

Select the file you want to listen to.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

A list of computer name appears.

Select your computer name and user account name.

Turn the MULTI JOG/ENTER knob to select the item, and then press the MULTI JOG/ENTER knob.

User account nameComputer name

Playback of the selected file starts.

If you have a problem connecting to the shared media

< Check if “Allow” is selected for AG-H600NT (“Unknown Device”)

(page 25).

< Check if your AG-H600NT is properly connected to the LAN.

+ 67 hidden pages

TEAC AG-H600NT Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

IMPORTANT SAFETY INSTRUCTIONS

Contents

Before Use

Connecting Antennas (AM/FM)

Connection

System ConnectionInternet Connection

Remote Control UnitSpeaker Connection

Parts Identification

Basic Operation

Adjusting Bass, Midrange, Treble, and Balance of Speakers

Listening to iPod

Listening to FM/AM

Internet Radio Initial Setup

Internet Radio Menu Operations

Radio Portal