Teac AD-850 Owners Manual

D01308150A

AD-850

ENGLISH

Cassette Deck/CD Player

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

FRANÇAIS

ESPAÑOL

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from earphones or headphones can cause hearing loss.

For U.S.A.

CAUTION

Laser information

o Do not expose this apparatus to drips or splashes. o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a book

case or similar unit.

o The apparatus should be located close enough to the AC outlet

so that you can easily reach the power cord plug at any time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine, fire or excessive heat.

o CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an incorrect type of battery. Replace only with the same or equivalent type.

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to fire, injury or the staining of nearby things. Please read and observe the following precautions carefully.

This product contains a semiconductor laser system inside the cabinet and is classified as a “CLASS 1 LASER PRODUCT”. To prevent being exposed to the laser beam, do not try to open the enclosure.

Laser:

Type: EP-C101 Manufacturer: GUANGDONG EVER BRIGHT GROUP CO.,LTD Laser output: Less than 1 mW on the objective lens Wavelength: 790 ±25 nm

Model for USA

This product has been designed and manufactured according to FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the Radiation Control for Health and Safety Act of 1968”, and is classified as class ! laser product. There is not hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings.

The label required in this regulation is as follows:

ENGLISH

o Be sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

o Use batteries of the same type. Never use different types of batter-

ies together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery com-

partment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

Pb, Hg, Cd

IMPORTANT SAFETY INSTRUCTIONS (continued)

Model for USA

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Model for Canada

Industry Canada’s Compliance Statement: This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

This product complies with the European Directives request, and the other Commission Regulations.

For European Customers

Disposal of electrical and electronic equipment and batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal waste stream via collection facilities designated by the government or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the environment and human health because of the presence of hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been crossed out, indicate that electrical/electronic equipment and batteries/accumulators must be collected and disposed of separately from household waste. If a battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) as defined in the Battery Directive (2006/66/ EC), then the chemical symbols for those elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electrical/electronic equipment and waste batteries/accumulators, please contact your city office, waste disposal service or the shop where you purchased the equipment.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Supply of this product does not convey a license nor imply any right to distribute MPEG Layer-3 compliant content created with this product in revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), streaming applications (via Internet, intranets and/or other networks), other content distribution systems (pay-audio or audio-on-demand applications and the like) or on physical media (compact discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for such use is required. For details, please visit http://mp3licensing.com.

MPEG Layer-3 audio coding technology is licensed from Fraunhofer IIS and Thomson.

Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.

Thank you for choosing this TEAC product. Read this manual

LINE IN

carefully to get the best performance from this unit.

IMPORTANT SAFETY INSTRUCTIONS ..............................2

What you can do with this unit ...................................5

Before use ........................................................6

Discs .............................................................7

Cassette tapes ....................................................8

USB flash drives ..................................................9

MP3 files ....................................................... 10

Identifying the parts (remote control) ...........................10

Identifying the parts (main unit) .................................12

Using the remote control ........................................14

Display ..........................................................14

Connections ....................................................16

Basic operation ..................................................17

Listening to a CD ................................................18

Repeat playback ................................................ 20

Shuffle playback ................................................ 20

Programmed playback ......................................... 21

Listening to a cassette tape ..................................... 24

Listening to files on a USB flash drive ........................... 26

Recording on a USB flash drive .................................28

Erasing files from a USB flash drive .............................. 30

Recording on a cassette tape ....................................31

Mic mixing with playback and recording ........................34

Timer-controlled playback and recording .......................36

Automatic power saving function ..............................38

Troubleshooting ................................................ 39

MP3 playback order ............................................40

Maintenance ...................................................40

Specifications ...................................................41

What you can do with this unitContents

Playback

Recording

CD/CD-R/CD-RW (Audio CD/MP3 disc)

e “Listening to a CD” on page 18

Cassette tape

e “Listening to a cassette tape” on

page 24

MP3 files on a USB flash drive

e “Listening to files on a USB flash

drive” on page 26

Record on a USB flash drive from a CD, a cassette tape or an external source

e “Recording on a USB flash drive” on

page 28

Record on a cassette tape from a CD, a USB flash drive or an external source

e “Recording on a cassette tape” on

page 31

ENGLISH

Timer operation

Requires a commercially-available timer

e “Timer-controlled playback and recording” on page 36

Timer-controlled playback

Timer-controlled recording

Before use

What’s in the box

Confirm that the standard accessories are included.

Remote control (RC-1329) × 1

Batteries (AAA) for remote control × 2

RCA audio cables × 2

Owner’s manual (this document) × 1

o For information about the warranty, users living in the USA

and Canada should see pages 124–125 and the back cover (warranty document). Users living in Europe and other regions should see page 126.

o Keep this manual in a safe place for future reference.

Placement of the unit

< Choose the location where you install the unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. You should also avoid locations that are subject to vibrations or exposed to excessive dust, heat, cold or moisture.

< As the unit may become warm during operation, always leave

sufficient space around it for ventilation.

< Do not place the unit on an amplifier, a receiver or any other

device that generates heat.

Beware of condensation

When the unit is moved from a cold to a warm place, or used after a sudden temperature change, there is a danger of condensation; vapor in the air could condense on the internal mechanism, making correct operation impossible. To prevent this, or if this occurs, leave the unit turned on for one or two hours. Then the unit will stabilize at the temperature of its surroundings.

Using the TEAC Global Site

Quick start guide for recording × 1

Precautions for use

< Do not move the unit during CD playback.

During CD playback, the disc rotates at high speed. Do not lift or move the unit during playback. Doing so might damage the disc or the unit.

< The voltage supplied to the unit should match the voltage that

is printed on the rear panel. If you are in any doubt regarding this matter, consult an electrician.

< Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into the unit, contact your dealer or service company.

< When removing the power plug from the wall outlet, always pull

directly on the plug, never yank on the cord.

< Always remove the disc before relocating or moving this unit.

Moving the unit with a disc inside it could cause malfunction.

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

1) Open the TEAC Global Site.

2) In the TEAC Downloads section, click the desired language to open the Downloads website page for that language.

NOTE

If the desired language does not appear, click Other Languages.

3) Click the “Search by Model Name” section to open the Downloads page for that product. (Users in Europe should click the product name in the “Products” section instead.)

4) Select and download the updates that are needed.

Product registration

Customers in the USA, please visit the following TEAC website to register your TEAC product online.

http://audio.teac.com/support/registration/

Discs

Discs that can be played by this unit

CDs (12-cm and 8-cm) that bear the “COMPACT disc DIGITAL AUDIO” logo can be played by this unit.

< The logo should be on the disc label or the CD jacket.

CD-R and CD-RW discs that have been correctly recorded in the audio CD format and finalized, as well as finalized CD-R and CD-RW discs that contain MP3 files, can be played by this unit.

This unit can play these types of discs without an adapter. It cannot play any other type of disc.

Playback of any other type of disc could cause loud noise and

damage to speakers as well as harm hearing. Never try to play any other type of disc.

< Depending on the quality of the disc and/or the condition of the

recording, some discs might not be playable.

< Video CDs, CD-ROMs and similar types of discs can be read by the

unit, but they will make no sound when played back.

Precautions for use

< Do not play any disc that is warped, deformed or damaged.

Playing such discs could cause irreparable harm to the playing mechanisms.

< Printable CD-R and CD-RW discs are not recommended because

their label sides could be sticky and damage the unit.

< Do not stick paper or protective sheets on discs and do not use

any protective coating sprays.

< Never use a stabilizer. Using commercially-available CD stabilizers

with this unit will damage the mechanisms and cause them to malfunction.

< Do not use irregularly-shaped discs (octagonal, heart-shaped,

business card size, etc.). Such CDs could damage the unit.

Handling precautions

ENGLISH

< Super Audio CDs cannot be read or played back by this unit.

< Video and audio DVDs, DVD-ROMs and other types of DVDs

cannot be read or played back by this unit.

ATTENTION

If you put a video or audio DVD, DVD-ROM or other type of DVD into the disc tray, the unit will attempt to read the disc and rotate at high speed. If you accidentally insert such a disc, wait until the unit stops spinning before ejecting it in order to avoid possibly damaging the disc. Do not attempt to remove the disc when “READING” appears on the display.

< Copy-protected discs and other discs that do not conform to the

CD standard might not play correctly in this player. If you use such discs in this unit, TEAC Corporation and its subsidiaries will not be responsible for any consequences or guarantee the quality of reproduction. If you experience problems with such non-standard discs, you should contact their issuers.

About CD-R/CD-RW discs

This unit can play back CD-R and CD-RW discs that have been recorded in the audio CD format (CD-DA) and the MP3 format.

< Discs created by a CD recorder must be finalized before use with

this unit.

< Depending on disc quality and recording conditions, playback of

some discs might not be possible. Please see the manual for the device that you used to create the disc.

< Always place the disc on the disc tray with the label side up. Only

one side of a Compact Disc can be played or used for recording.

< To remove a disc from a standard storage case, press down on the

case through the center of the disc and lift the disc out, holding it carefully by its edges.

How to remove a disc How to hold a disc

Storage precautions

< Discs should be returned to their cases after use to avoid dust and

scratches that could cause the laser pickup to “skip.”

< Do not expose discs to direct sunlight or high temperature

or humidity for extended periods. Long exposure to high temperatures will warp discs.

< CD-R and CD-RW discs are more sensitive to the effects of heat

and ultraviolet rays than ordinary CDs. It is important that they not be stored in locations where they will be exposed to direct sunlight. They should also be kept away from sources of heat, such as radiators and heat-generating electrical devices.

< If you are uncertain about the handling of a CD-R or CD-RW disc,

please contact the seller of the disc directly.

Discs (continued)

Cassette tapes

Maintenance

< If a disc becomes dirty, wipe its surface radially from the center

hole outward towards the outer edge with a soft, dry cloth.

< Never clean discs using chemicals such as record sprays, antistatic

sprays and fluids and thinners. Such chemicals will do irreparable damage to the disc’s plastic surface.

If you are in any doubt as to the care and handling of a CD-R or CD-RW disc, read the precautions supplied with the disc or contact the disc manufacturer.

Tape types

There are several types of cassette tapes.

Cassette tapes that can be played by this unit

Normal (type ) Chrome (type ) Metal (type )

Cassette tapes that can be recorded on by this unit

Normal (type ) Chrome (type )

ATTENTION

< Do not open a cassette or pull out the tape. < Do not touch the tape.

Storage precautions

< Keep cassette tapes away from magnets or magnetized items

because they may cause noise or erase recorded contents.

< Do not leave cassette tapes in a dusty place.

< Do not store cassette tapes in a place with high temperature or

humidity.

Types of cassette tapes that should be avoided

The following types of cassette tapes might prevent the unit from operating or functioning normally. The tape of such cassette tapes could be caught in the unit and cause unexpected problems.

Deformed cassette tapes

Cassettes that are deformed, that have tape that does not track properly, or that generate abnormal noise during fast-forwarding or rewinding.

Long-duration tapes

Tapes that allow recording for longer than 90 minutes sometimes get caught by the capstan because they are extremely thin and stretch easily. Do not use them.

Slackening of tapes

Slack tape could get caught in the capstan or other parts. Eliminate slack by using a pencil or similar tool before use.

USB flash drives

Normal

Automatic tape type

detection holes

Accidental erasure prevention tab

Automatic tape type detection function

This cassette deck can detect what type of tape is being used based on the detection holes in the cassette shell. Be sure to use cassettes with detection holes.

Metal (Type

Chrome (Type

(

Type

)

Accidental erasure prevention tabs

Tabs in the top of the cassette shell allow you to prevent important recordings from being erased by mistake. There are two tabs in each cassette shell—one for “side A” and one for “side B.”

Once these tabs have been removed using a screwdriver or similar tool, there is no chance of the recording function being activated by accident.

ATTENTION

Never turn the unit off or disconnect a USB flash drive when it is being accessed, for example, during writing, playback, recording or the erasure of files. Doing so could damage the unit and the connected USB flash drive.

Compatibility

o Only USB flash drive can be used. o Hard disk drives, CD/DVD drives, and other devices connected via

USB cannot be used. o This unit cannot copy or move files. o Playable formats: FAT12, FAT16, FAT32 o NTFS, HFS and HFS+ formats cannot be used. o Max. number of playable folders: 255 o Max. number of playable/recordable files: 999 o Operation with all USB flash drives is not guaranteed. o When recording from a CD to a USB flash drive, the monitored

sound might skip depending on the type of USB flash drive, but

this will not affect the recorded data.

ENGLISH

for “side A”

“side A”

o To record on a cassette that has had its tab broken off, put a piece

of adhesive tape over the hole. Be careful not to block the tape type detection holes.

Recording

This unit can record sound from CDs, cassette tapes and connected external devices, including tuners, to USB flash drives in MP3 format. See page 28 for details.

MP3 files

This unit can play MP3 files that are on CD-R/CD-RW discs and external USB flash drives.

o Playable audio file formats

MP3 (with “.mp3” extension)

8–320kbps bit rate 16–48kHz sampling frequency

NOTE

DRM (Digital Rights Management) is not supported.

o Up to eight levels of subfolders are supported.

File information display

Identifying the parts (remote control)

The display of this unit can only show single-byte letters and numbers.

< If the file information uses Japanese, Chinese or other double-byte

characters, playback is possible but the name will not be shown correctly. In such cases, “

Precautions when preparing MP3 files using a computer or other device

o Discs that have not been recorded in accordance with ISO 9660

specifications cannot be played back.

o MP3 files are recognized by the “.mp3” extension. Always include an

extension at the end of the file name.

o Files without extensions cannot be recognized. Files that are not in

the MP3 data format cannot be played back even if they have an extension.

o After writing to a CD-R/CD-RW, close the session (complete disc

creation). If the session has not been closed, the disc cannot be played back.

o This unit can play a maximum of 999 files in a maximum of 255

folders. If data exceed these numbers, proper playback might not be possible for files numbered 1000 or higher and files in folders numbered 256 or higher.

o Discs recorded using multiple sessions are not supported. Only the

first session will be played back.

o Depending on the disc condition, this unit might not be able to

play some discs or skipping could occur.

o Files protected by DRM cannot be played back by this unit.

” is displayed.

A B

E F

If both the main unit and the remote control have buttons with the same function, we only explain procedures using one of them in this manual. However, the other can also be used in the same manner.

SOURCE button

Use this button to select a source (page 17).

DISPLAY button

Press this button to change the display information (page 15).

REPEAT button

Use this button to set the repeat function (page 20).

SHUFFLE button

Use this button to start shuffle playback (page 20).

PROGRAM button

Use this button to program tracks/files (page 21).

CLEAR button

Use this button to clear programmed tracks/files (page 23).

RECORD (>) button

Use this to record to an external USB flash drive. Press it once to enable recording standby, and press it again to start recording. (page 28) Press it during recording to divide the file at that point (page

30).

Stop (H) button

This stops USB flash drive recording/playback.

Play (t) button

Press this button to start playback. When in USB recording standby, press this to start recording.

Pause (J) button

Press this button to pause playback or recording. Press this button again to resume playback or recording.

Stop (H) button

Press this button to stop playback. Press this button to stop recording to a tape.

ENGLISH

FOLDER ( / ) buttons

Use these buttons to select MP3 folders (pages19 and 27).

Skip (.//)/Search (m/,) buttons

Press these buttons to skip through tracks/files. Hold down these buttons to search for part of a track/file.

OPEN/CLOSE (L) button

Press this button to open and close the disc tray.

Stop (H) button

Press this button to stop playback.

Play (t) button

Press this button to start playback.

Pause (J) button

Press this button to pause playback. To resume playback, press this button again.

ERASE button

Use this button to erase files from a USB flash drive (page 30).

Play (t) button

This starts cassette tape playback. Press when a cassette tape is paused to resume playback/ recording.

Pause (J) button

Press this button to pause playback or recording. Press this button again to resume playback or recording.

ATTENTION

When stopped, pressing the Pause (9) button will not put the tape into a paused state.

Fast-forward/Rewind (m/,) buttons

Press these buttons to fast-forward/rewind the tape.

RECORD (>) button

Use to record to a tape. Press it once to enable recording standby, and press it again to start recording (page 31).

COUNTER RESET button

Press this button to reset the tape counter to “0000”.

REC LEVEL ( − / + ) but tons

Use these buttons to adjust the recording level.

Skip (.//)/Search (m/,) buttons

Press these buttons to skip through files. Hold down these buttons to search for a part of a file.

Identifying the parts (main unit)

2831 30 29 27 25 23 2132 26 22 20

43 5

6 7

1110

132

1819

Display

This shows the total number of tracks/files, playback time and other information (page 14).

Remote sensor

When operating the remote control, point it towards here.

OPEN/CLOSE (L) button

Press this button to open and close the disc tray.

COUNTER RESET button

Press this button to reset the tape counter to “0000”.

REC LEVEL knob

Turn this knob to adjust the recording level.

Skip (.//)/Search (m/,) buttons

Press these buttons to skip through tracks/files. Hold down these buttons to search for part of a track/file.

REPEAT button

Use this button to set the repeat function (page 20).

SOURCE button

Use this button to select the source (page 17).

RECORD USB button

Use to record to an external USB flash drive. Press it once to enable recording standby, and press it again to start recording (page 28). Press it during recording to divide the file at that point (page

30).

RECORD TAPE button

Use to record to a tape. Press it once to enable recording standby, and press it again to start recording (page 31).

Fast-forward/Rewind (m/,) buttons

Press these buttons to fast-forward/rewind the cassette tape.

Pause (J ) button

Press this button to pause cassette tape playback or recording. Press this button again to resume playback or recording.

Cassette tape compartment

MIC connector and mic LEVEL knob

When using a mic to record, insert the mic cable plug into this connector and turn the knob to a suitable level (page 34).

This unit does not support stereo mics. Use a mono dynamic mic. Set the MIC LEVEL knob to MIN when not using a mic.

Stop (H ) button

Press this button to stop cassette tape playback. Press this button to stop recording to a tape.

Play (t) button

Press this button to start CD playback.

Stop (H ) button

Press this button to stop CD playback.

Skip (.//)/Search (m/,) buttons

Press these buttons to skip through files. Hold down these buttons to search for part of a file.

POWER ON START CD-TAPE-USB switch

Use this switch to set the sound source that is active when the power is turned on. Use this switch to set the media used for timer playback/ recording. (The timer recording can only record to cassette tape.) To use timer playback/recording, connect a commerciallyavailable programmable timer to this unit (page 36).

Pause (J ) button

Press this button to pause USB playback or recording. Press this button again to resume playback or recording.

Play (t) button

Press this button to start USB playback. When in USB recording standby, press this to start recording.

ENGLISH

EJECT (L) button

When the tape is stopped, press this button to open the cassette tape compartment.

Play (

This starts cassette tape playback. Press when a cassette tape is paused to resume playback/ recording.

Turn this knob to vary the playback speed (page 25).

This changes the echo mode (page 35).

) button

PITCH CONTROL knob

ECHO MODE switch

Pause (J) button

Press this button to pause CD playback. To resume playback, press this button again.

FOLDER ( / ) buttons

Use these buttons to select folders (pages19 and 27).

Stop (H ) button

Press this button to stop USB playback. Press this button also to stop recording to USB.

Disc tray

USB port

Connect an external USB flash drive here.

POWER button

Press this button to turn the unit on or off.

ATTENTION

POWER ON START OFF-PLAY-REC (TAPE) switch

Use this switch to set the timer operation mode (off, play or record). To use this when set to play or record, connect a commerciallyavailable programmable timer to this unit (page 36).

o Select OFF to not use timer playback or recording.

Currently playing track number

Elapsed time of current track (min./sec.)

Elapsed time of current track

Currently playing file number

(scrolls when long)

Total tracks

Total playing time

Total number of folders

Total number of files

Using the remote control

Display

Precautions when using the remote control

CAUTION

Misuse of batteries could cause them to rupture or leak, which might result in fire, injury or the staining of nearby materials. Please read and observe the precautions on page 3 carefully.

o When using the remote control, point it toward the remote control

signal receiver on the main unit from a distance of 5 m (16 ft) or less. Do not place obstructions between the main unit and the remote control.

< Even if the remote control is used within its effective range,

operation by remote control might not be possible if there are any obstacles between the unit and the remote control.

< If the remote control is operated near other devices that generate

infrared rays, or if other remote controls that use infrared rays are operated near the unit, this unit and the other devices might not operate correctly.

Battery installation

CD mode

During playback

Audio CD

MP3 disc

(starting with 001 in each folder)

Currently playing folder number

(min./sec.)

1. Remove the battery compartment cover.

2. Insert two AAA batteries. Make sure that they are inserted with

their positive (+) and negative (_) poles oriented correctly.

3. Close the cover.

Battery replacement

If the distance from the main unit that the remote control works effectively decreases, the batteries are probably exhausted. Replace the batteries with new ones when this happens. For more information about the collection of batteries, please contact your local municipality, your waste disposal service or the place where you purchased them.

Currently playing file name

When playback is stopped

Audio CD

MP3 disc

TAPE mode

Tape counter

Elapsed time of current file

Currently playing file number

(scrolls when long)

Total number of folders

Total number of files

Recording source Recording indicator

Remaining time of current track (min./sec.)

Total elapsed time of the disc (min./sec.)

Total remaining time of the disc (min./sec.)

Currently playing track number and elapsed time of current track (min./sec.)

File name

o The tape counter shows the approximate position of the tape. This

is not a time indication.

USB mode

Changing the display (CD/USB mode)

During playback in CD mode or USB mode, each time the DISPLAY

button is pressed, the display changes as follows:

During playback

(starting with 001 in each folder)

Currently playing folder number

Currently playing file name

When playback is stopped

(min./sec.)

Audio CD

ENGLISH

MP3 disc/USB

Title

Artist

Album

Currently playing folder and file number, elapsed time of current track (min./sec.), and currently playing file name

Recording mode

(Example: Recording on a cassette tape from a USB flash drive)

Current file number

current file (min./sec.)

< “No title”, “No album” or “No artist” appears when there is no

information.

< “

< The display of this unit can only show single-byte letters and

numbers. If a file name uses Japanese, Chinese or other doublebyte characters, playback is possible but the name will not be shown correctly. In such cases, “

Tape counterElapsed time of

” appears when the unit cannot read the information.

” is displayed.

Connections

Complete all other connections before turning the unit

on.

o Read the instructions of each device that you intend to use with

this unit.

o Be sure to connect each plug securely. Do not bundle connecting

cables with power cords. Doing so could cause noise.

AD-850 (back side)

LINE IN/OUT connectors

These connectors transmit an analog 2-channel audio signal. Connect the components using the included RCA audio cables. Connect a stereo amplifier, mixer or other equipment to this unit’s analog audio input and output connectors.

Use the included RCA audio cables (or commercially-available ones) for connections.

Connect this unit’s R input connector to the R output connector of the audio output device, and this unit’s L input connector to the L output connector of the other device.

LINE OUT

RCA audio cables

LINE

Tuner, etc.

Amplifier

Speakers

Wall socket

White (L) Red (R)

This unit Amplifier, etc.

AC Power Cord

After all other connections are complete, connect the plug to an AC wall outlet.

Be sure to connect the power cord to an AC outlet that

supplies the correct voltage.

Hold the power plug when plugging it into an outlet or

unplugging it. Never pull or yank on the power cord.

White (L)

Red (R)

Example

Notes on turning on or off the power

When an amplifier is connected to the unit, turn on or off the power of the unit and the amplifier in the following sequence.

When turning on the power

1. This unit

2. Amplifier

When turning off the power

1. Amplifier

2. This unit

Basic operation

Turning the unit on or off

Press the POWER button to turn the unit on or off. When the unit turns on, the display lights.

Check the POWER ON START switches that determine what the unit does when the power is turned on.

When the power is turned on, and the POWER ON START OFF-PLAY-REC (TAPE) switch for the timer is set to PLAY or REC

Selecting a source for playback/recording

Each time the SOURCE button is pressed, the source changes as

follows:

ENGLISH

The selected source is shown on upper left of the display.

< During recording, the source cannot be changed.

< Pressing the play button for a source also selects and starts

playback of that source.

The source set with the POWER ON START CD-TAPE-USB switch starts playback/recording.

The timer recording can only record to cassette tape (page

37).

When the power is turned on, and the POWER ON START OFF-PLAY-REC (TAPE) switch for the timer is set to OFF

The source set with the POWER ON START CD-TAPE-USB switch becomes the active source.

< When you do not want to use the timer, be sure to set the

POWER ON START OFF-PLAY-REC (TAPE) switch to the OFF position to prevent accidentally recording over an important cassette tape.

< Select “LINE” to use an external source connected to the LINE

connectors.

Listening to a CD

Press the SOURCE button repeatedly to select “CD”.

< When a different source is selected, pressing the CD Play (t)

button automatically selects the CD and, if a disc is loaded, starts playback.

Press the CD OPEN/CLOSE (L) button to open the disc

tray.

Press the CD OPEN/CLOSE (L) button again to close the

tray.

CAUTION

Be careful not to let your finger be pinched by the tray.

Loading a disc takes a few seconds. During loading, “READING” appears on the display and no buttons will work. Wait until the total number of tracks/files is displayed.

< When no disc is loaded, “NO DISC” is displayed.

Press the CD Play (t) button to start playback.

Place a disc on the tray with the label side up.

< Always confirm that the disc is centered on the tray. The disc

must be centred on the disc tray. If a disc is not correctly loaded, it might not be possible to open the tray again after it has been closed.

ATTENTION

< Do not load more than one disc. < Do not force the tray by hand when opening and closing it. < Do not attach adhesive labels or similar materials to either side

of a disc.

< Do not use irregularly-shaped discs. Failure to follow any of the above could cause malfunction.

Playback starts from the first track/file on the disc.

< If you load a disc, and then press the CD Play (t) button

without having first closed the disc tray, the disc tray closes and playback starts.

< When playback of all the tracks/files has finished, the unit stops

automatically.

< MP3 files that are not placed in folders are automatically put in

the “ROOT” folder. Playback starts from the first file in the ROOT folder.

< See page 40 for information about the playback order of MP3

discs.

Suspending playback temporarily (Pause mode)

Search for a part of a track/file

Press and hold

Press the CD Pause (J) button during playback to stop playback at the current position. To resume playback, press the CD Pause (J) button again or press the CD Play (t) button.

Stopping playback

Press the CD Stop (H) button to stop playback.

Opening the disc tray

During playback, hold down a CD Search (m or ,) button to

search a part of a track/file. Release it when you find the beginning

of the part you want to hear.

ENGLISH

Skipping to an earlier or later track/file

During playback

Press a CD Skip (.//) button repeatedly until the desired

track/file is selected. The selected track/file will be played from the

beginning.

o If the . button is pressed once during playback, the track/

file being played will be played again from its beginning. To return to the beginning of the previous track/file, press the . button twice.

Press the CD OPEN/CLOSE (L) button to open the disc tray.

< You can also open the tray when in modes other than CD mode.

When playback is stopped or paused

Press a CD Skip (.//) button repeatedly to select the track/

file you want to hear. Then, press the CD Play (t) button or CD

Pause (J) button to start playback of the selected track/file.

Selecting a folder (MP3 disc)

Press the FOLDER ( / ) buttons to select a folder. Then, press

the CD Play (t) button to start playback.

REPEAT 1 REPEAT ALL

(oﬀ)

REPEAT 1 REPEAT ALL

(oﬀ)

REPEAT FOLDER

Repeat playback

This function can be used in CD and USB modes.

Press the REPEAT button to cycle through the following playback modes:

Audio CD

MP3

Shuffle playback

This function can be used in CD and USB modes.

Use this function to play the tracks/files on a disc/USB flash drive in random order.

Pressing the SHUFFLE button turns the shuffle mode on and off.

During shuffle playback, “SHUFFLE” appears on the display.

After playing back all tracks/files, the unit exits the “Shuffle” playback mode and stops playback.

To stop shuffle playback, press the CD/USB Stop (H) button.

< If any of the following buttons are pressed, the repeat mode will

be canceled.

In CD mode

POWER button, SOURCE button, CD OPEN/CLOSE (L) button, REPEAT button, SHUFFLE button

In USB mode

POWER button, SOURCE button, REPEAT button, SHUFFLE button

REPEAT 1 (Repeat one track/file)

The track/file being played will be played repeatedly. “REPEAT 1” appears on the display.

< If you use the CD/USB Skip (. or /) buttons to select a

different track/file, that track/file will be played repeatedly.

< You can select a track/file to be repeated when playback is

stopped. Press the REPEAT button, select a track/file using the CD/ USB Skip (. or /) buttons, and then press the CD/USB Play (t) button or CD/USB Pause (J) button to start playback.

< If you press the / button during shuffle playback, the next

track/file will be randomly selected and played. If you press the . button, the currently played track/file will be played from the beginning. During shuffle playback, a track/file that has completed playback will not be played again.

< The shuffle function does not work during program playback.

< If any of the following buttons are pressed, shuffle mode will be

canceled.

In CD mode

POWER button, SOURCE button, CD OPEN/CLOSE (L) button, REPEAT button, SHUFFLE button

In USB mode

POWER button, SOURCE button, REPEAT button, SHUFFLE button

REPEAT ALL (Repeat all tracks/files)

All the tracks/files on the disc will be played repeatedly. “REPEAT ALL” appears on the display.

< During program playback, the programmed tracks/files will be

played repeatedly.

REPEAT FOLDER (Repeat all the files in a folder) (MP3 only)

All the files in the selected folder will be played repeatedly. “REPEAT FOLDER” appears on the display.

Programmed playback

This function can be used in CD and USB modes.

Up to 30tracks/files can be programmed in the desired order.

When playback is stopped, press the PROGRAM button

to enter program mode.

“PROGRAM” blinks and “P-01” appears on the display.

Example when in CD mode

Press the CD/USB Skip (. or /) buttons to select a

track/file, then press the PROGRAM button.

The track/file is programmed, and “P-02” is displayed.

< Repeat steps 2 and 3 to program more tracks/files.

< You can program up to 30tracks/files.

< To stop programming, press the CD/USB Stop (H ) button.

Programming is canceled, but the program contents are retained in memory. If you want to restart program playback, press the PROGRAM button, and then press the CD/USB Play (t) button.

ENGLISH

< To stop programming, press the CD/USB Stop (H ) button.

(When programming MP3 files)

Press the CD/USB FOLDER ( / ) buttons to select a folder, then press the PROGRAM button.

< MP3 files not located in a specific folder are in the “001” (ROOT)

folder.

NOTE

The ROOT folder is the top-level folder.

When the selection of track/file numbers is completed,

press the CD/USB Play (t) button to start program playback.

To stop program playback, press the CD/USB Stop (H) button.

< After program playback finishes, press the PROGRAM button

and then the CD/USB Play (t) button to play the program again.

< You can use the CD/USB Skip (. and /) buttons during

program playback to select and play other tracks/files in the program.

< The shuffle function does not work during program playback.

< “REPEAT 1” and “REPEAT ALL” playback are possible during

program playback. When set to “REPEAT ALL” mode, the programmed tracks/files will be played repeatedly.

Program number to be changed

Programmed playback (continued)

Adding tracks/files to the end of the program

When playback is stopped, press the PROGRAM button repeatedly until “TRACK 00” appears on the display.

Press repeatedly

Select a track/file number you want to add using the CD/USB Skip (. and /) buttons, and then press the PROGRAM button.

Overwriting part of the program

When playback is stopped, press the PROGRAM button repeatedly

until the program number of the track that you want to change appears on the display.

Press repeatedly

Select the track/file number that you want to add using the CD/ USB Skip (. and /) buttons, and then press the PROGRAM button.

The track/file is added to the end of the program.

The selected track/file is added to the program, replacing the track that had been at that program number before.

Checking the program order

Program number to be deleted

Clearing the program

Press repeatedly

When playback is stopped, press the PROGRAM button repeatedly. The numbers of the programmed tracks/files and their program numbers will be shown in order.

Deleting tracks/files from the program

When playback is stopped, press the PROGRAM button repeatedly until the program number of the track to be deleted appears on the display.

Press repeatedly

Press at least 1second

When playback is stopped, press the PROGRAM button, followed

by the CLEAR button or CD/USB Stop (H) button more than 1

second.

The PROGRAM indicator disappears and all the contents of the

program are cleared.

< If the PROGRAM indicator is not shown, press the PROGRAM button

to activate program mode before pressing the CLEAR button.

< If one of the following buttons is pressed, the contents of the

program are also cleared.

In CD mode

POWER button, CD OPEN/CLOSE (L) button, SOURCE button

In USB mode

POWER button, SOURCE button

ENGLISH

Press the CLEAR button.

The track/file is deleted from the program.

Exiting program mode

Press at least 1second

When playback is stopped, press and hold the PROGRAM button

more than 1second or press the CD/USB Stop (H) button. The

PROGRAM indicator will disappear.

< This does not clear the contents of the program. Press the PROGRAM

button again and then press the CD/USB Play (t) button if you want

to restart program playback.

Listening to a cassette tape

You can play Normal (type ), Chrome (type ) and Metal (type ) tapes with this unit.

Press the SOURCE button repeatedly to select “TAPE”.

< When a different source is selected, starting tape playback

automatically selects the tape.

Press the TAPE EJECT (L) button to open the cassette

tape compartment.

Press the TAPE play (t) button to start playback.

Pausing playback temporarily

Put a cassette tape in the compartment.

Insert the cassette tape with its open edge facing down and the side that you want to play facing you. Then, close the cassette compartment by pushing its door in.

Press the TAPE Pause (J) button during playback to stop playback at the current position. To resume playback, press the TAPE Pause (J ) button again or press the TAPE Play (t) button.

Stopping playback

Press the TAPE Stop (H) button to stop playback.

ATTENTION

o Do not use deformed or slack cassette tapes. The tape could

become tangled, and the cassette might become stuck in the unit.

o Do not force the door of the compartment by hand when

opening it.

Failure to follow any of the above could cause malfunction.

Opening the cassette tape compartment

When the tape is stopped, press the TAPE EJECT (L) button to open the cassette tape compartment.

o Do not press the TAPE EJECT (-) button during playback. o You can also open the compartment when in modes other than

TAPE mode.

Fast-forwarding/Rewinding a tape

Pitch control

This control varies the pitch of the music during playback.

Turning the PITCH CONTROL knob clockwise increases the playback

speed and raises the pitch by a maximum of +10%.

Turning the PITCH CONTROL knob counterclockwise reduces the

playback speed and lowers the pitch by a maximum of −10%.

o This does not function when recording to tape. o Keep it set to the 12 o’clock (vertical) position for normal pitch.

Tape counter

ENGLISH

Press the Fast-forward (,) button or the Rewind (m) button to wind the tape rapidly.

Winding stops when the end of the tape is reached. To stop winding before the end, press the TAPE Stop (H) button.

< You can wind the tape when CD/USB/LINE is selected as a source.

These buttons do not, however, function when in a recording mode.

Press the COUNTER RESET button to reset the tape counter to

“0000”. You can use this function to easily locate any desired point

on the tape.

Listening to files on a USB flash drive

ATTENTION

Press the SOURCE button repeatedly to select “USB”.

< When a different source is selected, starting USB playback

automatically selects the USB mode.

Press the USB Play (t) button to start playback.

< When playback of all the files has finished, the unit stops

automatically.

< MP3 files that are not put in folders are automatically put in the

“ROOT” folder. Playback starts from the first file in the ROOT folder.

< See page 40 for information about the playback order of MP3

files.

Connect an external USB flash drive to the USB port of

this unit.

Reading the USB flash drive takes a few seconds. USB flash drives with especially large capacities might take more time. When “READING” is shown while the drive is being read, pressing buttons will have no effect.

< If no MP3 file is on the USB flahs drive, “NO MUSIC FILE” is

displayed.

Pausing playback temporarily

Press the USB Pause (J) button during playback to stop playback at the current position. To resume playback, press the USB Pause (J) button again or press the USB Play (t) button.

Stopping playback

Skipping to an earlier or later file

Press the USB Stop (H) button to stop playback.

Search for a part of a file

Press and hold

During playback, hold down a USB Search (. or /) button to search for a part of a file. Pressing and holding a Search button increases the search speed. Release it when you find the beginning of the part that you want to hear.

During playback

Press a USB Skip (.//) button repeatedly until the desired

file is selected. The selected file will be played from the beginning.

< If the . button is pressed once during playback, the file being

played will be played again from the beginning. To return to the

beginning of the previous file, press the . button twice.

When playback is stopped or paused

Press a USB Skip (.//) button repeatedly to select the file

you want to hear. Then, press the USB Play (t) button or USB

Pause (J) button to start playback of the selected file.

Selecting a folder

ENGLISH

Press the FOLDER ( / ) buttons to select a folder. Then, press

the USB Play (t) button to start playback.

Repeat, shuffle and programmed playback

These functions can be used in USB mode. Please see the following sections for details about using them.

Repeat playback Shuffle playback Programmed playback e page 21

page 20

Recording on a USB flash drive

This unit can record sound from a CD, cassette tape or connected external device in MP3 format to a USB flash drive.

o This unit can also record to cassette tape, but it cannot record to

both USB flash drive and tape at the same time.

o Correct recording might not be possible depending on the USB

flash drive. If this occurs, try using a different USB flash drive.

o This unit cannot record to a USB flash drive with the timer record-

ing function.

o You can mix in the sound of a mic connected to this unit when

recording (page 34).

o When recording from a CD to a USB flash drive, the monitored

sound might skip depending on the type of USB flash drive, but this will not affect the recorded data.

ATTENTION

Do not disconnect the USB flash drive during recording. Do not turn the unit off or disconnect the power cord during recording. Doing so might cause damage to the unit and the connected USB flash drive.

About recorded MP3 files

Connect an external USB flash drive to the USB port of

this unit.

< You cannot record to an external USB flash drive if there is no

free space or the device is locked.

< Before recording, check the remaining capacity of the USB flash

drive using a PC. You cannot check the remaining memory capacity with this unit.

Press the SOURCE button repeatedly to select the source

to be recorded (CD, TAPE, or LINE).

< When recording, “RECORD” folder is automatically created and a

subfolder for each source (“CD”, “TAPE” or “LINE”) is also created in the “RECORD” folder. MP3 files are added to the corresponding subfolder.

< File names are assigned automatically with a numerical endings in

order.

When recorded from a CD

“CD001.MP3”, “CD002.MP3” …

If there are, for example, files named “CD004.MP3” and “CD009. MP3” in the USB folder already, and you make a recording, the next new file will be named “CD010.MP3”.

When recorded from a cassette tape

“T001.MP3”, “T002A.MP3“ …

When record from an external source

“L001.MP3”

< During recording from a tape or LINE input, you can divide the file

manually (page 30). In this case, consecutive numbers are added to the ends of the file names.

Example:

If “T001.MP3” is divided, files named “T001.MP3” and “T002.MP3” are created.

< This unit can record up to 999files to a USB flash drive. However, if

the USB flash drive already contains files, those files are included in the maximum total of 999 files when recording.

Press the RECORD USB button to start recording standby.

The red indicator above the RECORD USB button and the icon on the display blink.

o Preparation for USB recording takes a few seconds.

USB flash drives with especially large capacities might take

more time.

When “Record prepare” is shown during preparation, pressing

buttons will have no effect. o To stop recording, press the USB Stop (H) button.

< The maximum time possible for a recorded file is 240minutes.

< Tracks recorded onto a USB flash drive are converted to MP3 files at

a bit rate of 128kbps.

(When recording from a tape or an external source)

Adjust the recording level.

Before recording, adjust the recording level. Failure to do so could cause the recorded sound to be distorted or noisy.

1. Play the source (cassette tape or external source) to be

recorded.

2. Use the REC LEVEL knob to adjust the recording level so that

the loudest sound never lights the “OVER” indicator on the peak level meter.

Press the RECORD USB button again to start recording.

When recording from an external source, you must also start playback of that source.

If the recording source is a CD or cassette tape, that source will automatically start playing back.

o Pressing either the USB Pause (9) or USB Play (t) button will

start recording.

The red indicator above the RECORD USB button and the icon on the display stop blinking.

o If the USB flash drive runs out of open space during recording,

recording stops automatically.

ENGLISH

< Different sources to be recorded have different volumes. In

order to record at the optimal volume for each source, it is necessary to adjust the recording level for each source.

< When recording from a CD, the recording level does not

need to be changed, and it cannot be adjusted.

Prepare the recording source.

Recording from a CD

To record all the tracks/files on a CD, stop the disc first. To record only some of the tracks/files on a CD, pause at the beginning of the part that you want to record. You can also record tracks in programmed order. For information about how to set the program, see page 21.

Recording from a cassette tape

To record the entire tape, rewind the tape to its starting point. To record from the middle of a tape, stop or pause at the point from where you want to start recording.

Recording from an external source

Prepare to start playback of the source device.

o To pause recording, press the USB Pause (J) button. A second

press of the button resumes recording. Pressing the RECORD USB or USB Play (t) button will also

resume recording. You can also resume recording by pressing the source playback button if the recording source is a CD or tape.

o You can mix in the sound of a mic connected to this unit when

recording (page 34).

o You cannot mix in the sound of a mic connected to this unit

when recording from a CD to a USB flash drive.

Recording from a CD or a cassette tape

When source playback stops, recording also automatically stops. To stop recording, press the USB Stop (H) button. Doing this also stops playback of the recording source.

o When recording from a CD to a USB flash drive, the monitored

sound might skip depending on the type of USB flash drive, but this will not affect the recorded data.

Recording from an external source

When source playback stops, recording does not automatically stop. Press the USB Stop (H) button to stop recording.

Example: Set the source selection of an amplifier. Set the playback media in a connected player. To record from a tuner, tune in a station.

Recording on a USB flash drive (contd.)

Manual file division

When recording from a tape or a device connected to the LINE inputs, you can manually divide the MP3 file as it is being recorded. This function cannot be used when recording from a CD. A recorded CD will automatically be divided at each track.

During recording, press the RECORD USB button at the point where you want to divide the recorded file. File division takes about 10 seconds.

Erasing files from a USB flash drive

ATTENTION

Do not disconnect the USB flash drive during erasing. Do not turn the unit off or disconnect the power cord during erasing. Doing so might cause damage to the unit and the connected USB flash drive.

Erasing all files

ATTENTION

Using this function will erase all the contents of a USB flash drive. Non-audio files that are not recognized by this unit will also be erased. Confirm that this is acceptable before beginning this operation.

Press the SOURCE button repeatedly to select “USB”.

o “File increment” appears on the display during division.

o “Record Ending” will appear when you press the USB stop (8)

button.

When recording from a tape:

During file division, the tape stops, but almost no gap in the recording should occur.

When recording from the LINE inputs:

During file division, a gap will occur in the recording.

< This unit cannot divide an already recorded MP3 file. This function

only works during recording.

< Consecutive numbers are added to the end of the file names after

division.

Example:

If “T001.MP3” is divided, files named “T001.MP3” and “T002.MP3” are created.

Connect an external USB flash drive to the USB port of

this unit.

Press the ERASE button for more than 2seconds.

Press at least 2second

“Erase all?” appears on the display.

Within 6seconds, press the ERASE button again.

The USB flash drive is completely erased. “NO MUSIC FILE” appears on the display.

+ 98 hidden pages

Teac AD-850 Owners Manual

Specifications and Main Features

Frequently Asked Questions

User Manual