Taylor PH61 Specifications

Rockton, Illinois 61072

800-255-0626

Phone [phone] Fax [phone]

www.taylor-company.com

e-mail: [e-mail]

International Office
Taylor Company S.r.l.
Roma, Italy
Tel: [phone] Fax: [phone]
e-mail: [e-mail]

PH61

Item No.

_______________________________

PH61

Offer four separate shake flavors: chocolate, vanilla,
strawberry and an optional flavor. Portion controlled shake
dispensing for high volume milkshake production.

Heat Treatment System

Provides a daily heating and cooling cycle to safely maintain dairy
products up to two weeks before a complete disassembly and
cleaning is required.

Freezing Cylinder

One, 7 quart (6.6 liter).

Mix Hopper

One, 20 quart (18.9 liter). Refrigerated to maintain mix below 41ºF
(5ºC).

Indicator Lights

Mix Low light flashes to alert the operator to add mix. When the
Mix Out light flashes, the unit automatically goes into Standby mode
to prevent damage.

Electronic Controls

Viscosity is continually measured to serve consistent quality shakes.
The LCD (Liquid Crystal Display) readout will identify temperatures
in the hopper or freezing cylinder at any point of operation. History
of temperatures and times during the last 13 heat cycles may be
viewed.

Standby

During long no-use periods, the standby feature maintains safe
product temperatures in the mix hopper and freezing cylinder.

Syrup System

Shake flavors are selected from touch pads. Self-contained air
compressor delivers shake syrup from three, 1 gallon (3.8 l) syrup
tanks located in the lower front compartment. Frozen shake mix
and syrup automatically blends to dispense the chosen flavor. Use
only single strength syrup, free from pulp and seeds.

Features

Shake Freezer

Four Flavor, Pump

PH61

PH61Shake Freezer

Electrical

One dedicated electrical connection is required. See the Electrical chart for
the proper electrical requirements. Manufactured to be permanently
connected. Consult your local Taylor distributor for cord & receptacle
specifications as local codes allow.

Beater Motor

One, 1.0 HP

Refrigeration System

One, 11,000 BTU/hr. R404A.
(BTUs may vary depending on compressor used.)

Air Cooled

Minimum Clearance: 6” (152 mm) on all sides. Minimum air clearances must
be met to assure adequate air flow for optimum performance.

Water Cooled

Water inlet and drain connections under side of base 3/8” FPT.

Printed in U.S.A.

Weights lbs. kgs.

Net 608 275.8
Crated 650 294.8

cu. ft. cu. m.

Volume 66.5 1.88

Dimensions in. mm.

Width 18-7/16 468
Depth 35-1/4 895
Height 59-1/2 1511
Floor Clearance 7-1/2 191

*Mounted on standard casters

Bidding Specs

Electrical: Volt ___________________ Hz__________ ph _________

Neutral:  Yes No Cooling:  Air  Water  NA

Options:_________________________________________________
_________________________________________________________

 Faucet
 Hopper Locks
 Shake Cup Dispenser

Options

Specifications

046338-ADV

2/06

Continuing research results in steady improvements; therefore, these

specifications are subject to change without notice.

Taylor Company,

A Division of Carrier Commercial Refrigeration, Inc.
Rockton, Illinois 61072
815-624-8333 800-255-0626 Fax [phone]

www.taylor-company.com

Electrical Maximum Minimum Poles (P)

Fuse Size Circuit Ampacity Wires (W)

208-230/60/3 Air 25 19 3P 4W
208-230/60/3 Water 25 18 3P 4W
220-240/50/3 Air 25 18 3P 4W
380-415/50/3N~ Air 20 16 4P 5W

This unit may be manufactured in other electrical characteristics. Refer to the
local Taylor Distributor for availability.
(For exact electrical information, always refer to the data label of the unit.)